Author: stepan Date: 2008-10-29 05:46:52 +0100 (Wed, 29 Oct 2008) New Revision: 3701
Added: trunk/coreboot-v2/src/include/cpu/x86/smm.h trunk/coreboot-v2/src/southbridge/intel/i82801gx/ trunk/coreboot-v2/src/southbridge/intel/i82801gx/Config.lb trunk/coreboot-v2/src/southbridge/intel/i82801gx/IOMAP trunk/coreboot-v2/src/southbridge/intel/i82801gx/chip.h trunk/coreboot-v2/src/southbridge/intel/i82801gx/cmos_failover.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_early_smbus.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ide.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nic.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pcie.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_reset.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.h trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_watchdog.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/smihandler.c trunk/coreboot-v2/src/southbridge/intel/i82801gx/smm.ld trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmhandler.S trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmrelocate.S Modified: trunk/coreboot-v2/src/config/Options.lb trunk/coreboot-v2/src/include/device/device.h Log: Support for the Intel ICH7 southbridge.
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer stepan@coresystems.de Acked-by: Ronald G. Minnich rminnich@gmail.com
Modified: trunk/coreboot-v2/src/config/Options.lb =================================================================== --- trunk/coreboot-v2/src/config/Options.lb 2008-10-29 04:45:28 UTC (rev 3700) +++ trunk/coreboot-v2/src/config/Options.lb 2008-10-29 04:46:52 UTC (rev 3701) @@ -856,6 +856,11 @@ export used comment "Have hard reset" end +define HAVE_SMI_HANDLER + default none + export used + comment "Set, if the board needs an SMI handler" +end define MEMORY_HOLE default none export used
Added: trunk/coreboot-v2/src/include/cpu/x86/smm.h =================================================================== --- trunk/coreboot-v2/src/include/cpu/x86/smm.h (rev 0) +++ trunk/coreboot-v2/src/include/cpu/x86/smm.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,253 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + + +typedef uint64_t u64; + +/* AMD64 SMM State-Save Area + * starts @ 0x7e00 + */ +typedef struct { + u16 es_selector; + u16 es_attributes; + u32 es_limit; + u64 es_base; + + u16 cs_selector; + u16 cs_attributcs; + u32 cs_limit; + u64 cs_base; + + u16 ss_selector; + u16 ss_attributss; + u32 ss_limit; + u64 ss_base; + + u16 ds_selector; + u16 ds_attributds; + u32 ds_limit; + u64 ds_base; + + u16 fs_selector; + u16 fs_attributfs; + u32 fs_limit; + u64 fs_base; + + u16 gs_selector; + u16 gs_attributgs; + u32 gs_limit; + u64 gs_base; + + u8 reserved0[4]; + u16 gdtr_limit; + u8 reserved1[2]; + u64 gdtr_base; + + u16 ldtr_selector; + u16 ldtr_attributes; + u32 ldtr_limit; + u64 ldtr_base; + + u8 reserved2[4]; + u16 idtr_limit; + u8 reserved3[2]; + u64 idtr_base; + + u16 tr_selector; + u16 tr_attributes; + u32 tr_limit; + u64 tr_base; + + u8 reserved4[40]; + + u8 io_restart; + u8 autohalt_restart; + + u8 reserved5[6]; + + u64 efer; + + u8 reserved6[36]; + + u32 smm_revision; + u32 smbase; + + u8 reserved7[68]; + + u64 cr4; + u64 cr3; + u64 cr0; + u64 dr7; + u64 dr6; + + u64 rflags; + u64 rip; + u64 r15; + u64 r14; + u64 r13; + u64 r12; + u64 r11; + u64 r10; + u64 r9; + u64 r8; + + u64 rdi; + u64 rsi; + u64 rpb; + u64 rsp; + u64 rbx; + u64 rdx; + u64 rcx; + u64 rax; +} __attribute__((packed)) amd64_smm_state_save_area_t; + + +/* Intel Core 2 (EM64T) SMM State-Save Area + * starts @ 0x7d00 + */ +typedef struct { + u8 reserved0[208]; + + u32 gdtr_upper_base; + u32 ldtr_upper_base; + u32 idtr_upper_base; + + u8 reserved1[4]; + + u64 io_rdi; + u64 io_rip; + u64 io_rcx; + u64 io_rsi; + u64 cr4; + + u8 reserved2[68]; + + u64 gdtr_base; + u64 idtr_base; + u64 ldtr_base; + + u8 reserved3[84]; + + u32 smm_revision; + u32 smbase; + + u16 io_restart; + u16 autohalt_restart; + + u8 reserved4[24]; + + u64 r15; + u64 r14; + u64 r13; + u64 r12; + u64 r11; + u64 r10; + u64 r9; + u64 r8; + + u64 rax; + u64 rcx; + u64 rdx; + u64 rbx; + + u64 rsp; + u64 rbp; + u64 rsi; + u64 rdi; + + + u64 io_mem_addr; + u32 io_misc_info; + + u32 es_sel; + u32 cs_sel; + u32 ss_sel; + u32 ds_sel; + u32 fs_sel; + u32 gs_sel; + + u32 ldtr_sel; + u32 tr_sel; + + u64 dr7; + u64 dr6; + u64 rip; + u64 efer; + u64 rflags; + + u64 cr3; + u64 cr0; +} __attribute__((packed)) em64t_smm_state_save_area_t; + + +/* Legacy x86 SMM State-Save Area + * starts @ 0x7e00 + */ + +typedef struct { + u8 reserved0[248]; + u32 smbase; + u32 smm_revision; + u16 io_restart; + u16 autohalt_restart; + u8 reserved1[132]; + u32 gdtbase; + u8 reserved2[8]; + u32 idtbase; + u8 reserved3[16]; + u32 es; + u32 cs; + u32 ss; + u32 ds; + u32 fs; + u32 gs; + u32 ldtbase; + u32 tr; + u32 dr7; + u32 dr6; + u32 eax; + u32 ecx; + u32 edx; + u32 ebx; + u32 esp; + u32 ebp; + u32 esi; + u32 edi; + u32 eip; + u32 eflags; + u32 cr3; + u32 cr0; +} __attribute__((packed)) legacy_smm_state_save_area_t; + +typedef enum { + AMD64, + EM64T, + LEGACY +} save_state_type_t; + + +typedef struct { + save_state_type_t type; + union { + amd64_smm_state_save_area_t *amd64_state_save; + em64t_smm_state_save_area_t *em64t_state_save; + legacy_smm_state_save_area_t *legacy_state_save; + }; +} smm_state_save_area_t; +
Modified: trunk/coreboot-v2/src/include/device/device.h =================================================================== --- trunk/coreboot-v2/src/include/device/device.h 2008-10-29 04:45:28 UTC (rev 3700) +++ trunk/coreboot-v2/src/include/device/device.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -71,7 +71,7 @@ struct device_path path; unsigned vendor; unsigned device; - unsigned int class; /* 3 bytes: (base,sub,prog-if) */ + unsigned int class; /* 3 bytes: (base, sub, prog-if) */ unsigned int hdr_type; /* PCI header type */ unsigned int enabled : 1; /* set if we should enable the device */ unsigned int initialized : 1; /* set if we have initialized the device */ @@ -85,7 +85,7 @@ struct resource resource[MAX_RESOURCES]; unsigned int resources;
- /* link are (down sream) buses attached to the device, usually a leaf + /* link are (down stream) buses attached to the device, usually a leaf * device with no children have 0 buses attached and a bridge has 1 bus */ struct bus link[MAX_LINKS];
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/Config.lb =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/Config.lb (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/Config.lb 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,66 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 coresystems GmbH +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +config chip.h +driver i82801gx.o +driver i82801gx_ac97.o +driver i82801gx_ide.o +driver i82801gx_lpc.o +driver i82801gx_nic.o +driver i82801gx_pci.o +driver i82801gx_pcie.o +driver i82801gx_sata.o +driver i82801gx_usb.o +driver i82801gx_usb_ehci.o + +object i82801gx_reset.o +object i82801gx_watchdog.o + +object i82801gx_smi.o +object smmrelocate.S + +makerule smmhandler.o + depends "$(TOP)/src/southbridge/intel/i82801gx/smmhandler.S" + action "@$(CC) -c $(CPU_OPT) $(CPPFLAGS) $(CFLAGS) -o $@ $<" +end + +makerule smihandler.o + depends "$(TOP)/src/southbridge/intel/i82801gx/smihandler.c" + action "@$(CC) -c $(CPU_OPT) $(CPPFLAGS) $(CFLAGS) -o $@ $<" +end + +makerule smm.o + depends "smmhandler.o smihandler.o printk.o vtxprintf.o $(LIBGCC_FILE_NAME)" + action "$(CC) $(DISTRO_LFLAGS) -nostdlib -r -o $@ smmhandler.o smihandler.o printk.o vtxprintf.o $(LIBGCC_FILE_NAME)" +end + +makerule smm + depends "smm.o $(TOP)/src/southbridge/intel/i82801gx/smm.ld ldoptions" + action "$(CC) $(DISTRO_LFLAGS) -nostdlib -nostartfiles -static -o smm.elf -T $(TOP)/src/southbridge/intel/i82801gx/smm.ld smm.o" + action "$(CROSS_COMPILE)nm -n smm.elf | sort > smm.map" + action "$(OBJCOPY) -O binary smm.elf smm" +end + +makerule smm_bin.c + depends "smm" + action "(echo 'unsigned char smm[] = {'; od -vtx1 smm | sed -e 's,^[0-9]* *,,' -e 's:[0-9a-f][0-9a-f] :0x&,:g' -e 's:[0-9a-f][0-9a-f]$$:0x&,:'; echo '}; unsigned int smm_len = '; wc -c smm |awk '{print $$1;}' ; echo ';') > smm_bin.c" +end + +object ./smm_bin.o
