by Masoud Fatollahy
Hi,
Why is it problem to boot from an usb port when we are using linuxbios and
filo. as I can see all usb code are there, what is missing?
Thanks,
/Masoud
by Robert Millan
This patch includes config files for the asus/a8n5x port. It is the same as
asus/a8n_e with a different pnp layout, so I used #include's whenever possible.
System boots and is usable with usb keyboard.
works:
- serial port
- vga (old pci card)
- memtest86+ succeeds, but only with Rudolf's patch for unbuffered dimms
in K8. Otherwise you get spurious memory corruption.
- ide disk
- usb
doesn't:
- ps/2 keyboard
- onboard ethernet
- vga pci-e card (??)
- any other pci card I tried
wasn't tested:
- sata
- game port
- onboard audio (not supported by alsa anyway)
- ps/2 mouse
--
Robert Millan
<GPLv2> I know my rights; I want my phone call!
<DRM> What use is a phone call, if you are unable to speak?
(as seen on /.)
by Myles Watson
Is there a magic number for LZMA? Should there be?
I accidentally used an uncompressed payload with v2 when it expected a
compressed payload, and it gave me the message:
Decoder scratchpad too small!!
Decoding error = 1
I think it would be nicer to have an error like:
Payload not compressed with lzma!
Myles
by Carl-Daniel Hailfinger
i440bxemulation is missing the 640k-1024k mem hole.
geodelx has the hole.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Index: LinuxBIOSv3-stuff/northbridge/intel/i440bxemulation/i440bx.c
===================================================================
--- LinuxBIOSv3-stuff/northbridge/intel/i440bxemulation/i440bx.c (Revision 644)
+++ LinuxBIOSv3-stuff/northbridge/intel/i440bxemulation/i440bx.c (Arbeitskopie)
@@ -59,7 +59,10 @@
mc_dev = dev->link[0].children;
if (mc_dev) {
idx = 10;
- ram_resource(dev, idx++, 0, tolmk);
+ /* 0 .. 640 KB */
+ ram_resource(dev, idx++, 0, 640);
+ /* 1 MB .. (Systop - 1 MB) (in KB) */
+ ram_resource(dev, idx++, 1024, tolmk - 1024);
}
phase4_assign_resources(&dev->link[0]);
}
--
http://www.hailfinger.org/
by Carl-Daniel Hailfinger
Convert stage2 and initram makefile rules from object to source files.
This creates a clearer distinction between source files in the source
tree we want to have compiled and indirectly created object/source files
in the object tree.
It also will make enable us to move to whole-program
optimization/compilation which should yield substantial size savings.
Then again, we may be able to do that without the makefile conversion as
well.
This is a RFC, not to be applied immediately.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net>
Index: LinuxBIOSv3-makefilerewrite/southbridge/amd/cs5536/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/southbridge/amd/cs5536/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/southbridge/amd/cs5536/Makefile (Arbeitskopie)
@@ -21,7 +21,7 @@
ifeq ($(CONFIG_SOUTHBRIDGE_AMD_CS5536),y)
-STAGE2_CHIPSET_OBJ += $(obj)/southbridge/amd/cs5536/cs5536.o
+STAGE2_CHIPSET_SRC += $(src)/southbridge/amd/cs5536/cs5536.c
STAGE0_CHIPSET_OBJ += $(obj)/southbridge/amd/cs5536/stage1.o
Index: LinuxBIOSv3-makefilerewrite/southbridge/intel/i82371eb/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/southbridge/intel/i82371eb/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/southbridge/intel/i82371eb/Makefile (Arbeitskopie)
@@ -20,6 +20,6 @@
ifeq ($(CONFIG_SOUTHBRIDGE_INTEL_I82371EB),y)
-STAGE2_CHIPSET_OBJ += $(obj)/southbridge/intel/i82371eb/i82371eb.o
+STAGE2_CHIPSET_SRC += $(src)/southbridge/intel/i82371eb/i82371eb.c
endif
Index: LinuxBIOSv3-makefilerewrite/superio/winbond/w83627hf/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/superio/winbond/w83627hf/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/superio/winbond/w83627hf/Makefile (Arbeitskopie)
@@ -25,6 +25,6 @@
STAGE0_CHIPSET_OBJ += $(obj)/device/pnp_raw.o
# Always add to variables, as there could be more than one Super I/O.
-STAGE2_CHIPSET_OBJ += $(obj)/superio/winbond/w83627hf/superio.o
+STAGE2_CHIPSET_SRC += $(src)/superio/winbond/w83627hf/superio.c
endif
Index: LinuxBIOSv3-makefilerewrite/superio/fintek/f71805f/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/superio/fintek/f71805f/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/superio/fintek/f71805f/Makefile (Arbeitskopie)
