coreboot May 2010

coreboot@coreboot.org

59 participants
300 discussions

Re: [coreboot] Wyse S10 Information
by Nils 28 May '10

28 May '10

Oliver wrote: >The reason why it's not working now, is because I get a message from >the pata_cs5536 driver that IDE is disabled by the bios; and of course >no option to enable it. This is the same problem i had with the S50. The problem is that the bios has configured the CS5536 for flash(board). You have to enable the flash driver in the kernel(MTD? i think) It is not a usual ide device. >Also, I can boot a Ubuntu 10.04 USB stick (syslinux basically) and pxe >with the module present, but I cannot seem to boot a USB stick with >just grub on it, if the IDE module is in place. I think grub tries to >probe the IDE device, but fails or is on an extremly long timeout. >Strings revealed usernames, hostnames etc used by the OS/rdp/ica >clients in the bios.rom I extracted; I cannot belive a flash image >somewhere would write it's information into the flash chip. I'm very >convinced that wyse OS is somewhere in the 2Megabyte flash and (even >according to the specs) that is all that is available to the >thinclient. Ok the flashrom chip in the S50 is 256KB. In the S50 only the bios is in the chip. The operating system "Linux v6" is on the flashboard. Nils.

3 3

Re Gateway m1622h support?
by anders＠jenbo.dk 28 May '10

28 May '10

The sb and nb are bother supported (although the nb is listed as sb), a cousin of your SuperIO is supported so getting it working shouldn't be to hard (you will need it for debugging). The flashrom is not detected, you need to visually identify it and talk to the guys at #flashrom about getting it working, or use a different rom to test with (you still need to identify it so you can get one that matches it). Mvh Anders ----- Reply message ----- Fra: "MIKE WATTERS" <mikewatters(a)hotmail.com> Dato: fre., maj 28, 2010 07:59 Emne: [coreboot] Gateway m1622h support? Til: <coreboot(a)coreboot.org>

1 0

Gateway m1622h support?
by MIKE WATTERS 28 May '10

28 May '10

not sure if it is or not, however, here is the details as attachments. board product specs at this url: http://support.gateway.com/s/Mobile/2008/Avalon/4006274R/4006274Rsp2.shtml

1 0

Re: [coreboot] Wyse S10 Information
by Oliver Schinagl 28 May '10

28 May '10

On 05/28/2010 12:30 AM, Nils wrote: > Hi Oliver, > You wrote: > >> I'll check the rom as advised on the list; but I wouldn't be supprised >> if it was; the IDE port is free and unused >> > I think the operating system is in your ide flash board that is laying > upside down in the corner of your S10 on the photo.(it belongs in the > ide slot) > > >> I then wonder, how the S50 would look like and compares to the S10 ... >> > I`l send you a few photos.(i don`t know if the big photos are > appreciated on the list) > But i can say that on first glance it looks like they are the same. > > Greetings,Nils > > Your board looks identical. like exactly the same. I notice you have a pin in BT1? is that to hook up an internal mini battery to keep the bios from resetting? I notice you removed your bioschip as well, I take it that's for testing? I doubt the unit does anything without the bios? Also I bet, that that IDE flash module yours has, is the 128mb flash from the specs. This confirms my suspicion that the S*0 series don't utilize the onboard flash possibility the CS5536 has. I read in the specs of the CS5535/6 that you can use the bios to choose whether to use one of the ports as an external IDE port, or internal flash device (I doubt it's in the geode chip) but you have to use the bios to activate one of the two, but never both at the same time. Since the S10 does try to boot from the IDE module (based on activity led on it) when selecting the IDE option (PXE/USB/IDE are the only options) it can enable it successfully. However if it is not booting from IDE module, it disables the IDE ports. If I could only get something bootable into that socket, I'd be able to take it from there ... I'm thinking now of using setpci to just force the port on and hope for the best. BTW, do you actually have Coreboot +seabios working on an S50? Also could you paste me your lspci -vvvnnn; specifically for the IDE controller? Thanks, Oliver

1 0

[commit] r5595 - trunk/src/northbridge/intel/i82830
by repository service 28 May '10

