coreboot April 2007

coreboot@coreboot.org

76 participants
281 discussions

[LinuxBIOS] How to enable VGA on Tyan S3992?
by Feng, Libo 27 Apr '07

27 Apr '07

I have adapted LB of MSI ms9185 to Tyan S3992. It runs well and comes to the grub command line of Filo. Special thanks to Mr. Lu Yinghai. The last task is how to enable VGA on Tyan S3992. I have gotten ATI ES1000 VGA BIOS from Tyan web site with Mr. Anton Borisov's tool. It is 36KB. I concatenate it with LB image, 512KB. default CONFIG_CONSOLE_VGA=1 default CONFIG_PCI_ROM_RUN=1 in mainboard/msi/ms9185/Options.lb. I am not sure about the below: device pci 9.0 on # PCI chip drivers/pci/onboard device pci 9.0 on end register "rom_address" = "0xfff80000" #512k image #register "rom_address" = "0xfff00000" #1M image end end I check device number on Windows, it is 12, but the broadcom spec says it is 13. I have tried both, it didn't work. What should be set here? And the device number is hex or decimal? What else variable should be set in config file? Do I need to switch the console from serial port to VGA? How? Thank you very much. Best Regards 丰立波 Feng Libo @ AMD Ext: 20906 Mobile Phone: 13683249071 Office Phone: 0086-010-62801406

3 11

[LinuxBIOS] question about debug skill in linuxbios
by AlexHuang 26 Apr '07

26 Apr '07

Hi All, I am a novice in LinuxBIOS. I am porting a system now. I see the linuxbios code with many "print_XXX" code. How can I see these messages during post stage?? It's hard for me to check the bug point using post_card and not efficiency. Thanks for your help. Alex

2 1

[LinuxBIOS] r2619 build service
by LinuxBIOS information 26 Apr '07

26 Apr '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "stepan" checked in revision 2619 to the LinuxBIOS source repository and caused the following changes: Change Log: Activate EC for access to fan speeds and temperature sensors. Signed-off-by: Ward Vandewege <ward(a)gnu.org> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Build Log: Compilation of arima:hdama is still broken Compilation of ibm:e325 is still broken Compilation of ibm:e326 is still broken Compilation of iwill:dk8s2 is still broken Compilation of iwill:dk8x is still broken If something broke during this checkin please be a pain in stepan's neck until the issue is fixed. If this issue is not fixed within 24h the revision will be backed out. Yours truely, LinuxBIOS automatic build system

5 5

[LinuxBIOS] GA-M57SLI-S4 problems
by ST 26 Apr '07

26 Apr '07

Hi Since the build problems of the GA-M57SLI-S4 mb where gone i tried installing the bios on my mainboard. Well it worked... mostly. The i2c part doesn't work as documented by Ward. But also all PCI cards are missing. They are not listed in with lspci. There is s.t. suspicious in the dmesg output (see below). Fortunately i can report that my little soldering work is working fine. I can switch between original Bios and Linuxbios. When running linuxbios i can't do a reboot but have to powercycle the system, but that is a minor setback. Best Regards ST suspicious dmesg output: pnp: PnP ACPI: disabled SCSI subsystem initialized libata version 2.20 loaded. PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Boot video device is 0000:07:00.0 PCI: Using IRQ router default [10de/0370] at 0000:00:06.0 PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20 PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21 PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:07:00.0[A] -> IRQ 17 NET: Registered protocol family 8 NET: Registered protocol family 20 pnp: the driver 'system' has been registered PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0f.0 IO window: 1000-1fff MEM window: f4000000-f60fffff PREFETCH window: e0000000-efffffff PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:0a.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Setting latency timer of device 0000:00:0f.0 to 64

2 1

[LinuxBIOS] r2619 - trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli
by svn＠openbios.org 26 Apr '07

26 Apr '07

Author: stepan Date: 2007-04-26 22:55:45 +0200 (Thu, 26 Apr 2007) New Revision: 2619 Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb Log: Activate EC for access to fan speeds and temperature sensors. Signed-off-by: Ward Vandewege <ward(a)gnu.org> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-04-25 00:23:39 UTC (rev 2618) +++ trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-04-26 20:55:45 UTC (rev 2619) @@ -256,7 +256,10 @@ io 0x60 = 0x378 irq 0x70 = 7 end - device pnp 2e.4 off # EC + device pnp 2e.4 on # EC + io 0x60 = 0x290 + io 0x62 = 0x230 + irq 0x70 = 9 end device pnp 2e.5 on # Keyboard io 0x60 = 0x60 @@ -268,7 +271,7 @@ end device pnp 2e.8 off # MIDI io 0x60 = 0x300 - irq 0x70 = 9 + irq 0x70 = 10 end device pnp 2e.9 off # GAME io 0x60 = 0x220

