Actually that is because of Andi's patch cause the problem.
I was wondering why we can not use these ram.
It is good if update kernel instead.
YH
-----Original Message----- From: linuxbios-bounces@linuxbios.org [mailto:linuxbios-bounces@linuxbios.org] On Behalf Of Roman Kononov Sent: Wednesday, January 31, 2007 2:37 PM To: LinuxBIOS Subject: [LinuxBIOS] [PATCH] e820 table correction
Hello,
I have this situation:
Linuxbios boots an Opteron motherboard with 1GB memory.
Linuxbios directly loads a recent linux kernel. The memory layout is like this:
BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000000e18 (reserved) BIOS-e820: 0000000000000e18 - 00000000000a0000 (usable) BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) BIOS-e820: 00000000000f0000 - 00000000000f0400 (reserved) BIOS-e820: 00000000000f0400 - 0000000040000000 (usable)
The f0000-f0400 region contains IRQ and ACPI tables.
At some point the kernel builds a resource table containing all physical address ranges and type of hardware the addresses are mapped to. The table is accessible via /proc/iomem:
# cat /proc/iomem 00000000-00000e17 : reserved 00000e18-0009ffff : System RAM 000a0000-000bffff : Video RAM area 000c0000-000cbfff : Video ROM 000f0000-000fffff : System ROM e0000000-efffffff : PCI Bus #03 e0000000-efffffff : 0000:03:00.0 f0000000-f3ffffff : GART f4000000-f60fffff : PCI Bus #03 f4000000-f4ffffff : 0000:03:00.0 f5000000-f5ffffff : 0000:03:00.0 f6000000-f601ffff : 0000:03:00.0 f6100000-f6100fff : 0000:00:01.0 f6101000-f6101fff : 0000:00:02.0 f6101000-f6101fff : ohci_hcd f6102000-f6102fff : 0000:00:04.0 f6103000-f6103fff : 0000:00:07.0 f6103000-f6103fff : sata_nv f6104000-f6104fff : 0000:00:08.0 f6104000-f6104fff : sata_nv f6105000-f6105fff : 0000:00:0a.0 f6106000-f61060ff : 0000:00:02.1 f6200000-f620ffff : 0000:40:01.0
As you can see, the 00000000000f0400-0000000040000000 region is not listed.
It is not listed because the kernel unconditionally adds "000f0000-000fffff : System ROM" first (look for "request_resource(&iomem_resource, &system_rom_resource)"), and then the attempt to add f0400-40000000 range fails because of overlapping.
The kernel does not care that the range is not listed there. Kexec does. It uses the /proc/iomem file to instruct the kexec system call how to place the segments of a new kernel in the physical memory. Kexec fails to start a new kernel because it cannot locate enough physical memory.
This must be fixed either in linux or linuxbios.
Assuming that linuxbios is to be fixed, I cooked a patch which provides this memory layout:
BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000000e18 (reserved) BIOS-e820: 0000000000000e18 - 00000000000a0000 (usable) BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000040000000 (usable)
The /proc/iomem contains:
# cat /proc/iomem 00000000-00000e17 : reserved 00000e18-0009ffff : System RAM 000a0000-000bffff : Video RAM area 000c0000-000cbfff : Video ROM 000f0000-000fffff : System ROM 00100000-3fffffff : System RAM 00100000-00203c61 : Kernel code 00203c62-00248c3f : Kernel data e0000000-efffffff : PCI Bus #03 e0000000-efffffff : 0000:03:00.0 f0000000-f3ffffff : GART f4000000-f60fffff : PCI Bus #03 f4000000-f4ffffff : 0000:03:00.0 f5000000-f5ffffff : 0000:03:00.0 f6000000-f601ffff : 0000:03:00.0 f6100000-f6100fff : 0000:00:01.0 f6101000-f6101fff : 0000:00:02.0 f6101000-f6101fff : ohci_hcd f6102000-f6102fff : 0000:00:04.0 f6103000-f6103fff : 0000:00:07.0 f6103000-f6103fff : sata_nv f6104000-f6104fff : 0000:00:08.0 f6104000-f6104fff : sata_nv f6105000-f6105fff : 0000:00:0a.0 f6106000-f61060ff : 0000:00:02.1 f6200000-f620ffff : 0000:40:01.0
Kexec is happier with the patch.
Regards,
Signed-off-by: Roman Kononov kononov195-lbl@yahoo.com ---