On Sat, Nov 10, 2007 at 05:04:32PM +0100, Carl-Daniel Hailfinger wrote:
Hi Andi,
Can you try this patch on top of the existing patch? It will give you better debug output for superio config.
......
Can you then post the serial boot log (minicom capture)? It should have a few lines with "TRACE:" in it. Then we can check whether the values are set or not.
Hi Carl-Daniel,
here are the results, I have not looked into details yet, but the TRACE is there:
LinuxBIOS-2.0.0_m57sli_Fallback Sat Nov 10 20:04:37 CET 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107121207110202 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 ht reset -
LinuxBIOS-2.0.0_m57sli_Fallback Sat Nov 10 20:04:37 CET 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107120707110210 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 Ram1.00 Ram2.00 Unbuffered 333Mhz Interleaved RAM: 0x00400000 KB Ram3 dimm_mask = 00000033 x4_mask = 00000000 x16_mask = 00000000 single_rank_mask = 00000000 ODC = 00111322 Addr Timing= 002b2220 Initializing memory: done RAM: 0x00500000 KB Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB Setting variable MTRR 3, base: 2048MB, range: 1024MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=13 done set DQS timing:DQSPos: 00 done set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=34 done Total DQS Training : tsc [00]=0000000045b035fc Total DQS Training : tsc [01]=000000004760b7a6 Total DQS Training : tsc [02]=00000000de2ca1bf Total DQS Training : tsc [03]=00000000e067edff Ram4 v_esp=000ceea8 testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying LinuxBIOS to RAM. src=fffdf000 dst=00100000 linxbios_ram.nrv2b length = 0000d68c linxbios_ram.bin length = 000224ec Jumping to LinuxBIOS. LinuxBIOS-2.0.0_m57sli_Fallback Sat Nov 10 20:04:37 CET 2007 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled PCI: 00:18.3 siblings=1 CPU: APIC: 00 enabled CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 00 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:00.0 [10de/0369] enabled PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010 PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [10de/0369] enabled PCI: 00:01.0 [10de/0360] enabled PCI: 00:01.1 [10de/0368] enabled PCI: 00:01.2 [10de/036a] enabled PCI: 00:01.3 [10de/036b] enabled PCI: 00:02.0 [10de/036c] enabled PCI: 00:02.1 [10de/036d] enabled PCI: 00:04.0 [10de/036e] enabled PCI: 00:05.0 [10de/037f] enabled PCI: 00:05.1 [10de/037f] enabled PCI: 00:05.2 [10de/037f] enabled PCI: 00:06.0 [10de/0370] enabled PCI: 00:06.1 [10de/0371] enabled PCI: 00:08.0 [10de/0373] enabled PCI: 00:0a.0 [10de/0376] enabled PCI: 00:0b.0 [10de/0374] enabled PCI: 00:0c.0 [10de/0374] enabled PCI: 00:0d.0 [10de/0378] enabled PCI: 00:0e.0 [10de/0375] enabled PCI: 00:0f.0 [10de/0377] enabled PNP: 002e.0 disabled PNP: 002e.1 enabled PNP: 002e.2 disabled PNP: 002e.3 disabled PNP: 002e.4 enabled PNP: 002e.5 enabled PNP: 002e.6 enabled PNP: 002e.7 enabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled PCI: pci_scan_bus for bus 01 PCI: 01:07.0 [1102/0002] enabled PCI: 01:07.1 [1102/7002] enabled PCI: 01:0a.0 [104c/8024] enabled PCI: pci_scan_bus returning with max=001 PCI: pci_scan_bus for bus 02 PCI: pci_scan_bus returning with max=002 PCI: pci_scan_bus for bus 03 PCI: pci_scan_bus returning with max=003 PCI: pci_scan_bus for bus 04 PCI: pci_scan_bus returning with max=004 PCI: pci_scan_bus for