coreboot September 2008

coreboot@coreboot.org

59 participants
415 discussions

v2: Emulator goes astray in pxe-rom images
by Mats Erik Andersson 12 Sep '08

12 Sep '08

Hello all, I have observed a phenomenon too many times now to ignore it. When I leave an eepro100 network adapter in the pci slot, the emulator on Coreboot all to often comes to a halt, but its removal and an immediate cold boot lets Coreboot progress all the way into Filo. Of course the emulator admits to having found a non-VGA rom image, but then grounds to a halt, or in the best of cases spits out an execution exception, or on illegal x86 op-code. Can someone offer me an explanation, or point me to a procedure that makes the emulator less picky. Best regards, Mats E Andersson

3 2

jetway IDE enable strangeness
by Alex Mauer 12 Sep '08

12 Sep '08

Previously when I was testing the jetway target, I found that the IDE devices were always enabled, as the mainboard's Config.lb seems to suggest would be the case. Today, after running an 'svn up' and reverting the src/southbridge/via/vt8237r to before the breakage in rev 3567, I found that the IDE devices aren't ever enabled, no matter what I set for the values of ide0_enable and ide1_enable in the mainboard's Config.lb. And of course, the board won't boot. I looked in the built target's image/static.c and found the struct southbridge_via_vt8237r_config with ide0_enable and ide1_enable both set to 1 as they should be. But back in src/southbridge/via/vt8237r/vt8237r_ide.c (around line 41), sb->ide0_enable and sb->ide1_enable are both 0. Forcing them to 1 there causes the devices to be enabled, and then the system will boot. But the question is, what's going on there? Why are these values set to 0? Is ide_init accessing chip_info for the wrong device? Does anyone have any ideas? -Alex Mauer "hawke"

3 3

Buildrom users - important, please read!
by Jordan Crouse 12 Sep '08

12 Sep '08

The new FILO has been committed to buildrom. Because the SVN tree has changed, the svn fetch script will get confused. Before building FILO again, please remove the FILO svn tree from your sources/ directory: rm -rf sources/filo/ And run 'make distclean' before rebuilding. Thank you, Jordan -- Jordan Crouse Systems Software Development Engineer Advanced Micro Devices, Inc.

1 0

Convert Assembly JMP to C
by Joseph Smith 12 Sep '08

12 Sep '08

Hello, How do I convert an Assembly JMP instruction to C. What I would like to do is execute an executable assembly blob located in memory. From the docs I have read, for assembly you just need to issues a JMP to the memory location to execute it. How to do the same in C, that is the question... P.S. This question is leading up to something great :-) -- Thanks, Joseph Smith Set-Top-Linux www.settoplinux.org

9 42

r226 - in buildrom-devel: config/payloads config/platforms packages/filo packages/filo/conf
by svn＠coreboot.org 12 Sep '08

