[LinuxBIOS] VIA EPIA MII6000E

[Wojciech Kromer]

I've followed instuctions in EPIA-M-howto, but can't boot anything.

How could I boot from cdrom now???
What is correct syntax in command line grub (filo-grub)

LinuxBIOS-1.1.8.0Fallback pon cze 12 12:33:20 CEST 2006 starting...
 Enabling mainboard devices
 Enabling shadow ram
vt8623 init starting
Detecting Memory
Number of Banks 04
Number of Rows 0d
Priamry DRAM width08
No Columns 0a
MA type e0
Bank 0 (*16 Mb) 10
No Physical Banks 01
Total Memory (*16 Mb) 10
CAS Supported 2 2.5 3
Cycle time at CL X     (nS)50
Cycle time at CL X-0.5 (nS)60
Cycle time at CL X-1   (nS)75
Starting at CAS 3
We can do CAS 2.5
We can do CAS 2
tRP 3c
tRCD 3c
tRAS 28
Low Bond 06  High Bondd0  Setting DQS delay8cvt8623 done
00:06 11 23 31 06 00 30 22 00 00 00 06 00 00 00 00
10:08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30:00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40:00 18 88 80 82 44 00 00 18 99 88 80 82 44 00 00
50:c8 de cf 88 e0 07 00 00 e0 00 10 10 10 10 00 00
60:02 ff 00 30 52 32 01 20 42 2d 43 58 00 44 00 00
70:82 48 00 01 01 08 50 00 01 00 00 00 00 00 02 02
80:0f 61 00 00 80 00 00 00 02 00 00 00 00 00 00 00
90:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0:02 c0 20 00 07 02 00 1f 04 00 00 00 2f 02 04 00
b0:00 00 00 00 80 00 00 00 a8 00 00 00 00 00 00 00
c0:01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0:00 dd 00 00 00 00 01 00 40 00 00 00 00 00 00 00
f0:00 00 00 00 00 00 12 13 00 00 00 00 00 00 00 00
AGP
 Doing MTRR init.
Copying LinuxBIOS to ram.
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8.0Fallback pon cze 12 12:33:20 CEST 2006 booting...
clocks_per_usec: 941
Enumerating buses...
Finding PCI configuration type.
PCI: Using configuration type 1
PCI_DOMAIN: 0000 enabled
APIC_CLUSTER: 0 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1106/3123] enabled
PCI: 00:01.0 [1106/b091] enabled
PCI: 00:0a.0 [1180/0476] enabled
PCI: 00:0a.1 [1180/0476] enabled
In vt8235_enable 1106 3038.
PCI: 00:10.0 [1106/3038] enabled
In vt8235_enable 1106 3038.
PCI: 00:10.1 [1106/3038] enabled
In vt8235_enable 1106 3038.
PCI: 00:10.2 [1106/3038] enabled
In vt8235_enable 1106 3104.
PCI: 00:10.3 [1106/3104] enabled
In vt8235_enable 1106 3177.
Initialising Devices
PCI: 00:11.0 [1106/3177] enabled
In vt8235_enable 1106 0571.
PCI: 00:11.1 [1106/0571] enabled
In vt8235_enable 1106 3059.
PCI: 00:11.5 [1106/3059] enabled
In vt8235_enable ffff ffff.
In vt8235_enable 1106 3065.
PCI: 00:12.0 [1106/3065] enabled
PCI: pci_scan_bus for bus 1
PCI: 01:00.0 [1106/3122] enabled
PCI: pci_scan_bus returning with max=01
PCI: pci_scan_bus for bus 2
PCI: pci_scan_bus returning with max=02
PCI: pci_scan_bus for bus 3
PCI: pci_scan_bus returning with max=03
vt1211 enabling PNP devices.
PNP: 002e.0 enabled
vt1211 enabling PNP devices.
PNP: 002e.1 enabled
vt1211 enabling PNP devices.
PNP: 002e.2 enabled
vt1211 enabling PNP devices.
PNP: 002e.3 enabled
vt1211 enabling PNP devices.
PNP: 002e.b enabled
PCI: pci_scan_bus returning with max=03
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
I would set ram size to 0x40000 Kbytes
PCI: 00:0a.0 In set resources
PCI: 00:0a.0 10 <- [0x00febfb000 - 0x00febfbfff] mem
PCI: 00:0a.0 2c <- [0x0000001870 - 0x000000286f] io
