coreboot December 2009

coreboot@coreboot.org

49 participants
169 discussions

#144: TYAN S7012 support
by coreboot 16 Jan '10

16 Jan '10

#144: TYAN S7012 support --------------------------------------------------------+------------------- Reporter: john@… | Owner: somebody Type: defect | Status: new Priority: major | Milestone: Component: flashrom | Version: v2 Keywords: TYAN S7012 Intel ICH10R SST SST25VF032B | Dependencies: Patchstatus: there is no patch | --------------------------------------------------------+------------------- I'm unable to flash a system that runs on a TYAN S7012 motherboard. # flashrom -w bios.bin flashrom v0.9.0-r659 No coreboot table found. Found chipset "Intel ICH10R", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Calibrating delay loop... OK. Found chip "SST SST25VF032B" (4096 KB, SPI) at physical address 0xffc00000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... COMPLETE. Verifying flash... VERIFY FAILED at 0x00002000! Expected=0x00, Read=0xff Running it with verbose the following error messages are printed out (repeating). Writing flash chip... Invalid OPCODE 0x06 due to SPI master limitation, ignoring and hoping it will be run as PREOP Transaction error! run OPCODE 0x02 failed spi_byte_program failed during command execution Invalid OPCODE 0x06 due to SPI master limitation, ignoring and hoping it will be run as PREOP Transaction error! run OPCODE 0x02 failed spi_byte_program failed during command execution Invalid OPCODE 0x06 CONFIG_STRICT_DEVMEM is not set in my kernel. Anything I should try out? -- Ticket URL: <http://tracker.coreboot.org/trac/coreboot/ticket/144> coreboot <http://www.coreboot.org/>

1 2

[MSRTOOL][PATCH] Add Geode GX2 processor support.
by Nils 15 Jan '10

15 Jan '10

Hello all, The attached patch (for review) brings support for the AMD Geode GX2 processors to Msrtool. It seems to work as i tested it on my Wyse Winterm S50. Signed-off-by: Nils Jacobs <njacobs8(a)hetnet.nl> Msrtool -l -s output(+ File attached): msrtool 4966M Detected system linux: Linux with /dev/cpu/*/msr Detected target geodegx2: AMD Geode(tm) GX2 Detected target cs5536: AMD Geode(tm) CS5536 Thanks,Nils

3 2

Integrated graphics controller on second bus?
by Andrej Skirn 12 Jan '10

12 Jan '10

Hiya again. I've gotten the CompuLab CM-iVCF board (Was: VIA EDEN ESP (C3) + Apollo CLE266(VT8623) + VT8237R + W83627HG) getting to start booting Windows XP (There was data at the address the northbridge code looks for SPD, but closer inspection revealed it was neither SPD nor EDID. I hard-coded the memory initialization, this also solved problem with the romcc compiled code not fitting into the bootblock). Unfortunately, now I can't seem to get the VGA-BIOS/northbridge VGA adapter working. Biggest problem seems to be that the Unichrome device is on second PCI bus, and I can't find any documentation or example on how to configure CoreBoot to probe and activate devices on other buses. In lspci this shows up as device 01:00.0, but the devicemap parser doesn't accept the bus number. I have tried to place it hierachically under AGP Bridge on the first bus, but CoreBoot still parses it as 00:00.0 and doesn't find the correct device. So how do I define a device on second PCI bus for CoreBoot? I am also looking at the vgabios.c code in epia-m board, but notice that it has been disabled (ie. the device initialization functions no longer called). Is there some reason for this? The Wiki still talks about concatenating the VGA BIOS to the image, although the current way seems to be to include it in CBFS. Is there anywhere I can find more information about the best/preferred way to integrate VGA BIOS into CoreBoot?

