Add support for the LiPPERT Cool SpaceRunner-LX embedded PC board:
- PC/104+ form factor
- AMD Geode-LX CPU/northbridge
- AMD CS5536 southbridge
- ITE IT8712F superio
Signed-off-by: Jens Rottmann <JRottmann(a)LiPPERTEmbedded.de>
---
My previous mail still awaits list moderator approval, but I'm sending
this anyway. :) Maybe you'll have to apply the patches from my previous
mail first for this to compile.
There are still large parts of coreboot's design that I don't fully
understand yet, but I hope I did all right. All mainboard files are
based on the AMD DB800.
By the way, cmos.layout doesn't seem to be used (HAVE_OPTION_TABLE=0),
still coreboot doesn't compile without it. Is there a designated way to
use a global, generic file instead?
Best regards,
Jens Rottmann
Index: src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c
===================================================================
--- src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c (working copy)
@@ -0,0 +1,213 @@
+/*
+ * (C)2008 LiPPERT Embedded Computers GmbH, released under the GNU GPLv2
+ *
+ * Based on cache_as_ram_auto.c from AMD's DB800 and DBM690T mainboards.
+ */
+
+#define ASSEMBLY 1
+
+#include <stdlib.h>
+#include <stdint.h>
+#include <spd.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "cpu/x86/bist.h"
+#include "cpu/x86/msr.h"
+#include <cpu/amd/lxdef.h>
+#include <cpu/amd/geode_post_code.h>
+#include "southbridge/amd/cs5536/cs5536.h"
+
+#define POST_CODE(x) outb(x, 0x80)
+
+#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
+#include "southbridge/amd/cs5536/cs5536_early_setup.c"
+#include "superio/ite/it8712f/it8712f_early_serial.c"
+
+#define SMC_CONFIG 0x01 /* bit0 enables Spread Spectrum, bit1 makes on-board SSD act as IDE Slave */
+
+#define ManualConf 1 /* No automatic strapped PLL config */
+#define PLLMSRhi 0x0000059C /* Manual settings for the PLL */
+#define PLLMSRlo 0x00DE6001
+#define DIMM0 0xA0
+#define DIMM1 0xA2
+
+static const unsigned char spdbytes[] = { // 4x Promos V58C2512164SA-J5I
+ 0xFF, 0xFF, // only values used by Geode-LX raminit.c are set
+ [SPD_MEMORY_TYPE] = SPD_MEMORY_TYPE_SDRAM_DDR, // (Fundamental) memory type
+ [SPD_NUM_ROWS] = 0x0D, // Number of row address bits [13]
+ [SPD_NUM_COLUMNS] = 0x0A, // Number of column address bits [10]
+ [SPD_NUM_DIMM_BANKS] = 1, // Number of module rows (banks)
+ 0xFF, 0xFF, 0xFF,
+ [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 0x50, // SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD]
+ 0xFF, 0xFF,
+ [SPD_REFRESH] = 0x82, // Refresh rate/type [Self Refresh, 7.8 us]
+ [SPD_PRIMARY_SDRAM_WIDTH] = 64, // SDRAM width (primary SDRAM) [64 bits]
+ 0xFF, 0xFF, 0xFF,
+ [SPD_NUM_BANKS_PER_SDRAM] = 4, // SDRAM device attributes, number of banks on SDRAM device
+ [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x1C, // SDRAM device attributes, CAS latency [3, 2.5, 2]
+ 0xFF, 0xFF,
+ [SPD_MODULE_ATTRIBUTES] = 0x20, // SDRAM module attributes [differential clk]
+ [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0x40, // SDRAM device attributes, general [Concurrent AP]
+ [SPD_SDRAM_CYCLE_TIME_2ND] = 0x60, // SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD]
+ 0xFF,
+ [SPD_SDRAM_CYCLE_TIME_3RD] = 0x75, // SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD]
+ 0xFF,
+ [SPD_tRP] = 60, // Min. row precharge time [15 ns in units of 0.25 ns]
+ [SPD_tRRD] = 40, // Min. row active to row active [10 ns in units of 0.25 ns]
+ [SPD_tRCD] = 60, // Min. RAS to CAS delay [15 ns in units of 0.25 ns]
+ [SPD_tRAS] = 40, // Min. RAS pulse width = active to precharge delay [40 ns]
+ [SPD_BANK_DENSITY] = 0x40, // Density of each row on module [256 MB]