12 Sep '08

Author: jcrouse Date: 2008-09-12 19:18:00 +0200 (Fri, 12 Sep 2008) New Revision: 226 Removed: buildrom-devel/packages/filo/conf/alix1c-Config buildrom-devel/packages/filo/conf/alix2c3-Config buildrom-devel/packages/filo/conf/asus_a8v-e_se-Config buildrom-devel/packages/filo/conf/db800-Config buildrom-devel/packages/filo/conf/ga-2761gxdk-Config buildrom-devel/packages/filo/conf/m57sli-Config buildrom-devel/packages/filo/conf/msm800sev-Config buildrom-devel/packages/filo/conf/norwich-Config buildrom-devel/packages/filo/conf/qemu-Config buildrom-devel/packages/filo/conf/serengeti_cheetah-Config buildrom-devel/packages/filo/conf/supermicro-h8dmr-Config buildrom-devel/packages/filo/conf/tyan-generic-Config buildrom-devel/packages/filo/conf/tyan-s2881-Config buildrom-devel/packages/filo/conf/tyan-s2882-Config buildrom-devel/packages/filo/conf/tyan-s2891-Config Modified: buildrom-devel/config/payloads/payloads.conf buildrom-devel/config/platforms/alix1c.conf buildrom-devel/config/platforms/asus_a8v-e_se.conf buildrom-devel/config/platforms/db800.conf buildrom-devel/config/platforms/dbe61.conf buildrom-devel/config/platforms/ga-2761gxdk.conf buildrom-devel/config/platforms/m57sli.conf buildrom-devel/config/platforms/msm800sev.conf buildrom-devel/config/platforms/norwich.conf buildrom-devel/config/platforms/qemu.conf buildrom-devel/config/platforms/serengeti_cheetah.conf buildrom-devel/config/platforms/supermicro-h8dmr.conf buildrom-devel/config/platforms/tyan-s2881.conf buildrom-devel/config/platforms/tyan-s2882.conf buildrom-devel/config/platforms/tyan-s2891.conf buildrom-devel/config/platforms/tyan-s2892.conf buildrom-devel/config/platforms/tyan-s2895.conf buildrom-devel/packages/filo/filo.mk Log: [PATCH] libpayload: Update FILO to the trunk Update FILO to build from the trunk - we will use the default configuration for all platforms (for now), so remove the previous configurations and infrastructure. Signed-off-by: Jordan Crouse <jordan.crouse(a)amd.com> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: buildrom-devel/config/payloads/payloads.conf =================================================================== --- buildrom-devel/config/payloads/payloads.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/payloads/payloads.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -41,6 +41,7 @@ PCONF-$(CONFIG_PAYLOAD_OFW) = ofw.conf PCONF-$(CONFIG_PAYLOAD_OPENBIOS) = openbios.conf PCONF-$(CONFIG_PAYLOAD_TINT) = libpayload-dep.conf +PCONF-$(CONFIG_PAYLOAD_FILO) = libpayload-dep.conf include $(CONFIG_DIR)/payloads/$(PCONF-y) Modified: buildrom-devel/config/platforms/alix1c.conf =================================================================== --- buildrom-devel/config/platforms/alix1c.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/alix1c.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -22,8 +22,3 @@ CBV2_TAG=3335 CBV3_TAG=682 - -# FILO configuration - -FILO_CONFIG=alix1c-Config - Modified: buildrom-devel/config/platforms/asus_a8v-e_se.conf =================================================================== --- buildrom-devel/config/platforms/asus_a8v-e_se.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/asus_a8v-e_se.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -33,8 +33,3 @@ COREBOOT_BOARD=a8v-e_se CBV2_TDIR=asus_a8v-e_se CBV2_TAG=3241 - -# FILO configuration - -FILO_CONFIG=asus_a8v-e_se-Config - Modified: buildrom-devel/config/platforms/db800.conf =================================================================== --- buildrom-devel/config/platforms/db800.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/db800.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -22,9 +22,3 @@ COREBOOT_BOARD=db800 CBV2_TDIR=db800 CBV2_TAG=3335 - -# FILO configuration -# Use a new FILO config for the DB800 to autoload an image - -FILO_CONFIG=db800-Config - Modified: buildrom-devel/config/platforms/dbe61.conf =================================================================== --- buildrom-devel/config/platforms/dbe61.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/dbe61.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -22,8 +22,3 @@ COREBOOT_BOARD=dbe61 CBV2_TDIR=dbe61 CBV2_TAG=3335 - -# FILO configuration - -FILO_CONFIG=norwich-Config - Modified: buildrom-devel/config/platforms/ga-2761gxdk.conf =================================================================== --- buildrom-devel/config/platforms/ga-2761gxdk.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/ga-2761gxdk.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -26,8 +26,3 @@ COREBOOT_BOARD=ga_2761gxdk CBV2_TDIR=ga_2761gxdk CBV2_TAG=3335 - -# FILO configuration - -FILO_CONFIG=ga-2761gxdk-Config - Modified: buildrom-devel/config/platforms/m57sli.conf =================================================================== --- buildrom-devel/config/platforms/m57sli.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/m57sli.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -31,8 +31,3 @@ COREBOOT_BOARD=m57sli CBV2_TDIR=m57sli CBV2_TAG=3381 - -# FILO configuration - -FILO_CONFIG=m57sli-Config - Modified: buildrom-devel/config/platforms/msm800sev.conf =================================================================== --- buildrom-devel/config/platforms/msm800sev.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/msm800sev.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -21,8 +21,3 @@ COREBOOT_BOARD=msm800sev CBV2_TDIR=msm800sev CBV2_TAG=3335 - -# FILO configuration - -FILO_CONFIG=msm800sev-Config - Modified: buildrom-devel/config/platforms/norwich.conf =================================================================== --- buildrom-devel/config/platforms/norwich.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/norwich.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -21,8 +21,3 @@ COREBOOT_BOARD=norwich CBV2_TDIR=norwich CBV2_TAG=3294 - -# FILO configuration - -FILO_CONFIG=norwich-Config - Modified: buildrom-devel/config/platforms/qemu.conf =================================================================== --- buildrom-devel/config/platforms/qemu.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/qemu.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -23,8 +23,3 @@ COREBOOT_VENDOR=emulation COREBOOT_BOARD=qemu-x86 - -# FILO configuration - -FILO_CONFIG=qemu-Config - Modified: buildrom-devel/config/platforms/serengeti_cheetah.conf =================================================================== --- buildrom-devel/config/platforms/serengeti_cheetah.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/serengeti_cheetah.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -46,8 +46,3 @@ CBV2_TDIR=serengeti_cheetah CBV2_TAG=3343 endif - -# FILO configuration - -FILO_CONFIG=serengeti_cheetah-Config - Modified: buildrom-devel/config/platforms/supermicro-h8dmr.conf =================================================================== --- buildrom-devel/config/platforms/supermicro-h8dmr.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/supermicro-h8dmr.