5 10

Problems porting H8dmr_fam10 to H8qme-2+
by Knut Kujat 05 Jan '10

05 Jan '10

Hi, I did some small changes in Config.lb and Options.lb and then I compiled the H8dmr_fam10 board to flash it in a H8qme-2+ board. And of course the booting fails :(: (split)40K table at =dfff0000 0: mmio_basek=00380000, basek=00400000, limitk=00000000 1: mmio_basek=00380000, basek=00480000, limitk=00000000 PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0 ? VGA: PCI: 00:18.0 (aka node 0) link 2 has VGA device and here it stucks and doesn't continues. I attached several lspci outputs for the h8qme-2+ board and a complete log of the boot process. Has someone an idea what is failing? thanks in advanced, Knut Kujat. 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:1a.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:1a.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:1a.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:1a.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:1a.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:1b.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:1b.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:1b.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:1b.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:1b.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:01.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) 08:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) 08:01.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) 08:02.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) 08:02.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) 0a:03.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 0a:03.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) -+-[0000:08]-+-01.0-[09]-- | +-01.1 Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC [1022:7459] | +-02.0-[0a]--+-03.0 Intel Corporation 82546GB Gigabit Ethernet Controller [8086:1079] | | \-03.1 Intel Corporation 82546GB Gigabit Ethernet Controller [8086:1079] | \-02.1 Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC [1022:7459] \-[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller [10de:0369] +-01.0 nVidia Corporation MCP55 LPC Bridge [10de:0364] +-01.1 nVidia Corporation MCP55 SMBus [10de:0368] +-02.0 nVidia Corporation MCP55 USB Controller [10de:036c] +-02.1 nVidia Corporation MCP55 USB Controller [10de:036d] +-04.0 nVidia Corporation MCP55 IDE [10de:036e] +-05.0 nVidia Corporation MCP55 SATA Controller [10de:037f] +-05.1 nVidia Corporation MCP55 SATA Controller [10de:037f] +-05.2 nVidia Corporation MCP55 SATA Controller [10de:037f] +-06.0-[01]----01.0 ATI Technologies Inc ES1000 [1002:515e] +-0a.0-[02]-- +-0b.0-[03]-- +-0c.0-[04]-- +-0d.0-[05]-- +-0e.0-[06]-- +-0f.0-[07]-- +-18.0 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] +-18.1 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] +-18.2 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] +-18.3 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] +-18.4 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] +-19.0 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] +-19.1 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] +-19.2 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] +-19.3 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] +-19.4 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] +-1a.0 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] +-1a.1 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] +-1a.2 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] +-1a.3 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] +-1a.4 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] +-1b.0 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200] +-1b.1 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201] +-1b.2 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202] +-1b.3 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203] \-1b.4 Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204] 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at cc00 [size=64] Region 4: I/O ports at 2d00 [size=64] Region 5: I/O ports at 2e00 [size=64] Capabilities: <access denied> Kernel driver in use: nForce2_smbus 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) (prog-if 10 [OHCI]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 22 Region 0: Memory at dfebf000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci_hcd 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 23 Region 0: Memory at dfebec00 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at ffa0 [size=16] Capabilities: <access denied> Kernel driver in use: pata_amd 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at c480 [size=8] Region 1: I/O ports at c400 [size=4] Region 2: I/O ports at c080 [size=8] Region 3: I/O ports at c000 [size=4] Region 4: I/O ports at bc00 [size=16] Region 5: Memory at dfebd000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: sata_nv 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 20 Region 0: I/O ports at b880 [size=8] Region 1: I/O ports at b800 [size=4] Region 2: I/O ports at b480 [size=8] Region 3: I/O ports at b400 [size=4] Region 4: I/O ports at b080 [size=16] Region 5: Memory at dfebc000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: sata_nv 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 23 Region 0: I/O ports at b000 [size=8] Region 1: I/O ports at ac00 [size=4] Region 2: I/O ports at a880 [size=8] Region 3: I/O ports at a800 [size=4] Region 4: I/O ports at a480 [size=16] Region 5: Memory at dfebb000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: sata_nv 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dff00000-dfffffff Prefetchable memory behind bridge: d0000000-d7ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:1a.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:1a.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1b.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:1b.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1b.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1b.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:1b.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 01:01.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA controller]) Subsystem: Super Micro Computer Inc Device 1311 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at d000 [size=256] Region 2: Memory at dfff0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at dff00000 [disabled] [size=128K] Capabilities: <access denied> 08:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Bus: primary=08, secondary=09, subordinate=09, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 08:01.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) (prog-if 10 [IO-APIC]) Subsystem: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at cfeff000 (64-bit, non-prefetchable) [size=4K] 08:02.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: cff00000-cfffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 08:02.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 12) (prog-if 10 [IO-APIC]) Subsystem: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at cfefe000 (64-bit, non-prefetchable) [size=4K] 0a:03.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) Subsystem: Super Micro Computer Inc Device 117a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 47 Region 0: Memory at cffe0000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at ec00 [size=64] Capabilities: <access denied> Kernel driver in use: e1000 0a:03.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) Subsystem: Super Micro Computer Inc Device 117a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 48 Region 0: Memory at cffa0000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at e880 [size=64] Capabilities: <access denied> Kernel driver in use: e1000

4 34

[PATCH] bios_extract
by Rudolf Marek 04 Jan '10

04 Jan '10

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, I think I can CC the coreboot list too. I wanted to extract the Asrock "AMI" ROM found in the 939A785GMH/128M. I had to add following changes to the ami.c 1) there is a flag for uncompressed module 0x90 instead of 0x80 dunno why 2) if the module size in rom > 0xffff some bytes before the structure are used as size, the second number looks like crc maybe. 3) the type of 0x40 and 0x60 is AMD CIM-X but it has compress set, but those modules are not. Signed-off-by: Rudolf Marek <r.marek(a)assembler.cz> Maybe you will need bit to re-arrange patch... Rudolf -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.10 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iEYEARECAAYFAkssJ3gACgkQ3J9wPJqZRNV4OACgnIfGVUivdz2K8HpQhPjCT86r bagAniFQwJ7QKafPiFHc2vQC2SFyODOT =87BW -----END PGP SIGNATURE-----

2 3

Coreboot Support for MSI Board MS-6702E
by freeman2411 03 Jan '10

03 Jan '10

Hi Guys! Can someone help me to get coreboot support for my board MS-6702E? Thank you very much! Greetings freeman2411

4 14

CoreBoot on EPIA 800
by Mike 01 Jan '10

01 Jan '10

Folks, I have an original EPIA 800 motherboard (Via C3 800MHz) that I am interested in trying CoreBoot on. I have been following the suggestion of getting a BIOS Savior for this board but it's a little uncertain which module to go for. I can see that the BIOS is PLCC but the RD1-PL is out of stock and I think I read something about the later replacement models not working with some EPIA boards. Can anyone confirm which BIOS Savior's are available and work with the EPIA 800? Also, can anyone suggest where to get one (I'm in the UK). Cheers, Mike.

2 1

Fwd: [9fans] Broken Hardware List
by ron minnich 31 Dec '09

31 Dec '09

This is really incredible. This is an Intel mainboard and there is something going on that locks out hardware interrupts for 2-5 SECONDS while running FreeBSD. I think the user made the right choice: buy a different mainboard. Another poster reports up to 1 second delays for the BIOS USB stack (mainboard not specified in that case). Finally, I had another report of a different Intel motherboard with an incorrect _MP_ table, which the vendor refused to fix. The fix was the same as the first poster: buy a different mainboard. These are not old mainboards. Every time I start to wonder if coreboot is going to get overtaken by proprietary BIOSes I hear a story of this kind. At that point, I have to wonder why anyone would want a motherboard with a proprietary BIOS, given how bad they are, even today. ron ---------- Forwarded message ---------- From: Lyndon Nerenberg (VE6BBM/VE7TFX) <lyndon(a)orthanc.ca> Date: Wed, Dec 30, 2009 at 7:17 PM Subject: Re: [9fans] Broken Hardware List To: 9fans(a)9fans.net > i think it would be more valuable to explain exactly what's > not working and point to some of the workarounds, if they exist. What's not working is the ACPI component of the BIOS. The P9 boot fails very early on (right after E820 I think). FreeBSD runs, but something in the ACPI code wakes up every couple of seconds and leaps into the ACPI BIOS code. While it's in there it locks out all hardware interrupts for 2-5 seconds, which makes the box pretty much unusable for anything close to interactive work. As to workarounds, I worked around to the computer store and bought a non-Intel motherboard that actually implements Intel's ACPI spec somewhat correctly. I'm not going to spend time I could be billing out to try to fix a completely braindead motherboard that I can replace for what I earn in an hour or two. Shitty hardware like this deserves to die, not get fixed. --lyndon