28 May '10

Author: stepan Date: Fri May 28 00:47:13 2010 New Revision: 5595 URL: https://tracker.coreboot.org/trac/coreboot/changeset/5595 Log: Fix MBI walker. Signed-off-by: Joseph Smith <joe(a)settoplinux.org> Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Joseph Smith <joe(a)settoplinux.org> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/src/northbridge/intel/i82830/i82830_smihandler.c Modified: trunk/src/northbridge/intel/i82830/i82830_smihandler.c ============================================================================== --- trunk/src/northbridge/intel/i82830/i82830_smihandler.c Thu May 27 17:41:15 2010 (r5594) +++ trunk/src/northbridge/intel/i82830/i82830_smihandler.c Fri May 28 00:47:13 2010 (r5595) @@ -196,7 +196,7 @@ } mbi_header = (mbi_header_t *)&mbi[i]; - len = ALIGN((mbi_header->size * 16) + sizeof(mbi_header) + mbi_header->name_len, 16); + len = ALIGN((mbi_header->size * 16) + sizeof(mbi_header) + ALIGN(mbi_header->name_len, 16), 16); if (obj_header->objnum == count) { #ifdef DEBUG_SMI_I82830 @@ -205,7 +205,7 @@ break; } #endif - int headerlen = ALIGN(sizeof(mbi_header) + mbi_header->name_len + 15, 16); + int headerlen = ALIGN(sizeof(mbi_header) + ALIGN(mbi_header->name_len, 16), 16); #ifdef DEBUG_SMI_I82830 printk(BIOS_DEBUG, "| |- headerlen = %d\n", headerlen); #endif @@ -245,7 +245,7 @@ getobj->banner.retsts = MSH_IF_NOT_FOUND; for (i=0; i< mbi_len;) { - int len; + int headerlen, objectlen; if (!(mbi[i] == 0xf0 && mbi [i+1] == 0xf6)) { i+=16; @@ -253,21 +253,23 @@ } mbi_header = (mbi_header_t *)&mbi[i]; - len = ALIGN((mbi_header->size * 16) + sizeof(mbi_header) + mbi_header->name_len, 16); + headerlen = ALIGN(sizeof(mbi_header) + ALIGN(mbi_header->name_len, 16), 16); + objectlen = ALIGN((mbi_header->size * 16), 16); if (getobj->objnum == count) { - printk(BIOS_DEBUG, "| |- len = %x\n", len); + printk(BIOS_DEBUG, "| |- len = %x\n", headerlen + objectlen); + memcpy((void *)(getobj->buffer + OBJ_OFFSET), - ((char *)mbi_header) + 0x20 , (len > getobj->buflen) ? getobj->buflen : len); + ((char *)mbi_header) + headerlen, (objectlen > getobj->buflen) ? getobj->buflen : objectlen); getobj->banner.retsts = MSH_OK; #ifdef DEBUG_SMI_I82830 dump((u8 *)banner_id, sizeof(*getobj)); - dump((u8 *)getobj->buffer + OBJ_OFFSET, len); + dump((u8 *)getobj->buffer + OBJ_OFFSET, objectlen); #endif break; } - i += len; + i += (headerlen + objectlen); count++; } if (getobj->banner.retsts == MSH_IF_NOT_FOUND)

1 0

Re: [coreboot] segmentation fault when building
by Peter Stuge 27 May '10

27 May '10

Hi Anthony, Mayhall, Anthony J. (MSFC-ES53)[Dynamic Concepts Inc.] wrote: > If I run make menuconfig and select the Tyan S2912_fam10 > motherboard, when I do the make, I get an error from the loader. > Here's what the output looks like: > > ROMCC mainboard/tyan/s2912_fam10/bootblock.inc > GEN bootblock/bootblock.c > CC mainboard/tyan/s2912_fam10/bootblock.s > CC mainboard/tyan/s2912_fam10/bootblock.o > GEN bootblock/ldscript.ld > LINK bootblock.elf > collect2: ld terminated with signal 11 [Segmentation fault] > make: *** [build/bootblock.elf] Error 1 > > Can anyone tell me why this is happening? coreboot triggers many issues in distribution toolchains, so if you get strange behavior or odd build problems then it's a good idea to use a clean toolchain for building coreboot. The script util/crossgcc/buildgcc automates the building, and coreboot build system will pick up the default output from buildgcc automatically. Give that a try. //Peter

1 0

[PATCH] Improve i82830 MBI SMI Handler
by Joseph Smith 27 May '10

27 May '10

This patch improves the i82830 MBI SMI Handler. It is now able to load Intel vbios VBT and Flexaim modules. Build and boot tested. Signed-off-by: Joseph Smith <joe(a)settoplinux.org> -- Thanks, Joseph Smith Set-Top-Linux www.settoplinux.org

3 10

segmentation fault when building
by Mayhall, Anthony J. (MSFC-ES53)[Dynamic Concepts Inc.] 27 May '10

