Author: linux_junkie
Date: 2008-05-16 17:43:35 +0200 (Fri, 16 May 2008)
New Revision: 3328
Added:
trunk/coreboot-v2/src/mainboard/thomson/
trunk/coreboot-v2/src/mainboard/thomson/ip1000/
trunk/coreboot-v2/src/mainboard/thomson/ip1000/Config.lb
trunk/coreboot-v2/src/mainboard/thomson/ip1000/Options.lb
trunk/coreboot-v2/src/mainboard/thomson/ip1000/auto.c
trunk/coreboot-v2/src/mainboard/thomson/ip1000/chip.h
trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c
trunk/coreboot-v2/src/mainboard/thomson/ip1000/irq_tables.c
trunk/coreboot-v2/src/mainboard/thomson/ip1000/mainboard.c
trunk/coreboot-v2/src/mainboard/thomson/ip1000/spd_table.h
trunk/coreboot-v2/targets/thomson/
trunk/coreboot-v2/targets/thomson/ip1000/
trunk/coreboot-v2/targets/thomson/ip1000/Config-abuild.lb
trunk/coreboot-v2/targets/thomson/ip1000/Config.lb
Log:
New Target and initial support for the Thomson IP1000.
Signed-off-by: Joseph Smith <joe(a)settoplinux.org>
Acked-by: Stefan Reinauer <stepan(a)coresystems.de>
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/Config.lb
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/Config.lb (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/Config.lb 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,145 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = (ROM_SIZE - FALLBACK_SIZE)
+else
+ default ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE)
+ default ROM_SECTION_OFFSET = 0
+end
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
+default _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+default XIP_ROM_SIZE = 65536
+default XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
+arch i386 end
+driver mainboard.o
+if HAVE_PIRQ_TABLE object irq_tables.o end
+# object reset.o
+if HAVE_ACPI_TABLES
+ object fadt.o
+ object dsdt.o
+ object acpi_tables.o
+end
+makerule ./failover.E
+ depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+end
+makerule ./failover.inc
+ depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
+end
+makerule ./auto.E
+ # depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ depends "$(MAINBOARD)/auto.c ./romcc"
+ action "./romcc -E -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc
+ # depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ depends "$(MAINBOARD)/auto.c ./romcc"
+ action "./romcc -mcpu=p3 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+end
+mainboardinit arch/i386/lib/cpu_reset.inc
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+if USE_FALLBACK_IMAGE
+ ldscript /arch/i386/lib/failover.lds
+ mainboardinit ./failover.inc
+end
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
+dir /pc80
+config chip.h
+
+chip northbridge/intel/i82830 # Northbridge
+ device pci_domain 0 on # PCI domain
+ device pci 0.0 on end # Host bridge
+ chip drivers/pci/onboard # Onboard VGA
+ device pci 2.0 on end # VGA (Intel 82830 CGC)
+ register "rom_address" = "0xfff00000"
+ end
+ chip southbridge/intel/i82801xx # Southbridge
+ device pci 1d.0 on end # USB UHCI Controller #1
+ device pci 1d.1 on end # USB UHCI Controller #2
+ device pci 1d.2 on end # USB UHCI Controller #3
+ device pci 1d.7 on end # USB2 EHCI Controller
+ device pci 1e.0 on # PCI bridge
+ device pci 08.0 on end # Intel 82801DB PRO/100 VE Ethernet
+ end
+ device pci 1f.0 on # ISA/LPC bridge
+ chip superio/smsc/smscsuperio # Super I/O
+ device pnp 2e.0 off # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.3 on # Parallel port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ drq 0x74 = 4
+ end
+ device pnp 2e.4 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.5 on # Com2 / IR
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.7 on # PS/2 keyboard/mouse
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1 # Keyboard interrupt
+ irq 0x72 = 12 # Mouse interrupt
+ end
