coreboot November 2011

coreboot@coreboot.org

39 participants
432 discussions

Re: [coreboot] How to change clockchip frequency?
by Oskar Enoksson 02 Nov '11

02 Nov '11

On 11/02/2011 04:31 PM, Marc Jones wrote: > On Wed, Nov 2, 2011 at 6:37 AM, Oskar Enoksson<enok(a)lysator.liu.se> wrote: >> I have a chip called CDC960 on my motherboard. It is responsible for >> generating the bus frequency for the cpu, the pci bus etc. I downloaded the >> datasheet and noticed that I can change the base frequency by +/-10% by >> sending an smbus command to the cdc960. >> >> When I sent the smbus commands from a running linux the system froze for a >> few seconds and then rebooted. But after reboot the frequency was indeed >> changed (overclocked) and everything worked just fine. >> >> I tried to add the smbus command to romstage.c in my coreboot, but that >> didn't work. The boot process just hanged immediately after the smbus >> command had been sent. >> >> I guess the running CPU (or something else in the system) cannot handle the >> frequency change and needs to be reset immediately after the command is >> sent. Perhaps some watchdog under Linux resets the system after a few >> seconds of irresponsiveness. But what is the recommended way in coreboot? > It would be hard to tell why Linux resets, but you can look in the > southbridge for a watchdog. You should also read the CPU spec about > changing clock speed etc. Thanks. There is a watchdog in the southbridge (amd 8111) and it could be set up to reset the system after a specified number of seconds, but it requires memory mapped I/O to work and I'm not sure how to do that in coreboot. Do you (or someone else) think it's a doable way? If so I'll give it a try ...

2 1

Patch set updated for coreboot: b838977 some black magic for initializing the old version of the k8t800
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/388 -gerrit commit b838977c3554e0775a0fea4ad6c09a9132db2ce7 Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:38 2011 +0100 some black magic for initializing the old version of the k8t800 Change-Id: I1b5d23cee9f933aa090c9bd09890c7b335567e17 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/southbridge/via/k8t890/bridge.c | 9 +++++++++ src/southbridge/via/k8t890/ctrl.c | 11 +++++++++++ 2 files changed, 20 insertions(+), 0 deletions(-) diff --git a/src/southbridge/via/k8t890/bridge.c b/src/southbridge/via/k8t890/bridge.c index 1b21b32..ecfdc35 100644 --- a/src/southbridge/via/k8t890/bridge.c +++ b/src/southbridge/via/k8t890/bridge.c @@ -33,9 +33,14 @@ static void bridge_enable(struct device *dev) writeback(dev, 0x40, 0x91); writeback(dev, 0x41, 0x40); writeback(dev, 0x43, 0x44); +#if CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD + writeback(dev, 0x42, 0x80); + writeback(dev, 0x44, 0x35); +#else writeback(dev, 0x44, 0x31); /* K8M890 should have 0x35 datasheet * says it is reserved */ +#endif writeback(dev, 0x45, 0x3a); writeback(dev, 0x46, 0x88); /* PCI ID lo */ writeback(dev, 0x47, 0xb1); /* PCI ID hi */ @@ -44,7 +49,11 @@ static void bridge_enable(struct device *dev) * (Forward VGA compatible memory and I/O cycles ) */ +#if CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD + writeback(dev, 0x3e, 0x0a); +#else writeback(dev, 0x3e, 0x16); +#endif dump_south(dev); /* disable I/O and memory decode, or it freezes PCI bus during BAR sizing */ diff --git a/src/southbridge/via/k8t890/ctrl.c b/src/southbridge/via/k8t890/ctrl.c index d68e03e..4a6428d 100644 --- a/src/southbridge/via/k8t890/ctrl.c +++ b/src/southbridge/via/k8t890/ctrl.c @@ -37,12 +37,21 @@ void k8x8xx_vt8237r_cfg(struct device *dev, struct device *devsb) pci_write_config8(dev, 0x70, 0xc2); /* PCI Control */ +#if !CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD pci_write_config8(dev, 0x72, 0xee); +#endif pci_write_config8(dev, 0x73, 0x01); +#if CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD + pci_write_config8(dev, 0x74, 0x64); + pci_write_config8(dev, 0x75, 0x3f); +#else pci_write_config8(dev, 0x74, 0x24); pci_write_config8(dev, 0x75, 0x0f); +#endif pci_write_config8(dev, 0x76, 0x50); +#if !CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD pci_write_config8(dev, 0x77, 0x08); +#endif pci_write_config8(dev, 0x78, 0x01); /* APIC on HT */ pci_write_config8(dev, 0x7c, 0x7f); @@ -137,7 +146,9 @@ static void ctrl_init(struct device *dev) /* PCI CFG Address bits[27:24] are used as extended register address bit[11:8] */ +#if !CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD pci_write_config8(dev, 0x47, 0x30); +#endif /* VT8237R specific configuration other SB are done in their own directories */