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -31,8 +31,3 @@ COREBOOT_BOARD=h8dmr CBV2_TDIR=h8dmr CBV2_TAG=3278 - -# FILO configuration - -FILO_CONFIG=supermicro-h8dmr-Config - Modified: buildrom-devel/config/platforms/tyan-s2881.conf =================================================================== --- buildrom-devel/config/platforms/tyan-s2881.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/tyan-s2881.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -31,8 +31,3 @@ COREBOOT_BOARD=s2881 CBV2_TDIR=s2881 CBV2_TAG=3131 - -# FILO configuration - -FILO_CONFIG=tyan-s2881-Config - Modified: buildrom-devel/config/platforms/tyan-s2882.conf =================================================================== --- buildrom-devel/config/platforms/tyan-s2882.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/tyan-s2882.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -31,8 +31,3 @@ COREBOOT_BOARD=s2882 CBV2_TDIR=s2882 CBV2_TAG=3114 - -# FILO configuration - -FILO_CONFIG=tyan-s2882-Config - Modified: buildrom-devel/config/platforms/tyan-s2891.conf =================================================================== --- buildrom-devel/config/platforms/tyan-s2891.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/tyan-s2891.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -31,8 +31,3 @@ COREBOOT_BOARD=s2891 CBV2_TDIR=s2891 CBV2_TAG=3259 - -# FILO configuration - -FILO_CONFIG=tyan-s2891-Config - Modified: buildrom-devel/config/platforms/tyan-s2892.conf =================================================================== --- buildrom-devel/config/platforms/tyan-s2892.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/tyan-s2892.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -29,8 +29,3 @@ COREBOOT_BOARD=s2892 CBV2_TDIR=s2892 CBV2_TAG=3259 - -# FILO configuration - -FILO_CONFIG=tyan-generic-Config - Modified: buildrom-devel/config/platforms/tyan-s2895.conf =================================================================== --- buildrom-devel/config/platforms/tyan-s2895.conf 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/config/platforms/tyan-s2895.conf 2008-09-12 17:18:00 UTC (rev 226) @@ -29,8 +29,3 @@ COREBOOT_BOARD=s2895 CBV2_TDIR=s2895 CBV2_TAG=3259 - -# FILO configuration - -FILO_CONFIG=tyan-generic-Config - Deleted: buildrom-devel/packages/filo/conf/alix1c-Config =================================================================== --- buildrom-devel/packages/filo/conf/alix1c-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/alix1c-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/alix2c3-Config =================================================================== --- buildrom-devel/packages/filo/conf/alix2c3-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/alix2c3-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,16 +0,0 @@ -USE_GRUB = 1 -MENULST_FILE = "hda1:/boot/grub/menu.lst" -IDE_DISK = 1 -IDE_DISK_POLL_DELAY = 1 -USB_DISK = 1 -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -ELTORITO = 1 -SUPPORT_PCI = 1 -PCI_BRUTE_SCAN = 1 -LINUX_LOADER = 1 Deleted: buildrom-devel/packages/filo/conf/asus_a8v-e_se-Config =================================================================== --- buildrom-devel/packages/filo/conf/asus_a8v-e_se-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/asus_a8v-e_se-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,17 +0,0 @@ -USE_GRUB = 1 -MENULST_FILE = "hda2:/boot/grub/menu.lst" -IDE_DISK = 1 -IDE_DISK_POLL_DELAY = 1 -SLOW_SATA = 1 -USB_DISK = 1 -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -ELTORITO = 1 -SUPPORT_PCI = 1 -PCI_BRUTE_SCAN = 1 -LINUX_LOADER = 1 Deleted: buildrom-devel/packages/filo/conf/db800-Config =================================================================== --- buildrom-devel/packages/filo/conf/db800-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/db800-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,101 +0,0 @@ -# !!! NOTE !!! -# Do NOT add spaces or comments at the end of option lines. -# It confuses some versions of make. - -# Use grub instead of autoboot? -USE_GRUB = 1 - -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/menu.lst" -# Via Epia-MII CF boot: -#MENULST_FILE = "hde1:/boot/filo/menu.lst" - -# time before default menu.lst is chosen. Set to 0 to ignore -MENULST_TIMEOUT = 10 - -# Image filename for automatic boot and optional command line parameter -AUTOBOOT_FILE = "hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200" -#AUTOBOOT_FILE = "mem@0xfff80000" -#AUTOBOOT_FILE = "hde1@0" -#AUTOBOOT_FILE = "uda1:/vmlinuz.elf" - -# Time in second before booting AUTOBOOT_FILE -AUTOBOOT_DELAY = 2 - -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 - -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -# NOTE: Slows down access significantly, so disable -# whenever possible. -#IDE_DISK_POLL_DELAY = 1 - -# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E -# This device is referred to as hde. -#PCMCIA_CF = 1 - -# Driver for USB Storage -# USB_DISK = 1 - -# VGA text console -# VGA_CONSOLE = 1 -# PC_KEYBOARD = 1 - -# Serial console -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -# if SERIAL_SPEED is commented out, the speed will not be changed. -#SERIAL_SPEED = 115200 - -# Filesystems -FSYS_EXT2FS = 1 -FSYS_FAT = 1 -#FSYS_JFS = 1 -#FSYS_MINIX = 1 -FSYS_REISERFS = 1 -#FSYS_XFS = 1 -FSYS_ISO9660 = 1 - -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 - -# PCI support -SUPPORT_PCI = 1 - -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 - -# Sound support (needs SUPPORT_PCI) -#SUPPORT_SOUND = 1 - -# Sound drivers -#VIA_SOUND = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - -# i386 options - -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Boot FILO from Multiboot loader (eg. GRUB) -#MULTIBOOT_IMAGE = 1 - Deleted: buildrom-devel/packages/filo/conf/ga-2761gxdk-Config =================================================================== --- buildrom-devel/packages/filo/conf/ga-2761gxdk-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/ga-2761gxdk-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hde1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/m57sli-Config =================================================================== --- buildrom-devel/packages/filo/conf/m57sli-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/m57sli-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,52 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hde1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Wait 5 seconds to allow the sata disks to spin up -SLOW_SATA = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/msm800sev-Config =================================================================== --- buildrom-devel/packages/filo/conf/msm800sev-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/msm800sev-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,101 +0,0 @@ -# !!! NOTE !!! -# Do NOT add spaces or comments at the end of option lines. -# It confuses some versions of make. - -# Use grub instead of autoboot? -USE_GRUB = 1 - -# Grub menu.lst