+ device pnp 2e.9 off end # Game port
+ device pnp 2e.a on # PME
+ io 0x60 = 0x800
+ end
+ device pnp 2e.b off end # MPU-401
+ end
+ end
+ device pci 1f.1 on end # IDE
+ device pci 1f.3 on end # SMBus
+ device pci 1f.5 on end # AC'97 audio
+ device pci 1f.6 off end # AC'97 modem
+ end
+ end
+ device apic_cluster 0 on # APIC cluster
+ chip cpu/intel/socket_PGA370 # Low Voltage PIII Micro-FCBGA Socket 479
+ device apic 0 on end # APIC
+ end
+ end
+end
+
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/Options.lb
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/Options.lb (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/Options.lb 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,95 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+uses CC
+uses CONFIG_CONSOLE_SERIAL8250
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_IOAPIC
+uses CONFIG_PCI_ROM_RUN
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+uses CONFIG_UDELAY_TSC
+uses CONFIG_VIDEO_MB
+uses CROSS_COMPILE
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses FALLBACK_SIZE
+uses HAVE_ACPI_TABLES
+uses HAVE_FALLBACK_BOOT
+uses HAVE_MP_TABLE
+uses HAVE_OPTION_TABLE
+uses HAVE_PIRQ_TABLE
+uses HEAP_SIZE
+uses HOSTCC
+uses IRQ_SLOT_COUNT
+uses COREBOOT_EXTRA_VERSION
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses OBJCOPY
+uses PAYLOAD_SIZE
+uses _RAMBASE
+uses _ROMBASE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses ROM_SIZE
+uses STACK_SIZE
+uses TTYS0_BASE
+uses TTYS0_BAUD
+uses TTYS0_LCS
+uses USE_FALLBACK_IMAGE
+uses USE_OPTION_TABLE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+
+default ROM_SIZE = 512 * 1024
+default ROM_IMAGE_SIZE = 128 * 1024
+default HAVE_FALLBACK_BOOT = 1
+default FALLBACK_SIZE = 256 * 1024
+default CONFIG_UDELAY_TSC = 1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
+default HAVE_PIRQ_TABLE = 1
+default IRQ_SLOT_COUNT = 7
+default HAVE_MP_TABLE = 0
+default HAVE_ACPI_TABLES = 0
+default CONFIG_IOAPIC = 0
+default HAVE_OPTION_TABLE = 0
+default CONFIG_CONSOLE_VGA = 0
+default CONFIG_PCI_ROM_RUN = 0
+default CONFIG_VIDEO_MB = 0
+default STACK_SIZE = 0x2000
+default HEAP_SIZE = 0x4000
+default _RAMBASE = 0x00004000
+default USE_OPTION_TABLE = 0
+default CONFIG_ROM_PAYLOAD = 1
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+default CONFIG_CONSOLE_SERIAL8250 = 1
+default TTYS0_BAUD = 115200
+default TTYS0_BASE = 0x3f8
+default TTYS0_LCS = 0x3 # 8n1
+default DEFAULT_CONSOLE_LOGLEVEL = 9
+default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default MAINBOARD_VENDOR = "THOMSON"
+default MAINBOARD_PART_NUMBER = "IP1000"
+end
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/auto.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/auto.c (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/auto.c 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,126 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <stdlib.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "pc80/udelay_io.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "superio/smsc/smscsuperio/smscsuperio_early_serial.c"
+#include "northbridge/intel/i82830/raminit.h"
+#include "northbridge/intel/i82830/memory_initialized.c"
+#include "southbridge/intel/i82801xx/i82801xx.h"
+#include "southbridge/intel/i82801xx/i82801xx_reset.c"
+#include "cpu/x86/mtrr/earlymtrr.c"
+#include "cpu/x86/bist.h"
+#include "spd_table.h"
+#include "gpio.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, SMSCSUPERIO_SP1)
+
+#include "southbridge/intel/i82801xx/i82801xx_early_smbus.c"
+#include "southbridge/intel/i82801xx/i82801xx_early_lpc.c"
+
+/**
+ * The onboard 64MB PC133 memory does not have a SPD EEPROM so the
+ * values have to be set manually, the SO-DIMM socket is located in
+ * socket0 (0x50), and the onboard memory is located in socket1 (0x51).