1 0

[LinuxBIOS] VMWare almost there, IDE problems
by Joe Pub 26 Apr '07

26 Apr '07

Hi All, I am getting ever so closer to booting VMWare with LinuxBIOS. I can boot FILO with VGA within VMWare now but I have a final hurdle. I am getting IDE problems within FILO when it's trying to read sector 0 of the boot drive. I get a 'read sector failed' error so because of this it just jumps straight to the GRUB menu. Anyone have any ideas what the problem might be? Below is a copy of the output from LinuxBIOS from start to end. Thanks guys. LinuxBIOS-2.0.0.0Fallback Tue Apr 24 12:30:11 BST 2007 starting... Northbridge prior to SDRAM init: PCI: 00:00.00 00: 86 80 90 71 06 00 10 02 01 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 ad 15 76 19 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 40 80 80 80 80 80 80 80 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Set register 0x00000050 to 0xff00a00c Set register 0x00000057 to 0x00000008 Set register 0x00000059 to 0x00000010 Set register 0x0000005a to 0x00000011 Set register 0x0000005b to 0x00000001 Set register 0x0000005c to 0x00000000 Set register 0x0000005d to 0x00000030 Set register 0x0000005e to 0x00000013 Set register 0x0000005f to 0x00000011 Set register 0x00000060 to 0x00000000 Set register 0x00000061 to 0x00000000 Set register 0x00000062 to 0x00000000 Set register 0x00000063 to 0x00000000 Set register 0x00000064 to 0x00000000 Set register 0x00000065 to 0x00000000 Set register 0x00000066 to 0x00000000 Set register 0x00000067 to 0x00000000 Set register 0x00000068 to 0x00000000 Set register 0x00000074 to 0x00000000 Set register 0x00000076 to 0x00000000 Set register 0x00000078 to 0x0000ff00 Set register 0x0000007a to 0x00000000 RAM Enable 1: Apply NOP Sending RAM command 0x0020 to 0x00000000 RAM Enable 2: Precharge all Sending RAM command 0x0040 to 0x00000000 RAM Enable 3: CBR Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 Sending RAM command 0x0080 to 0x00000000 RAM Enable 4: Mode register set Sending RAM command 0x0060 to 0x000001d0 RAM Enable 5: Normal operation Sending RAM command 0x0000 to 0x00000000 RAM Enable 6: Enable refresh Northbridge following SDRAM init: PCI: 00:00.00 00: 86 80 90 71 06 00 10 02 01 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 ad 15 76 19 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 08 80 00 ff 00 00 00 00 01 30 33 33 33 33 00 00 60: 40 80 80 80 80 80 80 80 00 00 00 00 00 00 00 00 70: 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Copying LinuxBIOS to RAM. Jumping to LinuxBIOS. LinuxBIOS-2.0.0.0Fallback Tue Apr 24 12:30:11 BST 2007 booting... clocks_per_usec: 19933 Enumerating buses... Initializing VMWare keyboard Finding PCI configuration type. PCI: Using configuration type 1 PCI_DOMAIN: 0000 enabled PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [8086/7190] enabled PCI: 00:01.0 [8086/7191] enabled PCI: 00:07.0 [8086/7110] enabled PCI: 00:07.1 [8086/7111] enabled PCI: 00:07.3 [8086/7113] enabled PCI: 00:0f.0 [15ad/0405] enabled PCI: 00:10.0 [1000/0030] disabled PCI: 00:11.0 [1022/2000] enabled PCI: pci_scan_bus for bus 01 PCI: pci_scan_bus returning with max=001 PCI: pci_scan_bus returning with max=001 done Allocating resources... Reading resources... PCI: 00:01.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io PCI: 00:01.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem PCI: 00:01.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem Done reading resources. Allocating VGA resource PCI: 00:0f.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... I would like to set RAM size to 1024MB PCI: 00:07.1 20 <- [0x0000001080 - 0x000000108f] io PCI: 00:0f.0 10 <- [0x0000001090 - 0x000000109f] io PCI: 00:0f.0 14 <- [0x00f0000000 - 0x00f7ffffff] mem PCI: 00:0f.0 18 <- [0x00f8000000 - 0x00f87fffff] mem PCI: 00:0f.0 30 <- [0x00f8810000 - 0x00f8817fff] romem PCI: 00:11.0 10 <- [0x0000001000 - 0x000000107f] io PCI: 00:11.0 30 <- [0x00f8800000 - 0x00f880ffff] romem Done setting resources. Done allocating resources. Enabling resources... PCI: 00:00.0 cmd <- 146 PCI: 00:01.0 bridge ctrl <- 0083 PCI: 00:01.0 cmd <- 140 PCI: 00:07.0 subsystem <- 00/00 