PCI: 00:0a.0 34 <- [0x0000002870 - 0x000000386f] io
PCI: 00:0a.0 1c <- [0x00f6bfb000 - 0x00f8bfafff] prefmem
PCI: 00:0a.0 24 <- [0x00f8bfb000 - 0x00fabfafff] mem
PCI: 00:0a.1 In set resources
PCI: 00:0a.1 1 ==> febfc000
PCI: 00:0a.1 10 <- [0x00febfd000 - 0x00febfdfff] mem
PCI: 00:0a.1 2c <- [0x0000003870 - 0x000000486f] io
PCI: 00:0a.1 34 <- [0x0000004870 - 0x000000586f] io
PCI: 00:0a.1 1c <- [0x00fabfb000 - 0x00fcbfafff] prefmem
PCI: 00:0a.1 24 <- [0x00fcbfb000 - 0x00febfafff] mem
PCI: 00:10.0 20 <- [0x0000001800 - 0x000000181f] io
PCI: 00:10.1 20 <- [0x0000001820 - 0x000000183f] io
PCI: 00:10.2 20 <- [0x0000001840 - 0x000000185f] io
PCI: 00:10.3 10 <- [0x00febfe000 - 0x00febfe0ff] mem
PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] io
PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq
PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq
PNP: 002e.1 60 <- [0x0000000378 - 0x000000037f] io
PNP: 002e.1 70 <- [0x0000000007 - 0x0000000007] irq
PNP: 002e.1 74 <- [0x0000000003 - 0x0000000003] drq
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.3 60 <- [0x00000002f8 - 0x00000002ff] io
PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq
PNP: 002e.b 60 <- [0x000000ec00 - 0x000000ecff] io
PCI: 00:11.1 20 <- [0x0000001860 - 0x000000186f] io
PCI: 00:11.5 10 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:12.0 10 <- [0x0000001400 - 0x00000014ff] io
PCI: 00:12.0 14 <- [0x00febff000 - 0x00febff0ff] mem
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:00.0 cmd <- 146
PCI: 00:01.0 bridge ctrl <- 000f
PCI: 00:01.0 cmd <- 147
PCI: 01:00.0 cmd <- 140
PCI: 00:0a.0 bridge ctrl <- 0503
PCI: 00:0a.0 cmd <- 143
PCI: 00:0a.1 bridge ctrl <- 0503
PCI: 00:0a.1 cmd <- 143
PCI: 00:10.0 subsystem <- 00/00
PCI: 00:10.0 cmd <- 141
PCI: 00:10.1 subsystem <- 00/00
PCI: 00:10.1 cmd <- 141
PCI: 00:10.2 subsystem <- 00/00
PCI: 00:10.2 cmd <- 141
PCI: 00:10.3 subsystem <- 00/00
PCI: 00:10.3 cmd <- 142
PCI: 00:11.0 cmd <- 147
PNP: 002e.0 - enabling
PNP: 002e.1 - enabling
PNP: 002e.2 - enabling
PNP: 002e.3 - enabling
PNP: 002e.b - enabling
PCI: 00:11.1 cmd <- 147
PCI: 00:11.5 subsystem <- 00/00
PCI: 00:11.5 cmd <- 141
PCI: 00:12.0 cmd <- 1c3
done.
Initializing devices...
Root Device init
PCI: 00:10.0 init
PCI: 00:10.1 init
PCI: 00:10.2 init
PCI: 00:10.3 init
PCI: 00:11.0 init
vt8235 init
RTC Init
Invalid CMOS LB checksum
pci_routing_fixup: dev is 000111a0
setting firewire
setting usb
Assigning IRQ 5 to 0:10.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 9 to 0:10.1
  Readback = 9
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 9 to 0:10.2
  Readback = 9
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 5 to 0:10.3
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting vt8235
Assigning IRQ 5 to 0:11.1
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 9 to 0:11.5
  Readback = 9
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting ethernet
Assigning IRQ 5 to 0:12.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting vga
Assigning IRQ 5 to 1:0.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
setting pci slot
setting cardbus slot
Assigning IRQ 5 to 0:a.0
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20
Assigning IRQ 5 to 0:a.1
  Readback = 5
pci_level_irq: lower order bits are wrong: want 0x0, got 0x20

