coreboot-3.0.1161 Wed Mar 25 11:26:19 EDT 2009 starting...
(console_loglevel=8)
Choosing fallback boot.
LAR: Attempting to open 'fallback/initram/segment0'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: seen member normal/stage2/segment0@0xfff857b0, size 1
LAR: seen member normal/stage2/segment1@0xfff85810, size 25731
LAR: seen member normal/stage2/segment2@0xfff8bcf0, size 999
LAR: seen member normal/payload/segment0@0xfff8c130, size 1
LAR: seen member normal/payload/segment1@0xfff8c190, size 40402
LAR: seen member normal/payload/segment2@0xfff95fc0, size 47
LAR: seen member bootblock@0xffffafc0, size 20480
LAR: File not found!
LAR: Run file fallback/initram/segment0 failed: No such file.
Fallback failed. Try normal boot
LAR: Attempting to open 'normal/initram/segment0'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: CHECK normal/initram/segment0 @ 0xfff80430
start 0xfff80480 len 21284 reallen 21284 compression 0 entry 0x0000391f
loadaddress 0x00000000
Entry point is 0xfff83d9f
Hi there from stage1, cpu0, core0
Mobile Intel(R) 945GM/GME Express Chipset
(G)MCH capable of up to FSB 800 MHz
(G)MCH capable of up to DDR2-667
Setting up static southbridge registers... GPIOS... done.
Disabling Watchdog reboot... done.
Setting up static northbridge registers... done.
Waiting for MCHBAR to come up...ok
SMBus controller enabled.
Setting up RAM controller.
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
This mainboard supports only Single Channel Operation.
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
DDR II Channel 0 Socket 0: x8DDS
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
lowest common cas = 3
Probing Speed 2
DIMM: 0
Current CAS mask: 0038; idx=2, tCLK=50, tAC=60: Not fast enough!
Current CAS mask: 0030; idx=1, tCLK=3d, tAC=50: Not fast enough!
Current CAS mask: 0020; idx=0, tCLK=30, tAC=45: OK
DIMM: 1
freq_cas_mask for speed 2: 0020
Memory will be driven at 667MHz with CAS=5 clocks
tRAS = 15 cycles
tRP = 5 cycles
tRCD = 5 cycles
Refresh: 7.8us
tWR = 5 cycles
DIMM 0 side 0 = 512 MB
DIMM 0 side 1 = 512 MB
tRFC = 35 cycles
Setting Graphics Frequency...
Setting Memory Frequency... CLKCFG=0x00010023, CLKCFG=0x00010043, ok
Setting mode of operation for memory
channels...SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
Single Channel 0 only.
DCC=0x00000400
Programming Clock Crossing...MEM=667 FSB=667... ok
Setting RAM size...
C0DRB = 0x00002010
C1DRB = 0x00000000
TOLUD = 0x70
Setting row attributes...
C0DRA = 0x0033
C1DRA = 0x0000
one dimm per channel config..
Initializing System Memory IO...
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
Programming Single Channel RCOMP
Table Index: 19
Programming DLL Timings...
Enabling System Memory IO...
jedec enable sequence: bank 0
Apply NOP
Sending RAM command 0x00010400...done
ram read: 00000000
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 00000000
Extended Mode Register Set(2)
Sending RAM command 0x00240400...done
ram read: 00000000
Extended Mode Register Set(3)
Sending RAM command 0x00440400...done
ram read: 00000000
Extended Mode Register Set
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 00000020
MRS: Reset DLLs
Sending RAM command 0x00030400...done
ram read: 00004a98
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 00000000
CAS before RAS
Sending RAM command 0x00060400...done
ram read: 00000000
ram read: 00000000
MRS: Enable DLLs
Sending RAM command 0x00030400...done
ram read: 00004298
Extended Mode Register Set: ODT/OCD
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 00001c20
Extended Mode Register Set: OCD Exit
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 00000020
jedec enable sequence: bank 1
bankaddr from bank size of rank 0
Apply NOP
Sending RAM command 0x00010400...done
ram read: 20000000
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 20000000
Extended Mode Register Set(2)
Sending RAM command 0x00240400...done
ram read: 20000000
Extended Mode Register Set(3)
Sending RAM command 0x00440400...done
ram read: 20000000
Extended Mode Register Set
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 20000020
MRS: Reset DLLs
Sending RAM command 0x00030400...done
ram read: 20004a98
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 20000000
CAS before RAS
Sending RAM command 0x00060400...done
ram read: 20000000
ram read: 20000000
MRS: Enable DLLs
Sending RAM command 0x00030400...done
ram read: 20004298
Extended Mode Register Set: ODT/OCD
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 20001c20