1 0

KBuild Report [r4994]
by coresystems autobuild service 31 Dec '09

31 Dec '09

[1/116] a-trend/atc-6220 ok. Processing mainboard/a-trend/atc-6220 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [2/116] a-trend/atc-6240 ok. Processing mainboard/a-trend/atc-6240 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [3/116] abit/be6-ii_v2_0 ok. Processing mainboard/abit/be6-ii_v2_0 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [4/116] advantech/pcm-5820 ok. Processing mainboard/advantech/pcm-5820 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [5/116] amd/db800 ok. Processing mainboard/amd/db800 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x4 +CONFIG_IRQ_SLOT_COUNT = 0x6 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [6/116] amd/dbm690t ok. Processing mainboard/amd/dbm690t (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/amd/dbm690t/Config-abuild.lb ok Creating builddir...ok -CONFIG_GFXUMA = 0x1 +CONFIG_GFXUMA = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x100000 +CONFIG_ROM_SIZE = 0x80000 [7/116] amd/norwich ok. Processing mainboard/amd/norwich (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [8/116] amd/pistachio ok. Processing mainboard/amd/pistachio (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/amd/pistachio/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_GFXUMA = 0x1 +CONFIG_GFXUMA = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x0 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x100000 +CONFIG_ROM_SIZE = 0x80000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x1 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [9/116] amd/rumba ok. Processing mainboard/amd/rumba (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [10/116] amd/serengeti_cheetah ok. Processing mainboard/amd/serengeti_cheetah (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/amd/serengeti_cheetah/Config-abuild.lb ok Creating builddir...ok -CONFIG_ACPI_SSDTX_NUM = 0x1 +CONFIG_ACPI_SSDTX_NUM = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [11/116] amd/serengeti_cheetah_fam10 ok. Processing mainboard/amd/serengeti_cheetah_fam10 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/amd/serengeti_cheetah_fam10/Config-abuild.lb ok Creating builddir...ok +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [12/116] arima/hdama ok. Processing mainboard/arima/hdama (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/arima/hdama/Config-abuild.lb ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [13/116] artecgroup/dbe61 ok. Processing mainboard/artecgroup/dbe61 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [14/116] asi/mb_5blgp ok. Processing mainboard/asi/mb_5blgp (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [15/116] asi/mb_5blmp ok. Processing mainboard/asi/mb_5blmp (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_GENERATE_MP_TABLE = 0x0 +CONFIG_GX1_VIDEO = 0x1 +CONFIG_GX1_VIDEOMODE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 +CONFIG_SPLASH_GRAPHIC = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [16/116] asus/a8n_e ok. Processing mainboard/asus/a8n_e (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/asus/a8n_e/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xc8000 +CONFIG_DCACHE_RAM_BASE = 0xcf000 -CONFIG_DCACHE_RAM_SIZE = 0x8000 +CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [17/116] asus/a8v-e_se ok. Processing mainboard/asus/a8v-e_se (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_EPIA_VT8237R_INIT = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_IRQ_SLOT_COUNT = 0xd -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [18/116] asus/m2v-mx_se ok. Processing mainboard/asus/m2v-mx_se (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/asus/m2v-mx_se/Config-abuild.lb ok Creating builddir...ok -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_EPIA_VT8237R_INIT = 0x0 -CONFIG_HAVE_ACPI_RESUME = 0x1 +CONFIG_HAVE_ACPI_RESUME = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_LOW_TABLES = 0x0 +CONFIG_HAVE_LOW_TABLES = 0x1 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x1f00000 +CONFIG_RAMBASE = 0x100000 -CONFIG_RAMTOP = 0x2000000 +CONFIG_RAMTOP = 0x200000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [19/116] asus/mew-am ok. Processing mainboard/asus/mew-am (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [20/116] asus/mew-vm ok. Processing mainboard/asus/mew-vm (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [21/116] asus/p2b-d ok. Processing mainboard/asus/p2b-d (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [22/116] asus/p2b-ds ok. Processing mainboard/asus/p2b-ds (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_AGP_APERTURE_SIZE = 0x4000000 -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_ADDR_BITS = 0x24 +CONFIG_CPU_ADDR_BITS = 0x28 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xc0000 +CONFIG_DCACHE_RAM_BASE = 0xcf000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_ID_SECTION_OFFSET = 0x10 +CONFIG_ID_SECTION_OFFSET = 0x80 -CONFIG_IRQ_SLOT_COUNT = 0x7 +CONFIG_IRQ_SLOT_COUNT = 0xd -CONFIG_LB_CKS_LOC = 0x7e +CONFIG_LB_CKS_LOC = 0x7b -CONFIG_LB_CKS_RANGE_END = 0x7d +CONFIG_LB_CKS_RANGE_END = 0x7a -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x815a -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MEM_TRAIN_SEQ = 0x0 +CONFIG_MEM_TRAIN_SEQ = 0x2 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x40000 +CONFIG_ROM_SIZE = 0x80000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_USE_DCACHE_RAM = 0x0 +CONFIG_USE_DCACHE_RAM = 0x1 -CONFIG_USE_PRINTK_IN_CAR = 0x0 +CONFIG_USE_PRINTK_IN_CAR = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [23/116] asus/p2b-f ok. Processing mainboard/asus/p2b-f (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [24/116] asus/p2b ok. Processing mainboard/asus/p2b (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [25/116] asus/p3b-f ok. Processing mainboard/asus/p3b-f (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [26/116] axus/tc320 ok. Processing mainboard/axus/tc320 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x6 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x6 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [27/116] azza/pt-6ibd ok. Processing mainboard/azza/pt-6ibd (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [28/116] bcom/winnet100 ok. Processing mainboard/bcom/winnet100 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x6 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x6 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [29/116] bcom/winnetp680 ok. Processing mainboard/bcom/winnetp680 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/bcom/winnetp680/Config-abuild.lb ok Creating builddir...ok +CONFIG_CN700_VIDEO_MB_128MB = 0x0 +CONFIG_CN700_VIDEO_MB_16MB = 0x0 +CONFIG_CN700_VIDEO_MB_32MB = 0x1 +CONFIG_CN700_VIDEO_MB_64MB = 0x0 +CONFIG_CN700_VIDEO_MB_8MB = 0x0 +CONFIG_CN700_VIDEO_MB_OFF = 0x0 +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_EPIA_VT8237R_INIT = 0x0 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 [30/116] biostar/m6tba ok. Processing mainboard/biostar/m6tba (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [31/116] broadcom/blast