r796 - coreboot-v3/southbridge/amd/cs5536

Author: hailfinger
Date: 2008-08-22 02:34:28 +0200 (Fri, 22 Aug 2008)
New Revision: 796

Modified:
   coreboot-v3/southbridge/amd/cs5536/cs5536.c
Log:
CS5536 UART: better depbug prints.

This is the part of the acked patch which was to become r649 but missed
in the check in.
I'm reusing the signoff and ack.

Signed-off-by: Carl-Daniel Hailfinger 
Signed-off-by: Ronald G. Minnich 
Acked-by: Stefan Reinauer

Modified: coreboot-v3/southbridge/amd/cs5536/cs5536.c
===================================================================
--- coreboot-v3/southbridge/amd/cs5536/cs5536.c	2008-08-21 19:38:32 UTC (rev 795)
+++ coreboot-v3/southbridge/amd/cs5536/cs5536.c	2008-08-22 00:34:28 UTC (rev 796)
@@ -360,23 +360,26 @@
    	msr = rdmsr(MDD_LEG_IO);
    	msr.lo |= addr << 20;
    	wrmsr(MDD_LEG_IO, msr);
+		printk(BIOS_SPEW, "uarts_init: wrote COM2 address 0x%x\n", sb->com2_address);

/* Set the IRQ. */
    	msr = rdmsr(MDD_IRQM_YHIGH);
    	msr.lo |= sb->com2_irq << 28;
    	wrmsr(MDD_IRQM_YHIGH, msr);
+		printk(BIOS_SPEW, "uarts_init: set COM2 irq\n");

/* GPIO3 - UART2_RX */
    	/* Set: Output Enable (0x4) */
    	outl(GPIOL_3_SET, gpio_addr + GPIOL_OUTPUT_ENABLE);
-
+		printk(BIOS_SPEW, "uarts_init: set output enable\n");
    	/* Set: OUTAUX1 Select (0x10) */
    	outl(GPIOL_3_SET, gpio_addr + GPIOL_OUT_AUX1_SELECT);
+		printk(BIOS_SPEW, "uarts_init: set OUTAUX1\n");

/* GPIO4 - UART2_TX */
    	/* Set: Input Enable (0x20) */
    	outl(GPIOL_4_SET, gpio_addr + GPIOL_INPUT_ENABLE);
-
+		printk(BIOS_SPEW, "uarts_init: set COM2 input enable\n");
    	/* Set: INAUX1 Select (0x34) */
    	/* this totally disables com2 for serial, leave it out until we can
    	 * figure it out
@@ -384,9 +387,10 @@
 //		outl(GPIOL_4_SET, gpio_addr + GPIOL_IN_AUX2_SELECT);
 //		printk(BIOS_SPEW, "uarts_init: set INAUX2 for COM2\n");

-		/* Set: GPIO 3 + 3 Pull Up (0x18) */
+		/* Set: GPIO 3 + 4 Pull Up (0x18) */
    	outl(GPIOL_3_SET | GPIOL_4_SET,
    	     gpio_addr + GPIOL_PULLUP_ENABLE);
+		printk(BIOS_SPEW, "uarts_init: set pullup COM2\n");

/* Enable COM2.
    	 *
@@ -664,6 +668,7 @@
    lpc_init(sb);
    uarts_init(sb, dev);

+	printk(BIOS_SPEW, "cs5536: done uarts_init\n");
    if (sb->enable_gpio_int_route) {
    	printk(BIOS_SPEW, "cs5536: call vr_write\n");
    	vr_write((VRC_MISCELLANEOUS << 8) + PCI_INT_AB,