r1138 - in coreboot-v3: . mainboard/artecgroup mainboard/artecgroup/dbe61 mainboard/artecgroup/dbe62 southbridge/amd/cs5536
Author: mraudsepp Date: 2009-02-23 19:42:44 +0100 (Mon, 23 Feb 2009) New Revision: 1138
Added: coreboot-v3/southbridge/amd/cs5536/nand.c Modified: coreboot-v3/Kconfig coreboot-v3/mainboard/artecgroup/Kconfig coreboot-v3/mainboard/artecgroup/dbe61/dts coreboot-v3/mainboard/artecgroup/dbe62/dts coreboot-v3/southbridge/amd/cs5536/Makefile coreboot-v3/southbridge/amd/cs5536/cs5536.c coreboot-v3/southbridge/amd/cs5536/cs5536.h coreboot-v3/southbridge/amd/cs5536/nand Log: cs5536: Make NAND code optional and implement timing setting
The reset value for NAND timings is the slowest possible for Flash interface. Implement optionally setting it to a different value inside the NAND device. Set it to appropriate values for Artec Group DBE61 and DBE62. This results in a roughly two times quicker read time as measured by hdparm for these boards.
Because we can not cast to southbridge_amd_cs5536_nand_config if the board dts does not have an entry for the NAND device, this change proposes a method for reasonably clean way to only optionally compile in support for certain devices: If a board wants to support an optional device, its Kconfig entry can select that configuration. If it's optional even across the same board, it can expose a subconfig option of the board, that describes it and if chosen selects the device config. The source code for that device is conditionally compiled only if the Kconfig option gets enabled by the configuration for the board. A requirement is that if the board configuration can enable a device, it is contained in the boards dts file as well.
A perhaps better long-term alternative for this could be making dtc generate preprocessor definitions for each device_configuration struct that it creates. Then the source code file is always enabled, but that file can be wrapped around a simple #ifdef check in its entirety.
Conversion to the alternative approach from the short-term Kconfig approach proposed here should be relatively easy, as to not block inclusion of the Kconfig approach in the short term.
Signed-off-by: Mart Raudsepp mart.raudsepp@artecdesign.ee Acked-by: Marc Jones marcj303@gmail.com
Modified: coreboot-v3/Kconfig =================================================================== --- coreboot-v3/Kconfig 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/Kconfig 2009-02-23 18:42:44 UTC (rev 1138) @@ -163,6 +163,11 @@ config SUPERIO_VIA_VT1211 boolean
+# Other devices that may be optional for a board: +config DEVICE_AMD_CS5536_NAND + select SOUTHBRIDGE_AMD_CS5536 + boolean + menu "Payload"
config PAYLOAD_ELF_LOADER
Modified: coreboot-v3/mainboard/artecgroup/Kconfig =================================================================== --- coreboot-v3/mainboard/artecgroup/Kconfig 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/mainboard/artecgroup/Kconfig 2009-02-23 18:42:44 UTC (rev 1138) @@ -29,6 +29,7 @@ select CPU_AMD_GEODELX select NORTHBRIDGE_AMD_GEODELX select SOUTHBRIDGE_AMD_CS5536 + select DEVICE_AMD_CS5536_NAND select PIRQ_TABLE help Artec Group DBE61 ThinCan, also known as Linutop 1. @@ -39,6 +40,7 @@ select CPU_AMD_GEODELX select NORTHBRIDGE_AMD_GEODELX select SOUTHBRIDGE_AMD_CS5536 + select DEVICE_AMD_CS5536_NAND select PIRQ_TABLE help Artec Group DBE62 ThinCan.
