coreboot

coreboot@coreboot.org

3 participants
39562 discussions

Re: K8 + 2.4.21 + SuSE 64-bit mode + Arima HDAMA + 49LF040 + MTD
by YhLu 14 Jul '03

14 Jul '03

Eric, I have tried to build the tg3--ide_disk.zelf and use it in fallback and normal but all failed. In fallback track: It said: Searching for image...................................<abort> In Normal track: It said: Wrong index I have use to cmos_util to change boot track and BOOT_FIRST=HDD and BOOT_SECOND=Network. When building tg3--ide_disk.zelf, I used BOOT_FIRST=IDE and BOOT_SECOND=NIC. What kind of image in HDD that eltherboot wound want? Regards Yinghai Lu Fallback: Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 Found ELF candiate at offset 0 Loading Etherboot version: 5.1.8 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x3586f offset 0xb0 filesize 0x5d65 (cleaned up) New segment addr 0x20000 size 0x3586f offset 0xb0 filesize 0x5d65 Loading Segment: addr: 0x0000000000020000 memsz: 0x000000000003586f filesz: 0x00 00000000005d65 Clearing Segment: addr: 0x0000000000025d65 memsz: 0x000000000002fb0a Jumping to boot code at 0x20000 ROM segment 0x33cc length 0x9842 reloc 0x00020000 CPU 1859 Mhz Etherboot 5.1.8 (GPL) Tagged ELF (Multiboot) for [TG3][IDE] Relocating _text from: [00025d70,00056480) to [5ffcf8f0,60000000) Probing pci disk... [IDE]disk-1 80043264k cap: 2f00 Searching for image... ................................<abort> Probing pci disk... [IDE]Probing isa disk... Probing pci nic... [TG3]Cannot find PowerManagement capability, aborting. [TG3]Ethernet addr: 00:E0:81:52:6C:56 Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) Link is up at 100 Mbps, half duplex. Searching for server (DHCP)... ..Me: 192.168.1.200, Server: 192.168.1.1, Gateway 192.168.1.1 Loading 192.168.1.1:ram0_2.5_2.4.21_k8_lsi_mydisk4.elf ...(ELF).. Normal: Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 Found ELF candiate at offset 0 Loading Etherboot version: 5.1.8 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x3586f offset 0xb0 filesize 0x5d65 (cleaned up) New segment addr 0x20000 size 0x3586f offset 0xb0 filesize 0x5d65 Loading Segment: addr: 0x0000000000020000 memsz: 0x000000000003586f filesz: 0x00 00000000005d65 Clearing Segment: addr: 0x0000000000025d65 memsz: 0x000000000002fb0a Jumping to boot code at 0x20000 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 1870 Mhz Etherboot 5.1.8 (GPL) Tagged ELF (Multiboot) for [TG3][IDE] Relocating _text from: [00025d70,00056480) to [5ffcf8f0,60000000) Probing pci disk... [IDE]disk-1 80043264k cap: 2f00 Wrong index Probing pci disk... [IDE]Probing isa disk... Probing pci nic... [TG3]Cannot find PowerManagement capability, aborting. [TG3]Ethernet addr: 00:E0:81:52:6C:56 Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) Link is up at 100 Mbps, half duplex. Searching for server (DHCP)... ..Me: 192.168.1.200, Server: 192.168.1.1, Gateway 192.168.1.1 Loading 192.168.1.1:ram0_2.5_2.4.21_k8_lsi_mydisk4.elf ...(ELF)... ............. ...........................................................................

2 1

Re: ppc linuxbios support
by Greg Watson 13 Jul '03

13 Jul '03

Hi Ramkumar, Ports to new boards, or suggestions on how to make the PPC code more modular and robust are always appreciated. You might want to start by getting linuxbios booting a linux kernel on the 755. This shouldn't be too difficult, as the 755 appears to use the same northbridge as the 7410. I used the MontiVista linux as it was already ported to the Sandpoint, though I had to make a few patches to get it to boot with linuxbios. Let me know when you get to this point and I can send you the patches. I've just ordered an EP405PC from EmbeddedPlanet which will be my next port. It uses the IBM PPC 405Gpr chip which is sufficiently different to the 7410 to be challenging. Hopefully this week I'll have the PPC version working under the new configuration system (check out freebios2 instead of freebios). This is going to allow us to build a static device tree which can be passed to linux. Heiko Schick and I have been discussing the possibility of mapping this device tree to an Open Firmware device tree that can then be used to boot linux on an OF system (such as Power Mac's). Stefan Reinauer has reminded me that we should work with the openbios community on this, though looking at the IEEE 1275 spec (all 250+ pages) I think they've got a big job ahead. :-) Cheers, Greg >I would be interested in helping out in the testing/development of >the PPC BIOS. Also, have access to sandpoint 755. Let me know if I >can help. > >Thanks > >Ramkumar

1 0

audio support?
by Devi Priya 12 Jul '03

12 Jul '03

Hello, It is said that audio support is not good in geode sc1200 using linuxbios. Then to get audio support what actions to be done? Thanks in advance for any help! _________________________________________________________________ Are you a geek? Do gizmos make you grin? http://www.msn.co.in/Computing/Gizmos/ Click here!

