Finally!! :-)
Kindly 'svn copy' src/mainboard/lippert/spacerunner-lx to src/mainboard/lippert/hurricane-lx before applying.
Cheers, Jens
Add support for LiPPERT Hurricane-LX (EPIC board with AMD Geode-LX, CS5536, ITE IT8712F). Board support is based on the SpaceRunner-LX (with tiny bits from the RoadRunner-LX) even though the hardware really was the ancestor of our three other -LX boards and in fact among the earliest Geode-LX boards on the market. (Might even have been the first Geode-LX EPIC?)
Signed-off-by: Jens Rottmann JRottmann@LiPPERTEmbedded.de ---
--- src/mainboard/lippert/Kconfig (rev 5796) +++ src/mainboard/lippert/Kconfig (working copy) @@ -5,6 +5,8 @@
config BOARD_LIPPERT_FRONTRUNNER bool "Cool Frontrunner" +config BOARD_LIPPERT_HURRICANE_LX + bool "Hurricane-LX" config BOARD_LIPPERT_LITERUNNER_LX bool "Cool LiteRunner-LX" config BOARD_LIPPERT_ROADRUNNER_LX @@ -15,6 +17,7 @@ endchoice
source "src/mainboard/lippert/frontrunner/Kconfig" +source "src/mainboard/lippert/hurricane-lx/Kconfig" source "src/mainboard/lippert/literunner-lx/Kconfig" source "src/mainboard/lippert/roadrunner-lx/Kconfig" source "src/mainboard/lippert/spacerunner-lx/Kconfig" --- src/mainboard/lippert/hurricane-lx/Kconfig (rev 5796) +++ src/mainboard/lippert/hurricane-lx/Kconfig (working copy) @@ -1,4 +1,4 @@ -if BOARD_LIPPERT_SPACERUNNER_LX +if BOARD_LIPPERT_HURRICANE_LX
config BOARD_SPECIFIC_OPTIONS # dummy def_bool y @@ -7,7 +7,6 @@ select NORTHBRIDGE_AMD_LX select SOUTHBRIDGE_AMD_CS5536 select SUPERIO_ITE_IT8712F - select HAVE_DEBUG_SMBUS select HAVE_PIRQ_TABLE select PIRQ_ROUTE select UDELAY_TSC @@ -18,15 +17,23 @@
config MAINBOARD_DIR string - default lippert/spacerunner-lx + default lippert/hurricane-lx
config MAINBOARD_PART_NUMBER string - default "Cool SpaceRunner-LX" + default "Hurricane-LX"
config IRQ_SLOT_COUNT int - default 7 + default 8 + +config BOARD_OLD_REVISION + bool "Board is old pre-3.0 revision" + default n + help + Look on the bottom side for a number like 406-0001-30. The last 2 + digits state the PCB revision (3.0 in this example). For 2.0 or older + boards choose Y, for 3.0 and newer say N.
config ONBOARD_UARTS_RS485 bool "Switch on-board serial ports to RS485" @@ -35,10 +42,4 @@ If selected, both on-board serial ports will operate in RS485 mode instead of RS232.
-config ONBOARD_IDE_SLAVE - bool "Make on-board SSD act as Slave" - default n - help - If selected, the on-board SSD will act as IDE Slave instead of Master. - -endif # BOARD_LIPPERT_SPACERUNNER_LX +endif # BOARD_LIPPERT_HURRICANE_LX --- src/mainboard/lippert/hurricane-lx/chip.h (rev 5796) +++ src/mainboard/lippert/hurricane-lx/chip.h (working copy) @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * Copyright (C) 2010 LiPPERT Embedded Computers GmbH * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by --- src/mainboard/lippert/hurricane-lx/devicetree.cb (rev 5796) +++ src/mainboard/lippert/hurricane-lx/devicetree.cb (working copy) @@ -21,17 +21,17 @@ register "com2_enable" = "0" register "com2_address" = "0x2E8" register "com2_irq" = "6" - register "unwanted_vpci[0]" = "0x80007B00" # Audio: 1<<31 + Device 0x0F<<11 + Function 3<<8 - register "unwanted_vpci[1]" = "0" # End of list has a zero + register "unwanted_vpci[0]" = "0" # End of list has a zero device pci 8.0 on end # Slot4 device pci 9.0 on end # Slot3 device pci a.0 on end # Slot2 device pci b.0 on end # Slot1 device pci c.0 on end # IT8888 + device pci d.0 on end # Mini-PCI device pci e.0 on end # Ethernet device pci f.0 on # ISA Bridge chip superio/ite/it8712f - device pnp 2e.0 off # Floppy + device pnp 2e.0 on # Floppy io 0x60 = 0x3f0 irq 0x70 = 6 drq 0x74 = 2 @@ -76,7 +76,7 @@ end end device pci f.2 on end # IDE - device pci f.3 off end # Audio + device pci f.3 on end # Audio device pci f.4 on end # OHCI device pci f.5 on end # EHCI end --- src/mainboard/lippert/hurricane-lx/irq_tables.c (rev 5796) +++ src/mainboard/lippert/hurricane-lx/irq_tables.c (working copy) @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * Copyright (C) 2010 LiPPERT Embedded Computers GmbH * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,7 +18,7 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */
-/* Based on irq_tables.c from AMD's DB800 mainboard. */ +/* Based on irq_tables.c from the SpaceRunner-LX mainboard. */
#include <arch/pirq_routing.h> #include <console/console.h> @@ -55,17 +55,18 @@ 0x002B, /* Device */ 0, /* Crap (miniport) */ {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */ - 0xE0, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ + 0x36, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ { /* If you change the number of entries, change the CONFIG_IRQ_SLOT_COUNT above! */ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* CPU */ {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */ - {0x00, (0x0E << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */ + {0x00, (0x0E << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */ {0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0}, /* slot1 */ {0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0}, /* slot2 */ {0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0}, /* slot3 */ {0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0}, /* slot4 */ + {0x00, (0x0D << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}}, 0x5, 0x0}, /* Mini-PCI */ } };
--- src/mainboard/lippert/hurricane-lx/mainboard.c (rev 5796) +++ src/mainboard/lippert/hurricane-lx/mainboard.c (working copy) @@ -1,7 +1,7 @@ /* * This file is part of the coreboot project. * - * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * Copyright (C) 2010 LiPPERT Embedded Computers GmbH * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,7 +18,7 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */
-/* Based on mainboard.c from AMD's DB800 mainboard. */ +/* Based on mainboard.c from the SpaceRunner-LX mainboard. */
#include <stdlib.h> #include <stdint.h> @@ -29,16 +29,15 @@ #include <device/pci_ids.h> #include "chip.h"
-/* Bit0 turns off the Live LED, bit1 switches Com1 to RS485, bit2 same for Com2. */ +/* Bit1 switches Com1 to RS485, bit2 same for Com2. */ #if CONFIG_ONBOARD_UARTS_RS485 - #define SIO_GP1X_CONFIG 0x07 + #define SIO_GP1X_CONFIG 0x06 #else - #define SIO_GP1X_CONFIG 0x01 + #define SIO_GP1X_CONFIG 0x00 #endif
static const u16 ec_init_table[] = { /* hi=data, lo=index */ 0x1900, /* Enable monitoring */ - 0x3050, /* VIN4,5 enabled */ 0x0351, /* TMPIN1,2 diode mode, TMPIN3 off */ 0x805C, /* Unlock zero adjust */ 0x7056, 0x3C57, /* Zero adjust TMPIN1,2 */ @@ -49,20 +48,22 @@ static void init(struct device *dev) { unsigned int gpio_base, i; - printk(BIOS_DEBUG, "LiPPERT SpaceRunner-LX ENTER %s\n", __func__); + printk(BIOS_DEBUG, "LiPPERT Hurricane-LX ENTER %s\n", __func__);
/* Init CS5536 GPIOs */ gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1;
outl(0x00000040, gpio_base + 0x00); // GPIO6 value 1 - LAN_PD# + outl(0x00000040, gpio_base + 0x08); // GPIO6 open drain 1 - LAN_PD# (jumpered GPIO per default) outl(0x00000040, gpio_base + 0x04); // GPIO6 output 1 - LAN_PD# - outl(0x04000000, gpio_base + 0x18); // GPIO10 pull up 0 - THRM_ALRM# outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1 1 - THRM_ALRM# outl(0x00000400, gpio_base + 0x20); // GPIO10 input 1 - THRM_ALRM# +#if !CONFIG_BOARD_OLD_REVISION outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2 1 - 32kHz outl(0x00000800, gpio_base + 0x84); // GPIO27 output 1 - 32kHz - outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz +#endif + outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz (new) / PM-LED (old)
/* Init Environment Controller. */ for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) { @@ -71,10 +72,10 @@ outb(val >> 8, 0x0296); }
- /* bit2 = RS485_EN2, bit1 = RS485_EN1, bit0 = Live LED */ + /* bit2 = RS485_EN2, bit1 = RS485_EN1 */ outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */
- printk(BIOS_DEBUG, "LiPPERT SpaceRunner-LX EXIT %s\n", __func__); + printk(BIOS_DEBUG, "LiPPERT Hurricane-LX EXIT %s\n", __func__); }
static void enable_dev(struct device *dev) @@ -83,6 +84,6 @@ }
struct chip_operations mainboard_ops = { - CHIP_NAME("LiPPERT SpaceRunner-LX Mainboard") + CHIP_NAME("LiPPERT Hurricane-LX Mainboard") .enable_dev = enable_dev, }; --- src/mainboard/lippert/hurricane-lx/romstage.c (rev 5796) +++ src/mainboard/lippert/hurricane-lx/romstage.c (working copy) @@ -2,7 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2007 Advanced Micro Devices, Inc. - * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * Copyright (C) 2010 LiPPERT Embedded Computers GmbH * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -19,11 +19,10 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */
-/* Based on romstage.c from AMD's DB800 and DBM690T mainboards. */ +/* Based on romstage.c from the SpaceRunner-LX mainboard. */
#include <stdlib.h> #include <stdint.h> -#include <spd.h> #include <device/pci_def.h> #include <arch/io.h> #include <device/pnp_def.h> @@ -40,66 +39,24 @@ #include "southbridge/amd/cs5536/cs5536_early_setup.c" #include "superio/ite/it8712f/it8712f_early_serial.c"
-/* Bit0 enables Spread Spectrum, bit1 makes on-board SSD act as IDE slave. */ -#if CONFIG_ONBOARD_IDE_SLAVE - #define SMC_CONFIG 0x03 -#else - #define SMC_CONFIG 0x01 -#endif +/* Bit0 enables Spread Spectrum. */ +#define SMC_CONFIG 0x01
#define ManualConf 1 /* No automatic strapped PLL config */ -#define PLLMSRhi 0x0000059C /* Manual settings for the PLL */ +#define PLLMSRhi 0x0000049C /* Manual settings for the PLL */ #define PLLMSRlo 0x00DE6001 #define DIMM0 0xA0 #define DIMM1 0xA2
-static const unsigned char spdbytes[] = { // 4x Promos V58C2512164SA-J5I - 0xFF, 0xFF, // only values used by Geode-LX raminit.c are set - [SPD_MEMORY_TYPE] = SPD_MEMORY_TYPE_SDRAM_DDR, // (Fundamental) memory type - [SPD_NUM_ROWS] = 0x0D, // Number of row address bits [13] - [SPD_NUM_COLUMNS] = 0x0A, // Number of column address bits [10] - [SPD_NUM_DIMM_BANKS] = 1, // Number of module rows (banks) - 0xFF, 0xFF, 0xFF, - [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 0x50, // SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD] - 0xFF, 0xFF, - [SPD_REFRESH] = 0x82, // Refresh rate/type [Self Refresh, 7.8 us] - [SPD_PRIMARY_SDRAM_WIDTH] = 64, // SDRAM width (primary SDRAM) [64 bits] - 0xFF, 0xFF, 0xFF, - [SPD_NUM_BANKS_PER_SDRAM] = 4, // SDRAM device attributes, number of banks on SDRAM device - [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x1C, // SDRAM device attributes, CAS latency [3, 2.5, 2] - 0xFF, 0xFF, - [SPD_MODULE_ATTRIBUTES] = 0x20, // SDRAM module attributes [differential clk] - [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0x40, // SDRAM device attributes, general [Concurrent AP] - [SPD_SDRAM_CYCLE_TIME_2ND] = 0x60, // SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD] - 0xFF, - [SPD_SDRAM_CYCLE_TIME_3RD] = 0x75, // SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD] - 0xFF, - [SPD_tRP] = 60, // Min. row precharge time [15 ns in units of 0.25 ns] - [SPD_tRRD] = 40, // Min. row active to row active [10 ns in units of 0.25 ns] - [SPD_tRCD] = 60, // Min. RAS to CAS delay [15 ns in units of 0.25 ns] - [SPD_tRAS] = 40, // Min. RAS pulse width = active to precharge delay [40 ns] - [SPD_BANK_DENSITY] = 0x40, // Density of each row on module [256 MB] - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - [SPD_tRFC] = 70 // SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns] -}; - static inline int spd_read_byte(unsigned int device, unsigned int address) { if (device != DIMM0) return 0xFF; /* No DIMM1, don't even try. */
-#if CONFIG_DEBUG_SMBUS - if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) { - print_err("ERROR: spd_read_byte(DIMM0, 0x"); - print_err_hex8(address); - print_err(") returns 0xff\n"); - } -#endif - - /* Fake SPD ROM value */ - return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF; + return smbus_read_byte(device, address); }