ok. Processing mainboard/broadcom/blast (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x6 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x1 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [32/116] compaq/deskpro_en_sff_p600 ok. Processing mainboard/compaq/deskpro_en_sff_p600 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [33/116] dell/s1850 ok. Processing mainboard/dell/s1850 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x2 -CONFIG_MAX_PHYSICAL_CPUS = 0x1 +CONFIG_MAX_PHYSICAL_CPUS = 0x2 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TTYS0_BAUD = 0x4b00 +CONFIG_TTYS0_BAUD = 0x1c200 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [34/116] digitallogic/adl855pc ok. Processing mainboard/digitallogic/adl855pc (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SMP = 0x0 +CONFIG_SMP = 0x1 -CONFIG_UDELAY_IO = 0x1 +CONFIG_UDELAY_IO = 0x0 -CONFIG_UDELAY_TSC = 0x0 +CONFIG_UDELAY_TSC = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [35/116] digitallogic/msm586seg ok. Processing mainboard/digitallogic/msm586seg (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/digitallogic/msm586seg/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_AMD_SC520 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x80000 +CONFIG_ROM_SIZE = 0x40000 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_UDELAY_LAPIC = 0x0 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [36/116] digitallogic/msm800sev ok. Processing mainboard/digitallogic/msm800sev (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x9 +CONFIG_IRQ_SLOT_COUNT = 0x7 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [37/116] eaglelion/5bcm ok. Processing mainboard/eaglelion/5bcm (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_GX1_VIDEO = 0x1 +CONFIG_GX1_VIDEOMODE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 +CONFIG_SPLASH_GRAPHIC = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [38/116] emulation/qemu-x86 ok. Processing mainboard/emulation/qemu-x86 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/emulation/qemu-x86/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_EMULATION_QEMU_X86 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0x8f000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_UDELAY_LAPIC = 0x0 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [39/116] gigabyte/ga-6bxc ok. Processing mainboard/gigabyte/ga-6bxc (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x6 +CONFIG_IRQ_SLOT_COUNT = 0x5 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [40/116] gigabyte/ga_2761gxdk ok. Processing mainboard/gigabyte/ga_2761gxdk (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/gigabyte/ga_2761gxdk/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MEM_TRAIN_SEQ = 0x2 +CONFIG_MEM_TRAIN_SEQ = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_SMP = 0x0 +CONFIG_SMP = 0x1 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [41/116] gigabyte/m57sli ok. Processing mainboard/gigabyte/m57sli (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/gigabyte/m57sli/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 +CONFIG_HAVE_ACPI_TABLES = 0x1 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MEM_TRAIN_SEQ = 0x2 +CONFIG_MEM_TRAIN_SEQ = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_SUPERIO_ITE_IT8716F_OVERRIDE_FANCTL = 0x1 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [42/116] hp/dl145_g3 ok. Processing mainboard/hp/dl145_g3 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x8 +CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x6 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [43/116] hp/e_vectra_p2706t ok. Processing mainboard/hp/e_vectra_p2706t (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 [44/116] ibm/e325 ok. Processing mainboard/ibm/e325 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_SMP = 0x1 +CONFIG_SMP = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [45/116] ibm/e326 ok. Processing mainboard/ibm/e326 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/ibm/e326/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [46/116] iei/juki-511p ok. Processing mainboard/iei/juki-511p (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/iei/juki-511p/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_GX1_VIDEO = 0x1 +CONFIG_GX1_VIDEOMODE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x0 -CONFIG_HAVE_INIT_TIMER = 0x0 +CONFIG_HAVE_INIT_TIMER = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 +CONFIG_SPLASH_GRAPHIC = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_UDELAY_IO = 0x1 +CONFIG_UDELAY_IO = 0x0 -CONFIG_UDELAY_TSC = 0x0 +CONFIG_UDELAY_TSC = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [47/116] iei/nova4899r ok. Processing mainboard/iei/nova4899r (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_GX1_VIDEO = 0x1 +CONFIG_GX1_VIDEOMODE = 0x0 -CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 +CONFIG_SPLASH_GRAPHIC = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [48/116] iei/pcisa-lx-800-r10 ok. Processing mainboard/iei/pcisa-lx-800-r10 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_INIT_TIMER = 0x0 +CONFIG_HAVE_INIT_TIMER = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_UDELAY_IO = 0x1 +CONFIG_UDELAY_IO = 0x0 -CONFIG_UDELAY_TSC = 0x0 +CONFIG_UDELAY_TSC = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [49/116] intel/d945gclf ok. Processing mainboard/intel/d945gclf (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/intel/d945gclf/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_INTEL_CORE = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xffed8000 +CONFIG_DCACHE_RAM_BASE = 0xffdf8000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x5 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 -CONFIG_GENERATE_ACPI_TABLES = 0x1 +CONFIG_GENERATE_ACPI_TABLES = 0x0 -CONFIG_GFXUMA = 0x1 +CONFIG_GFXUMA = 0x0 -CONFIG_HAVE_ACPI_RESUME = 0x1 +CONFIG_HAVE_ACPI_RESUME = 0x0 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_INIT_TIMER = 0x1 +CONFIG_HAVE_INIT_TIMER = 0x0 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HAVE_SMI_HANDLER = 0x1 +CONFIG_HAVE_SMI_HANDLER = 0x0 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x1 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_ROM_SIZE = 0x80000 +CONFIG_ROM_SIZE = 0x100000 -CONFIG_USE_DCACHE_RAM = 0x1 +CONFIG_USE_DCACHE_RAM = 0x0 [50/116] intel/eagleheights ok. Processing mainboard/intel/eagleheights (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_CORE2 = 0x1 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_ACPI_TABLES = 0x1 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x9 +CONFIG_IRQ_SLOT_COUNT = 0x12 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x8086 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_USE_DCACHE_RAM = 0x1 +CONFIG_USE_DCACHE_RAM = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [51/116] intel/jarrell ok. Processing mainboard/intel/jarrell (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_ATI_RAGE_XL = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x12 +CONFIG_IRQ_SLOT_COUNT = 0x9 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAX_REBOOT_CNT = 