1 0

Patch set updated for coreboot: e85069f copied asus a8v-e_se to k8v-x
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/389 -gerrit commit e85069ffb48e9be2bc2469e34167fa86e043ee3d Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:40 2011 +0100 copied asus a8v-e_se to k8v-x Change-Id: Ib66e8c5102ad45e73977a06aea109ed9544f4d08 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/mainboard/asus/k8v-x/Kconfig | 73 ++++++++++ src/mainboard/asus/k8v-x/acpi_tables.c | 175 ++++++++++++++++++++++ src/mainboard/asus/k8v-x/chip.h | 22 +++ src/mainboard/asus/k8v-x/cmos.layout | 98 +++++++++++++ src/mainboard/asus/k8v-x/devicetree.cb | 97 +++++++++++++ src/mainboard/asus/k8v-x/dsdt.asl | 249 ++++++++++++++++++++++++++++++++ src/mainboard/asus/k8v-x/mainboard.c | 28 ++++ src/mainboard/asus/k8v-x/mptable.c | 116 +++++++++++++++ src/mainboard/asus/k8v-x/romstage.c | 225 +++++++++++++++++++++++++++++ 9 files changed, 1083 insertions(+), 0 deletions(-) diff --git a/src/mainboard/asus/k8v-x/Kconfig b/src/mainboard/asus/k8v-x/Kconfig new file mode 100644 index 0000000..4975cfa --- /dev/null +++ b/src/mainboard/asus/k8v-x/Kconfig @@ -0,0 +1,73 @@ +if BOARD_ASUS_A8V_E_SE + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + select ARCH_X86 + select CPU_AMD_SOCKET_939 + select K8_HT_FREQ_1G_SUPPORT + select NORTHBRIDGE_AMD_AMDK8 + select NORTHBRIDGE_AMD_AMDK8_ROOT_COMPLEX + select SOUTHBRIDGE_VIA_VT8237R + select SOUTHBRIDGE_VIA_K8T890 + select SUPERIO_WINBOND_W83627EHG + select HAVE_OPTION_TABLE + select HAVE_ACPI_TABLES + select HAVE_MP_TABLE + select BOARD_ROMSIZE_KB_512 + select RAMINIT_SYSINFO + select QRANK_DIMM_SUPPORT + select SET_FIDVID + +config MAINBOARD_DIR + string + default asus/a8v-e_se + +config DCACHE_RAM_BASE + hex + default 0xcc000 + +config DCACHE_RAM_SIZE + hex + default 0x4000 + +config DCACHE_RAM_GLOBAL_VAR_SIZE + hex + default 0x1000 + +config APIC_ID_OFFSET + hex + default 0x10 + +config SB_HT_CHAIN_ON_BUS0 + int + default 1 + +config MAINBOARD_PART_NUMBER + string + default "A8V-E SE" + +config HW_MEM_HOLE_SIZEK + hex + default 0 + +config MAX_CPUS + int + default 2 + +config MAX_PHYSICAL_CPUS + int + default 1 + +config HEAP_SIZE + hex + default 0x40000 + +config HT_CHAIN_END_UNITID_BASE + hex + default 0x20 + +config HT_CHAIN_UNITID_BASE + hex + default 0x0 + +endif # BOARD_ASUS_A8V_E_SE diff --git a/src/mainboard/asus/k8v-x/acpi_tables.c b/src/mainboard/asus/k8v-x/acpi_tables.c new file mode 100644 index 0000000..218f3bb --- /dev/null +++ b/src/mainboard/asus/k8v-x/acpi_tables.c @@ -0,0 +1,175 @@ +/* + * This file is part of the coreboot project. + * + * Written by Stefan Reinauer <stepan(a)openbios.org>. + * ACPI FADT, FACS, and DSDT table support added by + * + * Copyright (C) 2004 Stefan Reinauer <stepan(a)openbios.org> + * Copyright (C) 2005 Nick Barker <nick.barker9(a)btinternet.com> + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <string.h> +#include <arch/acpi.h> +#include <arch/smp/mpspec.h> +#include <arch/ioapic.h> +#include <device/device.h> +#include <device/pci_ids.h> +#include "southbridge/via/vt8237r/vt8237r.h" +#include "southbridge/via/k8t890/k8t890.h" +#include "northbridge/amd/amdk8/acpi.h" +#include <cpu/amd/model_fxx_powernow.h> + +extern const unsigned char AmlCode[]; + +unsigned long acpi_fill_mcfg(unsigned long current) +{ + device_t dev; + struct resource *res; + + dev = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_K8T890CE_5, 0); + if (!dev) + return current; + + res = find_resource(dev, K8T890_MMCONFIG_MBAR); + if (res) { + current += acpi_create_mcfg_mmconfig((acpi_mcfg_mmconfig_t *) + current, res->base, 0x0, 0x0, 0xff); + } + return current; +} + +unsigned long acpi_fill_madt(unsigned long current) +{ + unsigned int gsi_base = 0x18; + + /* Create all subtables for processors. */ + current = acpi_create_madt_lapics(current); + + /* Write SB IOAPIC. */ + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, + VT8237R_APIC_ID, IO_APIC_ADDR, 0); + + /* Write NB IOAPIC. */ + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, + K8T890_APIC_ID, K8T890_APIC_BASE, gsi_base); + + /* IRQ9 ACPI active low. */ + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) + current, 0, 9, 9, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_LOW); + + /* IRQ0 -> APIC IRQ2. */ + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) + current, 0, 0, 2, 0x0); + + /* Create all subtables for processors. */ + current = acpi_create_madt_lapic_nmis(current, + MP_IRQ_TRIGGER_EDGE | MP_IRQ_POLARITY_HIGH, 1); + + return current; +} + +unsigned long acpi_fill_ssdt_generator(unsigned long current, const char *oem_table_id) +{ + k8acpi_write_vars(); + amd_model_fxx_generate_powernow(0, 0, 0); + acpigen_write_mainboard_resources("\\_SB.PCI0.MBRS", "_CRS"); + return (unsigned long) (acpigen_get_current()); +} + +unsigned long write_acpi_tables(unsigned long start) +{ + unsigned long current; + acpi_rsdp_t *rsdp; + acpi_srat_t *srat; + acpi_rsdt_t *rsdt; + acpi_madt_t *madt; + acpi_mcfg_t *mcfg; + acpi_fadt_t *fadt; + acpi_facs_t *facs; + acpi_header_t *ssdt; + acpi_header_t *dsdt; + + /* Align ACPI tables to 16 byte. */ + start = (start + 0x0f) & -0x10; + current = start; + + printk(BIOS_INFO, "ACPI: Writing ACPI tables at %lx...\n", start); + + /* We need at least an RSDP and an RSDT table. */ + rsdp = (acpi_rsdp_t *) current; + current += sizeof(acpi_rsdp_t); + rsdt = (acpi_rsdt_t *) current; + current += sizeof(acpi_rsdt_t); + + /* Clear all table memory. */ + memset((void *) start, 0, current - start); + + acpi_write_rsdp(rsdp, rsdt, NULL); + acpi_write_rsdt(rsdt); + + /* We explicitly add these tables later on: */ + printk(BIOS_DEBUG, "ACPI: * FACS\n"); + facs = (acpi_facs_t *) current; + current += sizeof(acpi_facs_t); + acpi_create_facs(facs); + + dsdt = (acpi_header_t *)current; + memcpy(dsdt, &AmlCode, sizeof(acpi_header_t)); + current += dsdt->length; + memcpy(dsdt, &AmlCode, dsdt->length); + dsdt->checksum = 0; /* Don't trust iasl to get this right. */ + dsdt->checksum = acpi_checksum((u8*)dsdt, dsdt->length); + printk(BIOS_DEBUG, "ACPI: * DSDT @ %p Length %x\n", dsdt, + dsdt->length); + printk(BIOS_DEBUG, "ACPI: * FADT\n"); + + fadt = (acpi_fadt_t *) current; + current += sizeof(acpi_fadt_t); + + acpi_create_fadt(fadt, facs, dsdt); + acpi_add_table(rsdp, fadt); + + /* If we want to use HPET timers Linux wants it in MADT. */ + printk(BIOS_DEBUG, "ACPI: * MADT\n"); + madt = (acpi_madt_t *) current; + acpi_create_madt(madt); + current += madt->header.length; + acpi_add_table(rsdp, madt); + printk(BIOS_DEBUG, "ACPI: * MCFG\n"); + mcfg = (acpi_mcfg_t *) current; + acpi_create_mcfg(mcfg); + current += mcfg->header.length; + acpi_add_table(rsdp, mcfg); + + printk(BIOS_DEBUG, "ACPI: * SRAT\n"); + srat = (acpi_srat_t *) current; + acpi_create_srat(srat); + current += srat->header.length; + acpi_add_table(rsdp, srat); + + /* SSDT */ + printk(BIOS_DEBUG, "ACPI: * SSDT\n"); + ssdt = (acpi_header_t *)current; + + acpi_create_ssdt_generator(ssdt, ACPI_TABLE_CREATOR); + current += ssdt->length; + acpi_add_table(rsdp, ssdt); + + printk(BIOS_INFO, "ACPI: done.\n"); + return current; +} diff --git a/src/mainboard/asus/k8v-x/chip.h b/src/mainboard/asus/k8v-x/chip.h new file mode 100644 index 0000000..c2849ef --- /dev/null +++ b/src/mainboard/asus/k8v-x/chip.h @@ -0,0 +1,22 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +extern struct chip_operations mainboard_ops; + +struct mainboard_config {}; diff --git a/src/mainboard/asus/k8v-x/cmos.layout b/src/mainboard/asus/k8v-x/cmos.layout new file mode 100644 index 0000000..fc13a3c --- /dev/null +++ b/src/mainboard/asus/k8v-x/cmos.layout @@ -0,0 +1,98 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +395 1 e 1 hw_scrubber +396 1 e 1 interleave_chip_selects +397 2 e 8 max_mem_clock +399 1 e 2 multi_core +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +440 4 e 9 slow_cpu +444 1 e 1 nmi +445 1 e 1 iommu +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 amd_reserved + + + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM +8 0 DDR400 +8 1 DDR333 +8 2 DDR266 +8 3 DDR200 +9 0 off +9 1 87.5% +9 2 75.0% +9 3 62.5% +9 4 50.0% +9 5 37.5% +9 6 25.0% +9 7 12.5% + +checksums + +checksum 392 983 984 + + diff --git a/src/mainboard/asus/k8v-x/devicetree.cb b/src/mainboard/asus/k8v-x/devicetree.cb new file mode 100644 index 0000000..3da93fe --- /dev/null +++ b/src/mainboard/asus/k8v-x/devicetree.cb @@ -0,0 +1,97 @@ +chip northbridge/amd/amdk8/root_complex # Root complex + device lapic_cluster 0 on # APIC cluster + chip cpu/amd/socket_939 # CPU + device lapic 0 on end # APIC + end + end + device pci_domain 0 on # PCI domain + subsystemid 0x1043 0 inherit + chip northbridge/amd/amdk8 # mc0 + device pci 18.0 on # Northbridge + # Devices on link 0, link 0 == LDT 0 + chip southbridge/via/vt8237r # Southbridge + register "ide0_enable" = "1" # Enable IDE channel 0 + register "ide1_enable" = "1" # Enable IDE channel 1 + register "ide0_80pin_cable" = "1" # 80pin cable on IDE channel 0 + register "ide1_80pin_cable" = "1" # 80pin cable on IDE channel 1 + register "fn_ctrl_lo" = "0" # Enable SB functions + register "fn_ctrl_hi" = "0xad" # Enable SB functions + device pci 0.0 on end # HT + device pci f.1 on end # IDE + device pci 11.0 on # LPC + chip drivers/generic/generic # DIMM 0-0-0 + device i2c 50 on end + end + chip drivers/generic/generic # DIMM 0-0-1 + device i2c 51 on end + end + chip drivers/generic/generic # DIMM 0-1-0 + device i2c 52 on end + end + chip drivers/generic/generic # DIMM 0-1-1 + device i2c 53 on end + end + chip superio/winbond/w83627ehg # Super I/O + device pnp 2e.0 on # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 on # Parallel port + io 0x60 = 0x378 + irq 0x70 = 7 + drq 0x74 = 3 + end + device pnp 2e.2 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.3 off # Com2 (N/A on this board) + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.5 off # PS/2 keyboard & mouse (off) + end + device pnp 2e.106 off # Serial flash interface (SFI) + io 0x60 = 0x100 + end + device pnp 2e.007 off # GPIO 1 + end + device pnp 2e.107 on # Game port + io 0x60 = 0x201 + end + device pnp 2e.207 on # MIDI + io 0x62 = 0x330 + irq 0x70 = 0xa + end + device pnp 2e.307 off # GPIO 6 + end + device pnp 2e.8 off # WDTO#, PLED + end + device pnp 2e.009 on # GPIO 2 + end + device pnp 2e.109 off # GPIO 3 + end + device pnp 2e.209 off # GPIO 4 + end + device pnp 2e.309 on # GPIO 5 + end + device pnp 2e.a off # ACPI + end + device pnp 2e.b on # Hardware monitor + io 0x60 = 0x290 + irq 0x70 = 0 + end + end + end + device pci 12.0 off end # VIA LAN (off, other chip used) + end + chip southbridge/via/k8t890 # "Southbridge" K8T890 + end + end + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end + end +end diff --git a/src/mainboard/asus/k8v-x/dsdt.asl b/src/mainboard/asus/k8v-x/dsdt.asl new file mode 100644 index 0000000..16ad92c --- /dev/null +++ b/src/mainboard/asus/k8v-x/dsdt.asl @@ -0,0 +1,249 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2004 Nick Barker <Nick.Barker9(a)btinternet.com> + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* + * ISA portions taken from QEMU acpi-dsdt.dsl. + */ + +DefinitionBlock ("DSDT.aml", "DSDT", 1, "CORE ", "COREBOOT", 1) +{ + #include "northbridge/amd/amdk8/util.asl" + + /* For now only define 2 power states: + * - S0 which is fully on + * - S5 which is soft off + * Any others would involve declaring the wake up methods. + */ + Name (\_S0, Package () { 0x00, 0x00, 0x00, 0x00 }) + Name (\_S5, Package () { 0x02, 0x02, 0x00, 0x00 }) + + /* Root of the bus hierarchy */ + Scope (\_SB) + { + /* Top PCI device */ + Device (PCI0) + { + Name (_HID, EisaId ("PNP0A03")) + Name (_ADR, 0x00) + Name (_UID, 0x00) + Name (_BBN, 0x00) + + External (BUSN) + External (MMIO) + External (PCIO) + External (SBLK) + External (TOM1) + External (HCLK) + External (SBDN) + External (HCDN) + + Method (_CRS, 0, NotSerialized) + { + Name (BUF0, ResourceTemplate () + { + IO (Decode16, + 0x0CF8, // Address Range Minimum + 0x0CF8, // Address Range Maximum + 0x01, // Address Alignment + 0x08, // Address Length + ) + WordIO (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange, + 0x0000, // Address Space Granularity + 0x0000, // Address Range Minimum + 0x0CF7, // Address Range Maximum + 0x0000, // Address Translation Offset + 0x0CF8, // Address Length + ,, , TypeStatic) + }) + /* Methods bellow use SSDT to get actual MMIO regs + The IO ports are from 0xd00, optionally an VGA, + otherwise the info from MMIO is used. + */ + Concatenate (\_SB.GMEM (0x00, \_SB.PCI0.SBLK), BUF0, Local1) + Concatenate (\_SB.GIOR (0x00, \_SB.PCI0.SBLK), Local1, Local2) + Concatenate (\_SB.GWBN (0x00, \_SB.PCI0.SBLK), Local2, Local3) + Return (Local3) + } + + /* PCI Routing Table */ + Name (_PRT, Package () { + Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, /* Slot 0xB */ + Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 }, + Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 }, + Package (0x04) { 0x000BFFFF, 0x03, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x00, 0x00, 0x11 }, /* Slot 0xC */ + Package (0x04) { 0x000CFFFF, 0x01, 0x00, 0x12 }, + Package (0x04) { 0x000CFFFF, 0x02, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x03, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x00, 0x00, 0x12 }, /* Slot 0xD */ + Package (0x04) { 0x000DFFFF, 0x01, 0x00, 0x13 }, + Package (0x04) { 0x000DFFFF, 0x02, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x03, 0x00, 0x11 }, + Package (0x04) { 0x000FFFFF, 0x01, 0x00, 0x14 }, /* 0xf SATA IRQ 20 */ + Package (0x04) { 0x000FFFFF, 0x00, 0x00, 0x14 }, /* 0xf Native IDE IRQ 20 */ + Package (0x04) { 0x0010FFFF, 0x00, 0x00, 0x15 }, /* USB routing */ + Package (0x04) { 0x0010FFFF, 0x01, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x02, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x03, 0x00, 0x15 }, + Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 }, /* AC97, MC97 */ + Package (0x04) { 0x0002FFFF, 0x00, 0x00, 0x1B }, /* PCIE16 bridge IRQ27 */ + Package (0x04) { 0x0002FFFF, 0x01, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x02, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x03, 0x00, 0x1B }, + Package (0x04) { 0x0003FFFF, 0x00, 0x00, 0x1F }, /* PCIE bridge IRQ31 */ + Package (0x04) { 0x0003FFFF, 0x01, 0x00, 0x23 }, /* IRQ36 */ + Package (0x04) { 0x0003FFFF, 0x02, 0x00, 0x27 }, /* IRQ39 */ + Package (0x04) { 0x0003FFFF, 0x03, 0x00, 0x2B } /* IRQ43 */ + }) + + Device (PEGG) + { + Name (_ADR, 0x00020000) + Name (_UID, 0x00) + Name (_BBN, 0x02) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x18 }, /* PCIE IRQ24-IRQ27 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x19 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1B }, + }) + } + + Device (PEX0) + { + Name (_ADR, 0x00030000) + Name (_UID, 0x00) + Name (_BBN, 0x03) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x1C }, /* PCIE IRQ28-IRQ31 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x1D }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1E }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1F }, + }) + } + + Device (PEX1) + { + Name (_ADR, 0x00030001) + Name (_UID, 0x00) + Name (_BBN, 0x04) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x20 }, /* PCIE IRQ32-IRQ35 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x21 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x22 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x23 }, + }) + } + + Device (PEX2) + { + Name (_ADR, 0x00030002) + Name (_UID, 0x00) + Name (_BBN, 0x05) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x24 }, /* PCIE IRQ36-IRQ39 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x25 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x26 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x27 }, + }) + } + + Device (PEX3) + { + Name (_ADR, 0x00030003) + Name (_UID, 0x00) + Name (_BBN, 0x06) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x28 }, /* PCIE IRQ40-IRQ43 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x29 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x2A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x2B }, + }) + } + + Device (ISA) { + Name (_ADR, 0x00110000) + + /* PS/2 keyboard (seems to be important for WinXP install) */ + Device (KBD) + { + Name (_HID, EisaId ("PNP0303")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () { + IO (Decode16, 0x0060, 0x0060, 0x01, 0x01) + IO (Decode16, 0x0064, 0x0064, 0x01, 0x01) + IRQNoFlags () {1} + }) + Return (TMP) + } + } + + /* PS/2 mouse */ + Device (MOU) + { + Name (_HID, EisaId ("PNP0F13")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () { + IRQNoFlags () {12} + }) + Return (TMP) + } + } + + /* PS/2 floppy controller */ + Device (FDC0) + { + Name (_HID, EisaId ("PNP0700")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (BUF0, ResourceTemplate () { + IO (Decode16, 0x03F2, 0x03F2, 0x00, 0x04) + IO (Decode16, 0x03F7, 0x03F7, 0x00, 0x01) + IRQNoFlags () {6} + DMA (Compatibility, NotBusMaster, Transfer8) {2} + }) + Return (BUF0) + } + } + } + /* Dummy device to hold auto generated reserved resources */ + Device(MBRS) { + Name (_HID, EisaId ("PNP0C02")) + Name (_UID, 0x01) + External(_CRS) /* Resource Template in SSDT */ + } + + } + } +} diff --git a/src/mainboard/asus/k8v-x/mainboard.c b/src/mainboard/asus/k8v-x/mainboard.c new file mode 100644 index 0000000..b70f396 --- /dev/null +++ b/src/mainboard/asus/k8v-x/mainboard.c @@ -0,0 +1,28 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "chip.h" + +struct chip_operations mainboard_ops = { + CHIP_NAME("ASUS A8V-E SE Mainboard") +}; diff --git a/src/mainboard/asus/k8v-x/mptable.c b/src/mainboard/asus/k8v-x/mptable.c new file mode 100644 index 0000000..999dd6c --- /dev/null +++ b/src/mainboard/asus/k8v-x/mptable.c @@ -0,0 +1,116 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <string.h> +#include <stdint.h> +#include <arch/smp/mpspec.h> +#include <arch/ioapic.h> +#include "southbridge/via/vt8237r/vt8237r.h" +#include "southbridge/via/k8t890/k8t890.h" + +static void *smp_write_config_table(void *v) +{ + struct mp_config_table *mc; + int bus_isa; + + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + + mptable_init(mc, LAPIC_ADDR); + + smp_write_processors(mc); + + mptable_write_buses(mc, NULL, &bus_isa); + + /* I/O APICs: APIC ID Version State Address */ + smp_write_ioapic(mc, VT8237R_APIC_ID, 0x20, IO_APIC_ADDR); + smp_write_ioapic(mc, K8T890_APIC_ID, 0x20, K8T890_APIC_BASE); + + mptable_add_isa_interrupts(mc, bus_isa, VT8237R_APIC_ID, 0); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 0, VT8237R_APIC_ID, 0x10); //IRQ16 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 1, VT8237R_APIC_ID, 0x11); //IRQ17 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 2, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 3, VT8237R_APIC_ID, 0x13); //IRQ19 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 0, VT8237R_APIC_ID, 0x11); //IRQ17 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 1, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 2, VT8237R_APIC_ID, 0x13); //IRQ19 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 3, VT8237R_APIC_ID, 0x10); //IRQ16 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 0, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 1, VT8237R_APIC_ID, 0x13); //IRQ19 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 2, VT8237R_APIC_ID, 0x10); //IRQ16 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 3, VT8237R_APIC_ID, 0x11); //IRQ17 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xf << 2) | 0, VT8237R_APIC_ID, 0x14); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xf << 2) | 1, VT8237R_APIC_ID, 0x14); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 0, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 1, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 2, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x11 << 2) | 2, VT8237R_APIC_ID, 0x16); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 0, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 1, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 2, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 3, K8T890_APIC_ID, 0x3); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 0, K8T890_APIC_ID, 0x7); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 1, K8T890_APIC_ID, 0xb); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 2, K8T890_APIC_ID, 0xf); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 3, K8T890_APIC_ID, 0x13); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 0, K8T890_APIC_ID, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 1, K8T890_APIC_ID, 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 2, K8T890_APIC_ID, 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 3, K8T890_APIC_ID, 0x3); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 0, K8T890_APIC_ID, 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 1, K8T890_APIC_ID, 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 2, K8T890_APIC_ID, 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 3, K8T890_APIC_ID, 0x7); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 0, K8T890_APIC_ID, 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 1, K8T890_APIC_ID, 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 2, K8T890_APIC_ID, 0xa); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 3, K8T890_APIC_ID, 0xb); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 0, K8T890_APIC_ID, 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 1, K8T890_APIC_ID, 0xd); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 2, K8T890_APIC_ID, 0xe); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 3, K8T890_APIC_ID, 0xf); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 0, K8T890_APIC_ID, 0x10); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 1, K8T890_APIC_ID, 0x11); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 2, K8T890_APIC_ID, 0x12); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 3, K8T890_APIC_ID, 0x13); + + /* Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ + mptable_lintsrc(mc, bus_isa); + /* There is no extension information... */ + + /* Compute the checksums. */ + return mptable_finalize(mc); +} + +unsigned long write_smp_table(unsigned long addr) +{ + void *v; + v = smp_write_floating_table(addr, 0); + return (unsigned long)smp_write_config_table(v); +} diff --git a/src/mainboard/asus/k8v-x/romstage.c b/src/mainboard/asus/k8v-x/romstage.c new file mode 100644 index 0000000..4e08859 --- /dev/null +++ b/src/mainboard/asus/k8v-x/romstage.c @@ -0,0 +1,225 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2006 AMD + * (Written by Yinghai Lu <yinghailu(a)amd.com> for AMD) + * Copyright (C) 2006 MSI + * (Written by Bingxun Shi <bingxunshi(a)gmail.com> for MSI) + * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +unsigned int get_sbdn(unsigned bus); + +#include <stdint.h> +#include <string.h> +#include <device/pci_def.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <cpu/x86/lapic.h> +#include <pc80/mc146818rtc.h> +#include <console/console.h> +#include <cpu/amd/model_fxx_rev.h> +#include "northbridge/amd/amdk8/raminit.h" +#include "cpu/amd/model_fxx/apic_timer.c" +#include "lib/delay.c" +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/amd/amdk8/reset_test.c" +#include "northbridge/amd/amdk8/early_ht.c" +#include "superio/winbond/w83627ehg/early_serial.c" +#include "southbridge/via/vt8237r/early_smbus.c" +#include "northbridge/amd/amdk8/debug.c" /* After vt8237r/early_smbus.c! */ +#include "cpu/x86/mtrr/earlymtrr.c" +#include "cpu/x86/bist.h" +#include "northbridge/amd/amdk8/setup_resource_map.c" +#include <spd.h> + +#define SERIAL_DEV PNP_DEV(0x2e, W83627EHG_SP1) +#define GPIO_DEV PNP_DEV(0x2e, W83627EHG_GPIO_SUSLED_V) +#define ACPI_DEV PNP_DEV(0x2e, W83627EHG_ACPI) + +static void memreset(int controllers, const struct mem_controller *ctrl) { } +static void activate_spd_rom(const struct mem_controller *ctrl) { } + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#include <reset.h> +void soft_reset(void) +{ + uint8_t tmp; + + set_bios_reset(); + print_debug("soft reset \n"); + + /* PCI reset */ + tmp = pci_read_config8(PCI_DEV(0, 0x11, 0), 0x4f); + tmp |= 0x01; + pci_write_config8(PCI_DEV(0, 0x11, 0), 0x4f, tmp); + + while (1) { + /* daisy daisy ... */ + hlt(); + } +} + +#include "southbridge/via/k8t890/early_car.c" +#include "northbridge/amd/amdk8/amdk8.h" +#include "northbridge/amd/amdk8/incoherent_ht.c" +#include "northbridge/amd/amdk8/coherent_ht.c" +#include "northbridge/amd/amdk8/raminit.c" +#include "lib/generic_sdram.c" +#include "cpu/amd/dualcore/dualcore.c" +#include "cpu/amd/car/post_cache_as_ram.c" +#include "cpu/amd/model_fxx/init_cpus.c" +#include "cpu/amd/model_fxx/fidvid.c" +#include "northbridge/amd/amdk8/resourcemap.c" + +unsigned int get_sbdn(unsigned bus) +{ + device_t dev; + + dev = pci_locate_device_on_bus(PCI_ID(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_VT8237R_LPC), bus); + return (dev >> 15) & 0x1f; +} + +static void sio_init(void) +{ + u8 reg; + + pnp_enter_ext_func_mode(SERIAL_DEV); + /* We have 24MHz input. */ + reg = pnp_read_config(SERIAL_DEV, 0x24); + pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); + /* We have GPIO for KB/MS pin. */ + reg = pnp_read_config(SERIAL_DEV, 0x2a); + pnp_write_config(SERIAL_DEV, 0x2a, (reg | 1)); + /* We have all RESTOUT and even some reserved bits, too. */ + reg = pnp_read_config(SERIAL_DEV, 0x2c); + pnp_write_config(SERIAL_DEV, 0x2c, (reg | 0xf0)); + pnp_exit_ext_func_mode(SERIAL_DEV); + + pnp_enter_ext_func_mode(ACPI_DEV); + pnp_set_logical_device(ACPI_DEV); + /* + * Set the delay rising time from PWROK_LP to PWROK_ST to + * 300 - 600ms, and 0 to vice versa. + */ + reg = pnp_read_config(ACPI_DEV, 0xe6); + pnp_write_config(ACPI_DEV, 0xe6, (reg & 0xf0)); + /* 1 Use external suspend clock source 32.768KHz. Undocumented?? */ + reg = pnp_read_config(ACPI_DEV, 0xe4); + pnp_write_config(ACPI_DEV, 0xe4, (reg | 0x10)); + pnp_exit_ext_func_mode(ACPI_DEV); + + pnp_enter_ext_func_mode(GPIO_DEV); + pnp_set_logical_device(GPIO_DEV); + /* Set memory voltage to 2.75V, vcore offset + 100mV, 1.5V chipset voltage. */ + pnp_write_config(GPIO_DEV, 0x30, 0x09); /* Enable GPIO 2 & GPIO 5. */ + pnp_write_config(GPIO_DEV, 0xe2, 0x00); /* No inversion */ + pnp_write_config(GPIO_DEV, 0xe5, 0x00); /* No inversion */ + pnp_write_config(GPIO_DEV, 0xe3, 0x03); /* 0000 0011, 0=output 1=input */ + pnp_write_config(GPIO_DEV, 0xe0, 0xde); /* 1101 1110, 0=output 1=input */ + pnp_write_config(GPIO_DEV, 0xe1, 0x01); /* Set output val. */ + pnp_write_config(GPIO_DEV, 0xe4, 0xb4); /* Set output val (1011 0100). */ + pnp_exit_ext_func_mode(GPIO_DEV); +} + +void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + static const uint16_t spd_addr[] = { + // Node 0 + DIMM0, DIMM2, 0, 0, + DIMM1, DIMM3, 0, 0, + // Node 1 + DIMM4, DIMM6, 0, 0, + DIMM5, DIMM7, 0, 0, + }; + unsigned bsp_apicid = 0; + int needs_reset = 0; + struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); + + sio_init(); + w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); + console_init(); + enable_rom_decode(); + + print_info("now booting... fallback\n"); + + /* Is this a CPU only reset? Or is this a secondary CPU? */ + if (!cpu_init_detectedx && boot_cpu()) { + /* Nothing special needs to be done to find bus 0. */ + /* Allow the HT devices to be found. */ + enumerate_ht_chain(); + } + + // FIXME why is this executed again? ---> + sio_init(); + w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); + console_init(); + enable_rom_decode(); + // <--- FIXME why is this executed again? + + print_info("now booting... real_main\n"); + + if (bist == 0) + bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); + + /* Halt if there was a built in self test failure. */ + report_bist_failure(bist); + + setup_default_resource_map(); + setup_coherent_ht_domain(); + wait_all_core0_started(); + + print_info("now booting... Core0 started\n"); + +#if CONFIG_LOGICAL_CPUS==1 + /* It is said that we should start core1 after all core0 launched. */ + start_other_cores(); + wait_all_other_cores_started(bsp_apicid); +#endif + init_timer(); + ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */ + + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); + needs_reset |= k8t890_early_setup_ht(); + + if (needs_reset) { + print_debug("ht reset -\n"); + soft_reset(); + } + + /* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */ + enable_fid_change(); + init_fidvid_bsp(bsp_apicid); + + /* Stop the APs so we can start them later in init. */ + allow_all_aps_stop(bsp_apicid); + + /* It's the time to set ctrl now. */ + fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); + + enable_smbus(); + sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); + post_cache_as_ram(); +}

