coreboot December 2004

coreboot@coreboot.org

33 participants
95 discussions

Start a nNew thread

K8 D0 support
by YhLu 03 Dec '04

03 Dec '04

Eric, Are you working on Opteron D0 support? There are some memory initialization changes to support D0... YH

2 1

k8 cpu rev
by YhLu 03 Dec '04

03 Dec '04

northbridge/amd/amdk8/cpu_rev.c static int is_cpu_pre_c0(void) { return (cpuid_eax(1) & 0xffef) < 0x0f48; } Why need to and 0xffef? YH

2 1

Substractive Resource
by Li-Ta Lo 03 Dec '04

03 Dec '04

Eric, You explained substractive decoding to me long time ago but I really forgot what it is. Could you tell me again ? Hoe do you determine if some resource of some device is substractive ? Form the data sheet ? Ollie

2 1

amd8111_nic fix
by Liu Tao 02 Dec '04

02 Dec '04

Hello, On my board I have amd8111 nic + realtek 8201 PHY, but 8111nic use active high reset signal to reset PHY while RTL8201 accepts active low reset signal. However amd8111 nic provides PHY_RESET_POLARITY bit in CMD3 register, so I add the "phy_lowreset" register to handle this. attached is the patch. Regards, Liu Tao

1 0

RE: print_smbus_regs_all
by YhLu 02 Dec '04

02 Dec '04

Just committed. i2c mux support CVS: ---------------------------------------------------------------------- CVS: Enter Log. Lines beginning with `CVS:' are removed automatically CVS: CVS: Committing in . CVS: CVS: Modified Files: CVS: devices/Config.lb drivers/generic/debug/debug_dev.c CVS: include/device/device.h include/device/smbus.h CVS: mainboard/tyan/s2885/Config.lb mainboard/tyan/s2885/auto.c CVS: mainboard/tyan/s2885/irq_tables.c CVS: mainboard/tyan/s4882/Config.lb northbridge/amd/amdk8/debug.c CVS: southbridge/amd/amd8111/amd8111_acpi.c CVS: Added Files: CVS: devices/smbus_ops.c drivers/i2c/adm1026/Config.lb CVS: drivers/i2c/adm1026/adm1026.c drivers/i2c/adm1026/chip.h CVS: drivers/i2c/adm1027/Config.lb drivers/i2c/adm1027/adm1027.c CVS: drivers/i2c/adm1027/chip.h drivers/i2c/i2cmux/Config.lb CVS: drivers/i2c/i2cmux/chip.h drivers/i2c/i2cmux/i2cmux.c CVS: drivers/i2c/lm63/Config.lb drivers/i2c/lm63/chip.h CVS: drivers/i2c/lm63/lm63.c CVS: ---------------------------------------------------------------------- -----Original Message----- From: YhLu Sent: Wednesday, December 01, 2004 2:18 PM To: ebiederman(a)lnxi.com Cc: linuxbios(a)clustermatic.org Subject: RE: print_smbus_regs_all Please check the code. I add set_link member to switch link on i2mux. Regards YH -----Original Message----- From: ebiederman(a)lnxi.com [mailto:ebiederman@lnxi.com] Sent: Wednesday, December 01, 2004 1:49 PM To: YhLu Cc: linuxbios(a)clustermatic.org Subject: Re: print_smbus_regs_all YhLu <YhLu(a)tyan.com> writes: > I add some code to debug_device to dump smbus for S4882. > > Please let me know if you need me to commit it. I don't know about need but I think it could be handy to have. Especially as we don't have many users of i2c code in the tree at the present time. Eric

1 0

to 694X-686A chipset
by yangzonghui＠KONKA.COM 02 Dec '04

02 Dec '04

hi,all: please tell me whether freebios can be installed on the machine of 694X-686A chipset, and anything special to do as the document included in project directory. thanks ! yang

1 0

(no subject)
by yangzonghui＠KONKA.COM 02 Dec '04

02 Dec '04

hi,all: please tell me whether freebios can be installed on the machine of 694X-686A chipset, and anything special to do as the document included in project directory. thanks ! yang

1 0

devices/pci_devices.c
by mark.wilkinson＠2pmtech.com 01 Dec '04

01 Dec '04

Hi Eric, Ron, I noticed what might be a slight problem with some error messages in the pci_level_irq routine. When it reports the new settings, it masks off the lower nibble of intBits to compare against the byte read. If an interrupt line is set in the upper nibble of the byte, then the error message will always be displayed even if the setting was successful. I've included a diff that should fix the masks. Regards Mark Wilkinson. ---------------------------------------------------------------- This message was sent using ISPMailNow.com

1 0

irq routing table
by Gin 01 Dec '04

01 Dec '04

If I have a wrong checksum for my irq routing table, would that stops me from booting successfully? The question should be, does the irq_routing table matter at all? Linuxbios runs through till it jumps to the entry of payload. I am just trying to figure out why. Gin

2 1

RE: print_smbus_regs_all
by YhLu 01 Dec '04

01 Dec '04

Please check the code. I add set_link member to switch link on i2mux. Regards YH -----Original Message----- From: ebiederman(a)lnxi.com [mailto:ebiederman@lnxi.com] Sent: Wednesday, December 01, 2004 1:49 PM To: YhLu Cc: linuxbios(a)clustermatic.org Subject: Re: print_smbus_regs_all YhLu <YhLu(a)tyan.com> writes: > I add some code to debug_device to dump smbus for S4882. > > Please let me know if you need me to commit it. I don't know about need but I think it could be handy to have. Especially as we don't have many users of i2c code in the tree at the present time. Eric

1 0

← Newer
1
2
3
4
5
6
7
8
9
10
Older →

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot December 2004