PCI: 00:07.0 cmd <- 147 PCI: 00:07.1 cmd <- 141 PCI: 00:07.3 cmd <- 141 PCI: 00:0f.0 cmd <- 143 PCI: 00:11.0 cmd <- 143 done. Initializing devices... Root Device init PCI: 00:00.0 init PCI: 00:07.0 init PCI: 00:07.1 init Enabling primary IDE interface PCI: 00:07.3 init PCI: 00:0f.0 init rom address for PCI: 00:0f.0 = f8810000 copying VGA ROM Image from 0xf8810000 to 0xc0000, 0x8000 bytes entering emulator halt_sys: file /root/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 PCI: 00:11.0 init rom address for PCI: 00:11.0 = f8800000 Class Code mismatch ROM 00000003, dev 00020000 copying non-VGA ROM Image from 0xf8800000 to 0xd0000, 0x8800 bytes entering emulator halt_sys: file /root/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 Devices initialized Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0000 to 0x000f0000 Wrote linuxbios table at: 00000530 - 000006d4 checksum 4765 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 rom_stream: 0xfffd0000 - 0xfffeffff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x41da0 offset 0xc0 filesize 0x17da8 (cleaned up) New segment addr 0x100000 size 0x41da0 offset 0xc0 filesize 0x17da8 New segment addr 0x141da0 size 0x48 offset 0x17e80 filesize 0x48 (cleaned up) New segment addr 0x141da0 size 0x48 offset 0x17e80 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000041da0 filesz: 0x0000000000017da8 Clearing Segment: addr: 0x0000000000117da8 memsz: 0x0000000000029ff8 Loading Segment: addr: 0x0000000000141da0 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to elf boot code at 0x111314 FILO version 0.5 (root(a)devilenc-linux.first4internet.co.uk) Tue Apr 24 12:22:22 BST 2007 collect_sys_info: boot eax = 0xe1fb007 collect_sys_info: boot ebx = 0x3fff59e0 collect_sys_info: boot arg = 0x3fff59e0 malloc_diag: alloc: 0 bytes (0 blocks), free: 16376 bytes (1 blocks) malloc_diag: alloc: 24 bytes (1 blocks), free: 16352 bytes (1 blocks) collect_elfboot_info: Bootloader: elfboot collect_elfboot_info: Version: 1.3 malloc_diag: alloc: 40 bytes (2 blocks), free: 16336 bytes (1 blocks) collect_linuxbios_info: Searching for LinuxBIOS tables... find_lb_table: Found canidate at: 00000530 find_lb_table: header checksum o.k. find_lb_table: table checksum o.k. find_lb_table: record count o.k. collect_linuxbios_info: Found LinuxBIOS table at: 00000530 convert_memmap: 0x00000000000000 0x00000000001000 16 convert_memmap: 0x00000000001000 0x0000000009f000 1 convert_memmap: 0x000000000c0000 0x00000000030000 1 convert_memmap: 0x000000000f0000 0x00000000010000 16 convert_memmap: 0x00000000100000 0x0000003ff00000 1 collect_sys_info: 0000000000001000-00000000000a0000 collect_sys_info: 00000000000c0000-00000000000f0000 collect_sys_info: 0000000000100000-0000000040000000 collect_sys_info: RAM 1024 MB relocate: Current location: 0x100000-0x141de7 relocate: Relocating to 0x3ffbe210-0x3ffffff7... ok setup_timers: CPU 2414 MHz pci_init: Scanning PCI: found 8 devices malloc_diag: alloc: 144 bytes (3 blocks), free: 16232 bytes (1 blocks) pci_init: 00:00.0 8086:7190 0600 00 pci_init: 00:01.0 8086:7191 0604 00 pci_init: 00:07.0 8086:7110 0601 00 pci_init: 00:07.1 8086:7111 0101 8a pci_init: 00:07.3 8086:7113 0680 00 pci_init: 00:0f.0 15ad:0405 0300 00 pci_init: 00:10.0 1000:0030 0100 00 pci_init: 00:11.0 1022:2000 0200 00 menu: hda1:/boot/grub/menu.lst malloc_diag: alloc: 160 bytes (4 blocks), free: 16216 bytes (1 blocks) file_open: dev=hda1, path=/boot/grub/menu.lst find_ide_controller: found PCI IDE controller 8086:7111 prog_if=0x8a find_ide_controller: primary channel: compatibility mode find_ide_controller: cmd_base=0x1f0 ctrl_base=0x3f4 ide_software_reset: Waiting for ide0 to become ready for reset... ok init_drive: Testing for hda init_drive: Probing for hda init_drive: LBA mode, sectors=2097152 init_drive: Init device params... ok hda: LBA 1073MB: VMware Virtual IDE Hard Drive init_drive: Testing for hdb init_drive: Testing for hdb IDE time out Disk read error dev=1 drive=0 sector=0 devread: read sector failed open_pc_partition: device read failed devopen: can't open partition 1 malloc_diag: alloc: 144 bytes (3 blocks), free: 16232 bytes (1 blocks)