0x8 +CONFIG_MAX_REBOOT_CNT = 0x3 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [52/116] intel/mtarvon ok. Processing mainboard/intel/mtarvon (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x5 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LB_CKS_LOC = 0x7e +CONFIG_LB_CKS_LOC = 0x7b -CONFIG_LB_CKS_RANGE_END = 0x7d +CONFIG_LB_CKS_RANGE_END = 0x7a -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x5 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [53/116] intel/truxton ok. Processing mainboard/intel/truxton (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_EP80579 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x5 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LB_CKS_LOC = 0x7e +CONFIG_LB_CKS_LOC = 0x7b -CONFIG_LB_CKS_RANGE_END = 0x7d +CONFIG_LB_CKS_RANGE_END = 0x7a -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x5 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_SMP = 0x1 +CONFIG_SMP = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [54/116] intel/xe7501devkit fail. [55/116] iwill/dk8_htx ok. Processing mainboard/iwill/dk8_htx (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/iwill/dk8_htx/Config-abuild.lb ok Creating builddir...ok -CONFIG_ACPI_SSDTX_NUM = 0x3 +CONFIG_ACPI_SSDTX_NUM = 0x0 -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xc4000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_SIZE = 0xc000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HW_MEM_HOLE_SIZEK = 0x80000 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [56/116] iwill/dk8s2 ok. Processing mainboard/iwill/dk8s2 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 +CONFIG_ATI_RAGE_XL = 0x1 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_IRQ_SLOT_COUNT = 0xc +CONFIG_IRQ_SLOT_COUNT = 0xb -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAX_CPUS = 0x2 +CONFIG_MAX_CPUS = 0x4 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [57/116] iwill/dk8x ok. Processing mainboard/iwill/dk8x (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_IRQ_SLOT_COUNT = 0x9 +CONFIG_IRQ_SLOT_COUNT = 0xb -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAX_CPUS = 0x2 +CONFIG_MAX_CPUS = 0x4 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [58/116] jetway/j7f24 ok. Processing mainboard/jetway/j7f24 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/jetway/j7f24/Config-abuild.lb ok Creating builddir...ok +CONFIG_CN700_VIDEO_MB_128MB = 0x0 +CONFIG_CN700_VIDEO_MB_16MB = 0x0 +CONFIG_CN700_VIDEO_MB_32MB = 0x1 +CONFIG_CN700_VIDEO_MB_64MB = 0x0 +CONFIG_CN700_VIDEO_MB_8MB = 0x0 +CONFIG_CN700_VIDEO_MB_OFF = 0x0 +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_EPIA_VT8237R_INIT = 0x0 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 [59/116] kontron/986lcd-m ok. Processing mainboard/kontron/986lcd-m (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/kontron/986lcd-m/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_INTEL_CORE = 0x1 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x5 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_ACPI_SLIC = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 [60/116] kontron/kt690 ok. Processing mainboard/kontron/kt690 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/kontron/kt690/Config-abuild.lb ok Creating builddir...ok +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_ROM_SIZE = 0x100000 +CONFIG_ROM_SIZE = 0x80000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [61/116] lippert/frontrunner ok. Processing mainboard/lippert/frontrunner (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [62/116] lippert/roadrunner-lx ok. Processing mainboard/lippert/roadrunner-lx (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 -CONFIG_DEBUG = 0x1 +CONFIG_DEBUG = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [63/116] lippert/spacerunner-lx ok. Processing mainboard/lippert/spacerunner-lx (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 -CONFIG_DEBUG = 0x1 +CONFIG_DEBUG = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [64/116] mitac/6513wu ok. Processing mainboard/mitac/6513wu (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [65/116] msi/ms6119 ok. Processing mainboard/msi/ms6119 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [66/116] msi/ms6147 ok. Processing mainboard/msi/ms6147 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [67/116] msi/ms6156 ok. Processing mainboard/msi/ms6156 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [68/116] msi/ms6178 ok. Processing mainboard/msi/ms6178 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_IO = 0x0 +CONFIG_UDELAY_IO = 0x1 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [69/116] msi/ms7135 ok. Processing mainboard/msi/ms7135 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/msi/ms7135/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_DCACHE_RAM_BASE = 0xc8000 +CONFIG_DCACHE_RAM_BASE = 0xcf000 -CONFIG_DCACHE_RAM_SIZE = 0x8000 +CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_MEM_TRAIN_SEQ = 0x2 +CONFIG_MEM_TRAIN_SEQ = 0x0 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [70/116] msi/ms7260 ok. Processing mainboard/msi/ms7260 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/msi/ms7260/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_MEM_TRAIN_SEQ = 0x2 +CONFIG_MEM_TRAIN_SEQ = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [71/116] msi/ms9185 ok. Processing mainboard/msi/ms9185 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/msi/ms9185/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x8 +CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x6 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1022 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [72/116] msi/ms9282 ok. Processing mainboard/msi/ms9282 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/msi/ms9282/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 -CONFIG_ENABLE_APIC_EXT_ID = 0x1 +CONFIG_ENABLE_APIC_EXT_ID = 0x0 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HW_MEM_HOLE_SIZEK = 0x0 +CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x2 -CONFIG_MAX_PHYSICAL_CPUS = 0x2 +CONFIG_MAX_PHYSICAL_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x1 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [73/116] nec/powermate2000 ok. Processing mainboard/nec/powermate2000 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I810_VIDEO_MB_1MB = 0x1 +CONFIG_I810_VIDEO_MB_512KB = 0x0 +CONFIG_I810_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [74/116] newisys/khepri ok. Processing mainboard/newisys/khepri (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x9 +CONFIG_IRQ_SLOT_COUNT = 0xb -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [75/116] nvidia/l1_2pvv ok. Processing mainboard/nvidia/l1_2pvv (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/nvidia/l1_2pvv/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x2 -CONFIG_MAX_PHYSICAL_CPUS = 0x2 +CONFIG_MAX_PHYSICAL_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 [76/116] olpc/btest ok. Processing mainboard/olpc/btest (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [77/116] olpc/rev_a ok. Processing mainboard/olpc/rev_a (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [78/116] pcengines/alix1c ok. Processing mainboard/pcengines/alix1c (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_LX = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [79/116] rca/rm4100 ok. Processing mainboard/rca/rm4100 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/rca/rm4100/Config-abuild.lb ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I830_VIDEO_MB_1MB = 0x0 +CONFIG_I830_VIDEO_MB_512KB = 0x0 +CONFIG_I830_VIDEO_MB_8MB = 0x1 +CONFIG_I830_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [80/116] soyo/sy-6ba-plus-iii ok. Processing mainboard/soyo/sy-6ba-plus-iii (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [81/116] sunw/ultra40 ok. Processing mainboard/sunw/ultra40 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_ENABLE_APIC_EXT_ID = 0x1 +CONFIG_ENABLE_APIC_EXT_ID = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [82/116] supermicro/h8dme ok. Processing mainboard/supermicro/h8dme (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/supermicro/h8dme/Config-abuild.lb ok Creating builddir...ok -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_LOW_TABLES = 0x0 +CONFIG_HAVE_LOW_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 [83/116] supermicro/h8dmr ok. Processing mainboard/supermicro/h8dmr (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/supermicro/h8dmr/Config-abuild.lb ok Creating builddir...ok +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_ROM_SIZE = 0x100000 +CONFIG_ROM_SIZE = 0x80000 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 [84/116] supermicro/h8dmr_fam10 fail. [85/116] supermicro/x6dai_g ok. Processing mainboard/supermicro/x6dai_g (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [86/116] supermicro/x6dhe_g ok. Processing mainboard/supermicro/x6dhe_g (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [87/116] supermicro/x6dhe_g2 ok. Processing mainboard/supermicro/x6dhe_g2 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [88/116] supermicro/x6dhr_ig ok. Processing mainboard/supermicro/x6dhr_ig (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [89/116] supermicro/x6dhr_ig2 ok. Processing mainboard/supermicro/x6dhr_ig2 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [90/116] technexion/tim5690 ok. Processing mainboard/technexion/tim5690 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/technexion/tim5690/Config-abuild.lb ok Creating builddir...ok +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 [91/116] technexion/tim8690 ok. Processing mainboard/technexion/tim8690 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/technexion/tim8690/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x8 -CONFIG_GFXUMA = 0x1 +CONFIG_GFXUMA = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 -CONFIG_HAVE_OPTION_TABLE = 0x0 +CONFIG_HAVE_OPTION_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x0 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x1 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 [92/116] technologic/ts5300 ok. Processing mainboard/technologic/ts5300 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/technologic/ts5300/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_AMD_SC520 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x20000 +CONFIG_ROM_SIZE = 0x40000 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 -CONFIG_TTYS0_BASE = 0x2f8 +CONFIG_TTYS0_BASE = 0x3f8 +CONFIG_UDELAY_LAPIC = 0x0 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [93/116] televideo/tc7020 ok. Processing mainboard/televideo/tc7020 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_AMD_GX1 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x6 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x6 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [94/116] thomson/ip1000 ok. Processing mainboard/thomson/ip1000 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/thomson/ip1000/Config-abuild.lb ok Creating builddir...ok -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 +CONFIG_I830_VIDEO_MB_1MB = 0x0 +CONFIG_I830_VIDEO_MB_512KB = 0x0 +CONFIG_I830_VIDEO_MB_8MB = 0x1 +CONFIG_I830_VIDEO_MB_OFF = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 +CONFIG_MMX = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [95/116] tyan/s1846 ok. Processing mainboard/tyan/s1846 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_INTEL_SLOT_2 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [96/116] tyan/s2735 ok. Processing mainboard/tyan/s2735 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_MOVNTI = 0x1 +CONFIG_HAVE_MOVNTI = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 +CONFIG_MMX = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 -CONFIG_USE_PRINTK_IN_CAR = 0x1 +CONFIG_USE_PRINTK_IN_CAR = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [97/116] tyan/s2850 ok. Processing mainboard/tyan/s2850 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [98/116] tyan/s2875 ok. Processing mainboard/tyan/s2875 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [99/116] tyan/s2880 ok. Processing mainboard/tyan/s2880 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0xd +CONFIG_IRQ_SLOT_COUNT = 0x9 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAX_CPUS = 0x2 +CONFIG_MAX_CPUS = 0x4 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [100/116] tyan/s2881 ok. Processing mainboard/tyan/s2881 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [101/116] tyan/s2882 ok. Processing mainboard/tyan/s2882 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0xa -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0xf +CONFIG_IRQ_SLOT_COUNT = 0x9 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [102/116] tyan/s2885 ok. Processing mainboard/tyan/s2885 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_ENABLE_APIC_EXT_ID = 0x1 +CONFIG_ENABLE_APIC_EXT_ID = 0x0 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0xb +CONFIG_IRQ_SLOT_COUNT = 0x9 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [103/116] tyan/s2891 ok. Processing mainboard/tyan/s2891 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/tyan/s2891/Config-abuild.lb ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_ROM_SIZE = 0x80000 +CONFIG_ROM_SIZE = 0x100000 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 [104/116] tyan/s2892 ok. Processing mainboard/tyan/s2892 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/tyan/s2892/Config-abuild.lb ok Creating builddir...ok -CONFIG_APIC_ID_OFFSET = 0x0 +CONFIG_APIC_ID_OFFSET = 0x10 -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 [105/116] tyan/s2895 ok. Processing mainboard/tyan/s2895 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/tyan/s2895/Config-abuild.lb ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_BASE = 0xcf000 +CONFIG_DCACHE_RAM_BASE = 0xc8000 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DIMM_SUPPORT = 0x108 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SERIAL_CPU_INIT = 0x0 +CONFIG_SERIAL_CPU_INIT = 0x1 [106/116] tyan/s2912 ok. Processing mainboard/tyan/s2912 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/tyan/s2912/Config-abuild.lb ok Creating builddir...ok -CONFIG_ACPI_SSDTX_NUM = 0x3 +CONFIG_ACPI_SSDTX_NUM = 0x0 -CONFIG_APIC_ID_OFFSET = 0x10 +CONFIG_APIC_ID_OFFSET = 0x16 -CONFIG_HAVE_FALLBACK_BOOT = 0x1 +CONFIG_HAVE_FALLBACK_BOOT = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HEAP_SIZE = 0x8000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_MAX_CPUS = 0x4 +CONFIG_MAX_CPUS = 0x2 -CONFIG_MAX_PHYSICAL_CPUS = 0x2 +CONFIG_MAX_PHYSICAL_CPUS = 0x1 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 -CONFIG_SERIAL_CPU_INIT = 0x1 +CONFIG_SERIAL_CPU_INIT = 0x0 -CONFIG_USE_FALLBACK_IMAGE = 0x1 +CONFIG_USE_FALLBACK_IMAGE = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 -CONFIG_WAIT_BEFORE_CPUS_INIT = 0x1 +CONFIG_WAIT_BEFORE_CPUS_INIT = 0x0 [107/116] tyan/s2912_fam10 fail. [108/116] tyan/s4880 ok. Processing mainboard/tyan/s4880 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_ENABLE_APIC_EXT_ID = 0x1 +CONFIG_ENABLE_APIC_EXT_ID = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x16 +CONFIG_IRQ_SLOT_COUNT = 0xb -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_MAX_CPUS = 0x8 +CONFIG_MAX_CPUS = 0x4 -CONFIG_MAX_PHYSICAL_CPUS = 0x4 +CONFIG_MAX_PHYSICAL_CPUS = 0x2 -CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 -CONFIG_RAMBASE = 0x4000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [109/116] tyan/s4882 ok. Processing mainboard/tyan/s4882 (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok -CONFIG_CPU_SOCKET_TYPE = 0x10 +CONFIG_CPU_SOCKET_TYPE = 0x0 -CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x0 +CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x1000 -CONFIG_DIMM_SUPPORT = 0x108 -CONFIG_ENABLE_APIC_EXT_ID = 0x1 +CONFIG_ENABLE_APIC_EXT_ID = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HT_CHAIN_END_UNITID_BASE = 0x20 +CONFIG_HT_CHAIN_END_UNITID_BASE = 0x0 -CONFIG_HT_CHAIN_UNITID_BASE = 0x1 +CONFIG_HT_CHAIN_UNITID_BASE = 0x0 -CONFIG_IRQ_SLOT_COUNT = 0x16 +CONFIG_IRQ_SLOT_COUNT = 0xb -CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x0 +CONFIG_K8_HT_FREQ_1G_SUPPORT = 0x1 -CONFIG_MAX_CPUS = 0x8 +CONFIG_MAX_CPUS = 0x4 -CONFIG_MAX_PHYSICAL_CPUS = 0x4 +CONFIG_MAX_PHYSICAL_CPUS = 0x2 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_RAMBASE = 0x2000 +CONFIG_RAMBASE = 0x100000 -CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x0 +CONFIG_SB_HT_CHAIN_ON_BUS0 = 0x2 -CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x1 +CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [110/116] via/epia-cn ok. Processing mainboard/via/epia-cn (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/epia-cn/Config-abuild.lb ok Creating builddir...ok +CONFIG_CN700_VIDEO_MB_128MB = 0x0 +CONFIG_CN700_VIDEO_MB_16MB = 0x0 +CONFIG_CN700_VIDEO_MB_32MB = 0x1 +CONFIG_CN700_VIDEO_MB_64MB = 0x0 +CONFIG_CN700_VIDEO_MB_8MB = 0x0 +CONFIG_CN700_VIDEO_MB_OFF = 0x0 +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_EPIA_VT8237R_INIT = 0x0 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 [111/116] via/epia-m ok. Processing mainboard/via/epia-m (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/epia-m/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_VIA_C3 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 [112/116] via/epia-m700 ok. Processing mainboard/via/epia-m700 (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/epia-m700/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DCACHE_RAM_SIZE = 0x2000 +CONFIG_DCACHE_RAM_SIZE = 0x8000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x0 -CONFIG_HEAP_SIZE = 0x5000 +CONFIG_HEAP_SIZE = 0x4000 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1019 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_USE_DCACHE_RAM = 0x1 +CONFIG_USE_DCACHE_RAM = 0x0 [113/116] via/epia-n ok. Processing mainboard/via/epia-n (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/epia-n/Config-abuild.lb ok Creating builddir...ok +CONFIG_CN400_VIDEO_MB_128MB = 0x0 +CONFIG_CN400_VIDEO_MB_16MB = 0x0 +CONFIG_CN400_VIDEO_MB_32MB = 0x1 +CONFIG_CN400_VIDEO_MB_64MB = 0x0 +CONFIG_CN400_VIDEO_MB_8MB = 0x0 +CONFIG_CN400_VIDEO_MB_OFF = 0x0 +CONFIG_CPU_VIA_C3 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_ACPI_TABLES = 0x1 +CONFIG_HAVE_HIGH_TABLES = 0x0 -CONFIG_HAVE_MAINBOARD_RESOURCES = 0x1 +CONFIG_HAVE_MAINBOARD_RESOURCES = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_SMP = 0x1 +CONFIG_SMP = 0x0 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0 [114/116] via/epia ok. Processing mainboard/via/epia (i386: ok, we're amd64 with a cross compiler) Creating config file... ok Creating builddir...ok +CONFIG_CPU_VIA_C3 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x7 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 -CONFIG_HAVE_INIT_TIMER = 0x0 +CONFIG_HAVE_INIT_TIMER = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_REALMODE = 0x1 +CONFIG_PCI_OPTION_ROM_RUN_X86EMU = 0x0 +CONFIG_PCI_OPTION_ROM_RUN_YABEL = 0x0 -CONFIG_PCI_ROM_RUN = 0x0 +CONFIG_PCI_ROM_RUN = 0x1 -CONFIG_UDELAY_IO = 0x1 +CONFIG_UDELAY_IO = 0x0 -CONFIG_VGA_ROM_RUN = 0x0 +CONFIG_VGA_ROM_RUN = 0x1 [115/116] via/pc2500e ok. Processing mainboard/via/pc2500e (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/pc2500e/Config-abuild.lb ok Creating builddir...ok +CONFIG_CN700_VIDEO_MB_128MB = 0x0 +CONFIG_CN700_VIDEO_MB_16MB = 0x0 +CONFIG_CN700_VIDEO_MB_32MB = 0x1 +CONFIG_CN700_VIDEO_MB_64MB = 0x0 +CONFIG_CN700_VIDEO_MB_8MB = 0x0 +CONFIG_CN700_VIDEO_MB_OFF = 0x0 +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DCACHE_RAM_BASE = 0xc0000 -CONFIG_DCACHE_RAM_SIZE = 0x1000 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x9 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_EPIA_VT8237R_INIT = 0x0 +CONFIG_FALLBACK_SIZE = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x1 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x9 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x0 +CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 0x1 -CONFIG_USE_OPTION_TABLE = 0x1 +CONFIG_USE_OPTION_TABLE = 0x0 [116/116] via/vt8454c ok. Processing mainboard/via/vt8454c (i386: ok, we're amd64 with a cross compiler) Using existing test target /srv/svn/coreboot-extra/tmp/coreboot-v2-4994/targets/via/vt8454c/Config-abuild.lb ok Creating builddir...ok +CONFIG_CPU_VIA_C7 = 0x1 -CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x5 +CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 0x8 +CONFIG_HAVE_ACPI_TABLES = 0x1 -CONFIG_HAVE_HARD_RESET = 0x1 +CONFIG_HAVE_HARD_RESET = 0x0 +CONFIG_HAVE_HIGH_TABLES = 0x0 +CONFIG_HAVE_MP_TABLE = 0x1 +CONFIG_HAVE_PIRQ_TABLE = 0x1 -CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x1 +CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT = 0x0 -CONFIG_IOAPIC = 0x1 +CONFIG_IOAPIC = 0x0 -CONFIG_LOGICAL_CPUS = 0x0 +CONFIG_LOGICAL_CPUS = 0x1 -CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x0 +CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1019 -CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x5 +CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 0x8 -CONFIG_ROM_SIZE = 0x80000 +CONFIG_ROM_SIZE = 0x100000 -CONFIG_SMP = 0x1 +CONFIG_SMP = 0x0 -CONFIG_UDELAY_TSC = 0x1 +CONFIG_UDELAY_TSC = 0x0 -CONFIG_USE_DCACHE_RAM = 0x1 +CONFIG_USE_DCACHE_RAM = 0x0 -CONFIG_WRITE_HIGH_TABLES = 0x1 +CONFIG_WRITE_HIGH_TABLES = 0x0