Modified: coreboot-v3/mainboard/artecgroup/dbe61/dts =================================================================== --- coreboot-v3/mainboard/artecgroup/dbe61/dts 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/mainboard/artecgroup/dbe61/dts 2009-02-23 18:42:44 UTC (rev 1138) @@ -109,8 +109,11 @@ /* USB Port Power Handling setting. */ pph = "0xf5"; }; - pci@f,1 { + pci@f,1 { /* NAND Flash */ /config/("southbridge/amd/cs5536/nand"); + /* Timings */ + nandf_data = "0x01200120"; + nandf_ctl = "0x00000120"; }; }; };
Modified: coreboot-v3/mainboard/artecgroup/dbe62/dts =================================================================== --- coreboot-v3/mainboard/artecgroup/dbe62/dts 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/mainboard/artecgroup/dbe62/dts 2009-02-23 18:42:44 UTC (rev 1138) @@ -63,8 +63,11 @@ /* USB Port Power Handling setting. */ pph = "0xf5"; }; - pci@f,1 { + pci@f,1 { /* NAND Flash */ /config/("southbridge/amd/cs5536/nand"); + /* Timings */ + nandf_data = "0x01200120"; + nandf_ctl = "0x00000120"; }; }; };
Modified: coreboot-v3/southbridge/amd/cs5536/Makefile =================================================================== --- coreboot-v3/southbridge/amd/cs5536/Makefile 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/southbridge/amd/cs5536/Makefile 2009-02-23 18:42:44 UTC (rev 1138) @@ -23,6 +23,10 @@
STAGE2_CHIPSET_SRC += $(src)/southbridge/amd/cs5536/cs5536.c
+ifeq ($(CONFIG_DEVICE_AMD_CS5536_NAND),y) +STAGE2_CHIPSET_SRC += $(src)/southbridge/amd/cs5536/nand.c +endif + ifeq ($(CONFIG_PIRQ_TABLE),y) STAGE2_CHIPSET_SRC += $(src)/southbridge/amd/cs5536/irq_tables.c endif
Modified: coreboot-v3/southbridge/amd/cs5536/cs5536.c =================================================================== --- coreboot-v3/southbridge/amd/cs5536/cs5536.c 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/southbridge/amd/cs5536/cs5536.c 2009-02-23 18:42:44 UTC (rev 1138) @@ -88,7 +88,7 @@ * bits 24 -> 30 reserved and set to zero * bit 31 triggers the config cycle */ -static void hide_vpci(u32 vpci_devid) +void hide_vpci(u32 vpci_devid) { printk(BIOS_DEBUG, "Hiding VPCI device: 0x%08X (%02x:%02x.%01x)\n", vpci_devid, (vpci_devid >> 16) & 0xff, @@ -98,43 +98,6 @@ }
/** - * Enables the FLASH PCI header when NAND device existing in mainboard device - * tree. Used when the mainboard has a FLASH part instead of an IDE drive and - * that fact is expressed in the mainboard device tree. - * Must be called after VSA init but before PCI scans to enable the flash - * PCI device header early enough - that is .phase2_fixup of the device. - * - * @param dev The device. - */ -static void nand_phase2(struct device *dev) -{ - if (dev->enabled) { - /* Tell VSA to use FLASH PCI header. Not IDE header. */ - hide_vpci(0x800079C4); - } -} - -static void nand_read_resources(struct device *dev) -{ - pci_dev_read_resources(dev); - - /* All memory accesses in the range of 0xF0000000 - 0xFFFFFFFF routed to - * Diverse Integration Logic (DIVIL) get always sent to the device inside - * DIVIL as set in DIVIL_BALL_OPTS PRI_BOOT_LOC and SEC_BOOT_LOC bits - * (see CS5536 data book chapter 6.6.2.10 DIVIL_BALL_OPTS PRI_BOOT_LOC - * description). - * The virtual PCI address limit test gives us a false upper limit of - * 0xFFFFFFFF for this device, but we do not want NAND Flash to be using - * memory addresses 0xF0000000 and above as those accesses would end up - * somewhere else instead. Therefore if VSA2 gave us a MMIO resource for - * NAND Flash, patch this (fixed) resources higher bound to 0xEFFFFFFF. - */ - if ((dev->resources >= 1) && (dev->resource[0].flags & IORESOURCE_MEM) && - (dev->resource[0].limit > 0xefffffff)) - dev->resource[0].limit = 0xefffffff; -} - -/** * Power button setup. * * Setup GPIO24, it is the external signal for CS5536 vsb_work_aux which @@ -749,17 +712,3 @@ .phase6_init = ide_init, .ops_pci = &pci_dev_ops_pci, }; - -struct device_operations cs5536_nand = { - .id = {.type = DEVICE_ID_PCI, - {.pci = {.vendor = PCI_VENDOR_ID_AMD, - .device = PCI_DEVICE_ID_AMD_CS5536_FLASH}}}, - .constructor = default_device_constructor, - .phase2_fixup = nand_phase2, - .phase3_scan = 0, - .phase4_read_resources = nand_read_resources, - .phase4_set_resources = pci_set_resources, - .phase5_enable_resources = pci_dev_enable_resources, - .phase6_init = 0, /* No Option ROMs */ - .ops_pci = &pci_dev_ops_pci, -};
Modified: coreboot-v3/southbridge/amd/cs5536/cs5536.h =================================================================== --- coreboot-v3/southbridge/amd/cs5536/cs5536.h 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/southbridge/amd/cs5536/cs5536.h 2009-02-23 18:42:44 UTC (rev 1138) @@ -445,5 +445,6 @@ void cs5536_disable_internal_uart(void); void cs5536_setup_onchipuart(int uart); void cs5536_stage1(void); +void hide_vpci(u32 vpci_devid);
#endif /* SOUTHBRIDGE_AMD_CS5536_CS5536_H */
Modified: coreboot-v3/southbridge/amd/cs5536/nand =================================================================== --- coreboot-v3/southbridge/amd/cs5536/nand 2009-02-21 17:28:24 UTC (rev 1137) +++ coreboot-v3/southbridge/amd/cs5536/nand 2009-02-23 18:42:44 UTC (rev 1138) @@ -20,4 +20,8 @@
{ device_operations = "cs5536_nand"; + + /* NAND timings per data book and NAND chip on board. 0x0 leaves to reset value. */ + nandf_data = "0x0"; + nandf_ctl = "0x0"; };
Added: coreboot-v3/southbridge/amd/cs5536/nand.c =================================================================== --- coreboot-v3/southbridge/amd/cs5536/nand.c (rev 0) +++ coreboot-v3/southbridge/amd/cs5536/nand.c 2009-02-23 18:42:44 UTC (rev 1138) @@ -0,0 +1,93 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2009 Artec Design LLC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console.h> +#include <device/pci.h> +#include <msr.h> +#include <statictree.h> +#include "cs5536.h" + +/** + * Enables the FLASH PCI header when NAND device existing in mainboard device + * tree. Used when the mainboard has a FLASH part instead of an IDE drive and + * that fact is expressed in the mainboard device tree. + * Must be called after VSA init but before PCI scans to enable the flash + * PCI device header early enough - that is .phase2_fixup of the device. + * + * @param dev The device. + */ +static void nand_phase2(struct device *dev) +{ + if (dev->enabled) { + struct southbridge_amd_cs5536_nand_config *nand; + struct msr msr; + + /* Set up timings */ + nand = (struct southbridge_amd_cs5536_nand_config *)dev->device_configuration; + msr.hi = 0x0; + + if (nand->nandf_data) { + msr.lo = nand->nandf_data; + wrmsr(MDD_NANDF_DATA, msr); + printk(BIOS_DEBUG, "NANDF_DATA set to 0x%08x\n", msr.lo); + } + if (nand->nandf_ctl) { + msr.lo = nand->nandf_ctl; + wrmsr(MDD_NANDF_CTL, msr); + printk(BIOS_DEBUG, "NANDF_CTL set to 0x%08x\n", msr.lo); + } + + /* Tell VSA to use FLASH PCI header. Not IDE header. */ + hide_vpci(0x800079C4); + } +} + +static void nand_read_resources(struct device *dev) +{ + pci_dev_read_resources(dev); + + /* All memory accesses in the range of 0xF0000000 - 0xFFFFFFFF routed to + * Diverse Integration Logic (DIVIL) get always sent to the device inside + * DIVIL as set in DIVIL_BALL_OPTS PRI_BOOT_LOC and SEC_BOOT_LOC bits + * (see CS5536 data book chapter 6.6.2.10 DIVIL_BALL_OPTS PRI_BOOT_LOC + * description). + * The virtual PCI address limit test gives us a false upper limit of + * 0xFFFFFFFF for this device, but we do not want NAND Flash to be using + * memory addresses 0xF0000000 and above as those accesses would end up + * somewhere else instead. Therefore if VSA2 gave us a MMIO resource for + * NAND Flash, patch this (fixed) resources higher bound to 0xEFFFFFFF. + */ + if ((dev->resources >= 1) && (dev->resource[0].flags & IORESOURCE_MEM) && + (dev->resource[0].limit > 0xefffffff)) + dev->resource[0].limit = 0xefffffff; +} + +struct device_operations cs5536_nand = { + .id = {.type = DEVICE_ID_PCI, + {.pci = {.vendor = PCI_VENDOR_ID_AMD, + .device = PCI_DEVICE_ID_AMD_CS5536_FLASH}}}, + .constructor = default_device_constructor, + .phase2_fixup = nand_phase2, + .phase3_scan = 0, + .phase4_read_resources = nand_read_resources, + .phase4_set_resources = pci_set_resources, + .phase5_enable_resources = pci_dev_enable_resources, + .phase6_init = 0, /* No Option ROMs */ + .ops_pci = &pci_dev_ops_pci, +};
-
svn＠coreboot.org