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/IOMAP =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/IOMAP (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/IOMAP 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,35 @@ +Non-automatic IO-Addresses +-------------------------- + +The following dynamic IO BARs are used on the ICH7 for the Kontron Default BIOS: + +GPIOBASE 0x480 (64 bytes) +PMBASE 0x800 (128 bytes) +SMBASE 0x400 (32 bytes) +HWMON 0xa00 (??) + +The following dynamic IO BARs are used on the ICH7 for the Getac Default BIOS: + +GPIOBASE 0x1180 (64 bytes) +PMBASE 0x1000 (128 bytes) +SMBASE 0x18e0 (32 bytes) + +The Getac also needs an IO Trapped area of 0x0C bytes (defaults to 0x800) + +coreboot: +GPIOBASE 0x480 (64 bytes) +PMBASE 0x500 (128 bytes) +SMBASE 0x400 (32 bytes) +HWMON 0xa00 (??) + + + +NOTE: Coreboot sets the SMBASE to 0xf00 in auto.c. But it gets relocated +in stage2 because its a "normal BAR" (to 0x2080 in one case here). + +This is not unhealthy but at least confusing. We should provide a method to +nail down certain resources for stage2. + +For a list of static I/O space allocation look at 6.3.1 of the ICH7 Family +Datasheet. +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/chip.h =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/chip.h (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/chip.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,33 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef SOUTHBRIDGE_INTEL_I82801GX_CHIP_H +#define SOUTHBRIDGE_INTEL_I82801GX_CHIP_H + +struct southbridge_intel_i82801gx_config { + uint32_t ide_legacy_combined; + uint32_t ide_enable_primary; + uint32_t ide_enable_secondary; + uint32_t sata_ahci; +}; + +extern struct chip_operations southbridge_intel_i82801gx_ops; + +#endif /* SOUTHBRIDGE_INTEL_I82801GX_CHIP_H */
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/cmos_failover.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/cmos_failover.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/cmos_failover.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,35 @@ +/* + * This file is part of the coreboot project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include "i82801gx.h" + +#define RTC_FAILED (1 <<2) +#define GEN_PMCON_3 0xa4 + +static void check_cmos_failed(void) +{ + u8 byte; + byte = pci_read_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3); + if (byte & RTC_FAILED) { + // clear bit 1 and bit 2 + byte = cmos_read(RTC_BOOT_BYTE); + byte &= 0x0c; + byte |= MAX_REBOOT_CNT << 4; + cmos_write(byte, RTC_BOOT_BYTE); + } +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,34 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include "i82801gx.h" + +void i82801gx_enable(device_t dev) +{ + +} + +struct chip_operations southbridge_intel_i82801gx_ops = { + CHIP_NAME("Intel ICH7/ICH7-M (82801Gx) Series Southbridge") + .enable_dev = i82801gx_enable, +};
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,122 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H +#define SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H + +#include "chip.h" +extern void i82801gx_enable(device_t dev); + +#define PCI_DMA_CFG 0x90 +#define SERIRQ_CNTL 0x64 +#define GEN_CNTL 0xd0 +#define GEN_STS 0xd4 +#define RTC_CONF 0xd8 +#define GEN_PMCON_1 0xa0 +#define GEN_PMCON_2 0xa2 +#define GEN_PMCON_3 0xa4 + +#define PMBASE 0x40 +#define ACPI_CNTL 0x44 +#define BIOS_CNTL 0x4E +#define GPIO_BASE 0x48 /* LPC GPIO Base Address Register */ +#define GPIO_CNTL 0x4C /* LPC GPIO Control Register */ + +#define PIRQA_ROUT 0x60 +#define PIRQB_ROUT 0x61 +#define PIRQC_ROUT 0x62 +#define PIRQD_ROUT 0x63 +#define PIRQE_ROUT 0x68 +#define PIRQF_ROUT 0x69 +#define PIRQG_ROUT 0x6A +#define PIRQH_ROUT 0x6B + +#define FUNC_DIS 0xF2 + +#define LPC_IO_DEC 0x80 /* IO Decode Ranges Register */ +#define LPC_EN 0x82 /* LPC IF Enables Register */ + +#define SBUS_NUM 0x19 +#define SUB_BUS_NUM 0x1A +#define SMLT 0x1B +#define IOBASE 0x1C +#define IOLIM 0x1D +#define MEMBASE 0x20 +#define MEMLIM 0x22 +#define CNF 0x50 +#define MTT 0x70 +#define PCI_MAST_STS 0x82 + +/* GEN_PMCON_3 bits */ +#define RTC_BATTERY_DEAD (1 << 2) +#define RTC_POWER_FAILED (1 << 1) +#define SLEEP_AFTER_POWER_FAIL (1 << 0) + +/* PCI Configuration Space (D31:F1) */ +#define INTR_LN 0x3c +#define IDE_TIM_PRI 0x40 /* IDE timings, primary */ +#define IDE_DECODE_ENABLE (1 << 15) +#define IDE_SITRE (1 << 14) +#define IDE_TIM_SEC 0x42 /* IDE timings, secondary */ +#define IDE_CONFIG 0x54 /* IDE I/O Configuration Register */ +#define SIG_MODE_NORMAL (0 << 16) +#define SIG_MODE_TRISTATE (1 << 16) +#define SIG_MODE_DRIVELOW (2 << 16) +#define FAST_PCB1 (1 << 13) +#define FAST_PCB0 (1 << 12) +#define PCB1 (1 << 1) +#define PCB0 (1 << 0) + +/* PCI Configuration Space (D31:F3) */ +#define SMB_BASE 0x20 +#define HOSTC 0x40 + +/* HOSTC bits */ +#define I2C_EN (1 << 2) +#define SMB_SMI_EN (1 << 1) +#define HST_EN (1 << 0) + +/* SMBus I/O bits. + * TODO: It does not matter where we put the SMBus IO base, as long as we keep + * consistent and don't interfere with other devices. Stage2 will relocate + * this anyways. But it's a general problem we have not solved in the brightest + * possible way. + */ +/* #define SMBUS_IO_BASE 0x1000 */ +#define SMBUS_IO_BASE 0x0400 + +#define SMBHSTSTAT 0x0 +#define SMBHSTCTL 0x2 +#define SMBHSTCMD 0x3 +#define SMBXMITADD 0x4 +#define SMBHSTDAT0 0x5 +#define SMBHSTDAT1 0x6 +#define SMBBLKDAT 0x7 +#define SMBTRNSADD 0x9 +#define SMBSLVDATA 0xa +#define SMLINK_PIN_CTL 0xe +#define SMBUS_PIN_CTL 0xf + +#define SMBUS_TIMEOUT (10 * 1000 * 100) + +/* HPET, if present */ +#define HPET_ADDR 0xfed0000 + +#endif /* SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H */
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,71 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "i82801gx.h" + +static void ac97_audio_init(struct device *dev) +{ + // XXX init AC97 codecs. +} + +static void ac97_modem_init(struct device *dev) +{ + // XXX init modem? +} + +static struct device_operations ac97_audio_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = ac97_audio_init, + .scan_bus = 0, + .enable = i82801gx_enable, +}; + +static struct device_operations ac97_modem_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = ac97_modem_init, + .scan_bus = 0, + .enable = i82801gx_enable, +}; + + + +/* 82801GB/GR/GDH/GBM/GHM (ICH7/ICH7R/ICH7DH/ICH7-M/ICH7-M DH) */ +/* Note: 82801GU (ICH7-U) doesn't have AC97 audio/modem. */ + +static const struct pci_driver i82801gb_ac97_audio __pci_driver = { + .ops = &ac97_audio_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_AC97_AUDIO, +}; + +static const struct pci_driver i82801gb_ac97_modem __pci_driver = { + .ops = &ac97_modem_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_AC97_MODEM, +}; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_early_smbus.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_early_smbus.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_early_smbus.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,59 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <device/pci_ids.h> +#include "i82801gx.h" +#include "i82801gx_smbus.h" + +static void enable_smbus(void) +{ + device_t dev; + + /* Set the SMBus device statically. */ + dev = PCI_DEV(0x0, 0x1f, 0x3); + + /* Check to make sure we've got the right device. */ + if (pci_read_config16(dev, 0x2) != 0x27da) { + die("SMBus controller not found!"); + } + + /* Set SMBus I/O base. */ + pci_write_config32(dev, SMB_BASE, + SMBUS_IO_BASE | PCI_BASE_ADDRESS_SPACE_IO); + + /* Set SMBus enable. */ + pci_write_config8(dev, HOSTC, HST_EN); + + /* Set SMBus I/O space enable. */ + pci_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO); + + /* Disable interrupt generation. */ + outb(0, SMBUS_IO_BASE + SMBHSTCTL); + + /* Clear any lingering errors, so transactions can run. */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + print_debug("SMBus controller enabled.\r\n"); +} + +static inline int smbus_read_byte(unsigned device, unsigned address) +{ + return do_smbus_read_byte(device, address); +} +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ide.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ide.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ide.