path -MENULST_FILE = "hda2:/boot/menu.lst" -# Via Epia-MII CF boot: -#MENULST_FILE = "hde1:/boot/filo/menu.lst" - -# time before default menu.lst is chosen. Set to 0 to ignore -MENULST_TIMEOUT = 0 - -# Image filename for automatic boot and optional command line parameter -AUTOBOOT_FILE = "hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200" -#AUTOBOOT_FILE = "mem@0xfff80000" -#AUTOBOOT_FILE = "hde1@0" -#AUTOBOOT_FILE = "uda1:/vmlinuz.elf" - -# Time in second before booting AUTOBOOT_FILE -AUTOBOOT_DELAY = 2 - -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 - -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -# NOTE: Slows down access significantly, so disable -# whenever possible. -#IDE_DISK_POLL_DELAY = 1 - -# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E -# This device is referred to as hde. -#PCMCIA_CF = 1 - -# Driver for USB Storage -# USB_DISK = 1 - -# VGA text console -# VGA_CONSOLE = 1 -# PC_KEYBOARD = 1 - -# Serial console -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -# if SERIAL_SPEED is commented out, the speed will not be changed. -#SERIAL_SPEED = 115200 - -# Filesystems -FSYS_EXT2FS = 1 -FSYS_FAT = 1 -#FSYS_JFS = 1 -#FSYS_MINIX = 1 -FSYS_REISERFS = 1 -#FSYS_XFS = 1 -FSYS_ISO9660 = 1 - -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 - -# PCI support -SUPPORT_PCI = 1 - -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 - -# Sound support (needs SUPPORT_PCI) -#SUPPORT_SOUND = 1 - -# Sound drivers -#VIA_SOUND = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - -# i386 options - -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Boot FILO from Multiboot loader (eg. GRUB) -#MULTIBOOT_IMAGE = 1 - Deleted: buildrom-devel/packages/filo/conf/norwich-Config =================================================================== --- buildrom-devel/packages/filo/conf/norwich-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/norwich-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,101 +0,0 @@ -# !!! NOTE !!! -# Do NOT add spaces or comments at the end of option lines. -# It confuses some versions of make. - -# Use grub instead of autoboot? -USE_GRUB = 1 - -# Grub menu.lst path -MENULST_FILE = "hda2:/boot/menu.lst" -# Via Epia-MII CF boot: -#MENULST_FILE = "hde1:/boot/filo/menu.lst" - -# time before default menu.lst is chosen. Set to 0 to ignore -MENULST_TIMEOUT = 0 - -# Image filename for automatic boot and optional command line parameter -AUTOBOOT_FILE = "hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200" -#AUTOBOOT_FILE = "mem@0xfff80000" -#AUTOBOOT_FILE = "hde1@0" -#AUTOBOOT_FILE = "uda1:/vmlinuz.elf" - -# Time in second before booting AUTOBOOT_FILE -AUTOBOOT_DELAY = 2 - -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 - -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -# NOTE: Slows down access significantly, so disable -# whenever possible. -#IDE_DISK_POLL_DELAY = 1 - -# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E -# This device is referred to as hde. -#PCMCIA_CF = 1 - -# Driver for USB Storage -# USB_DISK = 1 - -# VGA text console -# VGA_CONSOLE = 1 -# PC_KEYBOARD = 1 - -# Serial console -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -# if SERIAL_SPEED is commented out, the speed will not be changed. -#SERIAL_SPEED = 115200 - -# Filesystems -FSYS_EXT2FS = 1 -FSYS_FAT = 1 -#FSYS_JFS = 1 -#FSYS_MINIX = 1 -FSYS_REISERFS = 1 -#FSYS_XFS = 1 -FSYS_ISO9660 = 1 - -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 - -# PCI support -SUPPORT_PCI = 1 - -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 - -# Sound support (needs SUPPORT_PCI) -#SUPPORT_SOUND = 1 - -# Sound drivers -#VIA_SOUND = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - -# i386 options - -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Boot FILO from Multiboot loader (eg. GRUB) -#MULTIBOOT_IMAGE = 1 - Deleted: buildrom-devel/packages/filo/conf/qemu-Config =================================================================== --- buildrom-devel/packages/filo/conf/qemu-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/qemu-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,101 +0,0 @@ -# !!! NOTE !!! -# Do NOT add spaces or comments at the end of option lines. -# It confuses some versions of make. - -# Use grub instead of autoboot? -USE_GRUB = 1 - -# Grub menu.lst path -MENULST_FILE = "hda3:/boot/filo/menu.lst" -# Via Epia-MII CF boot: -#MENULST_FILE = "hde1:/boot/filo/menu.lst" - -# time before default menu.lst is chosen. Set to 0 to ignore -MENULST_TIMEOUT = 0 - -# Image filename for automatic boot and optional command line parameter -AUTOBOOT_FILE = "hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200" -#AUTOBOOT_FILE = "mem@0xfff80000" -#AUTOBOOT_FILE = "hde1@0" -#AUTOBOOT_FILE = "uda1:/vmlinuz.elf" - -# Time in second before booting AUTOBOOT_FILE -AUTOBOOT_DELAY = 2 - -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 - -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -# NOTE: Slows down access significantly, so disable -# whenever possible. -#IDE_DISK_POLL_DELAY = 1 - -# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E -# This device is referred to as hde. -#PCMCIA_CF = 1 - -# Driver for USB Storage -USB_DISK = 1 - -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 - -# Serial console -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -# if SERIAL_SPEED is commented out, the speed will not be changed. -#SERIAL_SPEED = 115200 - -# Filesystems -FSYS_EXT2FS = 1 -FSYS_FAT = 1 -#FSYS_JFS = 1 -#FSYS_MINIX = 1 -FSYS_REISERFS = 1 -#FSYS_XFS = 1 -FSYS_ISO9660 = 1 - -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 - -# PCI support -SUPPORT_PCI = 1 - -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 - -# Sound support (needs SUPPORT_PCI) -#SUPPORT_SOUND = 1 - -# Sound drivers -#VIA_SOUND = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - -# i386 options - -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Boot FILO from Multiboot loader (eg. GRUB) -#MULTIBOOT_IMAGE = 1 - Deleted: buildrom-devel/packages/filo/conf/serengeti_cheetah-Config =================================================================== --- buildrom-devel/packages/filo/conf/serengeti_cheetah-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/serengeti_cheetah-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,99 +0,0 @@ -# !!! NOTE !!! -# Do NOT add spaces or comments at the end of option lines. -# It confuses some versions of make. - -# Use grub instead of autoboot? -USE_GRUB = 1 - -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/filo/menu.lst" - -# time before default menu.lst is chosen. Set to 0 to ignore -MENULST_TIMEOUT = 0 - -# Image filename for automatic boot and optional command line parameter -AUTOBOOT_FILE = "hda1:/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200" -#AUTOBOOT_FILE = "mem@0xfff80000" -#AUTOBOOT_FILE = "hde1@0" -#AUTOBOOT_FILE = "uda1:/vmlinuz.elf" - -# Time in second before booting AUTOBOOT_FILE -AUTOBOOT_DELAY = 2 - -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 - -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -# NOTE: Slows down access significantly, so disable -# whenever possible. -#IDE_DISK_POLL_DELAY = 1 - -# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E -# This device is referred to as hde. -#PCMCIA_CF = 1 - -# Driver for USB Storage -# USB_DISK = 1 - -# VGA text console - VGA_CONSOLE = 1 - PC_KEYBOARD = 1 - -# Serial console -SERIAL_CONSOLE = 1 -SERIAL_IOBASE = 0x3f8 -# if SERIAL_SPEED is commented out, the speed will not be changed. -#SERIAL_SPEED = 115200 - -# Filesystems -FSYS_EXT2FS = 1 -FSYS_FAT = 1 -#FSYS_JFS = 1 -#FSYS_MINIX = 1 -FSYS_REISERFS = 1 -#FSYS_XFS = 1 -FSYS_ISO9660 = 1 - -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 - -# PCI support -SUPPORT_PCI = 1 - -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 - -# Sound support (needs SUPPORT_PCI) -#SUPPORT_SOUND = 1 - -# Sound drivers -#VIA_SOUND = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - -# i386 options - -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Boot FILO from Multiboot loader (eg. GRUB) -#MULTIBOOT_IMAGE = 1 - Deleted: buildrom-devel/packages/filo/conf/supermicro-h8dmr-Config =================================================================== --- buildrom-devel/packages/filo/conf/supermicro-h8dmr-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/supermicro-h8dmr-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hde1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/tyan-generic-Config =================================================================== --- buildrom-devel/packages/filo/conf/tyan-generic-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/tyan-generic-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/tyan-s2881-Config =================================================================== --- buildrom-devel/packages/filo/conf/tyan-s2881-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/tyan-s2881-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/tyan-s2882-Config =================================================================== --- buildrom-devel/packages/filo/conf/tyan-s2882-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/tyan-s2882-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Deleted: buildrom-devel/packages/filo/conf/tyan-s2891-Config =================================================================== --- buildrom-devel/packages/filo/conf/tyan-s2891-Config 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/conf/tyan-s2891-Config 2008-09-12 17:18:00 UTC (rev 226) @@ -1,50 +0,0 @@ -# Use grub instead of autoboot? -USE_GRUB = 1 -# Grub menu.lst path -MENULST_FILE = "hda1:/boot/grub/menu.lst" -# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus -IDE_DISK = 1 -# Add a short delay when polling status registers -# (required on some broken SATA controllers) -IDE_DISK_POLL_DELAY = 1 -# Driver for USB Storage -USB_DISK = 1 -# VGA text console -VGA_CONSOLE = 1 -PC_KEYBOARD = 1 -# Enable the serial console -SERIAL_CONSOLE = 1 -# Serial console; real external serial port -SERIAL_IOBASE = 0x3f8 -SERIAL_SPEED = 115200 -# Filesystems -FSYS_EXT2FS = 1 -FSYS_ISO9660 = 1 -# Support for boot disk image in bootable CD-ROM (El Torito) -ELTORITO = 1 -# PCI support -SUPPORT_PCI = 1 -# Enable this to scan PCI busses above bus 0 -# AMD64 based boards do need this. -PCI_BRUTE_SCAN = 1 -# Loader for standard Linux kernel image, a.k.a. /vmlinuz -LINUX_LOADER = 1 - -# Debugging -#DEBUG_ALL = 1 -#DEBUG_ELFBOOT = 1 -#DEBUG_ELFNOTE = 1 -#DEBUG_LINUXBIOS = 1 -#DEBUG_MALLOC = 1 -#DEBUG_MULTIBOOT = 1 -#DEBUG_SEGMENT = 1 -#DEBUG_SYS_INFO = 1 -#DEBUG_TIMER = 1 -#DEBUG_BLOCKDEV = 1 -#DEBUG_PCI = 1 -#DEBUG_VIA_SOUND = 1 -#DEBUG_LINUXLOAD = 1 -#DEBUG_IDE = 1 -#DEBUG_USB = 1 -#DEBUG_ELTORITO = 1 - Modified: buildrom-devel/packages/filo/filo.mk =================================================================== --- buildrom-devel/packages/filo/filo.mk 2008-09-11 19:04:33 UTC (rev 225) +++ buildrom-devel/packages/filo/filo.mk 2008-09-12 17:18:00 UTC (rev 226) @@ -1,13 +1,11 @@ -FILO_URL=svn://coreboot.org/filo/branches/filo-0.5 -FILO_TAG=59 +FILO_URL=svn://coreboot.org/filo/trunk/filo +FILO_TAG=62 FILO_DIR=$(BUILD_DIR)/filo FILO_SRC_DIR=$(FILO_DIR)/svn FILO_STAMP_DIR=$(FILO_DIR)/stamps FILO_LOG_DIR=$(FILO_DIR)/logs -FILO_PATCHES=$(PACKAGE_DIR)/filo/patches/make.patch - ifeq ($(CONFIG_VERBOSE),y) FILO_FETCH_LOG=/dev/stdout FILO_BUILD_LOG=/dev/stdout @@ -22,6 +20,8 @@ ifeq ($(shell if [ -f $(PACKAGE_DIR)/filo/conf/customconfig--$(PAYLOAD)--$(COREBOOT_VENDOR)-$(COREBOOT_BOARD) ]; then echo 1; fi),1) FILO_CONFIG = customconfig--$(PAYLOAD)--$(COREBOOT_VENDOR)-$(COREBOOT_BOARD) +else + FILO_CONFIG = $(FILO_SRC_DIR)/configs/defconfig endif $(SOURCE_DIR)/$(FILO_TARBALL): @@ -35,28 +35,28 @@ @ tar -C $(FILO_DIR) -zxf $(SOURCE_DIR)/$(FILO_TARBALL) @ touch $@ -$(FILO_STAMP_DIR)/.patched: $(FILO_STAMP_DIR)/.unpacked - @ echo "Patching filo..." - @ $(BIN_DIR)/doquilt.sh $(FILO_SRC_DIR) $(FILO_PATCHES) - @ touch $@ +#$(FILO_STAMP_DIR)/.patched: $(FILO_STAMP_DIR)/.unpacked +# @ echo "Patching filo..." +# @ $(BIN_DIR)/doquilt.sh $(FILO_SRC_DIR) $(FILO_PATCHES) +# @ touch $@ -$(FILO_STAMP_DIR)/.configured: $(FILO_STAMP_DIR)/.patched - @ make -C $(FILO_SRC_DIR) config > $(FILO_BUILD_LOG) 2>&1 - @ cp $(PACKAGE_DIR)/filo/conf/$(FILO_CONFIG) $(FILO_SRC_DIR)/Config +$(FILO_STAMP_DIR)/.configured: $(FILO_STAMP_DIR)/.unpacked + @ cp $(FILO_CONFIG) $(FILO_SRC_DIR)/.config + @ make -C $(FILO_SRC_DIR) oldconfig > $(FILO_BUILD_LOG) 2>&1 + @ mkdir -p $(OUTPUT_DIR)/config/filo + @ cp $(FILO_SRC_DIR)/.config $(OUTPUT_DIR)/config/filo/config @ touch $@ -$(FILO_SRC_DIR)/filo.elf: $(FILO_STAMP_DIR)/.configured - @ echo "Building filo..." +$(FILO_SRC_DIR)/build/filo.elf: $(FILO_STAMP_DIR)/.configured ifeq ($(findstring customconfig,$(FILO_CONFIG)),customconfig) - @ echo "Using custom config $(PACKAGE_DIR)/filo/conf/$(FILO_CONFIG)" + @ echo "Using custom config $(FILO_CONFIG)" endif - @ make -C $(FILO_SRC_DIR) filo.elf > $(FILO_BUILD_LOG) 2>&1 - @ mkdir -p $(OUTPUT_DIR)/config/filo - @ cp $(FILO_SRC_DIR)/Config $(OUTPUT_DIR)/config/filo/ + @ echo "Building filo..." + @ make -C $(FILO_SRC_DIR) > $(FILO_BUILD_LOG) 2>&1 -$(FILO_STAMP_DIR)/.copied: $(FILO_SRC_DIR)/filo.elf +$(FILO_STAMP_DIR)/.copied: $(FILO_SRC_DIR)/build/filo.elf @ mkdir -p $(shell dirname $(PAYLOAD_ELF)) - @ cp $(FILO_SRC_DIR)/filo.elf $(PAYLOAD_ELF) + @ cp $(FILO_SRC_DIR)/build/filo.elf $(PAYLOAD_ELF) @ touch $@ $(FILO_STAMP_DIR) $(FILO_LOG_DIR): @@ -87,8 +87,8 @@ @ echo else @ echo "Configure filo..." - @ $(MAKE) -C $(FILO_SRC_DIR) config - @ cp -f $(FILO_SRC_DIR)/Config $(PACKAGE_DIR)/filo/conf/customconfig--$(PAYLOAD)--$(COREBOOT_VENDOR)-$(COREBOOT_BOARD) + @ $(MAKE) -C $(FILO_SRC_DIR) menuconfig + @ cp -f $(FILO_SRC_DIR)/.config $(PACKAGE_DIR)/filo/conf/customconfig--$(PAYLOAD)--$(COREBOOT_VENDOR)-$(COREBOOT_BOARD) @ echo @ echo "Your custom FILO config has been saved as " @ echo " $(PACKAGE_DIR)/filo/conf/customconfig--$(PAYLOAD)--$(COREBOOT_VENDOR)-$(COREBOOT_BOARD)"