Extended Mode Register Set: OCD Exit
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 20000020
jedec enable sequence: bank 4
bankaddr from bank size of rank 1
Apply NOP
Sending RAM command 0x00010400...done
ram read: 40000000
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 40000000
Extended Mode Register Set(2)
Sending RAM command 0x00240400...done
ram read: 40000000
Extended Mode Register Set(3)
Sending RAM command 0x00440400...done
ram read: 40000000
Extended Mode Register Set
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 40000020
MRS: Reset DLLs
Sending RAM command 0x00030400...done
ram read: 40004a98
All Banks Precharge
Sending RAM command 0x00020400...done
ram read: 40000000
CAS before RAS
Sending RAM command 0x00060400...done
ram read: 40000000
ram read: 40000000
MRS: Enable DLLs
Sending RAM command 0x00030400...done
ram read: 40004298
Extended Mode Register Set: ODT/OCD
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 40001c20
Extended Mode Register Set: OCD Exit
Sending RAM command 0x00040400...done
SDRAM_CAPABILITIES_DUAL_CHENAL = 0x00000000
ram read: 40000020
Normal Operation
Sending RAM command 0x000f0400...done
receive_enable_autoconfig() for channel 0
find_strobes_low()
set_receive_enable() medium=0x3, coarse=0x5
set_receive_enable() medium=0x1, coarse=0x5
find_strobes_edge()
set_receive_enable() medium=0x1, coarse=0x5
add_quarter_clock() mediumcoarse=15 fine=d7
set_receive_enable() medium=0x3, coarse=0x5
find_preamble()
set_receive_enable() medium=0x3, coarse=0x4
set_receive_enable() medium=0x3, coarse=0x3
add_quarter_clock() mediumcoarse=0f fine=57
normalize()
RAM initialization finished.
Setting up Egress Port RCRB
Loading port arbitration table ...ok
Wait for VC1 negotiation ...ok
Setting up DMI RCRB
Wait for VC1 negotiation ...timeout!
Waiting for DMI hardware...ok
Disabling PCI Express x16 Link
Wait for link to enter detect state... ok
Setting up Root Complex Topology
run_file returns with 0
Done RAM init code
Done printk() buffer move
disable_car entry
disable_car global_vars copy done
NEWLOCATION = 0x00088fc8
disable_car global_vars pointer adjusted
entering asm code now
LAR: Attempting to open 'normal/stage2/segment0'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: seen member normal/stage2/segment0@0xfff857b0, size 1
LAR: CHECK normal/stage2/segment0 @ 0xfff857b0
start 0xfff85800 len 1 reallen 194976 compression 3 entry 0x00002048
loadaddress 0x00016780
LAR: Compression algorithm #3 (zeroes) used
LAR: Attempting to open 'normal/stage2/segment1'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: seen member normal/stage2/segment0@0xfff857b0, size 1
LAR: seen member normal/stage2/segment1@0xfff85810, size 25731
LAR: CHECK normal/stage2/segment1 @ 0xfff85810
start 0xfff85860 len 25731 reallen 53312 compression 1 entry 0x00002048
loadaddress 0x00002000
LAR: Compression algorithm #1 (lzma) used
LAR: Attempting to open 'normal/stage2/segment2'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: seen member normal/stage2/segment0@0xfff857b0, size 1
LAR: seen member normal/stage2/segment1@0xfff85810, size 25731
LAR: seen member normal/stage2/segment2@0xfff8bcf0, size 999
LAR: CHECK normal/stage2/segment2 @ 0xfff8bcf0
start 0xfff8bd40 len 999 reallen 26420 compression 1 entry 0x00002048
loadaddress 0x00010040
LAR: Compression algorithm #1 (lzma) used
LAR: Attempting to open 'normal/stage2/segment3'.
LAR: Start 0xfff80000 len 0x80000
LAR: seen member normal/option_table@0xfff80000, size 984
LAR: seen member normal/initram/segment0@0xfff80430, size 21284
LAR: seen member normal/stage2/segment0@0xfff857b0, size 1
LAR: seen member normal/stage2/segment1@0xfff85810, size 25731
LAR: seen member normal/stage2/segment2@0xfff8bcf0, size 999
LAR: seen member normal/payload/segment0@0xfff8c130, size 1
LAR: seen member normal/payload/segment1@0xfff8c190, size 40402
LAR: seen member normal/payload/segment2@0xfff95fc0, size 47
LAR: seen member bootblock@0xffffafc0, size 20480
LAR: File not found!
LAR: load_file: No such file 'normal/stage2/segment3'
LAR: load_file_segments: All loaded, entry 0x00002048
resets at this point .
Best Regards,
Vadim
************************************************************************************
This footnote confirms that this email message has been scanned by
PineApp Mail-SeCure for the presence of malicious code, vandals & computer viruses.
************************************************************************************