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,100 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "i82801gx.h" + +typedef struct southbridge_intel_i82801gx_config config_t; + +static void ide_init(struct device *dev) +{ + u16 ideTimingConfig; + u32 reg32; + + /* Get the chip configuration */ + config_t *config = dev->chip_info; + + int enable_primary = config->ide_enable_primary; + int enable_secondary = config->ide_enable_secondary; + + reg32 = pci_read_config32(dev, PCI_COMMAND); + pci_write_config32(dev, PCI_COMMAND, reg32 | PCI_COMMAND_IO | PCI_COMMAND_MASTER); + + /* Native Capable, but not enabled. */ + pci_write_config8(dev, 0x09, 0x8a); + + ideTimingConfig = pci_read_config16(dev, IDE_TIM_PRI); + ideTimingConfig &= ~IDE_DECODE_ENABLE; + ideTimingConfig |= IDE_SITRE; + if (enable_primary) { + /* Enable primary IDE interface. */ + ideTimingConfig |= IDE_DECODE_ENABLE; + ideTimingConfig |= (2 << 12); // ISP = 3 clocks + ideTimingConfig |= (3 << 8); // RCT = 1 clock + ideTimingConfig |= (1 << 1); // IE0 + ideTimingConfig |= (1 << 0); // TIME0 + printk_debug("IDE0 "); + } + pci_write_config16(dev, IDE_TIM_PRI, ideTimingConfig); + + ideTimingConfig = pci_read_config16(dev, IDE_TIM_SEC); + ideTimingConfig &= ~IDE_DECODE_ENABLE; + ideTimingConfig |= IDE_SITRE; + if (enable_secondary) { + /* Enable secondary IDE interface. */ + ideTimingConfig |= IDE_DECODE_ENABLE; + ideTimingConfig |= (2 << 12); // ISP = 3 clocks + ideTimingConfig |= (3 << 8); // RCT = 1 clock + ideTimingConfig |= (1 << 1); // IE0 + ideTimingConfig |= (1 << 0); // TIME0 + printk_debug("IDE1 "); + } + pci_write_config16(dev, IDE_TIM_SEC, ideTimingConfig); + + /* Set IDE I/O Configuration */ + if (enable_secondary) + reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + else + reg32 = SIG_MODE_NORMAL | FAST_PCB1 | PCB1; + pci_write_config32(dev, IDE_CONFIG, reg32); + + /* Set Interrupt Line */ + /* Interrupt Pin is set by D31IP.PIP */ + pci_write_config32(dev, INTR_LN, 0xff); /* Int 15 */ +} + +static struct device_operations ide_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = ide_init, + .scan_bus = 0, + .enable = i82801gx_enable, +}; + +/* 82801Gx */ +static const struct pci_driver i82801gx_ide __pci_driver = { + .ops = &ide_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27df, +};
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,361 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <pc80/mc146818rtc.h> +#include <pc80/isa-dma.h> +#include <arch/io.h> +#include "i82801gx.h" + +#include "../../../northbridge/intel/i945/ich7.h" + +#define MAINBOARD_POWER_OFF 0 +#define MAINBOARD_POWER_ON 1 + +#ifndef MAINBOARD_POWER_ON_AFTER_FAIL +#define MAINBOARD_POWER_ON_AFTER_FAIL MAINBOARD_POWER_ON +#endif + +#define NMI_OFF 0 + +/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control + * 0x00 - 0000 = Reserved + * 0x01 - 0001 = Reserved + * 0x02 - 0010 = Reserved + * 0x03 - 0011 = IRQ3 + * 0x04 - 0100 = IRQ4 + * 0x05 - 0101 = IRQ5 + * 0x06 - 0110 = IRQ6 + * 0x07 - 0111 = IRQ7 + * 0x08 - 1000 = Reserved + * 0x09 - 1001 = IRQ9 + * 0x0A - 1010 = IRQ10 + * 0x0B - 1011 = IRQ11 + * 0x0C - 1100 = IRQ12 + * 0x0D - 1101 = Reserved + * 0x0E - 1110 = IRQ14 + * 0x0F - 1111 = IRQ15 + * PIRQ[n]_ROUT[7] - PIRQ Routing Control + * 0x80 - The PIRQ is not routed. + */ + +#define PIRQA 0x03 +#define PIRQB 0x05 +#define PIRQC 0x06 +#define PIRQD 0x07 +#define PIRQE 0x09 +#define PIRQF 0x0A +#define PIRQG 0x0B +#define PIRQH 0x0C + +static void i82801gx_enable_apic(struct device *dev) +{ + int i; + u32 reg32; + volatile u32 *ioapic_index = (volatile u32 *)0xfec00000; + volatile u32 *ioapic_data = (volatile u32 *)0xfec00010; + + /* Enable ACPI I/O and power management. */ + pci_write_config8(dev, ACPI_CNTL, 0x80); + + *ioapic_index = 0; + *ioapic_data = (1 << 25); + + *ioapic_index = 0; + reg32 = *ioapic_data; + printk_debug("Southbridge APIC ID = %x\n", (reg32 >> 24) & 0x0f); + if (reg32 != (1 << 25)) + die("APIC Error\n"); + + printk_spew("Dumping IOAPIC registers\n"); + for (i=0; i<3; i++) { + *ioapic_index = i; + printk_spew(" reg 0x%04x:", i); + reg32 = *ioapic_data; + printk_spew(" 0x%08x\n", reg32); + } + + *ioapic_index = 3; /* Select Boot Configuration register. */ + *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */ +} + +static void i82801gx_enable_serial_irqs(struct device *dev) +{ + /* Set packet length and toggle silent mode bit for one frame. */ + pci_write_config8(dev, SERIRQ_CNTL, + (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0)); +} + +static void i82801gx_pirq_init(device_t dev) +{ + pci_write_config8(dev, PIRQA_ROUT, 0x85); + pci_write_config8(dev, PIRQB_ROUT, 0x87); + pci_write_config8(dev, PIRQC_ROUT, 0x86); + pci_write_config8(dev, PIRQD_ROUT, 0x87); + + pci_write_config8(dev, PIRQE_ROUT, 0x80); + pci_write_config8(dev, PIRQF_ROUT, 0x80); + pci_write_config8(dev, PIRQG_ROUT, 0x80); + pci_write_config8(dev, PIRQH_ROUT, 0x85); +} + +static void i82801gx_power_options(device_t dev) +{ + u8 reg8; + u16 reg16; + + int pwr_on=MAINBOARD_POWER_ON_AFTER_POWER_FAIL; + int nmi_option; + + /* Which state do we want to goto after g3 (power restored)? + * 0 == S0 Full On + * 1 == S5 Soft Off + */ + get_option(&pwr_on, "power_on_after_fail"); + reg8 = pci_read_config8(dev, GEN_PMCON_3); + reg8 &= 0xfe; + if (pwr_on) { + reg8 &= ~1; + } else { + reg8 |= 1; + } + reg8 |= (3 << 4); /* avoid #S4 assertions */ + + pci_write_config8(dev, GEN_PMCON_3, reg8); + printk_info("Set power %s after power failure.\n", pwr_on ? "on" : "off"); + + /* Set up NMI on errors. */ + reg8 = inb(0x61); + reg8 &= 0x0f; /* Higher Nibble must be 0 */ + reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */ + // reg8 &= ~(1 << 2); /* PCI SERR# Enable */ + reg8 |= (1 << 2); /* PCI SERR# Disable for now */ + outb(reg8, 0x61); + + reg8 = inb(0x70); + nmi_option = NMI_OFF; + get_option(&nmi_option, "nmi"); + if (nmi_option) { + printk_info ("NMI sources enabled.\n"); + reg8 &= ~(1 << 7); /* Set NMI. */ + } else { + printk_info ("NMI sources disabled.\n"); + reg8 |= ( 1 << 7); /* Can't mask NMI from PCI-E and NMI_NOW */ + } + outb(reg8, 0x70); + + // Enable CPU_SLP# and Intel Speedstep, set SMI# rate down + reg16 = pci_read_config16(dev, GEN_PMCON_1); + reg16 &= ~3; + reg16 |= (1 << 3) | (1 << 5) | (1 << 10); + pci_write_config16(dev, GEN_PMCON_1, reg16); + + // Set GPIO13 to SCI (?) + // This might be board specific + pci_write_config32(dev, 0xb8, 0x08000000); +} + +void i82801gx_rtc_init(struct device *dev) +{ + u8 reg8; + u32 reg32; + int rtc_failed; + + reg8 = pci_read_config8(dev, GEN_PMCON_3); + rtc_failed = reg8 & RTC_BATTERY_DEAD; + if (rtc_failed) { + reg8 &= ~RTC_BATTERY_DEAD; + pci_write_config8(dev, GEN_PMCON_3, reg8); + } + printk_debug("rtc_failed = 0x%x\n", rtc_failed); + + rtc_init(rtc_failed); +} + +static void enable_hpet(struct device *dev) +{ + u32 reg32; + u32 code = (0 & 0x3); + + reg32 = pci_read_config32(dev, GEN_CNTL); + reg32 |= (1 << 17); /* Enable HPET. */ + /* + * Bits [16:15] Memory Address Range + * 00 FED0_0000h - FED0_03FFh + * 01 FED0_1000h - FED0_13FFh + * 10 FED0_2000h - FED0_23FFh + * 11 FED0_3000h - FED0_33FFh + */ + reg32 &= ~(3 << 15); /* Clear it */ + reg32 |= (code << 15); + /* TODO: reg32 is never written to anywhere? */ + printk_debug("Enabling HPET @0x%x\n", HPET_ADDR | (code << 12)); +} + +static void i82801gx_lock_smm(struct device *dev) +{ + void smm_lock(void); + u8 reg8; + +#if ENABLE_ACPI_MODE_IN_COREBOOT + printk_debug("Enabling ACPI via APMC:\n"); + outb(0xe1, 0xb2); // Enable ACPI mode + printk_debug("done.\n"); +#else + printk_debug("Disabling ACPI via APMC:\n"); + outb(0x1e, 0xb2); // Disable ACPI mode + printk_debug("done.\n"); +#endif + /* Don't allow evil boot loaders, kernels, or + * userspace applications to deceive us: + */ + smm_lock(); + +#if TEST_SMM_FLASH_LOCKDOWN + /* Now try this: */ + printk_debug("Locking BIOS to RO... "); + reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ + printk_debug(" BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", + (reg8&1)?"rw":"ro"); + reg8 &= ~(1 << 0); /* clear BIOSWE */ + pci_write_config8(dev, 0xdc, reg8); + reg8 |= (1 << 1); /* set BLE */ + pci_write_config8(dev, 0xdc, reg8); + printk_debug("ok.\n"); + reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ + printk_debug(" BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", + (reg8&1)?"rw":"ro"); + + printk_debug("Writing:\n"); + *(volatile u8 *)0xfff00000 = 0x00; + printk_debug("Testing:\n"); + reg8 |= (1 << 0); /* set BIOSWE */ + pci_write_config8(dev, 0xdc, reg8); + + reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */ + printk_debug(" BLE: %s; BWE: %s\n", (reg8&2)?"on":"off", + (reg8&1)?"rw":"ro"); + printk_debug("Done.\n"); +#endif +} + +static void lpc_init(struct device *dev) +{ + printk_debug("i82801gx: lpc_init\n"); + + /* Set the value for PCI command register. */ + pci_write_config16(dev, PCI_COMMAND, 0x000f); + + /* IO APIC initialization. */ + i82801gx_enable_apic(dev); + + i82801gx_enable_serial_irqs(dev); + + /* Setup the PIRQ. */ + i82801gx_pirq_init(dev); + + /* Setup power options. */ + i82801gx_power_options(dev); + + /* Set the state of the GPIO lines. */ + //gpio_init(dev); + + /* Initialize the real time clock. */ + i82801gx_rtc_init(dev); + + /* Initialize ISA DMA. */ + isa_dma_init(); + + /* Initialize the High Precision Event Timers, if present. */ + enable_hpet(dev); + + setup_i8259(); + + i82801gx_lock_smm(dev); +} + +static void i82801gx_lpc_read_resources(device_t dev) +{ + struct resource *res; + + /* Get the normal PCI resources of this device. */ + pci_dev_read_resources(dev); + + /* Add an extra subtractive resource for both memory and I/O. */ + res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0)); + res->flags = + IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; + + res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0)); + res->flags = + IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; +} + +static void i82801gx_lpc_enable_resources(device_t dev) +{ + pci_dev_enable_resources(dev); + enable_childrens_resources(dev); +} + +static void set_subsystem(device_t dev, unsigned vendor, unsigned device) +{ + printk_debug("Setting LPC bridge subsystem ID\n"); + pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, + pci_read_config32(dev, 0)); +} + +static struct pci_operations pci_ops = { + .set_subsystem = set_subsystem, +}; + +static struct device_operations device_ops = { + .read_resources = i82801gx_lpc_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = i82801gx_lpc_enable_resources, + .init = lpc_init, + .scan_bus = scan_static_bus, + .enable = i82801gx_enable, + .ops_pci = &pci_ops, +}; + +/* ICH7 / ICH7R */ +static const struct pci_driver ich7_ich7r_lpc __pci_driver = { + .ops = &device_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27b8, +}; + +/* ICH7M / ICH7U */ +static const struct pci_driver ich7m_ich7u_lpc __pci_driver = { + .ops = &device_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27b9, +}; + +/* ICH7M DH */ +static const struct pci_driver ich7m_dh_lpc __pci_driver = { + .ops = &device_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27bd, +}; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nic.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nic.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nic.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,50 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* This code should work for all ICH* southbridges with a NIC. */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> + +static void nic_init(struct device *dev) +{ + /* Nothing yet */ +} + +static struct device_operations nic_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = nic_init, + .scan_bus = 0, +}; + +/* 82801GB/GR/GDH/GBM/GHM (ICH7/ICH7R/ICH7DH/ICH7-M/ICH7-M DH) */ +/* Note: 82801GU (ICH7-U) doesn't have a NIC. */ +/* PCI ID loaded from EEPROM. If EEPROM is 0, 0x27dc is used */ +static const struct pci_driver i82801gb_nic __pci_driver = { + .ops = &nic_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_LAN, +}; + +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,108 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +typedef struct { + u16 osys; + u8 smif; + u8 prm0; + u8 prm1; + u8 scif; + u8 prm2; + u8 prm3; + u8 lckf; + u8 prm4; + u8 prm5; + u32 p80d; + u8 lids; + u8 pwrs; + u8 dbgs; + u8 linxs; + u8 rsvd; + u8 actt; + u8 psvt; + u8 tc1v; + u8 tc2v; + u8 tspv; + u8 crtt; + u8 dtse; + u8 dts1; + u8 dts2; + u8 rsvd2; + u8 bnum; + u8 b0sc, b1sc, b2sc; + u8 b0ss, b1ss, b2ss; + u8 rsvd3[3]; + u8 apic; + u8 mpen; + u8 bten; + u8 ppcm; + u8 pcp0; + u8 pcp1; + u8 rsvd4[4]; + u8 natp; + u8 cmap; + u8 cmbp; + u8 lptp; + u8 fdcp; + u8 rfdv; + u8 hotk; + u8 rtcf; + u8 util; + u8 acin; + u8 igds; + u8 tlst; + u8 cadl; + u8 padl; + u16 cste; + u16 pste; + u16 nste; + u16 sste; + u8 ndid; + u32 did1; + u32 did2; + u32 did3; + u32 did4; + u32 did5; + u8 rsvd5[0xb]; + u8 brtl; + u8 odds; + u8 alse; + u8 alaf; + u8 llow; + u8 lhih; + u8 rsvd6; + u8 emae; + u16 emap; + u16 emal; + u8 rsvd7; + u8 mefe; + u8 igps; + u8 rsvd8[2]; + u8 tpmp; + u8 tpme; + u8 rsvd9[8]; + u8 gtf0[7]; + u8 gtf2[7]; + u8 idem; + u8 idet; + u8 dock; +} global_nvs_t; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,141 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> + +static void pci_init(struct device *dev) +{ + u16 reg16; + +#if 0 + /* Commented out for now because it will break on some machines. */ + /* Set latency timer to 32. */ + pci_write_config16(dev, 0x1b, 0x20); +#endif + + /* disable parity error response */ + reg16 = pci_read_config16(dev, 0x3e); + reg16 &= ~(1 << 0); + pci_write_config16(dev, 0x3e, reg16); + + /* Clear errors in status registers */ + reg16 = pci_read_config16(dev, 0x06); + reg16 |= 0xf900; + pci_write_config16(dev, 0x06, reg16); + + reg16 = pci_read_config16(dev, 0x1e); + reg16 |= 0xf900; + pci_write_config16(dev, 0x1e, reg16); +} + +static void ich_pci_dev_enable_resources(struct device *dev) +{ + const struct pci_operations *ops; + uint16_t command; + + /* Set the subsystem vendor and device id for mainboard devices */ + ops = ops_pci(dev); + if (dev->on_mainboard && ops && ops->set_subsystem) { + printk_debug("%s subsystem <- %02x/%02x\n", + dev_path(dev), + MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID, + MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID); + ops->set_subsystem(dev, + MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID, + MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID); + } + +#if 0 + /* If we write to PCI_COMMAND, on some systems + * this will cause the ROM and APICs not being visible + * anymore. + */ + command = pci_read_config16(dev, PCI_COMMAND); + command |= dev->command; + printk_debug("%s cmd <- %02x\n", dev_path(dev), command); + pci_write_config16(dev, PCI_COMMAND, command); +#endif +} + +static void ich_pci_bus_enable_resources(struct device *dev) +{ + uint16_t ctrl; + /* enable IO in command register if there is VGA card + * connected with (even it does not claim IO resource) + */ + if (dev->link[0].bridge_ctrl & PCI_BRIDGE_CTL_VGA) + dev->command |= PCI_COMMAND_IO; + ctrl = pci_read_config16(dev, PCI_BRIDGE_CONTROL); + ctrl |= dev->link[0].bridge_ctrl; + ctrl |= (PCI_BRIDGE_CTL_PARITY + PCI_BRIDGE_CTL_SERR); /* error check */ + printk_debug("%s bridge ctrl <- %04x\n", dev_path(dev), ctrl); + pci_write_config16(dev, PCI_BRIDGE_CONTROL, ctrl); + + /* This is the reason we need our own pci_bus_enable_resources */ + ich_pci_dev_enable_resources(dev); + + enable_childrens_resources(dev); +} + +static void set_subsystem(device_t dev, unsigned vendor, unsigned device) +{ +#if 0 + /* Currently disabled because it causes a "BAR 9" memory resource + * conflict: + */ + u32 pci_id; + + printk_debug("Setting PCI bridge subsystem ID\n"); + pci_id = pci_read_config32(dev, 0); + pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, pci_id ); +#endif +} + +static struct pci_operations pci_ops = { + .set_subsystem = set_subsystem, +}; + +static struct device_operations device_ops = { + .read_resources = pci_bus_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = ich_pci_bus_enable_resources, + .init = pci_init, + .scan_bus = pci_scan_bridge, + .ops_pci = &pci_ops, +}; + + +/* Desktop */ +static const struct pci_driver i82801g_pci __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x244e, +}; + +/* Mobile / Ultra Mobile */ +static const struct pci_driver i82801gmu_pci __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x2448, +}; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pcie.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pcie.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pcie.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,126 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> + +static void pci_init(struct device *dev) +{ + u16 reg16; + u32 reg32; + + printk_debug("Initializing ICH7 PCIe bridge.\n"); +#if 0 + // When the latency of the PCIe(!) bridge is set to 0x20 + // all devices on the secondary bus of the PCI(!) bridge + // suddenly vanish. If you know why, please explain here. + + /* Set latency timer to 32. */ + pci_write_config16(dev, 0x1b, 0x20); +#endif + + /* disable parity error response */ + reg16 = pci_read_config16(dev, 0x3e); + reg16 &= ~(1 << 0); + pci_write_config16(dev, 0x3e, reg16); + + /* Clear errors in status registers */ + reg16 = pci_read_config16(dev, 0x06); + reg16 |= 0xf900; + pci_write_config16(dev, 0x06, reg16); + + reg16 = pci_read_config16(dev, 0x1e); + reg16 |= 0xf900; + pci_write_config16(dev, 0x1e, reg16); + + reg32 = pci_read_config32(dev, 0x20); + printk_debug(" MBL = 0x%08x\n", reg32); + reg32 = pci_read_config32(dev, 0x24); + printk_debug(" PMBL = 0x%08x\n", reg32); + reg32 = pci_read_config32(dev, 0x28); + printk_debug(" PMBU32 = 0x%08x\n", reg32); + reg32 = pci_read_config32(dev, 0x2c); + printk_debug(" PMLU32 = 0x%08x\n", reg32); +} + +static void set_subsystem(device_t dev, unsigned vendor, unsigned device) +{ + u32 pci_id; + + printk_debug("Setting PCIe bridge subsystem ID.