Hi. I compiled coreboot image for Asus m2n-e (mcp55,ite 8716f). This board turns off after few seconds The log from serial
Welcome to minicom 2.5
OPTIONS:
Compiled on Dec 4 2011, 11:23:38. Port /dev/ttyS0
Press CTRL-A Z for help on special keys
coreboot-4.0-1980-gcc16cca-dirty Sat Jan 28 15:06:08 EST 2012 starting... *sysinfo range: [000cf000,000cf730] bsp_apicid=0x00
Enabling routing table for node 00 done. Enabling UP settings Disabling read/write/fill probes for UP... done. coherent_ht_finalize done core0 started: started ap apicid: SBLink=00 NC node|link=00 entering optimize_link_incoherent_ht sysinfo->link_pair_num=0x1
entering ht_optimize_link pos=0x8a, unfiltered freq_cap=0x8075 pos=0x8a, filtered freq_cap=0x75 pos=0x52, unfiltered freq_cap=0x807f pos=0x52, filtered freq_cap=0x7f freq_cap1=0x75, freq_cap2=0x7f dev1 old_freq=0x0, freq=0x6, needs_reset=0x1 dev2 old_freq=0x0, freq=0x6, needs_reset=0x1 width_cap1=0x11, width_cap2=0x11 dev1 input ln_width1=0x4, ln_width2=0x4 dev1 input width=0x1 dev1 output ln_width1=0x4, ln_width2=0x4 dev1 input|output width=0x11 old dev1 input|output width=0x11 dev2 input|output width=0x11 old dev2 input|output width=0x11 after ht_optimize_link for link pair 0, reset_needed=0x1 after optimize_link_read_pointers_chain, reset_needed=0x1 mcp55_num:01
ht reset -
coreboot-4.0-1980-gcc16cca-dirty Sat Jan 28 15:06:08 EST 2012 starting... *sysinfo range: [000cf000,000cf730] bsp_apicid=0x00
Enabling routing table for node 00 done. Enabling UP settings Disabling read/write/fill probes for UP... done. coherent_ht_finalize
done
core0 started: started ap apicid: SBLink=00
NC node|link=00
entering optimize_link_incoherent_ht sysinfo->link_pair_num=0x1
entering ht_optimize_link pos=0x8a, unfiltered freq_cap=0x8075 pos=0x8a, filtered freq_cap=0x75 pos=0x52, unfiltered freq_cap=0x7f pos=0x52, filtered freq_cap=0x7f freq_cap1=0x75, freq_cap2=0x7f dev1 old_freq=0x6, freq=0x6, needs_reset=0x0 dev2 old_freq=0x6, freq=0x6, needs_reset=0x0 width_cap1=0x11, width_cap2=0x11 dev1 input ln_width1=0x4, ln_width2=0x4 dev1 input width=0x1 dev1 output ln_width1=0x4, ln_width2=0x4 dev1 input|output width=0x11 old dev1 input|output width=0x11 dev2 input|output width=0x11 old dev2 input|output width=0x11 after ht_optimize_link for link pair 0, reset_needed=0x0 after optimize_link_read_pointers_chain, reset_needed=0x0 mcp55_num:01
Ram1.00
setting up CPU 00 northbridge registers done.
Ram2.00
sdram_set_spd_registers: paramx :000cef20 Enable 64MuxMode & BurstLength32 Unbuffered
333MHz
333MHz
set_ecc spd_device: 0x51 Interleaving disabled RAM end at 0x00080000 kB Ram3
ECC enabled Initializing memory: done Setting variable MTRR 2, base: 0MB, range: 512MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=03
done
set DQS timing:DQSPos: 00 TrainDQSRdWrPos: buf_a:000ce9f0 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8d8 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=58
done
Total DQS Training : tsc [00]=0000000012e40bef Total DQS Training : tsc [01]=000000001358f446 Total DQS Training : tsc [02]=0000000018d60c82 Total DQS Training : tsc [03]=0000000019771d46 Ram4
v_esp=000cef68
testx = 5a5a5a5a
INIT detected from --- { APICID = 00 NODEID = 00 COREID = 00} ---
Issuing SOFT_RESET...
coreboot-4.0-1980-gcc16cca-dirty Sat Jan 28 15:06:08 EST 2012 starting... *sysinfo range: [000cf000,000cf730] bsp_apicid=0x00
Enabling routing table for node 00 done. Enabling UP settings Disabling read/write/fill probes for UP... done. coherent_ht_finalize
done
core0 started: started ap apicid: SBLink=00
NC node|link=00
entering optimize_link_incoherent_ht sysinfo->link_pair_num=0x1
entering ht_optimize_link pos=0x8a, unfiltered freq_cap=0x8075 pos=0x8a, filtered freq_cap=0x75 pos=0x52, unfiltered freq_cap=0x7f pos=0x52, filtered freq_cap=0x7f freq_cap1=0x75, freq_cap2=0x7f dev1 old_freq=0x6, freq=0x6, needs_reset=0x0 dev2 old_freq=0x6, freq=0x6, needs_reset=0x0 width_cap1=0x11, width_cap2=0x11 dev1 input ln_width1=0x4, ln_width2=0x4 dev1 input width=0x1 dev1 output ln_width1=0x4, ln_width2=0x4 dev1 input|output width=0x11 old dev1 input|output width=0x11 dev2 input|output width=0x11 old dev2 input|output width=0x11 after ht_optimize_link for link pair 0, reset_needed=0x0 after optimize_link_read_pointers_chain, reset_needed=0x0 mcp55_num:01
Ram1.00
setting up CPU 00 northbridge registers done.