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ [SPD_tRFC] = 70 // SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns]
+};
+
+static inline int spd_read_byte(unsigned int device, unsigned int address)
+{
+ if (device != DIMM0) return 0xFF; // no DIMM1, don't even try
+#if DEBUG
+ if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) {
+ print_err("ERROR: spd_read_byte(DIMM0, 0x");
+ print_err_hex8(address);
+ print_err(") returns 0xff\r\n");
+ }
+#endif
+ return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF; // fake SPD ROM value
+}
+
+/* Send config data to System Management Controller via SMB. */
+static int smc_send_config(unsigned char config_data)
+{
+ if (smbus_check_stop_condition(SMBUS_IO_BASE))
+ return 1;
+ if (smbus_start_condition(SMBUS_IO_BASE))
+ return 2;
+ if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address
+ return 3;
+ if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data
+ return 4;
+ if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length
+ return 5;
+ if (smbus_send_command(SMBUS_IO_BASE, config_data))
+ return 6;
+ smbus_stop_condition(SMBUS_IO_BASE);
+ return 0;
+}
+
+#include "northbridge/amd/lx/raminit.h"
+#include "northbridge/amd/lx/pll_reset.c"
+#include "northbridge/amd/lx/raminit.c"
+#include "sdram/generic_sdram.c"
+#include "cpu/amd/model_lx/cpureginit.c"
+#include "cpu/amd/model_lx/syspreinit.c"
+
+static void msr_init(void)
+{
+ msr_t msr;
+
+ /* Setup access to the cache for under 1MB. */
+ msr.hi = 0x24fffc02;
+ msr.lo = 0x1000A000; /* 0-A0000 write back */
+ wrmsr(CPU_RCONF_DEFAULT, msr);
+
+ msr.hi = 0x0; /* Write back */
+ msr.lo = 0x0;
+ wrmsr(CPU_RCONF_A0_BF, msr);
+ wrmsr(CPU_RCONF_C0_DF, msr);
+ wrmsr(CPU_RCONF_E0_FF, msr);
+
+ /* Setup access to the cache for under 640K. Note MC not setup yet. */
+ msr.hi = 0x20000000;
+ msr.lo = 0xfff80;
+ wrmsr(MSR_GLIU0 + 0x20, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0x80fffe0;
+ wrmsr(MSR_GLIU0 + 0x21, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0xfff80;
+ wrmsr(MSR_GLIU1 + 0x20, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0x80fffe0;
+ wrmsr(MSR_GLIU1 + 0x21, msr);
+}
+
+static const unsigned short sio_init_table[] = { // hi=data, lo=index
+ 0x0707, // select LDN 7 (GPIO, SPI, watchdog, ...)
+ 0x1E2C, // disable ATXPowerGood
+ 0x0423, // don't delay POWerOK1/2
+ 0x9072, // watchdog triggers POWOK, counts seconds
+#if !USE_WATCHDOG_ON_BOOT
+ 0x0073, 0x0074, // disable watchdog by setting timeout to 0
+#endif
+ 0xBF25, 0x172A, 0xF326, // select GPIO function for most pins
+ 0xFF27, 0xDF28, 0x2729, // (GP45=SUSB, GP23,22,16,15=SPI, GP13=PWROK1)
+ 0x072C, // VIN6=enabled?, FAN4/5 disabled, VIN7=internal, VIN3=internal
+ 0x66B8, 0x0CB9, // enable pullups
+ 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED
+ 0x07C8, // config GP12-10 as output
+ 0x2DF5, // map Hw Monitor Thermal Output to GP55
+ 0x08F8, // map GP LED Blinking 1 to GP10=LIVE_LED (deactivate Simple I/O to use)
+ 0x0202 // exit conf mode
+};
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+ int i;
+
+ /* Init SuperIO WDT, GPIOs. Done early, WDT init may trigger reset! */
+ it8712f_enter_conf();
+ for (i=0; i<ARRAY_SIZE(sio_init_table); i++) {
+ unsigned short val = sio_init_table[i];
+ outb((unsigned char)val, SIO_INDEX); outb(val>>8, SIO_DATA);
+ }
+ //it8712f_exit_conf() is included in sio_init_table
+}
+
+void cache_as_ram_main(void)
+{
+ int err;
+ POST_CODE(0x01);
+
+ static const struct mem_controller memctrl[] = {
+ {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}}
+ };
+
+ SystemPreInit();
+ msr_init();
+
+ cs5536_early_setup();
+
+ /* Note: must do this AFTER the early_setup! It is counting on some
+ * early MSR setup for CS5536.