+#if !CONFIG_BOARD_OLD_REVISION /* Send config data to System Management Controller via SMB. */ static int smc_send_config(unsigned char config_data) { @@ -118,6 +75,7 @@ smbus_stop_condition(SMBUS_IO_BASE); return 0; } +#endif
#include "northbridge/amd/lx/raminit.h" #include "northbridge/amd/lx/pll_reset.c" @@ -129,19 +87,21 @@
static const u16 sio_init_table[] = { // hi=data, lo=index 0x0707, // select LDN 7 (GPIO, SPI, watchdog, ...) - 0x072C, // VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal + 0x042C, // disable ATXPG; VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 enabled 0x1423, // don't delay PoWeROK1/2 0x9072, // watchdog triggers PWROK, counts seconds #if !CONFIG_USE_WATCHDOG_ON_BOOT 0x0073, 0x0074, // disarm watchdog by changing 56 s timeout to 0 #endif 0xBF25, 0x172A, 0xF326, // select GPIO function for most pins - 0xFF27, 0xDF28, 0x2729, // (GP45=SUSB, GP23,22,16,15=SPI, GP13=PWROK1) + 0xBF27, 0xFF28, 0x2D29, // (GP36=FAN_CTL3 (PWM), GP23,22,16,15=SPI, GP13=PWROK1) 0x66B8, 0x0CB9, // enable pullups on SPI, RS485_EN - 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED - 0x07C8, // config GP12-10 as output + 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, WD_ACTIVE + 0x06C8, // config GP12,11 as output, GP10 as input 0x2DF5, // map Hw Monitor Thermal Output to GP55 - 0x08F8, // map GP LED Blinking 1 to GP10=LIVE_LED (deactivate Simple I/O to use) +#if CONFIG_BOARD_OLD_REVISION + 0x1F2A, 0xC072, // switch GP13 to GPIO, WDT output from PWROK to KRST +#endif };
/* Early mainboard specific GPIO setup. */ @@ -161,7 +121,6 @@
void main(unsigned long bist) { - int err; post_code(0x01);
static const struct mem_controller memctrl[] = { @@ -189,12 +148,22 @@
cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED);
- /* bit1 = on-board IDE is slave, bit0 = Spread Spectrum */ +#if CONFIG_BOARD_OLD_REVISION + /* + * Old revision boards need a jumper shorting the power button to power + * on automatically. So we must disable the button's fail-safe function, + * or the board will shut down after 4 s. + */ + outl(0, PMS_IO_BASE + PM_FSD); // Fail-Save Delay register +#else + int err; + /* bit0 = Spread Spectrum */ if ((err = smc_send_config(SMC_CONFIG))) { print_err("ERROR "); print_err_char('0'+err); print_err(" sending config data to SMC\n"); } +#endif
sdram_initialize(1, memctrl);
_
I'm remembering why I like you lippert guys so much :-)
ron
Jens Rottmann wrote:
Kindly 'svn copy' src/mainboard/lippert/spacerunner-lx to src/mainboard/lippert/hurricane-lx before applying.
Cheers, Jens
Add support for LiPPERT Hurricane-LX (EPIC board with AMD Geode-LX, CS5536, ITE IT8712F). Board support is based on the SpaceRunner-LX (with tiny bits from the RoadRunner-LX) even though the hardware really was the ancestor of our three other -LX boards and in fact among the earliest Geode-LX boards on the market. (Might even have been the first Geode-LX EPIC?)
Signed-off-by: Jens Rottmann JRottmann@LiPPERTEmbedded.de
Acked-by: Peter Stuge peter@stuge.se
(Someone please commit, I'm away from a working tree atm.)
//Peter
On Fri, Sep 10, 2010 at 3:37 PM, Peter Stuge peter@stuge.se wrote:
Jens Rottmann wrote:
Kindly 'svn copy' src/mainboard/lippert/spacerunner-lx to src/mainboard/lippert/hurricane-lx before applying.
Cheers, Jens
Add support for LiPPERT Hurricane-LX (EPIC board with AMD Geode-LX, CS5536, ITE IT8712F). Board support is based on the SpaceRunner-LX (with tiny bits from the RoadRunner-LX) even though the hardware really was the ancestor of our three other -LX boards and in fact among the earliest Geode-LX boards on the market. (Might even have been the first Geode-LX EPIC?)
Signed-off-by: Jens Rottmann JRottmann@LiPPERTEmbedded.de
Acked-by: Peter Stuge peter@stuge.se
Rev 5801.
Thanks, Myles
-
Jens Rottmann -
Myles Watson -
Peter Stuge -
ron minnich