\n"); + pci_id = pci_read_config32(dev, 0); + pci_write_config32(dev, 0x94, pci_id ); +} + +static struct pci_operations pci_ops = { + .set_subsystem = set_subsystem, +}; + +static struct device_operations device_ops = { + .read_resources = pci_bus_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_bus_enable_resources, + .init = pci_init, + .scan_bus = pci_scan_bridge, + .ops_pci = &pci_ops, +}; + +static const struct pci_driver i82801gx_pcie_port1 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27d0, +}; + +static const struct pci_driver i82801gx_pcie_port2 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27d2, +}; + +static const struct pci_driver i82801gx_pcie_port3 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27d4, +}; + +static const struct pci_driver i82801gx_pcie_port4 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27d6, +}; + +static const struct pci_driver i82801gx_pcie_port5 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27e0, +}; + +static const struct pci_driver i82801gx_pcie_port6 __pci_driver = { + .ops = &device_ops, + .vendor = 0x8086, + .device = 0x27e2, +}; + + + + +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_reset.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_reset.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_reset.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,27 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <arch/io.h> + +void hard_reset(void) +{ + /* Try rebooting through port 0xcf9. */ + outb((1 << 2) | (1 << 1), 0xcf9); +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,190 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "i82801gx.h" + +typedef struct southbridge_intel_i82801gx_config config_t; + +static void sata_init(struct device *dev) +{ + u32 reg32; + /* Get the chip configuration */ + config_t *config = dev->chip_info; + + printk_debug("i82801gx_sata: initializing...\n"); + /* SATA configuration */ + + /* Enable BARs */ + pci_write_config16(dev, 0x04, 0x0007); + + if (config->ide_legacy_combined) { + pci_write_config8(dev, 0x09, 0x80); + + /* Set timings */ + pci_write_config16(dev, IDE_TIM_PRI, 0x8000); + pci_write_config16(dev, IDE_TIM_SEC, 0xa307); + + /* Sync DMA */ + pci_write_config16(dev, 0x48, 0x0004); + pci_write_config16(dev, 0x4a, 0x0200); + + /* Combine IDE - SATA configuration */ + pci_write_config8(dev, 0x90, 0x02); + + /* Port 0 & 1 enable */ + pci_write_config8(dev, 0x92, 0x0f); + + /* SATA Initialization register */ + pci_write_config32(dev, 0x94, 0x40000180); + } else if(config->sata_ahci) { + /* Allow both Legacy and Native mode */ + pci_write_config8(dev, 0x09, 0x8f); + + /* Set Interrupt Line */ + /* Interrupt Pin is set by D31IP.PIP */ + pci_write_config8(dev, INTR_LN, 0x0a); + + /* Set timings */ + pci_write_config16(dev, IDE_TIM_PRI, 0xa307); + pci_write_config16(dev, IDE_TIM_SEC, 0x8000); + + /* Sync DMA */ + pci_write_config16(dev, 0x48, 0x0001); + pci_write_config16(dev, 0x4a, 0x0001); + + /* Set IDE I/O Configuration */ + reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + pci_write_config32(dev, IDE_CONFIG, reg32); + + /* Set Sata Controller Mode. */ + pci_write_config8(dev, 0x90, 0xc0); // WTF - Reserved? + + /* Port 0 & 1 enable */ + pci_write_config8(dev, 0x92, 0x0f); + + /* SATA Initialization register */ + pci_write_config32(dev, 0x94, 0x1a000180); + } else { + /* Native mode capable on both primary and secondary (0xa) + * or'ed with enabled (0x50) = 0xf + */ + pci_write_config8(dev, 0x09, 0x8f); + + /* Set Interrupt Line */ + /* Interrupt Pin is set by D31IP.PIP */ + pci_write_config8(dev, INTR_LN, 0xff); + + /* Set timings */ + pci_write_config16(dev, IDE_TIM_PRI, 0xa307); + pci_write_config16(dev, IDE_TIM_SEC, 0xe303); + + /* Sync DMA */ + pci_write_config16(dev, 0x48, 0x0005); + pci_write_config16(dev, 0x4a, 0x0201); + + /* Set IDE I/O Configuration */ + reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; + pci_write_config32(dev, IDE_CONFIG, reg32); + + /* Set Sata Controller Mode. */ + pci_write_config8(dev, 0x90, 0x02); + + /* Port 0 & 1 enable XXX */ + pci_write_config8(dev, 0x92, 0x15); + + /* SATA Initialization register */ + pci_write_config32(dev, 0x94, 0x1a000180); + } + + /* All configurations need this SATA initialization sequence */ + pci_write_config8(dev, 0xa0, 0x40); + pci_write_config8(dev, 0xa6, 0x22); + pci_write_config8(dev, 0xa0, 0x78); + pci_write_config8(dev, 0xa6, 0x22); + pci_write_config8(dev, 0xa0, 0x88); + reg32 = pci_read_config32(dev, 0xa4); + reg32 &= 0xc0c0c0c0; + reg32 |= 0x1b1b1212; + pci_write_config32(dev, 0xa4, reg32); + pci_write_config8(dev, 0xa0, 0x8c); + reg32 = pci_read_config32(dev, 0xa4); + reg32 &= 0xc0c0ff00; + reg32 |= 0x121200aa; + pci_write_config32(dev, 0xa4, reg32); + pci_write_config8(dev, 0xa0, 0x00); +} + +static struct device_operations sata_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = sata_init, + .scan_bus = 0, + .enable = i82801gx_enable, +}; + +/* Desktop Non-AHCI and Non-RAID Mode */ +static const struct pci_driver i82801gx_sata_normal_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c0, +}; + +/* NOTE: Any of the below are not properly supported yet */ + +/* Desktop AHCI Mode */ +static const struct pci_driver i82801gx_sata_ahci_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c1, +}; + +/* Desktop RAID mode */ +static const struct pci_driver i82801gx_sata_raid_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c3, +}; + +/* Mobile Non-AHCI and Non-RAID Mode */ +static const struct pci_driver i82801gx_sata_mobile_normal_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c4, +}; + +/* Mobile AHCI Mode */ +static const struct pci_driver i82801gx_sata_mobile_ahci_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c5, +}; + +/* ICH7M DH Raid Mode */ +static const struct pci_driver i82801gx_sata_ich7dh_raid_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27c6, +}; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,59 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <stdint.h> +#include <smbus.h> +#include <pci.h> +#include <arch/io.h> +#include "i82801gx.h" +#include "i82801_smbus.h" + +static int smbus_read_byte(struct bus *bus, device_t dev, u8 address) +{ + u16 device; + struct resource *res; + + device = dev->path.u.i2c.device; + res = find_resource(bus->dev, 0x20); + + return do_smbus_read_byte(res->base, device, address); +} + +static struct smbus_bus_operations lops_smbus_bus = { + .read_byte = smbus_read_byte, +}; + +static struct device_operations smbus_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = 0, + .scan_bus = scan_static_bus, + .enable = i82801gx_enable, + .ops_smbus_bus = &lops_smbus_bus, +}; + +/* 82801GB/GR/GDH/GBM/GHM/GU (ICH7/ICH7R/ICH7DH/ICH7-M/ICH7-M DH/ICH7-U) */ +static const struct pci_driver i82801gx_smbus __pci_driver = { + .ops = &smbus_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_SMB, +}; +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.h =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.h (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.h 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,187 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2005 Yinghai Lu yinghailu@gmail.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <device/smbus_def.h> + +static void smbus_delay(void) +{ + inb(0x80); +} + +static int smbus_wait_until_ready(void) +{ + unsigned loops = SMBUS_TIMEOUT; + unsigned char byte; + do { + smbus_delay(); + if (--loops == 0) + break; + byte = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } while (byte & 1); + return loops ? 0 : -1; +} + +static int smbus_wait_until_done(void) +{ + unsigned loops = SMBUS_TIMEOUT; + unsigned char byte; + do { + smbus_delay(); + if (--loops == 0) + break; + byte = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } while ((byte & 1) || (byte & ~((1 << 6) | (1 << 0))) == 0); + return loops ? 0 : -1; +} + +static int smbus_wait_until_blk_done(void) +{ + unsigned loops = SMBUS_TIMEOUT; + unsigned char byte; + do { + smbus_delay(); + if (--loops == 0) + break; + byte = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } while ((byte & (1 << 7)) == 0); + return loops ? 