1 0

Re: [coreboot] Boot order? [Was: Convert Assembly JMP to C]
by Jake Peavy 12 Sep '08

12 Sep '08

On 9/11/08, Joseph Smith <joe(a)settoplinux.org> wrote: > > > > > On Thu, 11 Sep 2008 23:53:04 +0200, Peter Stuge <peter(a)stuge.se> wrote: > > Joseph Smith wrote: > >> My JMP question is about copying a drives mbr to memory 0x7c00 and > >> or 0x0600 at 512 byte blocks. > > .. > >> What do you think? > > > > I think you should just use SeaBIOS. > > > > Nope. This will be a autoboot_mbr option of FILO. Here is how it will work: > > It will comb through each drive and attempt to boot the first drive with a > valid mbr signature bit (0xAA55). Maybe a slight delay for user > intervention, and then boot boot the drive based on the info in the mbr. > So, let me just expose my ignorance here, does Coreboot provide an interface like a traditional, proprietary BIOS which allows the user to configure different settings? Settings like boot order? Because I guess I don't understand the purpose behind the whole discussion. I would have expected Coreboot to work it's way down a prioritized list looking for boot media (MBR in x86). Is it accurate to replace the words "boot media" above with "payload"? Is MBR code (be it FILO, GRUB, whatever Windows' bootloader is called) a payload? TIA, -- -jp I wish I had a Kryptonite cross, because then you could keep both Dracula AND Superman away. deepthoughtsbyjackhandy.com