+ */
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+ int i;
+
+ if (device == 0x50) {
+ return smbus_read_byte(device, address);
+ } else if (device == 0x51) {
+ for (i = 0; i < ARRAY_SIZE(spd_table); i++) {
+ if (spd_table[i].address == address)
+ return spd_table[i].data;
+ }
+ return 0xFF; /* Return 0xFF when address is not found. */
+ } else {
+ return 0xFF; /* Return 0xFF on any failures. */
+ }
+}
+
+#include "northbridge/intel/i82830/raminit.c"
+#include "sdram/generic_sdram.c"
+
+/**
+ * The AC'97 Audio Controller I/O space registers are read only by default
+ * so we need to enable them by setting register 0x41 to 0x01.
+ */
+static void ac97_io_enable(void)
+{
+ device_t dev;
+
+ /* Set the ac97 audio device staticly. */
+ dev = PCI_DEV(0x0, 0x1f, 0x5);
+
+ /* Enable access to the IO space. */
+ pci_write_config8(dev, 0x41, 0x01);
+}
+
+static void main(unsigned long bist)
+{
+ static const struct mem_controller memctrl[] = {
+ {
+ .d0 = PCI_DEV(0, 0, 0),
+ .channel0 = {0x50, 0x51},
+ }
+ };
+
+ if (bist == 0)
+ early_mtrr_init();
+ if (memory_initialized()) {
+ hard_reset();
+ }
+
+ enable_smbus();
+
+ smscsuperio_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ mb_gpio_init();
+ uart_init();
+ console_init();
+
+ /* Prevent the TCO timer from rebooting us */
+ i82801xx_halt_tco_timer();
+
+ /* Halt if there was a built in self test failure. */
+ report_bist_failure(bist);
+
+ sdram_set_registers(memctrl);
+ sdram_set_spd_registers(memctrl);
+ sdram_enable(0, memctrl);
+
+ /* Check RAM. */
+ /* ram_check(0, 640 * 1024); */
+ /* ram_check(64512 * 1024, 65536 * 1024); */
+
+ ac97_io_enable();
+}
Property changes on: trunk/coreboot-v2/src/mainboard/thomson/ip1000/auto.c
___________________________________________________________________
Added: svn:executable
+ *
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/chip.h
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/chip.h (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/chip.h 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,25 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_thomson_ip1000_ops;
+
+struct mainboard_thomson_ip1000_config {
+ int nothing;
+};
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,120 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define PME_DEV PNP_DEV(0x2e, 0x0a)
+#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */
+#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+ device_t dev;
+ uint16_t port;
+ uint32_t set_gpio;
+
+ /* Southbridge GPIOs. */
+ /* Set the LPC device statically. */
+ dev = PCI_DEV(0x0, 0x1f, 0x0);
+
+ /* Set the value for GPIO base address register and enable GPIO. */
+ pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+
+ /* Set GPIO25 to input and drive GPIO23 to high,
+ * this enables the LAN controller.
+ */
+ udelay(10);
+ set_gpio = 0x0000ffff;
+ set_gpio |= 1 << 25;
+ outl(set_gpio, ICH_IO_BASE_ADDR + 0x04);
+
+ set_gpio = 0x1b3f0000;
+ set_gpio |= 1 << 23;
+ outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
+
+ /* Super I/O GPIOs. */
+ dev = PME_DEV;
+ port = dev >> 8;
+
+ outb(0x55, port); /* Enter the configuration state. */
+ pnp_set_logical_device(dev);
+ pnp_set_enable(dev, 0);
+ pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
+ pnp_set_enable(dev, 1);
+ outl(0x03, PME_IO_BASE_ADDR + 0x1e); /* Force Disk Change */
+ outl(0x02, PME_IO_BASE_ADDR + 0x1f); /* Floppy Data Rate */
+ outl(0x81, PME_IO_BASE_ADDR + 0x20); /* UART1 FIFO */
+ outl(0x81, PME_IO_BASE_ADDR + 0x21); /* UART2 FIFO */
+ outl(0x00, PME_IO_BASE_ADDR + 0x22); /* Device Disable */
+ outl(0x01, PME_IO_BASE_ADDR + 0x23); /* GP10 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x24); /* GP11 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x25); /* GP12 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x26); /* GP13 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x27); /* GP14 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x28); /* GP15 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x29); /* GP16 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2a); /* GP17 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2b); /* GP20 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2c); /* GP21 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2d); /* GP22 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2f); /* GP24 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x30); /* GP25 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x31); /* GP26 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x32); /* GP27 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x33); /* GP30 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x34); /* GP31 */
+ outl(0x84, PME_IO_BASE_ADDR + 0x35); /* GP32 */