@@ -24,6 +24,6 @@
STAGE0_CHIPSET_OBJ += $(obj)/device/pnp_raw.o
# Always add to variables, as there could be more than one Super I/O.
-STAGE2_CHIPSET_OBJ += $(obj)/superio/fintek/f71805f/superio.o
+STAGE2_CHIPSET_SRC += $(src)/superio/fintek/f71805f/superio.c
endif
Index: LinuxBIOSv3-makefilerewrite/mainboard/adl/msm800sev/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/adl/msm800sev/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/adl/msm800sev/Makefile (Arbeitskopie)
@@ -21,12 +21,12 @@
STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/northbridge/amd/geodelx/raminit.c \
$(src)/southbridge/amd/cs5536/smbus_initram.c \
$(src)/arch/x86/geodelx/geodelx.c
-STAGE2_MAINBOARD_OBJ =
+STAGE2_MAINBOARD_SRC =
$(obj)/coreboot.vpd:
$(Q)printf " BUILD DUMMY VPD\n"
Index: LinuxBIOSv3-makefilerewrite/mainboard/amd/norwich/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/amd/norwich/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/amd/norwich/Makefile (Arbeitskopie)
@@ -21,12 +21,12 @@
STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/northbridge/amd/geodelx/raminit.c \
$(src)/southbridge/amd/cs5536/smbus_initram.c \
$(src)/arch/x86/geodelx/geodelx.c
-STAGE2_MAINBOARD_OBJ = irq_tables.o
+STAGE2_MAINBOARD_SRC = irq_tables.c
$(obj)/coreboot.vpd:
$(Q)printf " BUILD DUMMY VPD\n"
Index: LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe61/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe61/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe61/Makefile (Arbeitskopie)
@@ -21,11 +21,11 @@
STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/northbridge/amd/geodelx/raminit.c \
$(src)/arch/x86/geodelx/geodelx.c
-STAGE2_MAINBOARD_OBJ =
+STAGE2_MAINBOARD_SRC =
$(obj)/coreboot.vpd:
$(Q)printf " BUILD DUMMY VPD\n"
Index: LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe62/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe62/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/artecgroup/dbe62/Makefile (Arbeitskopie)
@@ -21,11 +21,11 @@
STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/northbridge/amd/geodelx/raminit.c \
$(src)/arch/x86/geodelx/geodelx.c
-STAGE2_MAINBOARD_OBJ = irq_tables.o
+STAGE2_MAINBOARD_SRC = irq_tables.c
$(obj)/coreboot.vpd:
$(Q)printf " BUILD DUMMY VPD\n"
Index: LinuxBIOSv3-makefilerewrite/mainboard/pcengines/alix1c/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/pcengines/alix1c/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/pcengines/alix1c/Makefile (Arbeitskopie)
@@ -21,11 +21,11 @@
STAGE0_MAINBOARD_OBJ := $(obj)/mainboard/$(MAINBOARDDIR)/stage1.o
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/northbridge/amd/geodelx/raminit.c \
$(src)/arch/x86/geodelx/geodelx.c
-STAGE2_MAINBOARD_OBJ = irq_tables.o
+STAGE2_MAINBOARD_SRC = irq_tables.c
$(obj)/coreboot.vpd:
$(Q)printf " BUILD DUMMY VPD\n"
Index: LinuxBIOSv3-makefilerewrite/mainboard/emulation/qemu-x86/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/mainboard/emulation/qemu-x86/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/mainboard/emulation/qemu-x86/Makefile (Arbeitskopie)
@@ -28,10 +28,10 @@
# directory and is built from what was auto.c in v2.
#
-INITRAM_OBJ = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
+INITRAM_SRC = $(src)/mainboard/$(MAINBOARDDIR)/initram.c \
$(src)/mainboard/$(MAINBOARDDIR)/initram_printktest.c
-STAGE2_MAINBOARD_OBJ = vga.o
+STAGE2_MAINBOARD_SRC = vga.c
#
# VPD or SIP ROM or... how does NVIDIA call it?
Index: LinuxBIOSv3-makefilerewrite/device/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/device/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/device/Makefile (Arbeitskopie)
@@ -24,6 +24,6 @@
$(Q)printf " CC $(subst $(shell pwd)/,,$(@))\n"
$(Q)$(CC) $(INITCFLAGS) -c $< -o $@
-STAGE2_DEVICE_OBJ = device.o device_util.o root_device.o \
- pci_device.o pci_ops.o pci_rom.o pnp_device.o pnp_raw.o
+STAGE2_DEVICE_SRC = device.c device_util.c root_device.c \
+ pci_device.c pci_ops.c pci_rom.c pnp_device.c pnp_raw.c
Index: LinuxBIOSv3-makefilerewrite/northbridge/amd/geodelx/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/northbridge/amd/geodelx/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/northbridge/amd/geodelx/Makefile (Arbeitskopie)
@@ -21,9 +21,9 @@
ifeq ($(CONFIG_NORTHBRIDGE_AMD_GEODELX),y)
-STAGE2_CHIPSET_OBJ += $(obj)/northbridge/amd/geodelx/geodelx.o \
- $(obj)/northbridge/amd/geodelx/vsmsetup.o \
- $(obj)/util/x86emu/vm86_gdt.o \
- $(obj)/northbridge/amd/geodelx/grphinit.o
+STAGE2_CHIPSET_SRC += $(src)/northbridge/amd/geodelx/geodelx.c \
+ $(src)/northbridge/amd/geodelx/vsmsetup.c \
+ $(src)/util/x86emu/vm86_gdt.c \
+ $(src)/northbridge/amd/geodelx/grphinit.c
endif
Index: LinuxBIOSv3-makefilerewrite/northbridge/intel/i440bxemulation/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/northbridge/intel/i440bxemulation/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/northbridge/intel/i440bxemulation/Makefile (Arbeitskopie)
@@ -21,6 +21,6 @@
ifeq ($(CONFIG_NORTHBRIDGE_INTEL_I440BXEMULATION),y)
-STAGE2_CHIPSET_OBJ += $(obj)/northbridge/intel/i440bxemulation/i440bx.o
+STAGE2_CHIPSET_SRC += $(src)/northbridge/intel/i440bxemulation/i440bx.c
endif
Index: LinuxBIOSv3-makefilerewrite/arch/x86/Makefile
===================================================================
--- LinuxBIOSv3-makefilerewrite/arch/x86/Makefile (Revision 626)
+++ LinuxBIOSv3-makefilerewrite/arch/x86/Makefile (Arbeitskopie)
@@ -179,27 +179,32 @@
# TODO: This should be compressed with the default compressor.
#
-STAGE2_LIB_OBJ = stage2.o clog2.o mem.o tables.o delay.o \
- compute_ip_checksum.o string.o
+STAGE2_LIB_SRC = stage2.c clog2.c mem.c tables.c delay.c \
+ compute_ip_checksum.c string.c
-STAGE2_ARCH_X86_OBJ = archtables.o coreboot_table.o udelay_io.o
-STAGE2_ARCH_X86_OBJ += pci_ops_auto.o pci_ops_conf1.o pci_ops_conf2.o
-STAGE2_ARCH_X86_OBJ += keyboard.o i8259.o isa-dma.o
+STAGE2_ARCH_X86_SRC = archtables.c coreboot_table.c udelay_io.c
+STAGE2_ARCH_X86_SRC += pci_ops_auto.c pci_ops_conf1.c pci_ops_conf2.c
+STAGE2_ARCH_X86_SRC += keyboard.c i8259.c isa-dma.c
ifeq ($(CONFIG_PIRQ_TABLE),y)
-STAGE2_ARCH_X86_OBJ += pirq_routing.o
+STAGE2_ARCH_X86_SRC += pirq_routing.c
endif
STAGE2_DYNAMIC_OBJ = statictree.o
-STAGE2_OBJ := $(patsubst %,$(obj)/lib/%,$(STAGE2_LIB_OBJ)) \
- $(patsubst %,$(obj)/arch/x86/%,$(STAGE2_ARCH_X86_OBJ)) \
- $(patsubst %,$(obj)/device/%,$(STAGE2_DEVICE_OBJ)) \
- $(patsubst %,$(obj)/mainboard/$(MAINBOARDDIR)/%,$(STAGE2_MAINBOARD_OBJ)) \
- $(patsubst %,$(obj)/mainboard/$(MAINBOARDDIR)/%,$(STAGE2_DYNAMIC_OBJ))
+STAGE2_SRC := $(patsubst %,$(src)/lib/%,$(STAGE2_LIB_SRC)) \
+ $(patsubst %,$(src)/arch/x86/%,$(STAGE2_ARCH_X86_SRC)) \
+ $(patsubst %,$(src)/device/%,$(STAGE2_DEVICE_SRC)) \
+ $(patsubst %,$(src)/mainboard/$(MAINBOARDDIR)/%,$(STAGE2_MAINBOARD_SRC))
-STAGE2_OBJ += $(STAGE2_CHIPSET_OBJ)
+STAGE2_SRC += $(STAGE2_CHIPSET_SRC)
+STAGE2_OBJ := $(patsubst $(src)/%.c,$(obj)/%.o,$(STAGE2_SRC))
+
+# This one is special, but only due to slightly incorrect rules and dependencies.
+# Don't change the dependencies for now.
+STAGE2_OBJ += $(patsubst %,$(obj)/mainboard/$(MAINBOARDDIR)/%,$(STAGE2_DYNAMIC_OBJ))
+
ifeq ($(CONFIG_PCI_OPTION_ROM_RUN),y)
ifeq ($(CONFIG_PCI_OPTION_ROM_RUN_X86EMU),y)
# x86emu wants libgcc
@@ -215,7 +220,7 @@
STAGE2_OBJ_NEEDED = $(filter-out $(STAGE0_OBJ), $(STAGE2_OBJ))
-$(obj)/coreboot.stage2 $(obj)/coreboot.stage2.map: $(obj)/stage0.o $(STAGE2_OBJ_NEEDED)
+$(obj)/coreboot.stage2 $(obj)/coreboot.stage2.map: $(obj)/stage0.o $(STAGE2_OBJ_NEEDED) $(STAGE2_SRC)
$(Q)# leave a .o with full symbols in it for debugging.
$(Q)printf " LD $(subst $(shell pwd)/,,$(@))\n"
$(Q)$(LD) -R $(obj)/stage0.o -Ttext 0x2000 --entry=stage2 \
@@ -249,9 +254,9 @@
$(Q)printf " AS $(subst $(shell pwd)/,,$(@))\n"
$(Q)$(AS) $(obj)/arch/x86/stage0_asm.s -o $@
-$(obj)/coreboot.initram $(obj)/coreboot.initram.map: $(obj)/stage0.init $(obj)/stage0-prefixed.o $(INITRAM_OBJ)
+$(obj)/coreboot.initram $(obj)/coreboot.initram.map: $(obj)/stage0.init $(obj)/stage0-prefixed.o $(INITRAM_SRC)
$(Q)printf " CC $(subst $(shell pwd)/,,$(@)) (XIP)\n"
- $(Q)$(CC) $(INITCFLAGS) -D_SHARED -fPIE -c -combine $(INITRAM_OBJ) -o $(obj)/coreboot.initram_partiallylinked.o
+ $(Q)$(CC) $(INITCFLAGS) -D_SHARED -fPIE -c -combine $(INITRAM_SRC) -o $(obj)/coreboot.initram_partiallylinked.o
$(Q)# initram links against stage0
$(Q)printf " LD $(subst $(shell pwd)/,,$(@))\n"
$(Q)$(LD) -Ttext 0 --entry main -N -R $(obj)/stage0-prefixed.o \
--
http://www.hailfinger.org/
by Tiago Marques
On two boards, one MCP55 based and another CK804, if I flash the
proprietary BIOS with: flasrom -wv bios.bin
Verification fails and if I try to boot, it doesn't. Have to flash the
BIOS in another board based on K8T890 that I have. In that one all
works fine, with both BIOS chips I have - one winbond and a PMC.
Haven't tried flashing coreboot due to lack of support.
Since the chipsets are support, this isn't supposed to happen, right?
Best regards,
Tiago Marques
On 1/27/08, Stefan Reinauer <stepan(a)coresystems.de> wrote:
> * Tiago Marques <tiagomnm(a)gmail.com> [080127 16:21]:
> > Hi.
> > Both failed, tried with two different BIOS chips.
> > Flashing with AWDFlash works fine though.
> > Had to flash it again in a VIA K8T890 board, which works flawlessly.
> > Any ideas, fix?
>
> What's the problem?
>
> --
> coresystems GmbH • Brahmsstr. 16 • D-79104 Freiburg i. Br.
> Tel.: +49 761 7668825 • Fax: +49 761 7664613
> Email: info(a)coresystems.de • http://www.coresystems.de/
> Registergericht: Amtsgericht Freiburg • HRB 7656
> Geschäftsführer: Stefan Reinauer • Ust-IdNr.: DE245674866
>
by yannis le gal
Hi all !
I'd like to try linux bios because my laptop Medion MIM2080 have a lot of
problems :
windows freeze
i had to use noapic nolapic to install ubuntu ..
no irq assigned to the wifi (solved with a custom dsdt)
when i set video ram to 16 mo , cpu frequency change don't work
So the BIOS ,ACPI , DSDT are buggy !
Thanks for any help ;)
Yannis.
-------------------lspci-----------------------
00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:06.0 Network controller: Intel Corporation PRO/Wireless 2915ABG
Network Connection (rev 05)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II]
(rev 74)
01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome
Pro VGA Adapter (rev 02)
-------------------------------- flashrom------------------------------
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "VT8235", enabling flash write... OK.
SST49LF004A/B found at physical address 0xfff80000.
Flash part is SST49LF004A/B (512 KB).
No operations were specified.
----------- dmesg -------------------
[ 0.000000] Linux version 2.6.24-12-generic (buildd@palmer) (gcc
version 4.2.3 (Ubuntu 4.2.3-2ubuntu4)) #1 SMP Mon Mar 10 15:32:00 UTC
2008 (Ubuntu 2.6.24-12.20-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bfef000 (usable)
[ 0.000000] BIOS-e820: 000000001bff0000 - 000000001bffffc0 (ACPI data)
[ 0.000000] BIOS-e820: 000000001bffffc0 - 000000001c000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 447MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 114671) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114671
[ 0.000000] HighMem 114671 -> 114671
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114671
[ 0.000000] On node 0 totalpages: 114671
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 863 pages used for memmap
[ 0.000000] Normal zone: 109712 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00E6010 checksum 0
[ 0.000000] ACPI: RSDP 000E6010, 0014 (r0 OID_00)
[ 0.000000] ACPI: RSDT 1BFFBE80, 0030 (r1 INSYDE FACP_000 100
0000 10200)
[ 0.000000] ACPI: FACP 1BFFFB10, 0074 (r1 INSYDE FACP_000 100
0000 10200)
[ 0.000000] ACPI: DSDT 1BFFC400, 3709 (r1 INSYDE PN800 1000
INTL 2002036)
[ 0.000000] ACPI: FACS 1BFFFFC0, 0040
[ 0.000000] ACPI: APIC 1BFFFBA0, 005A (r1 INSYDE APIC_000 30303030
0000 10200)
[ 0.000000] ACPI: SSDT 1BFFBEB0, 03F2 (r1 PmRef Cpu0Ist 3000
INTL 20030522)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
1c000000:e3f80000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000
- 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000
- 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000
- 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 113776
[ 0.000000] Kernel command line:
root=UUID=f91ec9c5-e9f7-4b6b-a95b-e9a9fd7648e8 ro quiet splash locale=fr_FR
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1791.292 MHz processor.