2 1

Re: [coreboot] FILO creating filo.conf
by Joseph Smith 12 Sep '08

12 Sep '08

On Fri, 12 Sep 2008 05:21:08 +0200, Peter Stuge <peter(a)stuge.se> wrote: > Joseph Smith wrote: >> FILO searches for a filo.conf file on the first drive it finds > > Scanning for drives has been considered before but always dismissed > because it will potentially take a very long time for FILO to start > if it needs to wait for drives to start. > Doesn't the drive have to start for FILO to invoke GRUB? > > As an optional feature, everyone pretty much said they want to be > able to do such a drive scan only a few days ago. Would be great if > you want to hack on it! :) > I do think this would be better approach. I don't think scanning a top level directory would take very long. It wouldn't scan sub directories. Especially when the first drive it finds in the first partition root directory is usually your "/boot" partition. How many files are there, not many. -- Thanks, Joseph Smith Set-Top-Linux www.settoplinux.org

4 4

Incorrect casting in romcc.
by Mats Erik Andersson 12 Sep '08

12 Sep '08

Hello all, after much backtracking I have identified an unexpected case of (implicit) casting where romcc fails miserably. I desire a computation uint16_t fn(uint8_t d); uint8_t data; data = 0; data += ( fn(0x10) >> 1 ) && 0x007f; where fn(0x10) == 0x1010. However, the actual outcome of the previous calculation is the value 0x01, instead of the expected 0x08. I does not help to provide an explicit casting data += (uint8_t) ( fn(0x10) >> 1) && 0x007f; since provably the incorrect increment 0x01 is still produced. The above code is to be used in i440bx/raminit.c, and if I make the only change in that code to replace the above calculation with the fixed, but intended case data += 0x08; then the full functionality is restored and coreboot can start. In the light of all this, I mean to have found a bug in romcc, unless this can be viewed as a documented shortcoming. Best regards, Mats Erik Andersson

6 7

[PATCH] libpayload: Update FILO to the trun
by Jordan Crouse 12 Sep '08

12 Sep '08

Attached patch updates the FILO in buildrom to the brand new edition. By IRC concensus, filo-0.5 support has been removed entirely. -- Jordan Crouse Systems Software Development Engineer Advanced Micro Devices, Inc.