+ outl(0x84, PME_IO_BASE_ADDR + 0x36); /* GP33 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x37); /* GP34 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x38); /* GP35 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x39); /* GP36 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x3a); /* GP37 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x3b); /* GP40 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x3c); /* GP41 */
+ outl(0x86, PME_IO_BASE_ADDR + 0x3d); /* GP42 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x3e); /* GP43 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x3f); /* GP50 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x40); /* GP51 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x41); /* GP52 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x42); /* GP53 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x43); /* GP54 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x44); /* GP55 */
+ outl(0x05, PME_IO_BASE_ADDR + 0x45); /* GP56 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x46); /* GP57 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x47); /* GP58 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x48); /* GP59 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x4b); /* GP1 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x4c); /* GP2 */
+ outl(0xc0, PME_IO_BASE_ADDR + 0x4d); /* GP3 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x4e); /* GP4 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x4f); /* GP5 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x50); /* GP6 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x56); /* FAN1 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x57); /* FAN2 */
+ outl(0x58, PME_IO_BASE_ADDR + 0x58); /* Fan Control */
+ outl(0xff, PME_IO_BASE_ADDR + 0x59); /* Fan1 Tachometer */
+ outl(0x50, PME_IO_BASE_ADDR + 0x5a); /* Fan2 Tachometer */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5b); /* Fan1 Preload */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5c); /* Fan2 Preload */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5d); /* LED1 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5e); /* LED2 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5f); /* Keyboard Scan Code */
+ outb(0xaa, port); /* Exit the configuration state. */
+}
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/irq_tables.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/irq_tables.c (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/irq_tables.c 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,50 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*IRQ_SLOT_COUNT, /* there can be total 7 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
+ 0, /* IRQs devoted exclusively to PCI usage */
+ 0x8086, /* Vendor */
+ 0x24c0, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0xcd, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00,(0x02<<3)|0x0, {{0x60, 0x1ef8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, /* [A] VGA compatible controller */
+ {0x00,(0x1d<<3)|0x0, {{0x60, 0x1ef8}, {0x63, 0x1ef8}, {0x62, 0x1ef8}, {0x6b, 0x01ef8}}, 0x0, 0x0}, /* [D] USB2 EHCI Controller */
+ {0x00,(0x1f<<3)|0x0, {{0x62, 0x1ef8}, {0x61, 0x1ef8}, {0x6b, 0x1ef8}, {0x63, 0x01ef8}}, 0x0, 0x0}, /* [A] IDE Controller */
+ {0x01,(0x08<<3)|0x0, {{0x68, 0x1ef8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, /* [A] Ethernet controller */
+ {0x01,(0x00<<3)|0x0, {{0x60, 0x1ef8}, {0x61, 0x1ef8}, {0x62, 0x1ef8}, {0x63, 0x01ef8}}, 0x1, 0x0}, /* [A] USB UHCI Controller #1 */
+ {0x01,(0x01<<3)|0x0, {{0x63, 0x1ef8}, {0x60, 0x1ef8}, {0x61, 0x1ef8}, {0x62, 0x01ef8}}, 0x2, 0x0}, /* [B] USB UHCI Controller #2 */
+ {0x01,(0x02<<3)|0x0, {{0x62, 0x1ef8}, {0x63, 0x1ef8}, {0x60, 0x1ef8}, {0x61, 0x01ef8}}, 0x3, 0x0}, /* [C] USB UHCI Controller #3 */
+ }
+};
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/mainboard.c
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/mainboard.c (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/mainboard.c 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,26 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <device/device.h>
+#include "chip.h"
+
+struct chip_operations mainboard_thomson_ip1000_ops = {
+ CHIP_NAME("THOMSON IP1000 Mainboard")
+};
Added: trunk/coreboot-v2/src/mainboard/thomson/ip1000/spd_table.h
===================================================================
--- trunk/coreboot-v2/src/mainboard/thomson/ip1000/spd_table.h (rev 0)
+++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/spd_table.h 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,40 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <spd.h>
+
+struct spd_entry {
+ unsigned int address;
+ unsigned int data;
+};
+
+/*
+ * The onboard 64MB PC133 memory does not have an SPD EEPROM so the values
+ * have to be set manually, the onboard memory is located in socket1 (0x51).