1 0

Patch set updated for coreboot: 2e725e2 adding support for the Asus K8V-X
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/390 -gerrit commit 2e725e2c4399c177f7371de0b567c7e3328f9b5b Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:41 2011 +0100 adding support for the Asus K8V-X This pulls it all together and adds the real board-specific code. Confirmed to be working: - IDE - SATA - floppy - USB1.1 - USB2.0 - PS/2 keyboard - PS/2 mouse - serial - parport - sound - ethernet - PCI slots - AGP - powernow - fan speed monitoring Change-Id: Ifb97714c2f009d688be0ca3c38ddc01599ffd799 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/mainboard/asus/Kconfig | 3 + src/mainboard/asus/k8v-x/Kconfig | 22 +++++--- src/mainboard/asus/k8v-x/acpi_tables.c | 2 +- src/mainboard/asus/k8v-x/devicetree.cb | 51 ++++++++++--------- src/mainboard/asus/k8v-x/dsdt.asl | 87 ++++--------------------------- src/mainboard/asus/k8v-x/mainboard.c | 38 +++++++++++++- src/mainboard/asus/k8v-x/mptable.c | 2 +- src/mainboard/asus/k8v-x/romstage.c | 69 +++++++++---------------- 8 files changed, 117 insertions(+), 157 deletions(-) diff --git a/src/mainboard/asus/Kconfig b/src/mainboard/asus/Kconfig index 77b7997..46c4ac1 100644 --- a/src/mainboard/asus/Kconfig +++ b/src/mainboard/asus/Kconfig @@ -27,6 +27,8 @@ config BOARD_ASUS_A8V_E_SE bool "A8V-E SE" config BOARD_ASUS_A8V_E_DELUXE bool "A8V-E Deluxe" +config BOARD_ASUS_K8V_X + bool "K8V-X" config BOARD_ASUS_M2N_E bool "M2N-E" config BOARD_ASUS_M2V @@ -61,6 +63,7 @@ endchoice source "src/mainboard/asus/a8n_e/Kconfig" source "src/mainboard/asus/a8v-e_se/Kconfig" source "src/mainboard/asus/a8v-e_deluxe/Kconfig" +source "src/mainboard/asus/k8v-x/Kconfig" source "src/mainboard/asus/m2n-e/Kconfig" source "src/mainboard/asus/m2v/Kconfig" source "src/mainboard/asus/m2v-mx_se/Kconfig" diff --git a/src/mainboard/asus/k8v-x/Kconfig b/src/mainboard/asus/k8v-x/Kconfig index 4975cfa..31d8564 100644 --- a/src/mainboard/asus/k8v-x/Kconfig +++ b/src/mainboard/asus/k8v-x/Kconfig @@ -1,26 +1,26 @@ -if BOARD_ASUS_A8V_E_SE +if BOARD_ASUS_K8V_X config BOARD_SPECIFIC_OPTIONS # dummy def_bool y select ARCH_X86 - select CPU_AMD_SOCKET_939 - select K8_HT_FREQ_1G_SUPPORT + select CPU_AMD_SOCKET_754 select NORTHBRIDGE_AMD_AMDK8 select NORTHBRIDGE_AMD_AMDK8_ROOT_COMPLEX select SOUTHBRIDGE_VIA_VT8237R - select SOUTHBRIDGE_VIA_K8T890 - select SUPERIO_WINBOND_W83627EHG + select SOUTHBRIDGE_VIA_K8T800_OLD + select SUPERIO_WINBOND_W83697HF select HAVE_OPTION_TABLE select HAVE_ACPI_TABLES select HAVE_MP_TABLE select BOARD_ROMSIZE_KB_512 select RAMINIT_SYSINFO - select QRANK_DIMM_SUPPORT select SET_FIDVID + select K8_DQ_DRIVE_STRENGTH_0 + select VT8237R_ON_AFTER_POWER_LOSS config MAINBOARD_DIR string - default asus/a8v-e_se + default asus/k8v-x config DCACHE_RAM_BASE hex @@ -44,7 +44,11 @@ config SB_HT_CHAIN_ON_BUS0 config MAINBOARD_PART_NUMBER string - default "A8V-E SE" + default "K8V-X" + +config AGP_APERTURE_SIZE + hex + default 0x10000000 config HW_MEM_HOLE_SIZEK hex @@ -70,4 +74,4 @@ config HT_CHAIN_UNITID_BASE hex default 0x0 -endif # BOARD_ASUS_A8V_E_SE +endif # BOARD_ASUS_K8V_X diff --git a/src/mainboard/asus/k8v-x/acpi_tables.c b/src/mainboard/asus/k8v-x/acpi_tables.c index 218f3bb..571d136 100644 --- a/src/mainboard/asus/k8v-x/acpi_tables.c +++ b/src/mainboard/asus/k8v-x/acpi_tables.c @@ -30,7 +30,7 @@ #include <device/device.h> #include <device/pci_ids.h> #include "southbridge/via/vt8237r/vt8237r.h" -#include "southbridge/via/k8t890/k8t890.h" +#include "southbridge/via/k8t890/k8x8xx.h" #include "northbridge/amd/amdk8/acpi.h" #include <cpu/amd/model_fxx_powernow.h> diff --git a/src/mainboard/asus/k8v-x/devicetree.cb b/src/mainboard/asus/k8v-x/devicetree.cb index 3da93fe..20d1959 100644 --- a/src/mainboard/asus/k8v-x/devicetree.cb +++ b/src/mainboard/asus/k8v-x/devicetree.cb @@ -1,6 +1,6 @@ chip northbridge/amd/amdk8/root_complex # Root complex device lapic_cluster 0 on # APIC cluster - chip cpu/amd/socket_939 # CPU + chip cpu/amd/socket_754 # CPU device lapic 0 on end # APIC end end @@ -16,8 +16,26 @@ chip northbridge/amd/amdk8/root_complex # Root complex register "ide1_80pin_cable" = "1" # 80pin cable on IDE channel 1 register "fn_ctrl_lo" = "0" # Enable SB functions register "fn_ctrl_hi" = "0xad" # Enable SB functions + register "usb2_termination_set" = "1" + register "usb2_termination_a" = "8" + register "usb2_termination_b" = "8" + register "usb2_termination_c" = "6" + register "usb2_termination_d" = "6" + register "usb2_termination_e" = "6" + register "usb2_termination_f" = "6" + register "usb2_termination_g" = "6" + register "usb2_termination_h" = "6" + register "usb2_dpll_set" = "1" + register "usb2_dpll_delay" = "3" + register "no_int_efgh" = "1" + register "enable_gpo3" = "1" + register "disable_gpo26_gpo27" = "1" + register "enable_aol_2_smb_slave" = "1" + register "enable_gpo5" = "1" + register "gpio15_12_dir_output" = "1" device pci 0.0 on end # HT device pci f.1 on end # IDE + device pci 10.4 on end # USB2 device pci 11.0 on # LPC chip drivers/generic/generic # DIMM 0-0-0 device i2c 50 on end @@ -28,10 +46,9 @@ chip northbridge/amd/amdk8/root_complex # Root complex chip drivers/generic/generic # DIMM 0-1-0 device i2c 52 on end end - chip drivers/generic/generic # DIMM 0-1-1 - device i2c 53 on end - end - chip superio/winbond/w83627ehg # Super I/O + chip superio/winbond/w83697hf # Super I/O + register "hwmon_fan1_divisor" = "128" + register "hwmon_fan2_divisor" = "4" device pnp 2e.0 on # Floppy io 0x60 = 0x3f0 irq 0x70 = 6 @@ -47,35 +64,19 @@ chip northbridge/amd/amdk8/root_complex # Root complex irq 0x70 = 4 end device pnp 2e.3 off # Com2 (N/A on this board) - io 0x60 = 0x2f8 - irq 0x70 = 3 - end - device pnp 2e.5 off # PS/2 keyboard & mouse (off) - end - device pnp 2e.106 off # Serial flash interface (SFI) - io 0x60 = 0x100 end - device pnp 2e.007 off # GPIO 1 + device pnp 2e.6 off # CIR end - device pnp 2e.107 on # Game port - io 0x60 = 0x201 + device pnp 2e.7 off # Game port/GPIO 1 end - device pnp 2e.207 on # MIDI - io 0x62 = 0x330 - irq 0x70 = 0xa + device pnp 2e.8 off # MIDI/GPIO 5 end - device pnp 2e.307 off # GPIO 6 - end - device pnp 2e.8 off # WDTO#, PLED - end - device pnp 2e.009 on # GPIO 2 + device pnp 2e.009 off # GPIO 2 end device pnp 2e.109 off # GPIO 3 end device pnp 2e.209 off # GPIO 4 end - device pnp 2e.309 on # GPIO 5 - end device pnp 2e.a off # ACPI end device pnp 2e.b on # Hardware monitor diff --git a/src/mainboard/asus/k8v-x/dsdt.asl b/src/mainboard/asus/k8v-x/dsdt.asl index 16ad92c..25b7460 100644 --- a/src/mainboard/asus/k8v-x/dsdt.asl +++ b/src/mainboard/asus/k8v-x/dsdt.asl @@ -84,6 +84,8 @@ DefinitionBlock ("DSDT.aml", "DSDT", 1, "CORE ", "COREBOOT", 1) /* PCI Routing Table */ Name (_PRT, Package () { + Package (0x04) { 0x0001FFFF, 0x00, 0x00, 0x10 }, /* AGP slot, effectively */ + Package (0x04) { 0x0001FFFF, 0x01, 0x00, 0x11 }, Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, /* Slot 0xB */ Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 }, Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 }, @@ -96,88 +98,23 @@ DefinitionBlock ("DSDT.aml", "DSDT", 1, "CORE ", "COREBOOT", 1) Package (0x04) { 0x000DFFFF, 0x01, 0x00, 0x13 }, Package (0x04) { 0x000DFFFF, 0x02, 0x00, 0x10 }, Package (0x04) { 0x000DFFFF, 0x03, 0x00, 0x11 }, + Package (0x04) { 0x000EFFFF, 0x00, 0x00, 0x13 }, /* Slot 0xE */ + Package (0x04) { 0x000EFFFF, 0x01, 0x00, 0x10 }, + Package (0x04) { 0x000EFFFF, 0x02, 0x00, 0x11 }, + Package (0x04) { 0x000EFFFF, 0x03, 0x00, 0x12 }, + Package (0x04) { 0x0009FFFF, 0x00, 0x00, 0x10 }, /* Slot 0x9 */ + Package (0x04) { 0x0009FFFF, 0x01, 0x00, 0x11 }, + Package (0x04) { 0x0009FFFF, 0x02, 0x00, 0x12 }, + Package (0x04) { 0x0009FFFF, 0x03, 0x00, 0x13 }, + Package (0x04) { 0x000AFFFF, 0x00, 0x00, 0x11 }, /* Marvell 88E8001 ethernet */ Package (0x04) { 0x000FFFFF, 0x01, 0x00, 0x14 }, /* 0xf SATA IRQ 20 */ Package (0x04) { 0x000FFFFF, 0x00, 0x00, 0x14 }, /* 0xf Native IDE IRQ 20 */ Package (0x04) { 0x0010FFFF, 0x00, 0x00, 0x15 }, /* USB routing */ Package (0x04) { 0x0010FFFF, 0x01, 0x00, 0x15 }, Package (0x04) { 0x0010FFFF, 0x02, 0x00, 0x15 }, - Package (0x04) { 0x0010FFFF, 0x03, 0x00, 0x15 }, - Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 }, /* AC97, MC97 */ - Package (0x04) { 0x0002FFFF, 0x00, 0x00, 0x1B }, /* PCIE16 bridge IRQ27 */ - Package (0x04) { 0x0002FFFF, 0x01, 0x00, 0x1B }, - Package (0x04) { 0x0002FFFF, 0x02, 0x00, 0x1B }, - Package (0x04) { 0x0002FFFF, 0x03, 0x00, 0x1B }, - Package (0x04) { 0x0003FFFF, 0x00, 0x00, 0x1F }, /* PCIE bridge IRQ31 */ - Package (0x04) { 0x0003FFFF, 0x01, 0x00, 0x23 }, /* IRQ36 */ - Package (0x04) { 0x0003FFFF, 0x02, 0x00, 0x27 }, /* IRQ39 */ - Package (0x04) { 0x0003FFFF, 0x03, 0x00, 0x2B } /* IRQ43 */ + Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 } /* AC97, MC97 */ }) - Device (PEGG) - { - Name (_ADR, 0x00020000) - Name (_UID, 0x00) - Name (_BBN, 0x02) - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x18 }, /* PCIE IRQ24-IRQ27 */ - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x19 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1A }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1B }, - }) - } - - Device (PEX0) - { - Name (_ADR, 0x00030000) - Name (_UID, 0x00) - Name (_BBN, 0x03) - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x1C }, /* PCIE IRQ28-IRQ31 */ - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x1D }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1E }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1F }, - }) - } - - Device (PEX1) - { - Name (_ADR, 0x00030001) - Name (_UID, 0x00) - Name (_BBN, 0x04) - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x20 }, /* PCIE IRQ32-IRQ35 */ - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x21 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x22 }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x23 }, - }) - } - - Device (PEX2) - { - Name (_ADR, 0x00030002) - Name (_UID, 0x00) - Name (_BBN, 0x05) - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x24 }, /* PCIE IRQ36-IRQ39 */ - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x25 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x26 }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x27 }, - }) - } - - Device (PEX3) - { - Name (_ADR, 0x00030003) - Name (_UID, 0x00) - Name (_BBN, 0x06) - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x28 }, /* PCIE IRQ40-IRQ43 */ - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x29 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x2A }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x2B }, - }) - } - Device (ISA) { Name (_ADR, 0x00110000) diff --git a/src/mainboard/asus/k8v-x/mainboard.c b/src/mainboard/asus/k8v-x/mainboard.c index b70f396..3e294b8 100644 --- a/src/mainboard/asus/k8v-x/mainboard.c +++ b/src/mainboard/asus/k8v-x/mainboard.c @@ -2,6 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2007 Rudolf Marek <r.marek(a)assembler.cz> + * Copyright (C) 2010 Tobias Diedrich <ranma+coreboot(a)tdiedrich.de> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -21,8 +22,43 @@ #include <device/device.h> #include <device/pci.h> #include <device/pci_ids.h> +#include <arch/io.h> +#include "southbridge/via/vt8237r/vt8237r.h" #include "chip.h" +u32 vt8237_ide_80pin_detect(struct device *dev) +{ + device_t lpc_dev; + u16 acpi_io_base; + u32 gpio_in; + u32 res; + + lpc_dev = dev_find_device(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_VT8237R_LPC, 0); + if (!lpc_dev) + return 0; + + acpi_io_base = pci_read_config16(lpc_dev, 0x88) & ~1; + if (!acpi_io_base) + return 0; + + /* select function GPIO29 for pin AB9 */ + pci_write_config8(lpc_dev, 0xe5, pci_read_config8(lpc_dev, 0xe5) | 0x08); + + gpio_in = inl(acpi_io_base + 0x48); + /* bit 29 for primary port, clear if unconnected or 80-pin cable */ + res = gpio_in & (1<<29) ? 0 : VT8237R_IDE0_80PIN_CABLE; + /* bit 8 for secondary port, clear if unconnected or 80-pin cable */ + res |= gpio_in & (1<<8) ? 0 : VT8237R_IDE1_80PIN_CABLE; + + printk(BIOS_INFO, "Cable on %s PATA port: %d pin\n", "primary", + res & VT8237R_IDE0_80PIN_CABLE ? 80 : 40); + printk(BIOS_INFO, "Cable on %s PATA port: %d pin\n", "secondary", + res & VT8237R_IDE1_80PIN_CABLE ? 80 : 40); + + return res; +} + struct chip_operations mainboard_ops = { - CHIP_NAME("ASUS A8V-E SE Mainboard") + CHIP_NAME("ASUS K8V-X Mainboard") }; diff --git a/src/mainboard/asus/k8v-x/mptable.c b/src/mainboard/asus/k8v-x/mptable.c index 999dd6c..673dfbe 100644 --- a/src/mainboard/asus/k8v-x/mptable.c +++ b/src/mainboard/asus/k8v-x/mptable.c @@ -22,7 +22,7 @@ #include <arch/smp/mpspec.h> #include <arch/ioapic.h> #include "southbridge/via/vt8237r/vt8237r.h" -#include "southbridge/via/k8t890/k8t890.h" +#include "southbridge/via/k8t890/k8x8xx.h" static void *smp_write_config_table(void *v) { diff --git a/src/mainboard/asus/k8v-x/romstage.c b/src/mainboard/asus/k8v-x/romstage.c index 4e08859..014ce68 100644 --- a/src/mainboard/asus/k8v-x/romstage.c +++ b/src/mainboard/asus/k8v-x/romstage.c @@ -40,7 +40,7 @@ unsigned int get_sbdn(unsigned bus); #include "cpu/x86/lapic/boot_cpu.c" #include "northbridge/amd/amdk8/reset_test.c" #include "northbridge/amd/amdk8/early_ht.c" -#include "superio/winbond/w83627ehg/early_serial.c" +#include "superio/winbond/w83697hf/early_serial.c" #include "southbridge/via/vt8237r/early_smbus.c" #include "northbridge/amd/amdk8/debug.c" /* After vt8237r/early_smbus.c! */ #include "cpu/x86/mtrr/earlymtrr.c" @@ -48,9 +48,7 @@ unsigned int get_sbdn(unsigned bus); #include "northbridge/amd/amdk8/setup_resource_map.c" #include <spd.h> -#define SERIAL_DEV PNP_DEV(0x2e, W83627EHG_SP1) -#define GPIO_DEV PNP_DEV(0x2e, W83627EHG_GPIO_SUSLED_V) -#define ACPI_DEV PNP_DEV(0x2e, W83627EHG_ACPI) +#define SERIAL_DEV PNP_DEV(0x2e, W83697HF_SP1) static void memreset(int controllers, const struct mem_controller *ctrl) { } static void activate_spd_rom(const struct mem_controller *ctrl) { } @@ -105,52 +103,25 @@ static void sio_init(void) u8 reg; pnp_enter_ext_func_mode(SERIAL_DEV); - /* We have 24MHz input. */ reg = pnp_read_config(SERIAL_DEV, 0x24); - pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); - /* We have GPIO for KB/MS pin. */ - reg = pnp_read_config(SERIAL_DEV, 0x2a); - pnp_write_config(SERIAL_DEV, 0x2a, (reg | 1)); - /* We have all RESTOUT and even some reserved bits, too. */ - reg = pnp_read_config(SERIAL_DEV, 0x2c); - pnp_write_config(SERIAL_DEV, 0x2c, (reg | 0xf0)); - pnp_exit_ext_func_mode(SERIAL_DEV); - - pnp_enter_ext_func_mode(ACPI_DEV); - pnp_set_logical_device(ACPI_DEV); - /* - * Set the delay rising time from PWROK_LP to PWROK_ST to - * 300 - 600ms, and 0 to vice versa. - */ - reg = pnp_read_config(ACPI_DEV, 0xe6); - pnp_write_config(ACPI_DEV, 0xe6, (reg & 0xf0)); - /* 1 Use external suspend clock source 32.768KHz. Undocumented?? */ - reg = pnp_read_config(ACPI_DEV, 0xe4); - pnp_write_config(ACPI_DEV, 0xe4, (reg | 0x10)); - pnp_exit_ext_func_mode(ACPI_DEV); - - pnp_enter_ext_func_mode(GPIO_DEV); - pnp_set_logical_device(GPIO_DEV); - /* Set memory voltage to 2.75V, vcore offset + 100mV, 1.5V chipset voltage. */ - pnp_write_config(GPIO_DEV, 0x30, 0x09); /* Enable GPIO 2 & GPIO 5. */ - pnp_write_config(GPIO_DEV, 0xe2, 0x00); /* No inversion */ - pnp_write_config(GPIO_DEV, 0xe5, 0x00); /* No inversion */ - pnp_write_config(GPIO_DEV, 0xe3, 0x03); /* 0000 0011, 0=output 1=input */ - pnp_write_config(GPIO_DEV, 0xe0, 0xde); /* 1101 1110, 0=output 1=input */ - pnp_write_config(GPIO_DEV, 0xe1, 0x01); /* Set output val. */ - pnp_write_config(GPIO_DEV, 0xe4, 0xb4); /* Set output val (1011 0100). */ - pnp_exit_ext_func_mode(GPIO_DEV); + /* 4 Mbit flash */ + reg = (reg & ~0x30) | 0x20; + /* We have 24MHz input. */ + reg &= ~0x40; + /* enable MEMW#, so flash can be written */ + reg |= 0x08; + pnp_write_config(SERIAL_DEV, 0x24, reg); } void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { static const uint16_t spd_addr[] = { // Node 0 - DIMM0, DIMM2, 0, 0, - DIMM1, DIMM3, 0, 0, + DIMM0, DIMM1, DIMM2, 0, + 0, 0, 0, 0, // Node 1 - DIMM4, DIMM6, 0, 0, - DIMM5, DIMM7, 0, 0, + 0, 0, 0, 0, + 0, 0, 0, 0, }; unsigned bsp_apicid = 0; int needs_reset = 0; @@ -158,7 +129,7 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); sio_init(); - w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); + w83697hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); console_init(); enable_rom_decode(); @@ -173,7 +144,7 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) // FIXME why is this executed again? ---> sio_init(); - w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); + w83697hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); console_init(); enable_rom_decode(); // <--- FIXME why is this executed again? @@ -209,7 +180,8 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) soft_reset(); } - /* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */ + /* the HT settings needs to be OK, because link freq change may cause HT disconnect */ + vt8237_sb_enable_fid_vid(); enable_fid_change(); init_fidvid_bsp(bsp_apicid); @@ -220,6 +192,13 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); enable_smbus(); + + /* this seems to be some GPIO on the SMBus--in any case, setting these + * two bits reduces the pullup impedance of the bus lines and is required + * in order to be able to read SPD info */ + smbus_write_byte(0x48, 0x07, smbus_read_byte(0x48, 0x07) | 0x80); + smbus_write_byte(0x4a, 0x07, smbus_read_byte(0x4a, 0x07) | 0x10); + sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); post_cache_as_ram(); }

1 0

Patch set updated for coreboot: c31d869 fix superiotool for NCT6776F
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/391 -gerrit commit c31d8690fb0a5060fe59ee30b04739c000d6accb Author: Florian Zumbiehl <florz(a)florz.de> Date: Wed Nov 2 09:46:34 2011 +0100 fix superiotool for NCT6776F The current code exits config mode of the NCT6776F immediately after detection, so the register dump shows all 0xffs. This patch adds code to re-enter config mode for the register dump so that the register contents can be read. Change-Id: I4ad0c108b6411a665e31f55dea4b91ca77d1a5f7 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- util/superiotool/nuvoton.c | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/util/superiotool/nuvoton.c b/util/superiotool/nuvoton.c index 6a1a75c..ed2eabc 100644 --- a/util/superiotool/nuvoton.c +++ b/util/superiotool/nuvoton.c @@ -255,7 +255,9 @@ void probe_idregs_nuvoton(uint16_t port) printf("Found Nuvoton %s (id=0x%02x) at 0x%x\n", get_superio_name(reg_table, chip_id), chip_id, port); chip_found = 1; + enter_conf_mode_winbond_fintek_ite_8787(port); dump_superio("Nuvoton", reg_table, port, chip_id, LDN_SEL); + exit_conf_mode_winbond_fintek_ite_8787(port); return; }