[ 4.989980] Console: colour VGA+ 80x25
[ 4.989986] console [tty0] enabled
[ 4.990281] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 4.990564] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 5.003212] Memory: 442772k/458684k available (2164k kernel code,
15340k reserved, 1007k data, 364k init, 0k highmem)
[ 5.003221] virtual kernel memory layout:
[ 5.003222] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 5.003223] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 5.003225] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 5.003226] lowmem : 0xc0000000 - 0xdbfef000 ( 447 MB)
[ 5.003227] .init : 0xc041f000 - 0xc047a000 ( 364 kB)
[ 5.003228] .data : 0xc031d1bd - 0xc0418dc4 (1007 kB)
[ 5.003229] .text : 0xc0100000 - 0xc031d1bd (2164 kB)
[ 5.003233] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 5.003283] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=1, Nodes=1
[ 5.083223] Calibrating delay using timer specific routine.. 3586.88
BogoMIPS (lpj=7173776)
[ 5.083259] Security Framework initialized
[ 5.083271] SELinux: Disabled at boot.
[ 5.083290] AppArmor: AppArmor initialized
[ 5.083295] Failure registering capabilities with primary security
module.
[ 5.083304] Mount-cache hash table entries: 512
[ 5.083470] CPU: After generic identify, caps: afe9fbbf 00000000
00000000 00000000 00000180 00000000 00000000 00000000
[ 5.083486] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 5.083489] CPU: L2 cache: 2048K
[ 5.083493] CPU: After all inits, caps: afe9fbbf 00000000 00000000
00002040 00000180 00000000 00000000 00000000
[ 5.083502] Compat vDSO mapped to ffffe000.
[ 5.083518] Checking 'hlt' instruction... OK.
[ 5.099679] SMP alternatives: switching to UP code
[ 5.101757] Freeing SMP alternatives: 11k freed
[ 5.101877] Early unpacking initramfs... done
[ 5.439518] ACPI: Core revision 20070126
[ 5.439593] ACPI: Looking for DSDT in initramfs... successfully read
12498 bytes from /DSDT.aml.
[ 5.439631] ACPI: Table DSDT replaced by host OS
[ 5.439635] ACPI: DSDT 00000000, 30D2 (r1 INSYDE PN800 1000
INTL 20061109)
[ 5.439640] ACPI: DSDT override uses original SSDTs unless
"acpi_no_auto_ssdt"CPU0: Intel(R) Pentium(R) M processor 1.80GHz stepping 06
[ 5.451523] Total of 1 processors activated (3586.88 BogoMIPS).
[ 5.452235] ENABLING IO-APIC IRQs
[ 5.452561] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 5.598699] Brought up 1 CPUs
[ 5.598758] CPU0 attaching sched-domain:
[ 5.598761] domain 0: span 01
[ 5.598763] groups: 01
[ 5.598947] net_namespace: 64 bytes
[ 5.598957] Booting paravirtualized kernel on bare hardware
[ 5.599442] Time: 12:25:04 Date: 03/11/08
[ 5.599497] NET: Registered protocol family 16
[ 5.599690] EISA bus registered
[ 5.599722] ACPI: bus type pci registered
[ 5.599877] PCI: PCI BIOS revision 2.10 entry at 0xe9c04, last bus=1
[ 5.599879] PCI: Using configuration type 1
[ 5.599881] Setting up standard PCI resources
[ 5.601871] ACPI: EC: Look up EC in DSDT
[ 5.604517] ACPI: Interpreter enabled
[ 5.604521] ACPI: (supports S0 S1 S3 S4 S5)
[ 5.604538] ACPI: Using IOAPIC for interrupt routing
[ 5.606124] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 5.613887] ACPI: EC: GPE = 0x1, I/O: command/status = 0x66, data = 0x62
[ 5.613890] ACPI: EC: driver started in interrupt mode
[ 5.613927] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 5.614674] PCI quirk: region 1000-107f claimed by vt8235 PM
[ 5.614678] PCI quirk: region 1400-140f claimed by vt8235 SMB
[ 5.615088] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 5.625395] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 5.625476] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *7 10 11 14 15)
[ 5.625554] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 5.625631] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 14 15)
[ 5.625702] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[ 5.625774] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[ 5.625845] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[ 5.625916] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[ 5.626012] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
[ 5.626108] ACPI: PCI Interrupt Link [ALKB] (IRQs 23) *11
[ 5.626238] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *5, disabled.
[ 5.626318] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *0
[ 5.626406] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 5.626434] pnp: PnP ACPI init
[ 5.626441] ACPI: bus type pnp registered
[ 5.630514] pnp: PnP ACPI: found 9 devices
[ 5.630517] ACPI: ACPI bus type pnp unregistered
[ 5.630521] PnPBIOS: Disabled by ACPI PNP
[ 5.630723] PCI: Using ACPI for IRQ routing
[ 5.630726] PCI: If a device doesn't work, try "pci=routeirq". If it
helps, post a report
[ 5.642622] NET: Registered protocol family 8
[ 5.642625] NET: Registered protocol family 20
[ 5.642684] AppArmor: AppArmor Filesystem Enabled
[ 5.646599] Time: tsc clocksource has been installed.
[ 5.654625] system 00:05: iomem range 0xe0000-0xfffff could not be
reserved
[ 5.654628] system 00:05: iomem range 0xfff80000-0xffffffff could not
be reserved
[ 5.654631] system 00:05: iomem range 0xfec00000-0xfec00fff has been
reserved
[ 5.654634] system 00:05: iomem range 0xfee00000-0xfee00fff has been
reserved
[ 5.654640] system 00:07: ioport range 0x330-0x331 has been reserved
[ 5.654642] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 5.654645] system 00:07: ioport range 0x1000-0x107f has been reserved
[ 5.654648] system 00:07: ioport range 0x1400-0x140f has been reserved
[ 5.684999] PCI: Bridge: 0000:00:01.0
[ 5.685002] IO window: c000-dfff
[ 5.685007] MEM window: c0000000-cfffffff
[ 5.685011] PREFETCH window: 90000000-9fffffff
[ 5.685033] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 5.685044] NET: Registered protocol family 2
[ 5.722578] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 5.722762] TCP established hash table entries: 16384 (order: 5,
131072 bytes)
[ 5.722881] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 5.723013] TCP: Hash tables configured (established 16384 bind 16384)
[ 5.723016] TCP reno registered
[ 5.734613] checking if image is initramfs... it is
[ 6.186000] Switched to high resolution mode on CPU 0
[ 6.394689] Freeing initrd memory: 7228k freed
[ 6.395464] audit: initializing netlink socket (disabled)
[ 6.395488] audit(1205238304.280:1): initialized
[ 6.397619] VFS: Disk quotas dquot_6.5.1
[ 6.397727] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 6.397906] io scheduler noop registered
[ 6.397909] io scheduler anticipatory registered
[ 6.397911] io scheduler deadline registered
[ 6.397924] io scheduler cfq registered (default)
[ 6.397944] PCI: VIA PCI bridge detected. Disabling DAC.
[ 6.398002] Boot video device is 0000:01:00.0
[ 6.398302] isapnp: Scanning for PnP cards...
[ 6.752300] isapnp: No Plug & Play device found
[ 6.778646] Real Time Clock Driver v1.12ac
[ 6.778773] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 6.779959] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 6.780033] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 6.780130] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 6.791874] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 6.797559] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 6.797564] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 6.797566] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 6.797569] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 6.797571] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 6.809263] mice: PS/2 mouse device common for all mice
[ 6.809372] EISA: Probing bus 0 at eisa.0
[ 6.809380] Cannot allocate resource for EISA slot 1
[ 6.809411] EISA: Detected 0 cards.
[ 6.809415] cpuidle: using governor ladder
[ 6.809417] cpuidle: using governor menu
[ 6.809528] NET: Registered protocol family 1
[ 6.809561] Using IPI No-Shortcut mode
[ 6.809602] registered taskstats version 1
[ 6.809708] Magic number: 0:453:430
[ 6.809858] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 6.809869] EDD information not available.
[ 6.810139] Freeing unused kernel memory: 364k freed
[ 6.829207] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
[ 8.004266] fuse init (API version 7.9)
[ 8.015555] allocation failed: out of vmalloc space - use
vmalloc=<size> to increase size.
[ 8.015562] ACPI Error (psparse-0537): Method parse/execution failed
[\_PR_.CPU0._PDC] (Node d9c9a7c8), AE_NO_MEMORY
[ 8.015806] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 8.015811] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 8.645709] usbcore: registered new interface driver usbfs
[ 8.645738] usbcore: registered new interface driver hub
[ 8.663024] usbcore: registered new device driver usb
[ 8.701068] SCSI subsystem initialized
[ 8.706949] USB Universal Host Controller Interface driver v3.0
[ 8.707172] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0,
using IRQ 21
[ 8.707176] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 21
[ 8.707185] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKD] -> GSI
21 (level, low) -> IRQ 16
[ 8.707199] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 8.707760] uhci_hcd 0000:00:10.0: new USB bus registered, assigned
bus number 1
[ 8.707795] uhci_hcd 0000:00:10.0: irq 16, io base 0x00001200
[ 8.707936] usb usb1: configuration #1 chosen from 1 choice
[ 8.707963] hub 1-0:1.0: USB hub found
[ 8.707968] hub 1-0:1.0: 2 ports detected
[ 8.773177] libata version 3.00 loaded.
[ 8.782861] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 8.811049] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKD] -> GSI
21 (level, low) -> IRQ 16
[ 8.811065] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 8.811093] uhci_hcd 0000:00:10.1: new USB bus registered, assigned
bus number 2
[ 8.811119] uhci_hcd 0000:00:10.1: irq 16, io base 0x00001220
[ 8.811233] usb usb2: configuration #1 chosen from 1 choice
[ 8.811256] hub 2-0:1.0: USB hub found
[ 8.811262] hub 2-0:1.0: 2 ports detected
[ 8.914823] ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKD] -> GSI
21 (level, low) -> IRQ 16
[ 8.914839] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 8.914865] uhci_hcd 0000:00:10.2: new USB bus registered, assigned
bus number 3
[ 8.914891] uhci_hcd 0000:00:10.2: irq 16, io base 0x00001240
[ 8.915000] usb usb3: configuration #1 chosen from 1 choice
[ 8.915024] hub 3-0:1.0: USB hub found
[ 8.915030] hub 3-0:1.0: 2 ports detected
[ 9.018793] PCI: Enabling device 0000:00:10.3 (0000 -> 0002)
[ 9.018806] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKD] -> GSI
21 (level, low) -> IRQ 16
[ 9.018825] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 9.018852] ehci_hcd 0000:00:10.3: new USB bus registered, assigned
bus number 4
[ 9.018898] ehci_hcd 0000:00:10.3: irq 16, io mem 0x20001000
[ 9.030534] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 9.030666] usb usb4: configuration #1 chosen from 1 choice
[ 9.030691] hub 4-0:1.0: USB hub found
[ 9.030698] hub 4-0:1.0: 6 ports detected
[ 9.134904] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 11,
using IRQ 23
[ 9.134909] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 23
[ 9.134918] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKB] -> GSI
23 (level, low) -> IRQ 17
[ 9.139237] eth0: VIA Rhine II at 0xd0000000, 00:40:d0:71:68:85, IRQ 17.
[ 9.139951] eth0: MII PHY found at address 1, status 0x7849
advertising 05e1 Link 0000.
[ 9.140208] ACPI: PCI Interrupt Link [ALKA] disabled and referenced,
BIOS bug
[ 9.140248] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0,
using IRQ 20
[ 9.140250] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 9.140254] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI
20 (level, low) -> IRQ 18
[ 9.140306] ACPI: PCI interrupt for device 0000:00:11.1 disabled
[ 9.153717] pata_via 0000:00:11.1: version 0.3.3
[ 9.153743] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI
20 (level, low) -> IRQ 18
[ 9.155028] scsi0 : pata_via
[ 9.155369] scsi1 : pata_via
[ 9.157144] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100
irq 14
[ 9.157148] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108
irq 15
[ 9.822092] ata1.00: ATA-7: SAMSUNG MP0402H, UC100-14, max UDMA/100
[ 9.822096] ata1.00: 78242976 sectors, multi 16: LBA48
[ 9.829926] ata1.00: configured for UDMA/100
[ 9.996783] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MP0402H
UC10 PQ: 0 ANSI: 5
[ 10.002729] usb 2-2: new low speed USB device using uhci_hcd and
address 2
[ 10.003182] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 10.003186] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 10.011108] Driver 'sd' needs updating - please use bus_type methods
[ 10.011203] sd 0:0:0:0: [sda] 78242976 512-byte hardware sectors
(40060 MB)
[ 10.011217] sd 0:0:0:0: [sda] Write Protect is off
[ 10.011220] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 10.011234] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 10.011285] sd 0:0:0:0: [sda] 78242976 512-byte hardware sectors
(40060 MB)
[ 10.011294] sd 0:0:0:0: [sda] Write Protect is off
[ 10.011296] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 10.011311] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 10.011314] sda: sda1 sda2 < sda5 >
[ 10.046157] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.052449] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 10.172407] usb 2-2: configuration #1 chosen from 1 choice
[ 10.189559] usbcore: registered new interface driver hiddev
[ 10.202551] input: PS/2+USB Mouse as
/devices/pci0000:00/0000:00:10.1/usb2/2-2/2-2:1.0/input/input2
[ 10.213273] input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on
usb-0000:00:10.1-2
[ 10.213285] usbcore: registered new interface driver usbhid
[ 10.213288] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c:
v2.6:USB HID core driver
[ 10.242830] Attempting manual resume
[ 10.242835] swsusp: Resume From Partition 8:5
[ 10.242836] PM: Checking swsusp image.