bus 05 PCI: pci_scan_bus returning with max=005 PCI: pci_scan_bus for bus 06 PCI: pci_scan_bus returning with max=006 PCI: pci_scan_bus for bus 07 PCI: 07:00.0 [10de/0392] enabled PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 done Allocating resources... Reading resources... PNP: 002e.7 missing read_resources PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 01 prefmem PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 02 io PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 02 prefmem PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 02 mem PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 03 io PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 03 prefmem PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 03 mem PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 04 io PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 04 prefmem PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 04 mem PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 05 io PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 05 prefmem PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 05 mem PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 06 io PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 06 prefmem PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 06 mem Done reading resources. Allocating VGA resource PCI: 07:00.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0f.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000004fff] size 0x00004000 gran 0x0c io <node 0 link 0> PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] size 0x10000000 gran 0x14 prefmem <node 0 link 0> PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f62fffff] size 0x02300000 gran 0x14 mem <node 0 link 0> PCI: 00:01.0 14 <- [0x00f6244000 - 0x00f6244fff] size 0x00001000 gran 0x0c mem TRACE: PNP: 002e.1, selecting logical device 01 TRACE: PNP: 002e.1, index 60: writing 03f8 PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] size 0x00000008 gran 0x03 io TRACE: PNP: 002e.1, index 70: writing 0004 PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] size 0x00000001 gran 0x00 irq TRACE: PNP: 002e.4, selecting logical device 04 TRACE: PNP: 002e.4, index 60: writing 0290 PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] size 0x00000008 gran 0x03 io TRACE: PNP: 002e.4, index 62: writing 0230 PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] size 0x00000008 gran 0x03 io TRACE: PNP: 002e.4, index 70: writing 0009 PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] size 0x00000001 gran 0x00 irq TRACE: PNP: 002e.5, selecting logical device 05 TRACE: PNP: 002e.5, index 60: writing 0060 PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] size 0x00000001 gran 0x00 io TRACE: PNP: 002e.5, index 62: writing 0064 PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] size 0x00000001 gran 0x00 io TRACE: PNP: 002e.5, index 70: writing 0001 PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] size 0x00000001 gran 0x00 irq TRACE: PNP: 002e.6, selecting logical device 06 TRACE: PNP: 002e.6, index 70: writing 000c PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] size 0x00000001 gran 0x00 irq PNP: 002e.7 missing set_resources PCI: 00:01.1 10 <- [0x0000003c00 - 0x0000003c3f] size 0x00000040 gran 0x06 io PCI: 00:01.1 20 <- [0x0000003c40 - 0x0000003c7f] size 0x00000040 gran 0x06 io PCI: 00:01.1 24 <- [0x0000003c80 - 0x0000003cbf] size 0x00000040 gran 0x06 io PCI: 00:01.1 60 <- [0x0000003000 - 0x00000030ff] size 0x00000100 gran 0x08 io PCI: 00:01.1 64 <- [0x0000003400 - 0x00000034ff] size 0x00000100 gran 0x08 io PCI: 00:01.1 68 <- [0x0000003800 - 0x00000038ff] size 0x00000100 gran 0x08 io PCI: 00:01.3 10 <- [0x00f6200000 - 0x00f623ffff] size 0x00040000 gran 0x12 mem PCI: 00:02.0 10 <- [0x00f6245000 - 0x00f6245fff] size 0x00001000 gran 0x0c mem PCI: 00:02.1 10 <- [0x00f624a000 - 0x00f624a0ff] size 0x00000100 gran 0x08 mem PCI: 00:04.0 20 <- [0x0000003cc0 - 0x0000003ccf] size 0x00000010 gran 0x04 io PCI: 00:05.0 10 <- [0x0000004000 - 0x0000004007] size 0x00000008 gran 0x03 io PCI: 00:05.0 14 <- [0x0000004070 - 0x0000004073] size 0x00000004 gran 0x02 io PCI: 00:05.0 18 <- [0x0000004010 - 0x0000004017] size 0x00000008 gran 0x03 io PCI: 00:05.0 1c <- [0x0000004080 - 0x0000004083] size 0x00000004 gran 0x02 io PCI: 00:05.0 20 <- [0x0000003cd0 - 0x0000003cdf] size 0x00000010 gran 0x04 io PCI: 00:05.0 24 <- [0x00f6246000 - 0x00f6246fff] size 0x00001000 gran 0x0c mem PCI: 00:05.1 10 <- [0x0000004020 - 0x0000004027] size 0x00000008 gran 0x03 io PCI: 00:05.1 14 <- [0x0000004090 - 0x0000004093] size 0x00000004 gran 0x02 io PCI: 00:05.1 18 <- [0x0000004030 - 0x0000004037] size 0x00000008 gran 0x03 io PCI: 00:05.1 1c <- [0x00000040a0 - 0x00000040a3] size 0x00000004 gran 0x02 io PCI: 00:05.1 20 <- [0x0000003ce0 - 0x0000003cef] size 0x00000010 gran 0x04 io PCI: 00:05.1 24 <- [0x00f6247000 - 0x00f6247fff] size 0x00001000 gran 0x0c mem PCI: 00:05.2 10 <- [0x0000004040 - 0x0000004047] size 0x00000008 gran 0x03 io PCI: 00:05.2 14 <- [0x00000040b0 - 0x00000040b3] size 0x00000004 gran 0x02 io PCI: 00:05.2 18 <- [0x0000004050 - 0x0000004057] size 0x00000008 gran 0x03 io PCI: 00:05.2 1c <- [0x00000040c0 - 0x00000040c3] size 0x00000004 gran 0x02 io PCI: 00:05.2 20 <- [0x0000003cf0 - 0x0000003cff] size 0x00000010 gran 0x04 io PCI: 00:05.2 24 <- [0x00f6248000 - 0x00f6248fff] size 0x00001000 gran 0x0c mem PCI: 00:06.0 1c <- [0x0000001000 - 0x0000001fff] size 0x00001000 gran 0x0c bus 01 io PCI: 00:06.0 20 <- [0x00f6100000 - 0x00f61fffff] size 0x00100000 gran 0x14 bus 01 mem PCI: 01:07.0 10 <- [0x0000001000 - 0x000000101f] size 0x00000020 gran 0x05 io PCI: 01:07.1 10 <- [0x0000001020 - 0x0000001027] size 0x00000008 gran 0x03 io PCI: 01:0a.0 10 <- [0x00f6104000 - 0x00f61047ff] size 0x00000800 gran 0x0b mem PCI: 01:0a.0 14 <- [0x00f6100000 - 0x00f6103fff] size 0x00004000 gran 0x0e mem PCI: 00:06.1 10 <- [0x00f6240000 - 0x00f6243fff] size 0x00004000 gran 0x0e mem PCI: 00:08.0 10 <- [0x00f6249000 - 0x00f6249fff] size 0x00001000 gran 0x0c mem PCI: 00:08.0 14 <- [0x0000004060 - 0x0000004067] size 0x00000008 gran 0x03 io PCI: 00:08.0 18 <- [0x00f624b000 - 0x00f624b0ff] size 0x00000100 gran 0x08 mem PCI: 00:08.0 1c <- [0x00f624c000 - 0x00f624c00f] size 0x00000010 gran 0x04 mem PCI: 00:0f.0 1c <- [0x0000002000 - 0x0000002fff] size 0x00001000 gran 0x0c bus 07 io PCI: 00:0f.0 24 <- [0x00e0000000 - 0x00efffffff] size 0x10000000 gran 0x14 bus 07 prefmem PCI: 00:0f.0 20 <- [0x00f4000000 - 0x00f60fffff] size 0x02100000 gran 0x14 bus 07 mem PCI: 07:00.0 10 <- [0x00f4000000 - 0x00f4ffffff] size 0x01000000 gran 0x18 mem PCI: 07:00.0 14 <- [0x00e0000000 - 0x00efffffff] size 0x10000000 gran 0x1c prefmem64 PCI: 07:00.0 1c <- [0x00f5000000 - 0x00f5ffffff] size 0x01000000 gran 0x18 mem64 PCI: 07:00.0 