2 1

Is my system supported?
by Jason Craven 12 Sep '08

12 Sep '08

Wondering if coreboot support is available for my system, if so which version and special options (if any)? Here's my configuration from dmidecode: # dmidecode 2.9 SMBIOS 2.4 present. 34 structures occupying 3234 bytes. Table at 0x000F0000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Phoenix Technologies, LTD Version: 5.13 Release Date: 02/16/2007 Address: 0xE0000 Runtime Size: 128 kB ROM Size: 512 kB Characteristics: ISA is supported PCI is supported PNP is supported APM is supported BIOS is upgradeable BIOS shadowing is allowed Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/360 KB floppy services are supported (int 13h) 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 KB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Function key-initiated network boot is supported Targeted content distribution is supported BIOS Revision: 5.13 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Compaq-Presario Product Name: RX897AA-ABA SR5050NX Version: Serial Number: CNX7100ZSL UUID: 00C35532-C13B-1210-9B1F-E6E8EE56833F Wake-up Type: Power Switch SKU Number: RX897AA#ABA Family: 103C_53316J Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: ASUSTek Computer INC. Product Name: LEONITE Version: 5.00 Serial Number: MS1C71S43005394 Handle 0x0003, DMI type 3, 17 bytes Chassis Information Manufacturer: Hewlett-Packard Type: Desktop Lock: Not Present Version: 1111 Serial Number: Asset Tag: Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: Socket 775 Type: Central Processor Family: Other Manufacturer: Intel ID: 65 0F 00 00 FF FB EB BF Version: Intel(R) Pentium(R) D CPU 3.00GHz Voltage: 0.0 V External Clock: 200 MHz Max Speed: 3800 MHz Current Speed: 3000 MHz Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x000A L2 Cache Handle: 0x000B L3 Cache Handle: 0x000C Serial Number: Asset Tag: Part Number: Handle 0x0005, DMI type 5, 24 bytes Memory Controller Information Error Detecting Method: 8-bit Parity Error Correcting Capabilities: None Supported Interleave: One-way Interleave Current Interleave: One-way Interleave Maximum Memory Module Size: 1024 MB Maximum Total Memory Size: 4096 MB Supported Speeds: Other Supported Memory Types: Other Memory Module Voltage: 5.0 V Associated Memory Slots: 4 0x0006 0x0007 0x0008 0x0009 Enabled Error Correcting Capabilities: None Handle 0x0006, DMI type 6, 12 bytes Memory Module Information Socket Designation: A0 Bank Connections: 0 1 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Double-bank Connection) Enabled Size: 1024 MB (Double-bank Connection) Error Status: OK Handle 0x0007, DMI type 6, 12 bytes Memory Module Information Socket Designation: A1 Bank Connections: 2 3 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Double-bank Connection) Enabled Size: 1024 MB (Double-bank Connection) Error Status: OK Handle 0x0008, DMI type 6, 12 bytes Memory Module Information Socket Designation: A2 Bank Connections: 4 5 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Double-bank Connection) Enabled Size: 1024 MB (Double-bank Connection) Error Status: OK Handle 0x0009, DMI type 6, 12 bytes Memory Module Information Socket Designation: A3 Bank Connections: 6 7 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Double-bank Connection) Enabled Size: 1024 MB (Double-bank Connection) Error Status: OK Handle 0x000A, DMI type 7, 19 bytes Cache Information Socket Designation: L1 Cache Configuration: Enabled, Not Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 16 KB Maximum Size: 16 KB Supported SRAM Types: Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Single-bit ECC System Type: Data Associativity: 4-way Set-associative Handle 0x000B, DMI type 7, 19 bytes Cache Information Socket Designation: L2 Cache Configuration: Enabled, Not Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 2048 KB Maximum Size: 2048 KB Supported SRAM Types: Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Single-bit ECC System Type: Unified Associativity: 4-way Set-associative Handle 0x000C, DMI type 7, 19 bytes Cache Information Socket Designation: L3 Cache Configuration: Disabled, Not Socketed, Level 3 Operational Mode: Varies With Memory Address Location: Internal Installed Size: 0 KB Maximum Size: 0 KB Supported SRAM Types: Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown Handle 0x000D, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Line In Internal Connector Type: None External Reference Designator: Line In External Connector Type: None Port Type: Audio Port Handle 0x000E, DMI type 9, 13 bytes System Slot Information Designation: PCI1 Type: 32-bit PCI Current Usage: In Use Length: Short ID: 1 Characteristics: 5.0 V is provided PME signal is supported Handle 0x000F, DMI type 9, 13 bytes System Slot Information Designation: PCI2 Type: 32-bit PCI Current Usage: In Use Length: Short ID: 2 Characteristics: 5.0 V is provided PME signal is supported Handle 0x0010, DMI type 9, 13 bytes System Slot Information Designation: PCI3 Type: 32-bit PCI Current Usage: Available Length: Short ID: 3 Characteristics: 5.0 V is provided PME signal is supported Handle 0x0011, DMI type 9, 13 bytes System Slot Information Designation: PCIEX16 Type: x16 PCI Express Current Usage: Available Length: Short ID: 6 Characteristics: 5.0 V is provided PME signal is supported Handle 0x0012, DMI type 10, 6 bytes On Board Device Information Type: Sound Status: Enabled Description: Intel(R) HD Audio Handle 0x0013, DMI type 13, 22 bytes BIOS Language Information Installable Languages: 3 n|US|iso8859-1 n|US|iso8859-1 r|CA|iso8859-1 Currently Installed Language: n|US|iso8859-1 Handle 0x0014, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0015, DMI type 17, 27 bytes Memory Device Array Handle: 0x0014 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A0 Bank Locator: Bank0/1 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz (1.5 ns) Manufacturer: None Serial Number: None Asset Tag: None Part Number: None Handle 0x0016, DMI type 17, 27 bytes Memory Device Array Handle: 0x0014 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A1 Bank Locator: Bank2/3 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz (1.5 ns) Manufacturer: None Serial Number: None Asset Tag: None Part Number: None Handle 0x0017, DMI type 17, 27 bytes Memory Device Array Handle: 0x0014 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A2 Bank Locator: Bank4/5 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz (1.5 ns) Manufacturer: None Serial Number: None Asset Tag: None Part Number: None Handle 0x0018, DMI type 17, 27 bytes Memory Device Array Handle: 0x0014 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A3 Bank Locator: Bank6/7 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz (1.5 ns) Manufacturer: None Serial Number: None Asset Tag: None Part Number: None Handle 0x0019, DMI type 19, 15 bytes Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x000FFFFFFFF Range Size: 4 GB Physical Array Handle: 0x0014 Partition Width: 0 Handle 0x001A, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0003FFFFFFF Range Size: 1 GB Physical Device Handle: 0x0015 Memory Array Mapped Address Handle: 0x0019 Partition Row Position: 1 Handle 0x001B, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00040000000 Ending Address: 0x0007FFFFFFF Range Size: 1 GB Physical Device Handle: 0x0016 Memory Array Mapped Address Handle: 0x0019 Partition Row Position: 1 Handle 0x001C, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000BFFFFFFF Range Size: 1 GB Physical Device Handle: 0x0017 Memory Array Mapped Address Handle: 0x0019 Partition Row Position: 1 Handle 0x001D, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x000C0000000 Ending Address: 0x000FFFFFFFF Range Size: 1 GB Physical Device Handle: 0x0018 Memory Array Mapped Address Handle: 0x0019 Partition Row Position: 1 Handle 0x001E, DMI type 32, 11 bytes System Boot Information Status: No errors detected Handle 0x0020, DMI type 12, 5 bytes System Configuration Options Option 1: 0011D80001256622 Handle 0x001F, DMI type 11, 5 bytes OEM Strings String 1: bid=72NAv3PrA2;PROD_MSWORKS;SFCHK;DLED;RP_STD;IS.N60d;ACPwrFail= String 2: Off;Chan=Retail;CPUFan=On;DVDRW;LegacyFloppy=No;TVout=NTSC;PCBRA String 3: ND=Presario;OS=MSV;KBDRV;LScribe;ELAKE;AOL_MN;Vos.P;MDVD_B;RC_B; String 4: FPA=HML;C_MAR;.ER;##HPCPC=00000000<90000006020000000420000253514 String 5: 130040000010001000;5;:0665<;85>18>1<2=1:<55>?4;;=?=19:<8494;>:80 String 6: 11<=31953=?76?>378139;594701:=;34:;55;9128<7937==0<722<:<1:2489> String 7: :088=6:?1;2>8=8>12691>>286:9?;4454>3<3>89909>=738375;02951<;>=?? String 8: 2?70>75;04<815:33<20846?312127;?24876>7488457<0;0?39>9;?407;8;8; String 9: 09>=;==>231>;?456:100000006;00000000002000840515?454=435<49434=2 String 10: 3405347594>444?47535020000000000000000000000000000000000000000?2 String 11: 4?41954<8?4243:463542:9034;??09<31;8951=>:><6>3291=35:7;:7?<0;=9 String 12: 73478<4:062629<>53103<<=4651<3499:7?769::98;357697=:3483>07=6;>1 String 13: <1?<>7<817?5586>79?5:5?19<87:>=6507148017=835>552096;714776===1= String 14: 59:5:9;7?16>;910;6<?>4?;=21?;7975:6660><>729>:9<98<5<=991>7?7> String 15: String 16: String 17: String 18: String 19: String 20: String 21: String 22: String 23: String 24: String 25: String 26: String 27: String 28: String 29: String 30: String 31: String 32: Handle 0x0021, DMI type 127, 4 bytes End Of Table

2 1

← Newer
1
...
27
28
29
30
31
32
33
...
42
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot September 2008