+ */
+ it8712f_enable_serial(0, TTYS0_BASE); // does not use its 1st parameter
+ mb_gpio_init();
+ uart_init();
+ console_init();
+
+ pll_reset(ManualConf);
+
+ cpuRegInit();
+
+ if ((err=smc_send_config(SMC_CONFIG))) { // bit1=on-board IDE is Slave, bit0=Spread Spectrum
+ print_err("ERROR ");
+ print_err_char('0'+err);
+ print_err(" sending config data to SMC\r\n");
+ }
+
+ sdram_initialize(1, memctrl);
+
+ /* Check memory. */
+ /* ram_check(0x00000000, 640 * 1024); */
+
+ /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
+ return;
+}
Index: src/mainboard/lippert/spacerunner-lx/chip.h
===================================================================
--- src/mainboard/lippert/spacerunner-lx/chip.h (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/chip.h (working copy)
@@ -0,0 +1,11 @@
+/*
+ * (C)2008 LiPPERT Embedded Computers GmbH, released under the GNU GPLv2
+ *
+ * Based on chip.h from AMD's DB800 mainboard.
+ */
+
+extern struct chip_operations mainboard_lippert_spacerunner_lx_ops;
+
+struct mainboard_lippert_spacerunner_lx_config {
+ unsigned char sio_gp1x_config; // bit2=RS485_EN2, bit1=RS485_EN1, bit0=Live LED
+};
Index: src/mainboard/lippert/spacerunner-lx/cmos.layout
===================================================================
--- src/mainboard/lippert/spacerunner-lx/cmos.layout (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/cmos.layout (working copy)
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+1008 16 h 0 check_sum
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+
+checksums
+
+checksum 392 1007 1008
+
+
Index: src/mainboard/lippert/spacerunner-lx/Config.lb
===================================================================
--- src/mainboard/lippert/spacerunner-lx/Config.lb (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/Config.lb (working copy)
@@ -0,0 +1,213 @@
+##
+## Compute the location and size of where this firmware image
+## (coreboot plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+ default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE )
+ default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The coreboot bootloader.
+##
+
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of coreboot will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up coreboot,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+if HAVE_PIRQ_TABLE
+ object irq_tables.o
+end
+
+if USE_DCACHE_RAM
+ #compile cache_as_ram.c to auto.inc
+ makerule ./cache_as_ram_auto.inc
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
+ action "perl -e 's/.rodata/.rom.data/g' -pi $@"
+ action "perl -e 's/.text/.section .rom.text/g' -pi $@"
+ end
+end
+
+
+##
+## Build our 16 bit and 32 bit coreboot entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where coreboot is entered)
+##
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+end
+
+### Should this be in the northbridge code?
+#not in serengeti_cheetah mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of coreboot startup
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+ ldscript /arch/i386/lib/failover.lds
+# mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+
+if USE_DCACHE_RAM
+ mainboardinit cpu/amd/model_lx/cache_as_ram.inc
+ mainboardinit ./cache_as_ram_auto.inc
+end
+
+##
+## Include the secondary Configuration files
+##
+dir /pc80
+config chip.h
+# see also SMC_CONFIG in cache_as_ram_auto.c
+register "sio_gp1x_config" = "0x01" # bit0 turns off Live LED, bit1 switches Com1 to RS485, bit2 same for Com2
+
+chip northbridge/amd/lx
+ device pci_domain 0 on
+ device pci 1.0 on end # Northbridge
+ device pci 1.1 on end # Graphics
+ device pci 1.2 on end # AES
+ chip southbridge/amd/cs5536
+ # IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK
+ # SIRQ Mode = Active(Quiet) mode. Save power....
+ # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse, UARTs, etc IRQs. OK
+ register "lpc_serirq_enable" = "0x000012DA" # 00010010 11011010
+ register "lpc_serirq_polarity" = "0x0000ED25" # inverse of above
+ register "lpc_serirq_mode" = "1"
+ register "enable_gpio_int_route" = "0x0D0C0700"
+ register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
+ register "enable_USBP4_device" = "0" # 0: host, 1:device
+ register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
+ register "com1_enable" = "0"
+ register "com1_address" = "0x3E8"
+ register "com1_irq" = "6"
+ register "com2_enable" = "0"
+ register "com2_address" = "0x2E8"
+ register "com2_irq" = "6"
+ register "unwanted_vpci[0]" = "0x80007B00" # Audio: 1<<31 + Device 0x0F<<11 + Function 3<<8
+ register "unwanted_vpci[1]" = "0" # End of list has a zero
+ device pci 8.0 on end # Slot4
+ device pci 9.0 on end # Slot3
+ device pci a.0 on end # Slot2
+ device pci b.0 on end # Slot1
+ device pci c.0 on end # IT8888
+ device pci e.0 on end # Ethernet
+ device pci f.0 on # ISA Bridge
+ chip superio/ite/it8712f
+ device pnp 2e.0 off # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.1 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.2 on # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.3 on # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 2e.4 on # EC
+ io 0x60 = 0x290
+ io 0x62 = 0x230
+ irq 0x70 = 9
+ end
+ device pnp 2e.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ end
+ device pnp 2e.6 on # Mouse
+ irq 0x70 = 12
+ end
+ device pnp 2e.7 on # GPIO
+ io 0x62 = 0x1220
+ io 0x64 = 0x1200
+ end
+ device pnp 2e.8 off # MIDI
+ io 0x60 = 0x300
+ irq 0x70 = 9
+ end
+ device pnp 2e.9 off # GAME
+ io 0x60 = 0x220
+ end
+ device pnp 2e.a off end # CIR
+ end
+ end
+ device pci f.2 on end # IDE Controller
+ device pci f.3 off end # Audio
+ device pci f.4 on end # OHCI
+ device pci f.5 on end # EHCI
+ end
+ end
+ # APIC cluster is late CPU init.
+ device apic_cluster 0 on
+ chip cpu/amd/model_lx
+ device apic 0 on end
+ end
+ end
+end
+
Index: src/mainboard/lippert/spacerunner-lx/irq_tables.c
===================================================================
--- src/mainboard/lippert/spacerunner-lx/irq_tables.c (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/irq_tables.c (working copy)
@@ -0,0 +1,59 @@
+/*
+ * (C)2008 LiPPERT Embedded Computers GmbH, released under the GNU GPLv2
+ *
+ * Based on irq_tables.c from AMD's DB800 mainboard.
+ */
+
+#include <arch/pirq_routing.h>
+#include <console/console.h>
+#include <arch/io.h>
+#include <arch/pirq_routing.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
+
+/* Platform IRQs */
+#define PIRQA 10
+#define PIRQB 11
+#define PIRQC 5
+#define PIRQD 15
+
+/* Map */
+#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */
+#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */
+#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */
+#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */
+
+/* Link */
+#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */
+#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */
+#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */
+#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
+ 0x00, /* IRQs devoted exclusively to PCI usage */
+ 0x100B, /* Vendor */
+ 0x002B, /* Device */
+ 0, /* Crap (miniport) */
+ {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
+ 0xE0, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
+ {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
+ {0x00, (0x0E << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */
+ {0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0}, /* slot1 */
+ {0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0}, /* slot2 */
+ {0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0}, /* slot3 */
+ {0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0}, /* slot4 */
+ }
+};
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
Index: src/mainboard/lippert/spacerunner-lx/mainboard.c
===================================================================
--- src/mainboard/lippert/spacerunner-lx/mainboard.c (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/mainboard.c (working copy)
@@ -0,0 +1,61 @@
+/*
+ * (C)2008 LiPPERT Embedded Computers GmbH, released under the GNU GPLv2
+ *
+ * Based on mainboard.c from AMD's DB800 mainboard.