4 7

Re: [LinuxBIOS] about programming BIOS Savior
by Mondrian Nuessle 26 Apr '07

26 Apr '07

Yes, when I looked around for good pci vendor/device ids respectively subsystem ids, I got the impression that are no unambiguous ids. Identification works perfectly once LinuxBIOS is booted using the LinuxBios supplied vendor/part. My suggestion then would be to remove matching of the board based on PCI ids for the DK8-HTX. Instead matching should only be done based on the name. If flashrom is used on a system booted by factory BIOS, the flash might fail (actually only if you have flash write protection enbaled in the factory BIOS setup). One need to provide board name on the command line. This seems to be much safer than guessing what board we're on and the fiddling with the GPIOs... Of course, this should also be documented, and maybe a warning message if the board could not be identified should be printed. I could provide a patch in that direction. What do you think? Mondrian -- Mondrian Nuessle University of Mannheim Phone: +49 621 181 2717 Computer Architecture Group Fax: +49 621 181 2713 http://ra.ti.uni-mannheim.de mailto:nuessle@uni-mannheim.de

3 4

[LinuxBIOS] register settings 5780, 5785
by Thomas Ekstrand 26 Apr '07

26 Apr '07

Hi! I'd like to change some register settings in bcm5780 and 5785. I don't know how this works, I have tried to scout the code for someplace where the registers are set but with no luck. Where would this be done? Thanks in advance! Thomas

2 1

[LinuxBIOS] [PATCH] flashrom patch for iwill dk8_htx
by Mondrian Nuessle 26 Apr '07

26 Apr '07

The attached patch enables flashing on the Iwill DK8-HTX board. Basically, it configures the SuperIO to set the right GPIO pins, so write protection is disabled. Signed-off-by: Mondrian Nuessle <nuessle(a)uni-mannheim.de> --- This patch should help those people that try to use flashrom on an iwill dk8_htx board, with or without biossavior, on factory BIOS or Linuxbios. Regards, Mondrian -- Mondrian Nuessle University of Mannheim Phone: +49 621 181 2717 Computer Architecture Group Fax: +49 621 181 2713 http://ra.ti.uni-mannheim.de mailto:nuessle@uni-mannheim.de

4 15

Re: [LinuxBIOS] Random Bios Postcodes after 0x88 with 440BX
by roger 26 Apr '07

26 Apr '07

On Thu, 2007-04-26 at 00:36 -0700, roger wrote: One last note, with LinuxBiosv2 code that was imported from LinuxBiosv1: The w83977ef code used in LinuxBiosv1 had an "ifdef" for the TF chip version to enabled "CIR_DEVICE=6". For the EF chip version, this isn't needed. The LinuxBiosv1 code defined the iobase for each device while the LinuxBiosv2 code for the w83977tf defines the for plugandplay? Noticing maybe a different iobase instead of 0x3f0 being used. Well, I'll research the w83977* specs. -- Roger http://www.eskimo.com/~roger/index.html Key fingerprint = 8977 A252 2623 F567 70CD 1261 640F C963 1005 1D61 Thu Apr 26 02:58:02 PDT 2007

1 0

← Newer
1
2
3
4
5
6
7
8
9
...
29
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot April 2007