New subject: [COMMIT] freebios2 How much have I broken?

13 Oct 2003


      Eric,
After changed to following,
    PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0x00000003,
    PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000,
    PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
    PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
LinuxBIOS-1.1.52.0_Fallback Tue Oct 14 01:12:13 EDT 2003 starting...
setting up resource map....
done.
Enabling routing table for node 00000000 done.
Enabling SMP settings
setup_remote_node
setup_remote_done
Renaming current temp node to 00000001 done.
Enabling routing table for node 00000001 done.
00000002 nodes initialized.
detect_mp_capabilities: 00000002
coherent_ht_finalize
done
setting up ht links....
done
Copying LinuxBIOS to ram.
SMBUS controller not found
So it seems it can not access the SMBUS and init the RAM anymore.
Regards
YH.
-----邮件原件-----
发件人: ebiederman@lnxi.com [mailto:ebiederman@lnxi.com] 
发送时间: 2003年10月13日 18:30
收件人: YhLu
抄送: LinuxBIOS
主题: Re: R: [COMMIT] freebios2 How much have I broken?
Ok. I see what the symptoms are and I think I have a clue about
what is going on.  It is going to take me a little bit to see what I can
to fix the problem well enough so it will not recur.
/* Config Base and Limit i Registers
     * F1:0xE0 i = 0
     * F1:0xE4 i = 1
     * F1:0xE8 i = 2
     * F1:0xEC i = 3
     * [ 0: 0] Read Enable
     *         0 = Reads Disabled
     *         1 = Reads Enabled
     * [ 1: 1] Write Enable
     *         0 = Writes Disabled
     *         1 = Writes Enabled
     * [ 2: 2] Device Number Compare Enable
     *         0 = The ranges are based on bus number
     *         1 = The ranges are ranges of devices on bus 0
     * [ 3: 3] Reserved
     * [ 6: 4] Destination Node
     *         000 = Node 0
     *         001 = Node 1
     *         010 = Node 2
     *         011 = Node 3
     *         100 = Node 4
     *         101 = Node 5
     *         110 = Node 6
     *         111 = Node 7
     * [ 7: 7] Reserved
     * [ 9: 8] Destination Link
     *         00 = Link 0
     *         01 = Link 1
     *         10 = Link 2
     *         11 - Reserved
     * [15:10] Reserved
     * [23:16] Bus Number Base i
     *         This field defines the lowest bus number in configuration
region i
     * [31:24] Bus Number Limit i
     *         This field defines the highest bus number in
configuration regin i
     */
    PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0x04000203,
    PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x06050003,
    PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
    PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
You start out with:
 busses 0 - 4 mapped to node 0 link 2
 busses 5 - 6 mapped to node 0 link 0
All other busses disabled.
In northbridge.c:amdk8_scan_chains
For link 0 I scan through and find that register 0xE4 is used for node 0
link 0.
I then pick the next free bus number one and assign that to node 0 link 0,
in 
register 0xE4.
But bus 1 is still routed in register 0xE0 to node 0 link 2.  I believe 0xE0
comes
first and overrides my logic.  Either that or the cpu is confused because
there
are two inconsistent mappings for bus 1.
So there look to be two fixes.
1) In resourcemap.c just map bus 0 to the node 0 link 0, and leave
everything else unmapped.
2) Modify the bus scanning code to unmap busses beyond it's current maximum,
so we do
   not get ambiguous mappings.
Either one should allow the busses to be scanned in either order.
I will think through and see if I can code the second fix properly, as it
will just
save grief.  If you can try the simpler solution, I would appreciate it.
Eric

Re: [COMMIT] freebios2 How much have I broken?