1 0

Patch set updated for coreboot: e58524a implement hwmon fan divisor setting for w83697hf
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/384 -gerrit commit e58524afb555780feddc24fec1f2125340a4d666 Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:06 2011 +0100 implement hwmon fan divisor setting for w83697hf Change-Id: I887ac1142875ca1dc1a1eb8eebec402fbe7512c3 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/superio/winbond/w83697hf/chip.h | 3 +- src/superio/winbond/w83697hf/superio.c | 33 ++++++++++++++++++++++++++++++++ 2 files changed, 35 insertions(+), 1 deletions(-) diff --git a/src/superio/winbond/w83697hf/chip.h b/src/superio/winbond/w83697hf/chip.h index 1a1cbcc..2359b66 100644 --- a/src/superio/winbond/w83697hf/chip.h +++ b/src/superio/winbond/w83697hf/chip.h @@ -26,7 +26,8 @@ extern struct chip_operations superio_winbond_w83697hf_ops; struct superio_winbond_w83697hf_config { - + unsigned int hwmon_fan1_divisor; + unsigned int hwmon_fan2_divisor; }; #endif diff --git a/src/superio/winbond/w83697hf/superio.c b/src/superio/winbond/w83697hf/superio.c index d2cbcbd..a7f4f67 100644 --- a/src/superio/winbond/w83697hf/superio.c +++ b/src/superio/winbond/w83697hf/superio.c @@ -41,10 +41,43 @@ static void pnp_exit_ext_func_mode(device_t dev) outb(0xaa, dev->path.pnp.port); } +static void hwmon_set_fan_divisor(unsigned int base, int num, unsigned int divisor) { + unsigned char enc, buf; + + if (divisor) { + enc = log2(divisor); + if (1 << enc != divisor || enc > 7) + die("invalid fan divisor"); + outb(0x4e, base + 5); + outb(0x00, base + 6); + outb(0x47, base + 5); + outb((inb(base + 6) & ~(0x30 << (num * 2))) | ((enc & 3) << (4 + num * 2)), base + 6); + outb(0x5d, base + 5); + buf = inb(base + 6); + outb(0x5d, base + 5); // the above inb() auto-increments the address pointer ... + outb((buf & ~(0x20 << num)) | ((enc & 4) << (3 + num)), base + 6); + } +} + static void w83697hf_init(device_t dev) { + struct resource *res0; + struct superio_winbond_w83697hf_config *cfg; + if (!dev->enabled) return; + + cfg = dev->chip_info; + + switch (dev->path.pnp.device) { + case W83697HF_HWM: + if (cfg) { + res0 = find_resource(dev, PNP_IDX_IO0); + hwmon_set_fan_divisor(res0->base, 0, cfg->hwmon_fan1_divisor); + hwmon_set_fan_divisor(res0->base, 1, cfg->hwmon_fan2_divisor); + } + break; + } } static void w83697hf_pnp_set_resources(device_t dev)

1 0

Patch set updated for coreboot: f5023c4 implement usb2 termination and dpll delay setting for vt8237r
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/385 -gerrit commit f5023c413fceb8ddbe361c96e283de0927d278b0 Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:35 2011 +0100 implement usb2 termination and dpll delay setting for vt8237r Change-Id: I830c9a3daf5ac2e1ecd9a3e725a0b98f06509769 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/southbridge/via/vt8237r/chip.h | 13 +++++++++++++ src/southbridge/via/vt8237r/usb.c | 18 ++++++++++++++++++ 2 files changed, 31 insertions(+), 0 deletions(-) diff --git a/src/southbridge/via/vt8237r/chip.h b/src/southbridge/via/vt8237r/chip.h index f05d3c0..2e24fac 100644 --- a/src/southbridge/via/vt8237r/chip.h +++ b/src/southbridge/via/vt8237r/chip.h @@ -56,6 +56,19 @@ struct southbridge_via_vt8237r_config { /* 1 = 80-pin cable, 0 = 40-pin cable */ u8 ide0_80pin_cable; u8 ide1_80pin_cable; + + u8 usb2_termination_set; + u8 usb2_termination_a; + u8 usb2_termination_b; + u8 usb2_termination_c; + u8 usb2_termination_d; + u8 usb2_termination_e; + u8 usb2_termination_f; + u8 usb2_termination_g; + u8 usb2_termination_h; + + u8 usb2_dpll_set; + u8 usb2_dpll_delay; }; #endif /* SOUTHBRIDGE_VIA_VT8237R_CHIP_H */ diff --git a/src/southbridge/via/vt8237r/usb.c b/src/southbridge/via/vt8237r/usb.c index 6e8d9e5..35530b4 100644 --- a/src/southbridge/via/vt8237r/usb.c +++ b/src/southbridge/via/vt8237r/usb.c @@ -22,6 +22,7 @@ #include <device/device.h> #include <device/pci.h> #include <device/pci_ids.h> +#include "chip.h" #include "vt8237r.h" #if CONFIG_EPIA_VT8237R_INIT @@ -94,6 +95,7 @@ static void vt8237_usb_i_read_resources(struct device *dev) static void usb_ii_init(struct device *dev) { + struct southbridge_via_vt8237r_config *cfg; #if CONFIG_EPIA_VT8237R_INIT u8 reg8; @@ -112,6 +114,22 @@ static void usb_ii_init(struct device *dev) pci_write_config16(dev, 0x06, 0x7A10); #endif + cfg = dev->chip_info; + + if (cfg) { + if (cfg->usb2_termination_set) { + /* High Speed Port Pad Termination Resistor Fine Tune */ + pci_write_config8(dev, 0x5a, cfg->usb2_termination_c | (cfg->usb2_termination_d << 4)); + pci_write_config8(dev, 0x5b, cfg->usb2_termination_a | (cfg->usb2_termination_b << 4)); + pci_write_config8(dev, 0x5d, cfg->usb2_termination_e | (cfg->usb2_termination_f << 4)); + pci_write_config8(dev, 0x5e, cfg->usb2_termination_g | (cfg->usb2_termination_h << 4)); + } + + if (cfg->usb2_dpll_set) { + /* Delay DPLL Input Data Control */ + pci_write_config8(dev, 0x5c, (pci_read_config8(dev, 0x5c) & ~0x70) | (cfg->usb2_dpll_delay << 4)); + } + } } static void vt8237_usb_ii_read_resources(struct device *dev)

1 0

Patch set updated for coreboot: 13fc22c make INT[EFGH]# of vt8237 configurable via devicetree
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/386 -gerrit commit 13fc22c262c608540989c8af241440da2f4b638a Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:36 2011 +0100 make INT[EFGH]# of vt8237 configurable via devicetree Change-Id: I70202d81ddd1b0a00eddca4acabc621e5783e805 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/southbridge/via/vt8237r/chip.h | 2 ++ src/southbridge/via/vt8237r/lpc.c | 21 ++++++++++++++++++--- 2 files changed, 20 insertions(+), 3 deletions(-) diff --git a/src/southbridge/via/vt8237r/chip.h b/src/southbridge/via/vt8237r/chip.h index 2e24fac..be5e7fc 100644 --- a/src/southbridge/via/vt8237r/chip.h +++ b/src/southbridge/via/vt8237r/chip.h @@ -69,6 +69,8 @@ struct southbridge_via_vt8237r_config { u8 usb2_dpll_set; u8 usb2_dpll_delay; + + u8 no_int_efgh; }; #endif /* SOUTHBRIDGE_VIA_VT8237R_CHIP_H */ diff --git a/src/southbridge/via/vt8237r/lpc.c b/src/southbridge/via/vt8237r/lpc.c index 0e757fe..d4f7820 100644 --- a/src/southbridge/via/vt8237r/lpc.c +++ b/src/southbridge/via/vt8237r/lpc.c @@ -67,6 +67,8 @@ static void pci_routing_fixup(struct device *dev) { #if CONFIG_EPIA_VT8237R_INIT device_t pdev; +#else + struct southbridge_via_vt8237r_config *cfg; #endif /* PCI PNP Interrupt Routing INTE/F - disable */ @@ -124,8 +126,14 @@ static void pci_routing_fixup(struct device *dev) pci_write_config8(pdev, PCI_INTERRUPT_LINE, 0xFF); #else - /* Route INTE-INTH through registers above, no map to INTA-INTD. */ - pci_write_config8(dev, 0x46, 0x10); + cfg = dev->chip_info; + + if (cfg && cfg->no_int_efgh) { + pci_write_config8(dev, 0x46, 0x00); + } else { + /* Route INTE-INTH through registers above, no map to INTA-INTD. */ + pci_write_config8(dev, 0x46, 0x10); + } /* PCI Interrupt Polarity */ pci_write_config8(dev, 0x54, 0x00); @@ -421,6 +429,9 @@ static void vt8237s_init(struct device *dev) static void vt8237_common_init(struct device *dev) { u8 enables, byte; + struct southbridge_via_vt8237r_config *cfg; + + cfg = dev->chip_info; /* Enable addr/data stepping. */ byte = pci_read_config8(dev, PCI_COMMAND); @@ -506,7 +517,11 @@ static void vt8237_common_init(struct device *dev) * | bit 1=1 works for Aaron at VIA, bit 1=0 works for jakllsch * 0 | Dynamic Clock Gating Main Switch (1=Enable) */ - pci_write_config8(dev, 0x5b, 0xb); + if (cfg && cfg->no_int_efgh) { + pci_write_config8(dev, 0x5b, 0x9); + } else { + pci_write_config8(dev, 0x5b, 0xb); + } #if CONFIG_VT8237R_ON_AFTER_POWER_LOSS /* make it so the board unconditionally powers on after loss of power */

1 0

Patch set updated for coreboot: 31de04d make GPIOs and misc configurable via devicetree
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/387 -gerrit commit 31de04d87ffc93f1bc28ef93b39b65110e1766be Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:19:37 2011 +0100 make GPIOs and misc configurable via devicetree Change-Id: I9f70da76b5ea451f28a1ad9252c5d879fc4fe315 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/southbridge/via/vt8237r/chip.h | 5 +++++ src/southbridge/via/vt8237r/lpc.c | 30 +++++++++++++++++++++++++++--- 2 files changed, 32 insertions(+), 3 deletions(-) diff --git a/src/southbridge/via/vt8237r/chip.h b/src/southbridge/via/vt8237r/chip.h index be5e7fc..64b8e8e 100644 --- a/src/southbridge/via/vt8237r/chip.h +++ b/src/southbridge/via/vt8237r/chip.h @@ -71,6 +71,11 @@ struct southbridge_via_vt8237r_config { u8 usb2_dpll_delay; u8 no_int_efgh; + u8 enable_gpo3; + u8 disable_gpo26_gpo27; + u8 enable_aol_2_smb_slave; + u8 enable_gpo5; + u8 gpio15_12_dir_output; }; #endif /* SOUTHBRIDGE_VIA_VT8237R_CHIP_H */ diff --git a/src/southbridge/via/vt8237r/lpc.c b/src/southbridge/via/vt8237r/lpc.c index d4f7820..7d7326c 100644 --- a/src/southbridge/via/vt8237r/lpc.c +++ b/src/southbridge/via/vt8237r/lpc.c @@ -159,6 +159,10 @@ static void pci_routing_fixup(struct device *dev) static void setup_pm(device_t dev) { u16 tmp; + struct southbridge_via_vt8237r_config *cfg; + + cfg = dev->chip_info; + /* Debounce LID and PWRBTN# Inputs for 16ms. */ pci_write_config8(dev, 0x80, 0x20); @@ -187,7 +191,10 @@ static void setup_pm(device_t dev) * 5 = Internal PLL reset from susp disabled * 2 = GPO2 is SUSA# */ - pci_write_config8(dev, 0x94, 0xa0); + tmp = 0xa0; + if (cfg && cfg->enable_gpo3) + tmp |= 0x10; + pci_write_config8(dev, 0x94, tmp); /* * 7 = stp to sust delay 1msec @@ -203,7 +210,14 @@ static void setup_pm(device_t dev) #if CONFIG_EPIA_VT8237R_INIT pci_write_config8(dev, 0x95, 0xc2); #else - pci_write_config8(dev, 0x95, 0xcc); + tmp = 0xcc; + if (cfg) { + if (cfg->disable_gpo26_gpo27) + tmp &= ~0x08; + if (cfg->enable_aol_2_smb_slave) + tmp &= ~0x04; + } + pci_write_config8(dev, 0x95, tmp); #endif /* Disable GP3 timer. */ @@ -255,6 +269,9 @@ static void setup_pm(device_t dev) static void vt8237r_init(struct device *dev) { u8 enables; + struct southbridge_via_vt8237r_config *cfg; + + cfg = dev->chip_info; #if CONFIG_EPIA_VT8237R_INIT printk(BIOS_SPEW, "Entering vt8237r_init, for EPIA.\n"); @@ -290,8 +307,15 @@ static void vt8237r_init(struct device *dev) */ pci_write_config8(dev, 0xe5, 0x09); + enables = 0x4; + if (cfg) { + if (cfg->enable_gpo5) + enables |= 0x01; + if (cfg->gpio15_12_dir_output) + enables |= 0x10; + } /* REQ5 as PCI request input - should be together with INTE-INTH. */ - pci_write_config8(dev, 0xe4, 0x4); + pci_write_config8(dev, 0xe4, enables); #endif /* Set bit 3 of 0x4f (use INIT# as CPU reset). */