[ 10.243018] PM: Resume from disk failed.
[ 10.291962] kjournald starting. Commit interval 5 seconds
[ 10.291973] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.736498] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.797443] nf_conntrack version 0.5.0 (7168 buckets, 28672 max)
[ 20.664586] Linux agpgart interface v0.102
[ 20.716138] agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
[ 20.725720] agpgart: AGP aperture is 128M @ 0xa0000000
[ 21.092078] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 21.144086] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 21.200090] input: Power Button (FF) as /devices/virtual/input/input3
[ 21.211884] ACPI: Power Button (FF) [PWRF]
[ 21.211972] input: Lid Switch as /devices/virtual/input/input4
[ 21.215125] ACPI: Lid Switch [LID]
[ 21.215187] input: Sleep Button (CM) as /devices/virtual/input/input5
[ 21.227854] ACPI: Sleep Button (CM) [SBTN]
[ 21.227948] input: Power Button (CM) as /devices/virtual/input/input6
[ 21.239835] ACPI: Power Button (CM) [PBTN]
[ 21.266399] ACPI: AC Adapter [AC] (on-line)
[ 21.331804] ACPI: Battery Slot [BAT0] (battery absent)
[ 21.603431] ieee80211_crypt: registered algorithm 'NULL'
[ 21.659368] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 21.659372] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno(a)linux.intel.com>
[ 21.764818] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
1.2.2kmprq
[ 21.764824] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 21.764942] PCI: Enabling device 0000:00:06.0 (0000 -> 0002)
[ 21.764955] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level,
low) -> IRQ 19
[ 21.764966] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 21.807168] ipw2200: Detected Intel PRO/Wireless 2915ABG Network
Connection
[ 22.527416] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/LNXVIDEO:00/input/input7
[ 22.538283] ACPI: Video Device [VGA0] (multi-head: yes rom: no
post: no)
[ 23.037073] snd: no version for "unregister_sound_special" found:
kernel tainted.
[ 24.024943] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 24.689931] Synaptics Touchpad, model: 1, fw: 5.9, id: 0xa56eb1,
caps: 0x804713/0x0
[ 24.740020] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio3/input/input9
[ 25.498523] ipw2200: Detected geography ZZH (13 802.11bg channels, 4
802.11a channels)
[ 25.502860] ACPI: PCI Interrupt Link [ALKC] disabled and referenced,
BIOS bug
[ 25.502973] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 5,
using IRQ 22
[ 25.502976] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 25.502985] ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [ALKC] -> GSI
22 (level, low) -> IRQ 20
[ 25.510298] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 25.585193] irda_init()
[ 25.585217] NET: Registered protocol family 23
[ 26.015022] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI
22 (level, low) -> IRQ 20
[ 26.015164] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 27.439990] lp: driver loaded but no devices found
[ 27.640481] Adding 1461872k swap on /dev/sda5. Priority:-1 extents:1
across:1461872k
[ 28.272783] EXT3 FS on sda1, internal journal
[ 31.522299] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 31.557367] No dock devices found.
[ 32.846071] ppdev: user-space parallel port driver
[ 33.398077] audit(1205238332.106:2): operation="inode_permission"
request_mask="a::" denied_mask="a::" name="/dev/tty" pid=4851
profile="/usr/sbin/cupsd" namespace="default"
[ 33.526673] apm: BIOS not found.
[ 75.873743] Marking TSC unstable due to: cpufreq changes.
[ 75.882691] Time: acpi_pm clocksource has been installed.
[ 39.250591] eth0: link down
[ 39.311696] Bluetooth: Core ver 2.11
[ 39.312234] NET: Registered protocol family 31
[ 39.312236] Bluetooth: HCI device and connection manager initialized
[ 39.312241] Bluetooth: HCI socket layer initialized
[ 62.910349] Bluetooth: L2CAP ver 2.9
[ 62.910357] Bluetooth: L2CAP socket layer initialized
[ 63.235895] Bluetooth: RFCOMM socket layer initialized
[ 63.235926] Bluetooth: RFCOMM TTY layer initialized
[ 63.235930] Bluetooth: RFCOMM ver 1.8
[ 38.500755] [drm] Initialized drm 1.1.0 20060810
[ 117.339835] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level,
low) -> IRQ 21
[ 117.343580] [drm] Initialized via 2.11.1 20070202 on minor 0
[ 117.521033] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 117.521102] agpgart: Device is in legacy mode, falling back to 2.x
[ 117.521123] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 117.521342] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 301.592332] NET: Registered protocol family 10
[ 301.593158] lo: Disabled Privacy Extensions
[ 301.594638] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 301.595291] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 356.960096] NET: Registered protocol family 17
[ 358.419283] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 361.246183] ieee80211_crypt: registered algorithm 'TKIP'