24 <- [0x0000002000 - 0x000000207f] size 0x00000080 gran 0x07 io PCI: 07:00.0 30 <- [0x00f6000000 - 0x00f601ffff] size 0x00020000 gran 0x11 romem PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] size 0x04000000 gran 0x1a mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 00 PCI: 00:00.0 subsystem <- 1022/2b80 PCI: 00:00.0 cmd <- 06 PCI: 00:01.0 subsystem <- 1022/2b80 PCI: 00:01.0 cmd <- 0f mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297 mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237 mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060 mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064 PNP: 002e.7 missing enable_resources PCI: 00:01.1 subsystem <- 1022/2b80 PCI: 00:01.1 cmd <- 01 PCI: 00:01.2 cmd <- 400 PCI: 00:01.3 cmd <- 02 PCI: 00:02.0 subsystem <- 1022/2b80 PCI: 00:02.0 cmd <- 02 PCI: 00:02.1 subsystem <- 1022/2b80 PCI: 00:02.1 cmd <- 02 PCI: 00:04.0 subsystem <- 1022/2b80 PCI: 00:04.0 cmd <- 01 PCI: 00:05.0 subsystem <- 1022/2b80 PCI: 00:05.0 cmd <- 03 PCI: 00:05.1 subsystem <- 1022/2b80 PCI: 00:05.1 cmd <- 03 PCI: 00:05.2 subsystem <- 1022/2b80 PCI: 00:05.2 cmd <- 03 PCI: 00:06.0 bridge ctrl <- 0a03 PCI: 00:06.0 cmd <- 107 PCI: 01:07.0 cmd <- 01 PCI: 01:07.1 cmd <- 01 PCI: 01:0a.0 cmd <- 02 PCI: 00:06.1 subsystem <- 1022/2b80 PCI: 00:06.1 cmd <- 02 PCI: 00:08.0 subsystem <- 1022/2b80 PCI: 00:08.0 cmd <- 03 PCI: 00:0a.0 bridge ctrl <- 0003 PCI: 00:0a.0 cmd <- 00 PCI: 00:0b.0 bridge ctrl <- 0003 PCI: 00:0b.0 cmd <- 00 PCI: 00:0c.0 bridge ctrl <- 0003 PCI: 00:0c.0 cmd <- 00 PCI: 00:0d.0 bridge ctrl <- 0003 PCI: 00:0d.0 cmd <- 00 PCI: 00:0e.0 bridge ctrl <- 0003 PCI: 00:0e.0 cmd <- 00 PCI: 00:0f.0 bridge ctrl <- 000b PCI: 00:0f.0 cmd <- 07 PCI: 07:00.0 cmd <- 03 PCI: 00:18.1 subsystem <- 1022/2b80 PCI: 00:18.1 cmd <- 00 PCI: 00:18.2 subsystem <- 1022/2b80 PCI: 00:18.2 cmd <- 00 PCI: 00:18.3 cmd <- 00 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b Initializing CPU #0 CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x00 done. ECC Disabled CPU #0 Initialized Initializing CPU #1 Waiting for 1 CPUS to stop CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x01 done. CPU #1 Initialized All AP CPUs stopped PCI: 00:18.0 init PCI: 00:01.0 init set power on after power fail RTC Init RTC: Checksum invalid zeroing cmos Invalid CMOS LB checksum PNP: 002e.1 init PNP: 002e.4 init FAN_CTL: reg = 0x02a9, read value = 0x50 FAN_CTL: reg = 0x02a9, writing value = 0xd7 PNP: 002e.5 init Keyboard init... PNP: 002e.6 init PCI: 00:01.1 init PCI: 00:02.1 init PCI: 00:04.0 init IDE0 PCI: 00:05.0 init SATA S SATA P PCI: 00:05.1 init SATA S SATA P PCI: 00:05.2 init SATA S SATA P PCI: 00:06.0 init dev_root mem base = 0x00e0000000 [0x50] <-- 0xe0000000 PCI: 00:06.1 init base = f6240000 codec_mask = 01 codec viddid: 10ec0883 No verb! PCI: 00:08.0 init MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1 PCI: 00:0a.0 init PCI: 00:0b.0 init PCI: 00:0c.0 init PCI: 00:0d.0 init PCI: 00:0e.0 init PCI: 00:0f.0 init PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. PCI: 00:01.2 init PCI: 00:01.3 init PCI: 01:07.0 init PCI: 01:07.1 init PCI: 01:0a.0 init PCI: 07:00.0 init rom address for PCI: 07:00.0 = f6000000 copying VGA ROM Image from 0xf6000000 to 0xc0000, 0xf600 bytes entering emulator halt_sys: file /home/andi/freeBIOS/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 Devices initialized Writing IRQ routing tables to 0xf0000...done. Wrote the mp table end at: 00000020 - 00000274 Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0400 to 0x00100000 Wrote linuxbios table at: 00000530 - 00000e20 checksum 9ef5
Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x3dd80 offset 0xc0 filesize 0x13d68 (cleaned up) New segment addr 0x100000 size 0x3dd80 offset 0xc0 filesize 0x13d68 New segment addr 0x13dd80 size 0x48 offset 0x13e40 filesize 0x48 (cleaned up) New segment addr 0x13dd80 size 0x48 offset 0x13e40 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x00000000bff80000 memsz: 0x000000000003dd80 filesz: 0x0000000000013d68 Clearing Segment: addr: 0x00000000bff93d68 memsz: 0x000000000002a018 Loading Segment: addr: 0x00000000bffbdd80 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x10ef9c FILO version 0.5 (andi@flashgordon) Sun Jun 24 11:47:31 CEST 2007 setup_timers: CPU 2400 MHz menu: hde5:/grub/menu.lst find_ide_controller: found PCI IDE controller 10de:037f prog_if=0x85 find_ide_controller: primary channel: native PCI mode find_ide_controller: cmd_base=0x4000 ctrl_base=0x4070 ide_software_reset: Waiting for ide2 to become ready for reset... ok init_drive: Testing for hde init_drive: Probing for hde init_drive: LBA mode, sectors=268435455 init_drive: LBA48 mode, sectors=488395055 init_drive: Init device params... ok hde: LBA48 250GB: SAMSUNG SP2504C init_drive: Testing for hdf init_drive: Probing for hdf print_status: IDE: status=0x0, err=0x0 init_drive: Testing for hdf init_drive: Probing for hdf print_status: IDE: status=0x0, err=0x0 open_pc_partition: Extended partition at 4 open_pc_partition: cur_part=4 at 132825420 devopen: Partition 5 start 132825483 length 2040192 Mounted ext2fs find_ide_controller: found PCI IDE controller 10de:036e prog_if=0x8a find_ide_controller: primary channel: compatibility mode find_ide_controller: cmd_base=0x1f0 ctrl_base=0x3f4 ide_software_reset: Waiting for ide0 to become ready for reset... ok init_drive: Testing for hda init_drive: Probing for hda print_status: IDE: status=0x51, err=0x4 init_drive: Testing for hda init_drive: Probing for hda hda: ATAPI: Optiarc DVD RW AD-7173A pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x64 atapi_request_sense: 70 00 06 00 00 00 00 0a 00 00 00 00 29 00 00 00 00 00 pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 46 d3 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 46 d3 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 47 ae atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 47 ae atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 47 ae atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 48 88 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 48 88 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 48 88 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 49 62 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 49 62 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide pio_packet: no drq after sending packet print_status: IDE: status=0x51, err=0x24 atapi_request_sense: 70 00 02 00 00 00 00 0a 00 00 00 00 3a 00 00 80 49 62 atapi_detect_medium: Device reports MEDIUM NOT PRESENT Media detection failed devopen: failed to open ide devopen: already open Mounted ext2fs devopen: already open Found Linux version 2.6.21 (root@flashgordon) #4 SMP Sun Jun 24 21:35:21 CEST 2007 bzImage. Loading kernel... ok Jumping to entry point...