+ */
+
+#include <stdlib.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <arch/io.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "chip.h"
+
+static const unsigned short ec_init_table[] = { // hi=data, lo=index
+ 0x1900, // enable monitoring
+ 0x3050, // VIN4,5 enabled
+ 0x0351, // TMPIN1,2 diode mode, TMPIN3 off
+ 0x805C, // unlock zero adjust
+ 0x7056, 0x3C57, // zero adjust TMPIN1,2
+ 0x005C, // lock zero adjust
+ 0xD014 // also set FAN_CTL polarity to Active High
+};
+
+static void init(struct device *dev)
+{
+ struct mainboard_lippert_spacerunner_lx_config *mb = dev->chip_info;
+ unsigned int gpio_base, i;
+ printk_debug("LiPPERT SpaceRunner-LX ENTER %s\n", __FUNCTION__);
+
+ /* Init CS5536 GPIOs */
+ gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, 0),
+ PCI_BASE_ADDRESS_1) - 1;
+ outl(0x00000040, gpio_base + 0x00); // GPIO6 value 1 - LAN_PD#
+ outl(0x00000040, gpio_base + 0x04); // GPIO6 output 1 - LAN_PD#
+ outl(0x04000000, gpio_base + 0x18); // GPIO10 pull up 0 - THRM_ALRM#
+ outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1 1 - THRM_ALRM#
+ outl(0x00000400, gpio_base + 0x20); // GPIO10 input 1 - THRM_ALRM#
+ outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2 1 - 32kHz
+ outl(0x00000800, gpio_base + 0x84); // GPIO27 output 1 - 32kHz
+ outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz
+
+ /* Init Environment Controller */
+ for (i=0; i<ARRAY_SIZE(ec_init_table); i++) {
+ unsigned short val = ec_init_table[i];
+ outb((unsigned char)val, 0x0295); outb(val>>8, 0x0296);
+ }
+
+ outb(mb->sio_gp1x_config, 0x1220); // Simple-I/O GP17-10
+ printk_debug("LiPPERT SpaceRunner-LX EXIT %s\n", __FUNCTION__);
+}
+
+static void enable_dev(struct device *dev)
+{
+ dev->ops->init = init;
+}
+
+struct chip_operations mainboard_lippert_spacerunner_lx_ops = {
+ CHIP_NAME("LiPPERT SpaceRunner-LX Mainboard")
+ .enable_dev = enable_dev,
+};
Index: src/mainboard/lippert/spacerunner-lx/Options.lb
===================================================================
--- src/mainboard/lippert/spacerunner-lx/Options.lb (revision 0)
+++ src/mainboard/lippert/spacerunner-lx/Options.lb (working copy)
@@ -0,0 +1,190 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_IDE
+uses CONFIG_FS_PAYLOAD
+uses CONFIG_FS_EXT2
+uses AUTOBOOT_DELAY
+uses AUTOBOOT_CMDLINE
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses COREBOOT_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESS
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEBUG
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses CONFIG_VIDEO_MB
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
+uses PIRQ_ROUTE
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE = 512*1024
+
+###
+### Build options
+###
+default CONFIG_CONSOLE_VGA=0
+default CONFIG_VIDEO_MB=8
+default CONFIG_PCI_ROM_RUN=0
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from coreboot
+##
+default HAVE_HARD_RESET=0
+
+## Delay timer options
+##
+default CONFIG_UDELAY_TSC=1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=7
+default PIRQ_ROUTE=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### coreboot layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xc8000
+default DCACHE_RAM_SIZE=0x08000
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_PAYLOAD = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+# Compile extra debugging code
+default DEBUG=1
+
+##
+### Select the coreboot loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+end
+
Index: targets/lippert/spacerunner-lx/Config.lb
===================================================================
--- targets/lippert/spacerunner-lx/Config.lb (revision 0)
+++ targets/lippert/spacerunner-lx/Config.lb (working copy)
@@ -0,0 +1,45 @@
+##
+## (C)2008 LiPPERT Embedded Computers GmbH, released under the GNU GPLv2
+##
+
+# Config file for the LiPPERT Cool SpaceRunner-LX, --JR 10/2008
+# based on Config.lb for the AMD Geode LX/5536 DB800 platform.
+
+target spacerunner-lx
+mainboard lippert/spacerunner-lx
+
+# HACK to get the right TSC support.
+option CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
+option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
+
+## Load payload (e.g. Linux) from IDE
+#option CONFIG_ROM_PAYLOAD=0
+#option CONFIG_IDE=1
+#option CONFIG_FS_PAYLOAD=1
+#option CONFIG_FS_EXT2=1
+#option AUTOBOOT_DELAY=0
+#option AUTOBOOT_CMDLINE="hda1:/payload.elf"
+
+# Leave 36k for VSA. Board is equipped with a 1 MB SPI flash, however, due to
+# limitations of the IT8712F SIO, only the top 512 KB are directly mapped.
+option ROM_SIZE=512*1024-36*1024
+option FALLBACK_SIZE=ROM_SIZE
+
+#option DEFAULT_CONSOLE_LOGLEVEL = 4
+#option MAXIMUM_CONSOLE_LOGLEVEL = 4
+
+# Saves space on ROM_IMAGE_SIZE, but decompression costs a second on boot
+option CONFIG_COMPRESS = 1
+
+romimage "fallback"
+ option USE_FALLBACK_IMAGE=1
+ option ROM_IMAGE_SIZE=64*1024
+ option COREBOOT_EXTRA_VERSION=".0Fallback"
+ payload ../payload.elf
+ # If getting payload from IDE
+ #payload /dev/null
+end
+
+buildrom ./coreboot.rom ROM_SIZE "fallback"
