How I can start a cluster with M825G VIA KM266-8235,

[Edmanuel Torres]

I want to build a cluster based in the M825G with chipset VIA KM266-8235
mainboard from PCCHIPS, but I have found that this is not supported by the
available configuration files in the mainboards folder. I wonder is
somebody can help me in to find the way to make this board work with
LinuxBios?. below is the output of the -lspci -vvv command. Thanks in
advance, Edmanuel

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8375 [KM266/KL266] Host
Bridge
    Subsystem: VIA Technologies, Inc. VT8375 [KM266/KL266] Host Bridge
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
    Latency: 8
    Region 0: Memory at ea000000 (32-bit, prefetchable) [size=4M]
    Capabilities: [a0] AGP version 2.0
    	Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW-
AGP3- Rate=x1,x2,x4
    	Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x2,x4
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
(prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: e8000000-e9ffffff
    Prefetchable memory behind bridge: e0000000-e7ffffff
    BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
    Capabilities: [80] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
    Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
    Latency: 0
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if
8a [Master SecP PriP])
    Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
    Latency: 32
    Interrupt: pin A routed to IRQ 20
    Region 4: I/O ports at dc00 [size=16]
    Capabilities: [c0] Power Management version 2
    	Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II]
(rev 74)
    Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet
Controller on VT8235
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
    Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 23
    Region 0: I/O ports at e000 [size=256]
    Region 1: Memory at ea401000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [40] Power Management version 2
    	Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.0 VGA compatible controller: S3 Inc. VT8375 [ProSavage8
KM266/KL266] (prog-if 00 [VGA])
    Subsystem: S3 Inc. VT8375 [ProSavage8 KM266/KL266]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
    Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at e9000000 (32-bit, non-prefetchable) [size=512K]
    Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
    Expansion ROM at <unassigned> [disabled] [size=64K]
    Capabilities: [dc] Power Management version 2
    	Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    	Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] AGP version 2.0
    	Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bi

=================================================
Edmanuel Torres
MSc. in Physics (Student)
Mobile: [phone]
Phone: [phone] Ext 2402
Fax:   [phone]
Physics and Technology Plasma Group
Physics School,
Universidad Industrial de Santander,
Bucaramanga, Colombia
AA 678