27 May '10

If I run make menuconfig and select the Tyan S2912_fam10 motherboard, when I do the make, I get an error from the loader. Here's what the output looks like: ROMCC mainboard/tyan/s2912_fam10/bootblock.inc GEN bootblock/bootblock.c CC mainboard/tyan/s2912_fam10/bootblock.s CC mainboard/tyan/s2912_fam10/bootblock.o GEN bootblock/ldscript.ld LINK bootblock.elf collect2: ld terminated with signal 11 [Segmentation fault] make: *** [build/bootblock.elf] Error 1 Can anyone tell me why this is happening? Thanks, Anthony Mayhall Dynamic Concepts, Inc. (256)544-7620

1 0

Patch for Nokia-IP530, now with working PIRQ table
by mbertens 27 May '10

27 May '10

Signed-off-by: Marc Bertens <mbertens(a)xs4all.nl> Hello all, Here is the update for the Nokia IP530 system. it has now working NICs and correct PIRQ table. corrections where made to serveral files. Currently the PCMCIA controller need some more work, it uses a PCI1225 of Texas Instruments. Any help with this is appreciated. Marc.

6 30

[commit] r5594 - in trunk/src: devices/oprom/yabel northbridge/intel/i82830 southbridge/intel/i82801dx
by repository service 27 May '10

27 May '10

Author: stepan Date: Thu May 27 17:41:15 2010 New Revision: 5594 URL: https://tracker.coreboot.org/trac/coreboot/changeset/5594 Log: fix warnings. Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/src/devices/oprom/yabel/device.c trunk/src/northbridge/intel/i82830/i82830_smihandler.c trunk/src/southbridge/intel/i82801dx/i82801dx_smihandler.c Modified: trunk/src/devices/oprom/yabel/device.c ============================================================================== --- trunk/src/devices/oprom/yabel/device.c Wed May 26 19:08:13 2010 (r5593) +++ trunk/src/devices/oprom/yabel/device.c Thu May 27 17:41:15 2010 (r5594) @@ -44,7 +44,6 @@ biosemu_dev_get_addr_info(void) { int taa_index = 0; - int i = 0; struct resource *r; u8 bus = bios_device.dev->bus->link; u16 devfn = bios_device.dev->path.pci.devfn; @@ -115,6 +114,7 @@ //dump translate_address_array printf("translate_address_array: \n"); translate_address_t ta; + int i; for (i = 0; i <= taa_last_entry; i++) { ta = translate_address_array[i]; printf Modified: trunk/src/northbridge/intel/i82830/i82830_smihandler.c ============================================================================== --- trunk/src/northbridge/intel/i82830/i82830_smihandler.c Wed May 26 19:08:13 2010 (r5593) +++ trunk/src/northbridge/intel/i82830/i82830_smihandler.c Thu May 27 17:41:15 2010 (r5594) @@ -217,7 +217,7 @@ printk(BIOS_DEBUG, "%c", mbi_header->name[j]); printk(BIOS_DEBUG, "' found.\n"); #ifdef DEBUG_SMI_I82830 - dump(banner_id, sizeof(obj_header_t) + 16); + dump((u8 *)banner_id, sizeof(obj_header_t) + ALIGN(mbi_header->name_len, 16)); #endif break; } @@ -233,7 +233,7 @@ mbi_header_t *mbi_header = NULL; printk(BIOS_DEBUG, "|- MBI_GetObject\n"); #ifdef DEBUG_SMI_I82830 - printk(BIOS_DEBUG, "| |- handle = %016lx\n", getobj->handle); + printk(BIOS_DEBUG, "| |- handle = %016Lx\n", getobj->handle); #endif printk(BIOS_DEBUG, "| |- objnum = %d\n", getobj->objnum); printk(BIOS_DEBUG, "| |- start = %x\n", getobj->start); @@ -262,8 +262,8 @@ getobj->banner.retsts = MSH_OK; #ifdef DEBUG_SMI_I82830 - dump(banner_id, sizeof(*getobj)); - dump(getobj->buffer + OBJ_OFFSET, len); + dump((u8 *)banner_id, sizeof(*getobj)); + dump((u8 *)getobj->buffer + OBJ_OFFSET, len); #endif break; } Modified: trunk/src/southbridge/intel/i82801dx/i82801dx_smihandler.c ============================================================================== --- trunk/src/southbridge/intel/i82801dx/i82801dx_smihandler.c Wed May 26 19:08:13 2010 (r5593) +++ trunk/src/southbridge/intel/i82801dx/i82801dx_smihandler.c Thu May 27 17:41:15 2010 (r5594) @@ -449,8 +449,6 @@ dump_gpe0_status(gpe0_sts); } -void __attribute__((weak)) mainboard_smi_gpi(u16 gpi_sts); - static void southbridge_smi_gpi(unsigned int node, smm_state_save_area_t *state_save) { u16 reg16;

1 0

← Newer
1
2
3
4
5
6
7
8
9
...
30
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot May 2010