2 1

Linuxbios, bugfix in sis flash_rom
by Felix Kloeckner 12 Jul '03

12 Jul '03

Hello, after wondering why flash_rom wasn't working, i found that the compiler did some optimization on the reading/writing from/to the flash. So i made the variables for accessing the flash 'volatile', now it works! could you apply the patch to the linuxbios cvs? thanks Felix Kloeckner ps this patch is for jedec flash only, other parts probably have the same problem

2 3

files to be placed in target.
by Devi Priya 12 Jul '03

12 Jul '03

Hello, These are the files in my build directory when I built my linuxbios for geode sc1200. I don't use DOC. boot.o isa-dma.o linuxbios_payload.nrv2b nrv2b clog2.o keyboard.o linuxbios.rom nsuperio.c compute_ip_checksum.o ldoptions linuxbios.strip params.o cpuid.o ldscript.ld linuxbios_table.o payload.block crt0_includes.h linux.bin.gz linuxpci.o printk.o crt0.o linuxbios mainboard.o rom_fill_inbuf.o crt0.s linuxbios.a Makefile romimage crt0.S linuxbios_c Makefile.settings serial_subr.o c_start.o linuxbios_c.map malloc.o southbridge.o c_start.s linuxbios_c.o mc146818rtc.o subr.o delay.o LinuxBIOSDoc.config memcmp.o version.o do_inflate.o linuxbiosmain.o memcpy.o vsprintf.o hardwaremain.o linuxbios.map memset.o i386_subr.o linuxbios_payload newpci.o ide.o linuxbios_payload.bin northbridge.o Out of these files, plz tell what for each of the following files stands for: linux.bin.gz linuxbios (executable file) linuxbios.a (contains many .o files) linuxbios_c (executable file) linuxbios_payload (unknown type) linuxbios_payload.bin linuxbios.nrv2b linuxbios.rom linuxbios.strip nrv2b(executable) payload.block(Gzip file) romimage (Gzip file) Out of these files which files are to be placed in the target? Thanks in advance for any help in advance. _________________________________________________________________ Polyphonic ringtones. Latest movie trailors. http://server1.msn.co.in/sp03/gprs/index.asp On your mobile!

1 0

how to set 100 FSB for sis630
by tu guangxiu 12 Jul '03

12 Jul '03

I need my winfast6300( using sis630 )to support 100M FSB. I know that there is sis630.reg, who has some glues to set FSB from 66 to 100 in sis630.reg or other file? thanks __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com

1 0

Re: K8 + 2.4.21 + SuSE 64-bit mode + Arima HDAMA + 49LF040 + MTD
by YhLu 12 Jul '03

12 Jul '03

Eric, I switch to RH preview AMD 64 to build the kernel now the MB can finish the booting. I also try to boot local HD in normal boot. I use hda1 to store elf ( Kernel+RAM disk). But LinuxBIOS seems don't recogonize the elf format. And failed. I have use tg3.zelf to substitute the elf in the HD. LinuxBIOS can load it from HD and execute it. Any idea to produce ELF for HD booting. Or LinuxBIOS now only support 23bit elf? Regards Yinghai Lu

2 1

ANN: arima hdama boots...
by ebiederman＠lnxi.com 12 Jul '03

12 Jul '03

I have finally gotten all of the hard codes out of the memory initialization code and I can get the Arima HDAMA dual Opteron motherboard booting. And I have checked in the code. There is a lot more to do including cleanup of the code that works but one major piece is done. Eric

1 0

freebios2 and $Id:
by ebiederman＠lnxi.com 12 Jul '03

12 Jul '03

Unless someone has something to say in defense of the $Id: construct I am hereby banning it from the freebios2 tree. It makes it a pain to maintain a secondary CVS tree in sync as there are multiple unnecessary hits. Didn't we already ban $Id: ? in freebios2. In any case a huge lot of them had slipped in and I have removed all of them from the tree. And I intend to keep doing that when ever I find more of them. Eric

1 0

Any EPIA etherboot success stories?
by David Hendricks 11 Jul '03

11 Jul '03

I see a lot of people here have gotten LinuxBIOS working with the Via EPIA using an IDE device, but has anyone managed to get it working using etherboot to boot a kernel over a network? I'm a hopeless newbie and have been struggling with this for some time. I have links to logs, my payload, and my config below (Trying to keep the list archives tidy). I had gotten etherboot working with the PCM-5823s earlier and compared the minicom log with that of my Epia. The only real obvious discrepency I see is the entry point. The Geode entered at 0x00094000 (606,208), while the Epia is trying to enter at 0x00020000 (131,072). I'm using CVS versions of Etherboot and LinuxBios. However, I haven't been able to update in the past one or two weeks due to Sourceforge's problems so I might have missed an important patch. Links EPIA minicom log (High verbosity): http://www.flagen.com/~sc/linux/funstuff/epia-dave My Rhine payload: http://www.flagen.com/~sc/linux/funstuff/via-rhine-ebcvs.elf My config file: http://www.flagen.com/~sc/linux/funstuff/epia.config Geode (Elfboot part only): http://www.flagen.com/~sc/linux/funstuff/geode-elfboot-dave TIA --David

4 6

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot