coreboot

coreboot@coreboot.org

6 participants
39707 discussions

how to set 100 FSB for sis630
by tu guangxiu 12 Jul '03

12 Jul '03

I need my winfast6300( using sis630 )to support 100M FSB. I know that there is sis630.reg, who has some glues to set FSB from 66 to 100 in sis630.reg or other file? thanks __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com

1 0

Re: K8 + 2.4.21 + SuSE 64-bit mode + Arima HDAMA + 49LF040 + MTD
by YhLu 12 Jul '03

12 Jul '03

Eric, I switch to RH preview AMD 64 to build the kernel now the MB can finish the booting. I also try to boot local HD in normal boot. I use hda1 to store elf ( Kernel+RAM disk). But LinuxBIOS seems don't recogonize the elf format. And failed. I have use tg3.zelf to substitute the elf in the HD. LinuxBIOS can load it from HD and execute it. Any idea to produce ELF for HD booting. Or LinuxBIOS now only support 23bit elf? Regards Yinghai Lu

2 1

ANN: arima hdama boots...
by ebiederman＠lnxi.com 12 Jul '03

12 Jul '03

I have finally gotten all of the hard codes out of the memory initialization code and I can get the Arima HDAMA dual Opteron motherboard booting. And I have checked in the code. There is a lot more to do including cleanup of the code that works but one major piece is done. Eric

1 0

freebios2 and $Id:
by ebiederman＠lnxi.com 12 Jul '03

12 Jul '03

Unless someone has something to say in defense of the $Id: construct I am hereby banning it from the freebios2 tree. It makes it a pain to maintain a secondary CVS tree in sync as there are multiple unnecessary hits. Didn't we already ban $Id: ? in freebios2. In any case a huge lot of them had slipped in and I have removed all of them from the tree. And I intend to keep doing that when ever I find more of them. Eric

1 0

Any EPIA etherboot success stories?
by David Hendricks 11 Jul '03

11 Jul '03

I see a lot of people here have gotten LinuxBIOS working with the Via EPIA using an IDE device, but has anyone managed to get it working using etherboot to boot a kernel over a network? I'm a hopeless newbie and have been struggling with this for some time. I have links to logs, my payload, and my config below (Trying to keep the list archives tidy). I had gotten etherboot working with the PCM-5823s earlier and compared the minicom log with that of my Epia. The only real obvious discrepency I see is the entry point. The Geode entered at 0x00094000 (606,208), while the Epia is trying to enter at 0x00020000 (131,072). I'm using CVS versions of Etherboot and LinuxBios. However, I haven't been able to update in the past one or two weeks due to Sourceforge's problems so I might have missed an important patch. Links EPIA minicom log (High verbosity): http://www.flagen.com/~sc/linux/funstuff/epia-dave My Rhine payload: http://www.flagen.com/~sc/linux/funstuff/via-rhine-ebcvs.elf My config file: http://www.flagen.com/~sc/linux/funstuff/epia.config Geode (Elfboot part only): http://www.flagen.com/~sc/linux/funstuff/geode-elfboot-dave TIA --David

4 6

Where to buy the a Matsonic MS7308E
by Heinz N. Gies 10 Jul '03

10 Jul '03

hi i read your nice sis630 howto, after i finished ther are stilll some questions at first a very essential problem: where to get such a 'Matsonic MS7308E', i googled for it but only fins ome sides i japaneso or some language wich i can't differ as dumb european ;) and the side from ledtech where i don't find a suplier too :( so if someone know where to get this fine mainbords to but a LinuxBIOS on, please tell em :D secend question: did i realy need this FIZ if i wrrite the FlashRom in the same machine i want to use it? (cause it is very expensiv ... and i am just a poor student) third and fourth question: did i need an additional flashrom or can i use the buildin bios as flashrom and (i read that with an 4mb flash it is possible to put the whole boot proces in it) is possible to get a larger rom (and what is a n approx. price for such a 'ting') please excure my bad englsh thx Heinz N. Gies

1 0

ide-spinup.patch
by Devi Priya 10 Jul '03

10 Jul '03

Hello, I am using the kernel version 2.4.18-14. I guess the patch ide-spinup.patch is given for 2.4.7 . What patch shall I apply for 2.4.18-14? Thanks in advance for any help! _________________________________________________________________ Dress up your desktop! Get the best wallpapers. http://server1.msn.co.in/msnchannels/Entertainment/wallpaperhome.asp Just click here!

1 0

Is Intel 810 chipset supported?
by Devi Priya 10 Jul '03

10 Jul '03

I am having the Intel 810 chipset with onboard graphics controller. Can I use linux bios for this? _________________________________________________________________ Race along with NK. The fastest Indian http://server1.msn.co.in/sp03/tataracing/index.asp Feel the thrill!

1 0

ga-6bxc
by lichaojun 10 Jul '03

10 Jul '03

hi! i got a ga-6bxc and download freebios from cvs.when complie it ,it say: linuxbios_c.o: In function 'mainboard_fixup': linuxbios_c.o(.text+0x10b9): undefined reference to 'pci_zero_irq_setting' anybody can help me! i want to my ga-6bxc (with 2 Mb flash) boot from ide disk,using etherboot could give me a config file!

1 0

config
by Devi Priya 10 Jul '03

10 Jul '03

Hello, I have 2.4.18-14 Redhat linux kernel.To use linux bios for sc1200, which .config file from kernel_patches directory should I use? Can I use the same the same configuration as 2.4.18-14? Thanks in advance for any help! _________________________________________________________________ Race along with NK. The fastest Indian http://server1.msn.co.in/sp03/tataracing/index.asp Feel the thrill!

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot