Hi Zheng,
Schematic is simple and OK. I assume you are trying to run Wolf VPXxx-E8860-xxxx or similar GPU borad. You can't do much there if there is a hardware problem but it is most possibly a software setup problem.
VPX does not have incomming clock so it is by default in async_clock mode. The question is did you allowed that mode on the main board side?
Asynchronous clock mode is not default mode for a motherboard. Check if the mode is allowed. Second, check if the other PCIe device can work on the motherboard PCIe slot.
Regards, Predrag
On Fri, Jan 13, 2017 at 6:44 AM, Zheng Bao fishbaoz@hotmail.com wrote:
Here is the ref clk part. Please review.
No refclk routes to VPX connector.
Thanks.
Zheng
*From:* Predrag Vidic pvidic@gmail.com *Sent:* Thursday, January 12, 2017 6:53 PM *To:* Zheng Bao *Cc:* Zoran Stojsavljevic; coreboot@coreboot.org
*Subject:* Re: [coreboot] Question about PCIe separate reference clock
Hi Zheng,
Without knowing the particular solution for the PCIe transmitter you have on your board, I'd check refclk pins on your design for the proper termination. The problem can be in irregular readings from the pins.
Reragds, Predrag
On Thu, Jan 12, 2017 at 3:26 PM, Zheng Bao fishbaoz@hotmail.com wrote:
Q: do you use local xtal attached to Si52111-B5 to generate local PCIe 25MHz clock?
Zheng: yes
Q: If you dothis, my next question is how you synchronize these two clocks: Local PCIe 25 MHz and common reference clock from CPU?
Zheng: We do NOT sync these two.
Q: Since these two clocks, as I understand above scenario, are asynchronous to each other?!
Zheng: yes. Asynchronous.
The VPX connector does not have a PCIe ref clock signal, so we can not send CPU PCIe ref clock to
device. The PCIe spec says if the separate refclk on devices should be 100MHz ± 300PPM, with SSC
off. We believe our board meet this requirement. So we doubt the problem lies in PCI configration space.
Zheng
*From:* Zoran Stojsavljevic zoran.stojsavljevic@gmail.com *Sent:* Thursday, January 12, 2017 9:22 AM *To:* Zheng Bao; Predrag Vidic *Cc:* coreboot@coreboot.org *Subject:* Re: [coreboot] Question about PCIe separate reference clock
Hello Zheng,
For decades, I've been FW/SW engineer, but I do understand a little bit of a HW. I have looked into the Si52111-B5 data sheet for clarification.
My problem here is to understand, your use case: do you use local xtal attached to Si52111-B5 to generate local PCIe 25MHz clock? If you do this, my next question is how you synchronize these two clocks: Local PCIe 25 MHz and common reference clock from CPU?
Since these two clocks, as I understand above scenario, are asynchronous to each other?!
Please, clarify for us your use case.
Thank you, Zoran _______
On 1/12/17, Zheng Bao fishbaoz@hotmail.com wrote:
Our VPX design uses separate reference clock source, which is
Si52111-B5 (No
spread), instead of common ref clock from CPU. Now The system is unstable. Reading PCIE configuration space is unstable too. (If we add some fly wire to make it work with common ref clock, the system becomes stable.)
(abstracted from PCIe spec: 12 Slot Clock Configuration - This bit
indicates
that the component uses the same physical reference clock that the platform provides on the connector. If the device uses an independent clock irrespective of the presence of a reference clock on the connector, this bit must be clear. For a multi-Function device, each Function must report the same value for this bit.)
Based on my understanding, the BIOS need to read bit "Slot Clock Configurationclear" to see if separate ref clock is used. BIOS then write bit "Common Clock Configuration".
On our board, the bit "Slot Clock Configuration" is always 1, which I
assume
should be 0.
My question is, how the hardware affect the bit "Slot Clock
Configuration"?
How do we need to design our board to make the bit "Slot Clock Configuration" be 0?
Thanks.
Zheng