^^^^ why? any missconfiguration?

setting riser slot
PNP: 002e.0 init
PNP: 002e.1 init
PNP: 002e.2 init
PNP: 002e.3 init
PNP: 002e.b init
PCI: 00:11.1 init
Enabling VIA IDE.
ide_init: enabling compatibility IDE addresses
enables in reg 0x42 0x0
enables in reg 0x42 read back as 0x0
enables in reg 0x40 0x13
enables in reg 0x40 read back as 0x13
enables in reg 0x9 0x8a
enables in reg 0x9 read back as 0x8a
command in reg 0x4 0x7
command in reg 0x4 reads back as 0x7

^^^^ is it wrong ????

PCI: 00:11.5 init
PCI: 00:12.0 init
Configuring VIA Rhine LAN
PCI: 00:0a.0 init
rl5c476 init
CF Base = febfc000
PCI: 00:0a.1 init
rl5c476 init
CF Base = febfc000
CF Config = 0
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor Centaur device 673
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB
Setting fixed MTRRs(24-88) Type: WB
DONE fixed MTRRs
Setting variable MTRR 0, base:    0MB, range:  128MB, type WB
Setting variable MTRR 1, base:  128MB, range:   64MB, type WB
Setting variable MTRR 2, base:  192MB, range:   32MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

Disabling local apic...done.
CPU #0 Initialized
PCI: 00:00.0 init
VT8623 random fixup ...
Frame buffer at d0000000
PCI: 00:01.0 init
VT8623 AGP random fixup ...
PCI: 01:00.0 init
VGA random fixup ...
INSTALL REAL-MODE IDT
DO THE VGA BIOS
found VGA: vid=1106, did=3122
rom base, size: fffc0000
BAD SIGNATURE 0xb4 0x0

^^^^^ why? I grab vide.bios.rom just as in howto, and changed 
everything...

biosint: INT# 0x10
biosint: eax 0x4f14 ebx 0x18003 ecx 0x1 edx 0x0
biosint: ebp 0x17fa8 esp 0xffa edi 0x0 esi 0xffff7063
biosint:  ip 0xbb85   cs 0x0  flags 0x46
BIOSINT: Unsupport int #0x10
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...done
Checking IRQ routing table consistency...
check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
done
ACPI: Writing ACPI tables at f0400...
ACPI:     * FACS
ACPI:     * DSDT @ 000f049e Length 3f0
ACPI:     * FADT
ACPI: added table 1/5 Length now 40
ACPI: done.
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 00000b70  checksum 3245

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

rom_stream: 0xfffd0000 - 0xfffeffff
Found ELF candiate at offset 0
New segment addr 0x100000 size 0x3ca40 offset 0xc0 filesize 0x12c48
(cleaned up) New segment addr 0x100000 size 0x3ca40 offset 0xc0 filesize 
0x12c48New segment addr 0x13ca40 size 0x48 offset 0x12d20 filesize 0x48
(cleaned up) New segment addr 0x13ca40 size 0x48 offset 0x12d20 filesize 
0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x0000000000100000 memsz: 0x000000000003ca40 
filesz: 0x00Clearing Segment: addr: 0x0000000000112c48 memsz: 
0x0000000000029df8
Loading Segment: addr: 0x000000000013ca40 memsz: 0x0000000000000048 
filesz: 0x00Jumping to boot code at 0x10e408
FILO version 0.5 ([e-mail]) pon cze 12 10:55:25 CEST 2006
menu: hda3:/boot/filo/menu.lst
            ^^^ this is my mistake, should be hde1:/boot/filo/menu.lst 
for CF
                  but i want to boot anything now....

hda: ATAPI: HL-DT-ST DVDRAM GSA-4167B
Waiting for drive to detect the medium... 50MB medium detected
El-Torito entries other than Initial/Default is not supported
Press any key to continue.
......