+ */
+const struct spd_entry spd_table [] = {
+ {SPD_MEMORY_TYPE, 0x04}, /* (Fundamental) memory type */
+ {SPD_NUM_COLUMNS, 0x09}, /* Number of column address bits */
+ {SPD_NUM_DIMM_BANKS, 0x01}, /* Number of module rows (banks) */
+ {SPD_MODULE_DATA_WIDTH_LSB, 0x40}, /* Module data width (LSB) */
+ {SPD_MIN_CYCLE_TIME_AT_CAS_MAX, 0x75}, /* SDRAM cycle time (highest CAS latency), RAS access time (tRAC) */
+ {SPD_ACCESS_TIME_FROM_CLOCK, 0x54}, /* SDRAM access time from clock (highest CAS latency), CAS access time (Tac, tCAC) */
+ {SPD_DENSITY_OF_EACH_ROW_ON_MODULE, 0x10}, /* Density of each row on module */
+};
Added: trunk/coreboot-v2/targets/thomson/ip1000/Config-abuild.lb
===================================================================
--- trunk/coreboot-v2/targets/thomson/ip1000/Config-abuild.lb (rev 0)
+++ trunk/coreboot-v2/targets/thomson/ip1000/Config-abuild.lb 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,30 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+target thomson_ip1000
+mainboard thomson/ip1000
+
+romimage "fallback"
+ option USE_FALLBACK_IMAGE = 1
+ payload __PAYLOAD__
+end
+
+buildrom ./coreboot.rom ROM_SIZE "fallback"
+
Added: trunk/coreboot-v2/targets/thomson/ip1000/Config.lb
===================================================================
--- trunk/coreboot-v2/targets/thomson/ip1000/Config.lb (rev 0)
+++ trunk/coreboot-v2/targets/thomson/ip1000/Config.lb 2008-05-16 15:43:35 UTC (rev 3328)
@@ -0,0 +1,63 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2008 Joseph Smith <joe(a)settoplinux.org>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+target ip1000
+mainboard thomson/ip1000
+
+##
+## Total number of bytes allocated for coreboot use
+## (fallback images and payloads).
+##
+# option ROM_SIZE = 1024 * 1024
+## For VGA BIOS (-64k)
+option ROM_SIZE = (1024 * 1024) - (64 * 1024)
+
+##
+## VGA Console
+## NOTE: to initialize VGA, you need to copy
+## the VGA option ROM from the factory BIOS
+## 0=disable 1=enable
+##
+option CONFIG_CONSOLE_VGA = 1
+option CONFIG_PCI_ROM_RUN = 1
+
+##
+## Choose the amount of memory pre-allocated for VGA
+## 0 for No memory pre-allocated (Graphics memory Disabled)
+## 512 for DVMT (UMA) mode, 512K of memory pre-allocated for frame buffer
+## 1 for DVMT (UMA) mode, 1M of memory pre-allocated for frame buffer
+## 8 for DVMT (UMA) mode, 8M of memory pre-allocated for frame buffer
+##
+option CONFIG_VIDEO_MB = 8
+
+##
+## Request this level of debugging output
+##
+option DEFAULT_CONSOLE_LOGLEVEL = 7
+
+romimage "fallback"
+ option USE_FALLBACK_IMAGE = 1
+ option FALLBACK_SIZE = ROM_SIZE
+ option COREBOOT_EXTRA_VERSION = "_IP1000"
+ payload /tmp/filo.elf
+# payload /tmp/eb-5.4.3-eepro100.elf
+end
+
+buildrom ./coreboot.rom ROM_SIZE "fallback"