1 0

build service results for r4994
by coreboot information 31 Dec '09

31 Dec '09

Dear coreboot readers! This is the automatic build system of coreboot. The developer "oxygene" checked in revision 4994 to the coreboot repository. This caused the following changes: Change Log: romcc: - Set __PRE_RAM__ define per default - Properly handle ignored (#ifdef'd out) #include lines amd/serengeti_cheetah_fam10: - write ACPI files to $(obj) instead of the top dir (alias $(CURDIR)) tinybootblock: - provide a way to define code that should be added to the bootblock, to map the entire ROM for use by CBFS amd/model_fxx, amd/model_10xxx: - add CONFIG_SSE walkcbfs.S: - eliminate the use of two registers, to make space for romcc to wiggle amd/serengeti_cheetah_fam10: - use the enable_rom framework. not entirely functional yet Boot-tested on emulation/qemu-x86 Build-tested on amd/serengeti_cheetah_fam10 amd/serengeti_cheetah_fam10 fails in amdht/ somewhere, but builds Signed-off-by: Patrick Georgi <patrick.georgi(a)coresystems.de> Acked-by: Ronald G. Minnich <rminnich(a)gmail.com> Build Log: Compilation of intel:xe7501devkit has been broken See the error log at http://qa.coreboot.org/log_buildbrd.php?revision=4994&device=xe7501devkit&v… If something broke during this checkin please be a pain in oxygene's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, coreboot automatic build system

1 0

← Newer
1
2
3
4
5
6
7
8
...
17
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot December 2009