Ram2.00
sdram_set_spd_registers: paramx :000cef20 Enable 64MuxMode & BurstLength32 Unbuffered
333MHz
333MHz
set_ecc spd_device: 0x51 Interleaving disabled RAM end at 0x00080000 kB Ram3
ECC enabled Initializing memory: done Setting variable MTRR 2, base: 0MB, range: 512MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=03
done
set DQS timing:DQSPos: 00 TrainDQSRdWrPos: buf_a:000ce9f0 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8d8 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=58
done
Total DQS Training : tsc [00]=0000000012e3eacf Total DQS Training : tsc [01]=000000001358d326 Total DQS Training : tsc [02]=0000000018d97cfa Total DQS Training : tsc [03]=00000000197a8c56 Ram4
v_esp=000cef68
testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... D
INIT detected from --- { APICID = 00 NODEID = 00 COREID = 00} ---
Issuing SOFT_RESET...
coreboot-4.0-1980-gcc16cca-dirty Sat Jan 28 15:06:08 EST 2012 starting... *sysinfo range: [000cf000,000cf730] bsp_apicid=0x00
Enabling routing table for node 00 done. Enabling UP settings Disabling read/write/fill probes for UP... done. coherent_ht_finalize
done
core0 started: started ap apicid: SBLink=00
NC node|link=00
entering optimize_link_incoherent_ht sysinfo->link_pair_num=0x1
entering ht_optimize_link pos=0x8a, unfiltered freq_cap=0x8075 pos=0x8a, filtered freq_cap=0x75 pos=0x52, unfiltered freq_cap=0x7f pos=0x52, filtered freq_cap=0x7f freq_cap1=0x75, freq_cap2=0x7f dev1 old_freq=0x6, freq=0x6, needs_reset=0x0 dev2 old_freq=0x6, freq=0x6, needs_reset=0x0 width_cap1=0x11, width_cap2=0x11 dev1 input ln_width1=0x4, ln_width2=0x4 dev1 input width=0x1 dev1 output ln_width1=0x4, ln_width2=0x4 dev1 input|output width=0x11 old dev1 input|output width=0x11 dev2 input|output width=0x11 old dev2 input|output width=0x11 after ht_optimize_link for link pair 0, reset_needed=0x0 after optimize_link_read_pointers_chain, reset_needed=0x0 mcp55_num:01
Ram1.00
setting up CPU 00 northbridge registers done.
Ram2.00
sdram_set_spd_registers: paramx :000cef20 Enable 64MuxMode & BurstLength32 Unbuffered
333MHz
333MHz
set_ecc spd_device: 0x51 Interleaving disabled RAM end at 0x00080000 kB Ram3
ECC enabled Initializing memory: done Setting variable MTRR 2, base: 0MB, range: 512MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=03
done
set DQS timing:DQSPos: 00 TrainDQSRdWrPos: buf_a:000ce9f0 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8d8 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=58
done
Total DQS Training : tsc [00]=0000000012e3ed63 Total DQS Training : tsc [01]=000000001358f68a Total DQS Training : tsc [02]=0000000018d73a6a Total DQS Training : tsc [03]=0000000019784e5a Ram4
v_esp=000cef68
testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... m
INIT detected from --- { APICID = 00 NODEID = 00 COREID = 00} ---
Issuing SOFT_RESET...
coreboot-4.0-1980-gcc16cca-dirty Sat Jan 28 15:06:08 EST 2012 starting... *sysinfo range: [000cf000,000cf730] bsp_apicid=0x00
Enabling routing table for node 00 done. Enabling UP settings Disabling read/write/fill probes for UP... done. coherent_ht_finalize
done
core0 started: started ap apicid: SBLink=00
NC node|link=00
entering optimize_link_incoherent_ht sysinfo->link_pair_num=0x1
entering ht_optimize_link pos=0x8a, unfiltered freq_cap=0x8075 pos=0x8a, filtered freq_cap=0x75 pos=0x52, unfiltered freq_cap=0x7f pos=0x52, filtered freq_cap=0x7f freq_cap1=0x75, freq_cap2=0x7f dev1 old_freq=0x6, freq=0x6, needs_reset=0x0 dev2 old_freq=0x6, freq=0x6, needs_reset=0x0 width_cap1=0x11, width_cap2=0x11 dev1 input ln_width1=0x4, ln_width2=0x4 dev1 input width=0x1 dev1 output ln_width1=0x4, ln_width2=0x4 dev1 input|output width=0x11 old dev1 input|output width=0x11 dev2 input|output width=0x11 old dev2 input|output width=0x11 after ht_optimize_link for link pair 0, reset_needed=0x0 after optimize_link_read_pointers_chain, reset_needed=0x0 mcp55_num:01
Ram1.00
setting up CPU 00 northbridge registers done.
Ram2.00
sdram_set_spd_registers: paramx :000cef20 Enable 64MuxMode & BurstLength32 Unbuffered
333MHz
333MHz
set_ecc spd_device: 0x51 Interleaving disabled RAM end at 0x00080000 kB Ram3
ECC enabled Initializing memory: done Setting variable MTRR 2, base: 0MB, range: 512MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=03
done
set DQS timing:DQSPos: 00 TrainDQSRdWrPos: buf_a:000ce9f0 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8c8 TrainDQSPos: MutualCSPassW[48] :000ce8d8 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=58
done
Total DQS Training : tsc [00]=0000000012e4504b Total DQS Training : tsc [01]=0000000013593c4a Total DQS Training : tsc [02]=0000000018d6d4b2 Total DQS Training : tsc [03]=000000001977e9ce Ram4
v_esp=000cef68
testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack...
-
Julian Shulika