1 0

Patch set updated for coreboot: 24e70cf factor out common config for k8x8xx's dram_enable() and vt8237r_cfg()
by Florian Zumbiehl 02 Nov '11

02 Nov '11

Florian Zumbiehl just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/378 -gerrit commit 24e70cf2a2594bda06b4e6de943a75a27d0256f8 Author: Florian Zumbiehl <florz(a)florz.de> Date: Tue Nov 1 20:18:30 2011 +0100 factor out common config for k8x8xx's dram_enable() and vt8237r_cfg() Instead of writing to config registers in k8x8xx's dram_enable() and reading those back in vt8237r_cfg(), factor out generation of the values and reuse that in both places. Change-Id: I87a37398efe84b33e6678df74cd40b5abfe4f879 Signed-off-by: Florian Zumbiehl <florz(a)florz.de> --- src/southbridge/via/k8t890/ctrl.c | 49 ++++++---------------------------- src/southbridge/via/k8t890/dram.c | 18 ++++++------ src/southbridge/via/k8t890/k8x8xx.h | 25 ++++++++++++++++++ 3 files changed, 43 insertions(+), 49 deletions(-) diff --git a/src/southbridge/via/k8t890/ctrl.c b/src/southbridge/via/k8t890/ctrl.c index 42676b1..7363510 100644 --- a/src/southbridge/via/k8t890/ctrl.c +++ b/src/southbridge/via/k8t890/ctrl.c @@ -31,31 +31,8 @@ static void vt8237r_cfg(struct device *dev, struct device *devsb) { - u8 regm, regm3; - - device_t devfun3; - - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8T800_DRAM, 0); - - if (!devfun3) - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8M800_DRAM, 0); - - if (!devfun3) - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8T890CE_3, 0); - - if (!devfun3) - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8T890CF_3, 0); - - if (!devfun3) - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8M890CE_3, 0); - - if(!devfun3) - die("\n vt8237r_cfg: Unable to find K8x8xx bridge via PCI scan. Stopping.\n"); + u8 regm3; + struct k8x8xx_vt8237_mirrored_regs mregs; pci_write_config8(dev, 0x70, 0xc2); @@ -71,21 +48,14 @@ static void vt8237r_cfg(struct device *dev, struct device *devsb) pci_write_config8(dev, 0x7c, 0x7f); pci_write_config8(dev, 0x7f, 0x02); - /* WARNING: Need to copy some registers from NB (D0F3) to SB (D0F7). */ - - regm = pci_read_config8(devfun3, 0x88); /* Shadow mem CTRL */ - pci_write_config8(dev, 0x57, regm); - - regm = pci_read_config8(devfun3, 0x80); /* Shadow page C */ - pci_write_config8(dev, 0x61, regm); - - regm = pci_read_config8(devfun3, 0x81); /* Shadow page D */ - pci_write_config8(dev, 0x62, regm); + k8x8xx_vt8237_mirrored_regs_fill(&mregs); - regm = pci_read_config8(devfun3, 0x86); /* SMM and APIC decoding */ - pci_write_config8(dev, 0xe6, regm); + pci_write_config8(dev, 0x57, mregs.shadow_mem_ctrl); /* Shadow mem CTRL */ + pci_write_config8(dev, 0x61, mregs.rom_shadow_ctrl_pg_c); /* Shadow page C */ + pci_write_config8(dev, 0x62, mregs.rom_shadow_ctrl_pg_d); /* Shadow page D */ + pci_write_config8(dev, 0xe6, mregs.smm_apic_decoding); /* SMM and APIC decoding */ - regm3 = pci_read_config8(devfun3, 0x82);/* Shadow page E */ + regm3 = mregs.rom_shadow_ctrl_pg_e_memhole_smi_decoding; /* Shadow page E */ /* * All access bits for 0xE0000-0xEFFFF encode as just 2 bits! @@ -98,8 +68,7 @@ static void vt8237r_cfg(struct device *dev, struct device *devsb) regm3 = 0x0; /* Shadow page F + memhole copy */ - regm = pci_read_config8(devfun3, 0x83); - pci_write_config8(dev, 0x63, regm3 | (regm & 0x3F)); + pci_write_config8(dev, 0x63, regm3 | (mregs.rom_shadow_ctrl_pg_f_memhole & 0x3F)); } diff --git a/src/southbridge/via/k8t890/dram.c b/src/southbridge/via/k8t890/dram.c index 9b43a5e..294e387 100644 --- a/src/southbridge/via/k8t890/dram.c +++ b/src/southbridge/via/k8t890/dram.c @@ -30,14 +30,15 @@ static void dram_enable(struct device *dev) { - msr_t msr; u16 reg; + struct k8x8xx_vt8237_mirrored_regs mregs; + k8x8xx_vt8237_mirrored_regs_fill(&mregs); /* * Enable Lowest Interrupt arbitration for APIC, enable NB APIC * decoding, MSI support, no SMRAM, compatible SMM. */ - pci_write_config8(dev, 0x86, 0x19); + pci_write_config8(dev, 0x86, mregs.smm_apic_decoding); /* * We want to use the 0xC0000-0xEFFFF as RAM mark area as RW, even if @@ -48,23 +49,22 @@ static void dram_enable(struct device *dev) /* For CC000-CFFFF, bits 7:6 (10 = REn, 01 = WEn) bits 1:0 for * C0000-C3FFF etc. */ - pci_write_config8(dev, 0x80, 0xff); + pci_write_config8(dev, 0x80, mregs.rom_shadow_ctrl_pg_c); /* For page D0000-DFFFF */ - pci_write_config8(dev, 0x81, 0xff); + pci_write_config8(dev, 0x81, mregs.rom_shadow_ctrl_pg_d); /* For page E0000-EFFFF */ - pci_write_config8(dev, 0x82, 0xff); - pci_write_config8(dev, 0x83, 0x30); + pci_write_config8(dev, 0x82, mregs.rom_shadow_ctrl_pg_e_memhole_smi_decoding); + pci_write_config8(dev, 0x83, mregs.rom_shadow_ctrl_pg_f_memhole); - msr = rdmsr(TOP_MEM); reg = pci_read_config16(dev, 0x84); reg &= 0xf; - pci_write_config16(dev, 0x84, (msr.lo >> 16) | reg); + pci_write_config16(dev, 0x84, mregs.low_top_address | reg); reg = pci_read_config16(dev, 0x88); reg &= 0xf800; /* The Address Next to the Last Valid DRAM Address */ - pci_write_config16(dev, 0x88, (msr.lo >> 24) | reg); + pci_write_config16(dev, 0x88, reg | mregs.shadow_mem_ctrl); print_debug(" VIA_X_3 device dump:\n"); dump_south(dev); diff --git a/src/southbridge/via/k8t890/k8x8xx.h b/src/southbridge/via/k8t890/k8x8xx.h index a0fb57a..425aaeb 100644 --- a/src/southbridge/via/k8t890/k8x8xx.h +++ b/src/southbridge/via/k8t890/k8x8xx.h @@ -21,6 +21,31 @@ #ifndef SOUTHBRIDGE_VIA_K8T890_K8X8XX_H #define SOUTHBRIDGE_VIA_K8T890_K8X8XX_H +#include <cpu/x86/msr.h> +#include <cpu/amd/mtrr.h> #include "k8t890.h" +struct k8x8xx_vt8237_mirrored_regs { + u16 low_top_address; + u8 rom_shadow_ctrl_pg_c, + rom_shadow_ctrl_pg_d, + rom_shadow_ctrl_pg_e_memhole_smi_decoding, + rom_shadow_ctrl_pg_f_memhole, + smm_apic_decoding, + shadow_mem_ctrl; +}; + +static inline void k8x8xx_vt8237_mirrored_regs_fill(struct k8x8xx_vt8237_mirrored_regs *regs){ + msr_t msr; + + regs->rom_shadow_ctrl_pg_c = 0xff; + regs->rom_shadow_ctrl_pg_d = 0xff; + regs->rom_shadow_ctrl_pg_e_memhole_smi_decoding = 0xff; + regs->rom_shadow_ctrl_pg_f_memhole = 0x30; + regs->smm_apic_decoding = 0x19; + msr = rdmsr(TOP_MEM); + regs->shadow_mem_ctrl = msr.lo >> 24; + regs->low_top_address = msr.lo >> 16; +} + #endif /* SOUTHBRIDGE_VIA_K8T890_K8X8XX_H */

1 0

← Newer
1
...
31
32
33
34
35
36
37
...
44
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot November 2011