0 : -1; +} + +static int do_smbus_read_byte(unsigned device, unsigned address) +{ + unsigned char global_status_register; + unsigned char byte; + + if (smbus_wait_until_ready() < 0) { + return SMBUS_WAIT_UNTIL_READY_TIMEOUT; + } + /* Setup transaction */ + /* Disable interrupts */ + outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL); + /* Set the device I'm talking too */ + outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD); + /* Set the command/address... */ + outb(address & 0xff, SMBUS_IO_BASE + SMBHSTCMD); + /* Set up for a byte data read */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2 << 2), + (SMBUS_IO_BASE + SMBHSTCTL)); + /* Clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + + /* Clear the data byte... */ + outb(0, SMBUS_IO_BASE + SMBHSTDAT0); + + /* Start the command */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), + SMBUS_IO_BASE + SMBHSTCTL); + + /* Poll for transaction completion */ + if (smbus_wait_until_done() < 0) { + return SMBUS_WAIT_UNTIL_DONE_TIMEOUT; + } + + global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT); + + /* Ignore the "In Use" status... */ + global_status_register &= ~(3 << 5); + + /* Read results of transaction */ + byte = inb(SMBUS_IO_BASE + SMBHSTDAT0); + if (global_status_register != (1 << 1)) { + return SMBUS_ERROR; + } + return byte; +} + +/* This function is neither used nor tested by me (Corey Osgood), the author +(Yinghai) probably tested/used it on i82801er */ +static int do_smbus_write_block(unsigned device, unsigned length, unsigned cmd, + unsigned data1, unsigned data2) +{ + unsigned char byte; + unsigned char stat; + int i; + +#if CONFIG_USE_PRINTK_IN_CAR + printk_err("Untested smbus_write_block called\r\n"); +#else + print_err("Untested smbus_write_block called\r\n"); +#endif + + /* Clear the PM timeout flags, SECOND_TO_STS */ + outw(inw(0x0400 + 0x66), 0x0400 + 0x66); + + if (smbus_wait_until_ready() < 0) { + return -2; + } + + /* Setup transaction */ + /* Obtain ownership */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + for (stat = 0; (stat & 0x40) == 0;) { + stat = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } + /* Clear the done bit */ + outb(0x80, SMBUS_IO_BASE + SMBHSTSTAT); + /* Disable interrupts */ + outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL); + + /* Set the device I'm talking too */ + outb(((device & 0x7f) << 1), SMBUS_IO_BASE + SMBXMITADD); + + /* Set the command address */ + outb(cmd & 0xff, SMBUS_IO_BASE + SMBHSTCMD); + + /* Set the block length */ + outb(length & 0xff, SMBUS_IO_BASE + SMBHSTDAT0); + + /* Try sending out the first byte of data here */ + byte = (data1 >> (0)) & 0x0ff; + outb(byte, SMBUS_IO_BASE + SMBBLKDAT); + /* Issue a block write command */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x5 << 2) | 0x40, + SMBUS_IO_BASE + SMBHSTCTL); + + for (i = 0; i < length; i++) { + + /* Poll for transaction completion */ + if (smbus_wait_until_blk_done() < 0) { + return -3; + } + + /* Load the next byte */ + if (i > 3) + byte = (data2 >> (i % 4)) & 0x0ff; + else + byte = (data1 >> (i)) & 0x0ff; + outb(byte, SMBUS_IO_BASE + SMBBLKDAT); + + /* Clear the done bit */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), + SMBUS_IO_BASE + SMBHSTSTAT); + } + +#if CONFIG_USE_PRINTK_IN_CAR + printk_debug("SMBUS Block complete\r\n"); +#else + print_debug("SMBUS Block complete\r\n"); +#endif + return 0; +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,335 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + + +#include <device/device.h> +#include <device/pci.h> +#include <console/console.h> +#include <arch/io.h> +#include <cpu/x86/cache.h> +#include <cpu/x86/smm.h> +#include <string.h> +#include "chip.h" + +// Future TODO: Move to i82801gx directory +#include "../../../northbridge/intel/i945/ich7.h" + +extern unsigned char smm[]; +extern unsigned int smm_len; + +/* I945 */ +#define SMRAM 0x9d +#define D_OPEN (1 << 6) +#define D_CLS (1 << 5) +#define D_LCK (1 << 4) +#define G_SMRAME (1 << 3) +#define C_BASE_SEG ((0 << 2) | (1 << 1) | (0 << 0)) + +/* ICH7 */ +#define PM1_STS 0x00 +#define PM1_EN 0x02 +#define PM1_CNT 0x04 +#define PM1_TMR 0x08 +#define PROC_CNT 0x10 +#define LV2 0x14 +#define LV3 0x15 +#define LV4 0x16 +#define PM2_CNT 0x20 // mobile only +#define GPE0_STS 0x28 +#define GPE0_EN 0x2c +#define SMI_EN 0x30 +#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology +#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic +#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic +#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS +#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) +#define MCSMI_EN (1 << 11) // Trap microcontroller range access +#define BIOS_RLS (1 << 7) // asserts SCI on bit set +#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set +#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# +#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# +#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic +#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit +#define EOS (1 << 1) // End of SMI (deassert SMI#) +#define GBL_SMI_EN (1 << 0) // SMI# generation at all? +#define SMI_STS 0x34 +#define ALT_GP_SMI_EN 0x38 +#define ALT_GP_SMI_STS 0x3a +#define GPE_CNTL 0x42 +#define DEVACT_STS 0x44 +#define SS_CNT 0x50 +#define C3_RES 0x54 + +/* While we read PMBASE dynamically in case it changed, let's + * initialize it with a sane value + */ +static u16 pmbase = DEFAULT_PMBASE; + +/** + * @brief read and clear PM1_STS + * @return PM1_STS register + */ +static u16 reset_pm1_status(void) +{ + u16 reg16; + + reg16 = inw(pmbase + PM1_STS); + /* set status bits are cleared by writing 1 to them */ + outw(reg16, pmbase + PM1_STS); + + return reg16; +} + +static void dump_pm1_status(u16 pm1_sts) +{ + printk_debug("PM1_STS: "); + if (pm1_sts & (1 << 15)) printk_debug("WAK "); + if (pm1_sts & (1 << 14)) printk_debug("PCIEXPWAK "); + if (pm1_sts & (1 << 11)) printk_debug("PRBTNOR "); + if (pm1_sts & (1 << 10)) printk_debug("RTC "); + if (pm1_sts & (1 << 8)) printk_debug("PWRBTN "); + if (pm1_sts & (1 << 5)) printk_debug("GBL "); + if (pm1_sts & (1 << 4)) printk_debug("BM "); + if (pm1_sts & (1 << 0)) printk_debug("TMROF "); + printk_debug("\n"); +} + +/** + * @brief read and clear SMI_STS + * @return SMI_STS register + */ +static u32 reset_smi_status(void) +{ + u32 reg32; + + reg32 = inl(pmbase + SMI_STS); + /* set status bits are cleared by writing 1 to them */ + outl(reg32, pmbase + SMI_STS); + + return reg32; +} + +static void dump_smi_status(u32 smi_sts) +{ + printk_debug("SMI_STS: "); + if (smi_sts & (1 << 26)) printk_debug("SPI "); + if (smi_sts & (1 << 25)) printk_debug("EL_SMI "); + if (smi_sts & (1 << 21)) printk_debug("MONITOR "); + if (smi_sts & (1 << 20)) printk_debug("PCI_EXP_SMI "); + if (smi_sts & (1 << 18)) printk_debug("INTEL_USB2 "); + if (smi_sts & (1 << 17)) printk_debug("LEGACY_USB2 "); + if (smi_sts & (1 << 16)) printk_debug("SMBUS_SMI "); + if (smi_sts & (1 << 15)) printk_debug("SERIRQ_SMI "); + if (smi_sts & (1 << 14)) printk_debug("PERIODIC "); + if (smi_sts & (1 << 13)) printk_debug("TCO "); + if (smi_sts & (1 << 12)) printk_debug("DEVMON "); + if (smi_sts & (1 << 11)) printk_debug("MCSMI "); + if (smi_sts & (1 << 10)) printk_debug("GPI "); + if (smi_sts & (1 << 9)) printk_debug("GPE0 "); + if (smi_sts & (1 << 8)) printk_debug("PM1 "); + if (smi_sts & (1 << 6)) printk_debug("SWSMI_TMR "); + if (smi_sts & (1 << 5)) printk_debug("APM "); + if (smi_sts & (1 << 4)) printk_debug("SLP_SMI "); + if (smi_sts & (1 << 3)) printk_debug("LEGACY_USB "); + if (smi_sts & (1 << 2)) printk_debug("BIOS "); + printk_debug("\n"); +} + + +/** + * @brief read and clear GPE0_STS + * @return GPE0_STS register + */ +static u32 reset_gpe0_status(void) +{ + u32 reg32; + + reg32 = inl(pmbase + GPE0_STS); + /* set status bits are cleared by writing 1 to them */ + outl(reg32, pmbase + GPE0_STS); + + return reg32; +} + +static void dump_gpe0_status(u32 gpe0_sts) +{ + int i; + printk_debug("GPE0_STS: "); + for (i=31; i<= 16; i--) { + if (gpe0_sts & (1 << i)) printk_debug("GPIO%d ", (i-16)); + } + if (gpe0_sts & (1 << 14)) printk_debug("USB4 "); + if (gpe0_sts & (1 << 13)) printk_debug("PME_B0 "); + if (gpe0_sts & (1 << 12)) printk_debug("USB3 "); + if (gpe0_sts & (1 << 11)) printk_debug("PME "); + if (gpe0_sts & (1 << 10)) printk_debug("EL_SCI/BATLOW "); + if (gpe0_sts & (1 << 9)) printk_debug("PCI_EXP "); + if (gpe0_sts & (1 << 8)) printk_debug("RI "); + if (gpe0_sts & (1 << 7)) printk_debug("SMB_WAK "); + if (gpe0_sts & (1 << 6)) printk_debug("TCO_SCI "); + if (gpe0_sts & (1 << 5)) printk_debug("AC97 "); + if (gpe0_sts & (1 << 4)) printk_debug("USB2 "); + if (gpe0_sts & (1 << 3)) printk_debug("USB1 "); + if (gpe0_sts & (1 << 2)) printk_debug("HOT_PLUG "); + if (gpe0_sts & (1 << 0)) printk_debug("THRM "); + printk_debug("\n"); +} + +/** + * @brief read and clear TCOx_STS + * @return TCOx_STS registers + */ +static u32 reset_tco_status(void) +{ + u32 tcobase = pmbase + 0x60; + u32 reg32; + + reg32 = inl(tcobase + 0x04); + /* set status bits are cleared by writing 1 to them */ + outl(reg32 & ~(1<<18), tcobase + 0x04); // Don't clear BOOT_STS before SECOND_TO_STS + if (reg32 & (1 << 18)) + outl(reg32 & (1<<18), tcobase + 0x04); // clear BOOT_STS + + return reg32; +} + + +static void dump_tco_status(u32 tco_sts) +{ + printk_debug("TCO_STS: "); + if (tco_sts & (1 << 20)) printk_debug("SMLINK_SLV "); + if (tco_sts & (1 << 18)) printk_debug("BOOT "); + if (tco_sts & (1 << 17)) printk_debug("SECOND_TO "); + if (tco_sts & (1 << 16)) printk_debug("INTRD_DET "); + if (tco_sts & (1 << 12)) printk_debug("DMISERR "); + if (tco_sts & (1 << 10)) printk_debug("DMISMI "); + if (tco_sts & (1 << 9)) printk_debug("DMISCI "); + if (tco_sts & (1 << 8)) printk_debug("BIOSWR "); + if (tco_sts & (1 << 7)) printk_debug("NEWCENTURY "); + if (tco_sts & (1 << 3)) printk_debug("TIMEOUT "); + if (tco_sts & (1 << 2)) printk_debug("TCO_INT "); + if (tco_sts & (1 << 1)) printk_debug("SW_TCO "); + if (tco_sts & (1 << 0)) printk_debug("NMI2SMI "); + printk_debug("\n"); +} + + + +/** + * @brief Set the EOS bit + */ +static void smi_set_eos(void) +{ + u8 reg8; + + reg8 = inb(pmbase + SMI_EN); + reg8 |= EOS; + outb(reg8, pmbase + SMI_EN); +} + +extern uint8_t smm_relocation_start, smm_relocation_end; + +void smm_relocate(void) +{ + u32 smi_en; + + printk_debug("Initializing SMM handler..."); + + pmbase = pci_read_config16(dev_find_slot(0, PCI_DEVFN(0x1f, 0)), 0x40) & 0xfffc; + printk_spew(" ... pmbase = 0x%04x\n", pmbase); + + smi_en = inl(pmbase + SMI_EN); + if (smi_en & APMC_EN) { + printk_info("SMI# handler already enabled?\n"); + return; + } + + /* copy the SMM relocation code */ + memcpy((void *)0x38000, &smm_relocation_start, + &smm_relocation_end - &smm_relocation_start); + + printk_debug("\n"); + dump_smi_status(reset_smi_status()); + dump_pm1_status(reset_pm1_status()); + dump_gpe0_status(reset_gpe0_status()); + dump_tco_status(reset_tco_status()); + + /* Enable SMI generation: + * - on TCO events + * - on APMC writes (io 0xb2) + * - on writes to SLP_EN (sleep states) + * - on writes to GBL_RLS (bios commands) + * No SMIs: + * - on microcontroller writes (io 0x62/0x66) + */ + outl(smi_en | (TCO_EN | APMC_EN | SLP_SMI_EN | BIOS_EN | + EOS | GBL_SMI_EN), pmbase + SMI_EN); + + /** + * There are several methods of raising a controlled SMI# via + * software, among them: + * - Writes to io 0xb2 (APMC) + * - Writes to the Local Apic ICR with Delivery mode SMI. + * + * Using the local apic is a bit more tricky. According to + * AMD Family 11 Processor BKDG no destination shorthand must be + * used. + * The whole SMM initialization is quite a bit hardware specific, so + * I'm not too worried about the better of the methods at the moment + */ + + /* raise an SMI interrupt */ + printk_spew(" ... raise SMI#\n"); + outb(0x00, 0xb2); +} + +void smm_install(void) +{ + /* enable the SMM memory window */ + pci_write_config8(dev_find_slot(0, PCI_DEVFN(0, 0)), SMRAM, + D_OPEN | G_SMRAME | C_BASE_SEG); + + /* copy the real SMM handler */ + memcpy((void *)0xa0000, smm, smm_len); + wbinvd(); + + /* close the SMM memory window and enable normal SMM */ + pci_write_config8(dev_find_slot(0, PCI_DEVFN(0, 0)), SMRAM, + G_SMRAME | C_BASE_SEG); +} + +void smm_init(void) +{ + smm_relocate(); + smm_install(); +} + +void smm_lock(void) +{ + /* LOCK the SMM memory window and enable normal SMM. + * After running this function, only a full reset can + * make the SMM registers writable again. + */ + printk_debug("Locking SMM.\n"); + pci_write_config8(dev_find_slot(0, PCI_DEVFN(0, 0)), SMRAM, + D_LCK | G_SMRAME | C_BASE_SEG); +} +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,79 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "i82801gx.h" + +static void usb_init(struct device *dev) +{ + u32 reg32; + u8 reg8; + + /* USB Specification says the device must be Bus Master */ + printk_debug("UHCI: Setting up controller.. "); + + reg32 = pci_read_config32(dev, PCI_COMMAND); + pci_write_config32(dev, PCI_COMMAND, reg32 | PCI_COMMAND_MASTER); + + reg8 = pci_read_config8(dev, 0xca); + reg8 |= (1 << 0); + pci_write_config8(dev, 0xca, reg8); + + printk_debug("done.\n"); +} + +static struct device_operations usb_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = usb_init, + .scan_bus = 0, + .enable = i82801gx_enable, +}; + +/* 82801GB/GR/GDH/GBM/GHM/GU (ICH7/ICH7R/ICH7DH/ICH7-M/ICH7-M DH/ICH7-U) */ +static const struct pci_driver i82801gb_usb1 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_USB1, +}; + +static const struct pci_driver i82801gb_usb2 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_USB2, +}; + +static const struct pci_driver i82801gb_usb3 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_USB3, +}; + +static const struct pci_driver i82801gb_usb4 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801GB_USB4, +}; + +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,84 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "i82801gx.h" + +static void usb_ehci_init(struct device *dev) +{ + u32 reg32; + + printk_debug("EHCI: Setting up controller.. "); + reg32 = pci_read_config32(dev, PCI_COMMAND); + pci_write_config32(dev, PCI_COMMAND, reg32 | PCI_COMMAND_MASTER); + + reg32 = pci_read_config32(dev, 0xdc); + reg32 |= (1 << 31) | (1 << 27); + pci_write_config32(dev, 0xdc, reg32); + + reg32 = pci_read_config32(dev, 0xfc); + reg32 &= ~(3 << 2); + reg32 |= (2 << 2) | (1 << 29) | (1 << 17); + pci_write_config32(dev, 0xfc, reg32); + + printk_debug("done.\n"); +} + +static void usb_ehci_set_subsystem(device_t dev, unsigned vendor, + unsigned device) +{ + u8 access_cntl; + + access_cntl = pci_read_config8(dev, 0x80); + + /* Enable writes to protected registers. */ + pci_write_config8(dev, 0x80, access_cntl | 1); + + /* Write the subsystem vendor and device ID. */ + pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, + ((device & 0xffff) << 16) | (vendor & 0xffff)); + + /* Restore protection. */ + pci_write_config8(dev, 0x80, access_cntl); +} + +static struct pci_operations lops_pci = { + .set_subsystem = &usb_ehci_set_subsystem, +}; + +static struct device_operations usb_ehci_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = usb_ehci_init, + .scan_bus = 0, + .enable = i82801gx_enable, + .ops_pci = &lops_pci, +}; + +/* 82801Gx */ +static const struct pci_driver i82801ex_usb_ehci __pci_driver = { + .ops = &usb_ehci_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x27cc, +};
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_watchdog.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_watchdog.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_watchdog.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,52 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <arch/io.h> +#include <device/device.h> +#include <device/pci.h> + +void watchdog_off(void) +{ + device_t dev; + unsigned long value, base; + + /* Turn off the ICH7 watchdog. */ + dev = dev_find_slot(0, PCI_DEVFN(0x1f, 0)); + + /* Enable I/O space. */ + value = pci_read_config16(dev, 0x04); + value |= (1 << 10); + pci_write_config16(dev, 0x04, value); + + /* Get TCO base. */ + base = (pci_read_config32(dev, 0x40) & 0x0fffe) + 0x60; + + /* Disable the watchdog timer. */ + value = inw(base + 0x08); + value |= 1 << 11; + outw(value, base + 0x08); + + /* Clear TCO timeout status. */ + outw(0x0008, base + 0x04); + outw(0x0002, base + 0x06); + + printk_debug("ICH7 watchdog disabled\r\n"); +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/smihandler.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/smihandler.c (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/smihandler.c 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,551 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <arch/io.h> +#include <arch/romcc_io.h> +#include <console/console.h> +#include <cpu/x86/cache.h> +#include <cpu/x86/smm.h> +#include "chip.h" + +// Future TODO: Move to i82801gx directory +#include "../../../northbridge/intel/i945/ich7.h" + +#define DEBUG_SMI + +#define ACPI_DISABLE 0x1e +#define ACPI_ENABLE 0xe1 + +/* I945 */ +#define SMRAM 0x9d +#define D_OPEN (1 << 6) +#define D_CLS (1 << 5) +#define D_LCK (1 << 4) +#define G_SMRANE (1 << 3) +#define C_BASE_SEG ((0 << 2) | (1 << 1) | (0 << 0)) + +/* ICH7 */ +#define PM1_STS 0x00 +#define PM1_EN 0x02 +#define PM1_CNT 0x04 +#define PM1_TMR 0x08 +#define PROC_CNT 0x10 +#define LV2 0x14 +#define LV3 0x15 +#define LV4 0x16 +#define PM2_CNT 0x20 // mobile only +#define GPE0_STS 0x28 +#define GPE0_EN 0x2c +#define SMI_EN 0x30 +#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology +#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic +#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic +#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS +#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) +#define MCSMI_EN (1 << 11) // Trap microcontroller range access +#define BIOS_RLS (1 << 7) // asserts SCI on bit set +#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set +#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# +#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# +#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic +#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit +#define EOS (1 << 1) // End of SMI (deassert SMI#) +#define GBL_SMI_EN (1 << 0) // SMI# generation at all? +#define SMI_STS 0x34 +#define ALT_GP_SMI_EN 0x38 +#define ALT_GP_SMI_STS 0x3a +#define GPE_CNTL 0x42 +#define DEVACT_STS 0x44 +#define SS_CNT 0x50 +#define C3_RES 0x54 + +#include "i82801gx_nvs.h" + +/* While we read PMBASE dynamically in case it changed, let's + * initialize it with a sane value + */ +static u16 pmbase = DEFAULT_PMBASE; + +typedef enum { SMI_LOCKED, SMI_UNLOCKED } smi_semaphore; + +/* SMI multiprocessing semaphore */ +static volatile smi_semaphore smi_handler_status = SMI_UNLOCKED; + +static int smi_obtain_lock(void) +{ + u8 ret = SMI_LOCKED; + + asm volatile ( + "movb %2, %%al\n" + "xchgb %%al, %1\n" + "movb %%al, %0\n" + : "=g" (ret), "=m" (smi_handler_status) + : "g" (SMI_LOCKED) + : "eax" + ); + + return (ret == SMI_UNLOCKED); +} + +static void smi_release_lock(void) +{ + asm volatile ( + "movb %1, %%al\n" + "xchgb %%al, %0\n" + : "=m" (smi_handler_status) + : "g" (SMI_UNLOCKED) + : "eax" + ); +} + +#define LAPIC_ID 0xfee00020 +static inline __attribute__((always_inline)) unsigned long nodeid(void) +{ + return (*((volatile unsigned long *)(LAPIC_ID)) >> 24); +} + + +/** + * @brief read and clear PM1_STS + * @return PM1_STS register + */ +static u16 reset_pm1_status(void) +{ + u16 reg16; + + reg16 = inw(pmbase + PM1_STS); + /* set status bits are cleared by writing 1 to them */ + outw(reg16, pmbase + PM1_STS); + + return reg16; +} + +static void dump_pm1_status(u16 pm1_sts) +{ + printk_debug("PM1_STS: "); + if (pm1_sts & (1 << 15)) printk_debug("WAK "); + if (pm1_sts & (1 << 14)) printk_debug("PCIEXPWAK "); + if (pm1_sts & (1 << 11)) printk_debug("PRBTNOR "); + if (pm1_sts & (1 << 10)) printk_debug("RTC "); + if (pm1_sts & (1 << 8)) printk_debug("PWRBTN "); + if (pm1_sts & (1 << 5)) printk_debug("GBL "); + if (pm1_sts & (1 << 4)) printk_debug("BM "); + if (pm1_sts & (1 << 0)) printk_debug("TMROF "); + printk_debug("\n"); +} + +/** + * @brief read and clear SMI_STS + * @return SMI_STS register + */ +static u32 reset_smi_status(void) +{ + u32 reg32; + + reg32 = inl(pmbase + SMI_STS); + /* set status bits are cleared by writing 1 to them */ + outl(reg32, pmbase + SMI_STS); + + return reg32; +} + +static void dump_smi_status(u32 smi_sts) +{ + printk_debug("SMI_STS: "); + if (smi_sts & (1 << 26)) printk_debug("SPI "); + if (smi_sts & (1 << 25)) printk_debug("EL_SMI "); + if (smi_sts & (1 << 21)) printk_debug("MONITOR "); + if (smi_sts & (1 << 20)) printk_debug("PCI_EXP_SMI "); + if (smi_sts & (1 << 18)) printk_debug("INTEL_USB2 "); + if (smi_sts & (1 << 17)) printk_debug("LEGACY_USB2 "); + if (smi_sts & (1 << 16)) printk_debug("SMBUS_SMI "); + if (smi_sts & (1 << 15)) printk_debug("SERIRQ_SMI "); + if (smi_sts & (1 << 14)) printk_debug("PERIODIC "); + if (smi_sts & (1 << 13)) printk_debug("TCO "); + if (smi_sts & (1 << 12)) printk_debug("DEVMON "); + if (smi_sts & (1 << 11)) printk_debug("MCSMI "); + if (smi_sts & (1 << 10)) printk_debug("GPI "); + if (smi_sts & (1 << 9)) printk_debug("GPE0 "); + if (smi_sts & (1 << 8)) printk_debug("PM1 "); + if (smi_sts & (1 << 6)) printk_debug("SWSMI_TMR "); + if (smi_sts & (1 << 5)) printk_debug("APM "); + if (smi_sts & (1 << 4)) printk_debug("SLP_SMI "); + if (smi_sts & (1 << 3)) printk_debug("LEGACY_USB "); + if (smi_sts & (1 << 2)) printk_debug("BIOS "); + printk_debug("\n"); +} + + +/** + * @brief read and clear GPE0_STS + * @return GPE0_STS register + */ +static u32 reset_gpe0_status(void) +{ + u32 reg32; + + reg32 = inl(pmbase + GPE0_STS); + /* set status bits are cleared by writing 1 to them */ + outl(reg32, pmbase + GPE0_STS); + + return reg32; +} + +static void dump_gpe0_status(u32 gpe0_sts) +{ + int i; + printk_debug("GPE0_STS: "); + for (i=31; i<= 16; i--) { + if (gpe0_sts & (1 << i)) printk_debug("GPIO%d ", (i-16)); + } + if (gpe0_sts & (1 << 14)) printk_debug("USB4 "); + if (gpe0_sts & (1 << 13)) printk_debug("PME_B0 "); + if (gpe0_sts & (1 << 12)) printk_debug("USB3 "); + if (gpe0_sts & (1 << 11)) printk_debug("PME "); + if (gpe0_sts & (1 << 10)) printk_debug("EL_SCI/BATLOW "); + if (gpe0_sts & (1 << 9)) printk_debug("PCI_EXP "); + if (gpe0_sts & (1 << 8)) printk_debug("RI "); + if (gpe0_sts & (1 << 7)) printk_debug("SMB_WAK "); + if (gpe0_sts & (1 << 6)) printk_debug("TCO_SCI "); + if (gpe0_sts & (1 << 5)) printk_debug("AC97 "); + if (gpe0_sts & (1 << 4)) printk_debug("USB2 "); + if (gpe0_sts & (1 << 3)) printk_debug("USB1 "); + if (gpe0_sts & (1 << 2)) printk_debug("HOT_PLUG "); + if (gpe0_sts & (1 << 0)) printk_debug("THRM "); + printk_debug("\n"); +} + + +/** + * @brief read and clear TCOx_STS + * @return TCOx_STS registers + */ +static u32 reset_tco_status(void) +{ + u32 tcobase = pmbase + 0x60; + u32 reg32; + + reg32 = inl(tcobase + 0x04); + /* set status bits are cleared by writing 1 to them */ + outl(reg32 & ~(1<<18), tcobase + 0x04); // Don't clear BOOT_STS before SECOND_TO_STS + if (reg32 & (1 << 18)) + outl(reg32 & (1<<18), tcobase + 0x04); // clear BOOT_STS + + return reg32; +} + + +static void dump_tco_status(u32 tco_sts) +{ + printk_debug("TCO_STS: "); + if (tco_sts & (1 << 20)) printk_debug("SMLINK_SLV "); + if (tco_sts & (1 << 18)) printk_debug("BOOT "); + if (tco_sts & (1 << 17)) printk_debug("SECOND_TO "); + if (tco_sts & (1 << 16)) printk_debug("INTRD_DET "); + if (tco_sts & (1 << 12)) printk_debug("DMISERR "); + if (tco_sts & (1 << 10)) printk_debug("DMISMI "); + if (tco_sts & (1 << 9)) printk_debug("DMISCI "); + if (tco_sts & (1 << 8)) printk_debug("BIOSWR "); + if (tco_sts & (1 << 7)) printk_debug("NEWCENTURY "); + if (tco_sts & (1 << 3)) printk_debug("TIMEOUT "); + if (tco_sts & (1 << 2)) printk_debug("TCO_INT "); + if (tco_sts & (1 << 1)) printk_debug("SW_TCO "); + if (tco_sts & (1 << 0)) printk_debug("NMI2SMI "); + printk_debug("\n"); +} + + +/* ********************* smi_util ************************* */ + +/* Data */ +#define UART_RBR 0x00 +#define UART_TBR 0x00 + +/* Control */ +#define UART_IER 0x01 +#define UART_IIR 0x02 +#define UART_FCR 0x02 +#define UART_LCR 0x03 +#define UART_MCR 0x04 +#define UART_DLL 0x00 +#define UART_DLM 0x01 + +/* Status */ +#define UART_LSR 0x05 +#define UART_MSR 0x06 +#define UART_SCR 0x07 + +static int uart_can_tx_byte(void) +{ + return inb(TTYS0_BASE + UART_LSR) & 0x20; +} + +static void uart_wait_to_tx_byte(void) +{ + while(!uart_can_tx_byte()) + ; +} + +static void uart_wait_until_sent(void) +{ + while(!(inb(TTYS0_BASE + UART_LSR) & 0x40)) + ; +} + +static void uart_tx_byte(unsigned char data) +{ + uart_wait_to_tx_byte(); + outb(data, TTYS0_BASE + UART_TBR); + /* Make certain the data clears the fifos */ + uart_wait_until_sent(); +} + +void console_tx_flush(void) +{ + uart_wait_to_tx_byte(); +} + +void console_tx_byte(unsigned char byte) +{ + if (byte == '\n') + uart_tx_byte('\r'); + uart_tx_byte(byte); +} + +/* We are using PCIe accesses for now + * 1. the chipset can do it + * 2. we don't need to worry about how we leave 0xcf8/0xcfc behind + */ +#include "../../../northbridge/intel/i945/pcie_config.c" + +/* ********************* smi_util ************************* */ + + +void io_trap_handler(int smif) +{ + u8 reg8; + global_nvs_t *gnvs = (global_nvs_t *)0xc00; + + printk_debug("SMI function trap 0x%x: ", smif); + + + switch (smif) { + case 0x32: + printk_debug("OS Init\n"); + break; + case 0xd6: + printk_debug("Get Brightness\n"); + outb(0x17, 0x66); + reg8 = inb(0x62); + gnvs->brtl = reg8; + break; + default: + printk_debug("Unknown function\n"); + break; + } + + /* On success, the IO Trap Handler returns 0 + * On failure, the IO Trap Handler returns a value != 0 + * + * For now, we force the return value to 0 and log all traps to + * see what's going on. + */ + //gnvs->smif = 0; +} + +/** + * @brief Set the EOS bit + */ +static void smi_set_eos(void) +{ + u8 reg8; + + reg8 = inb(pmbase + SMI_EN); + reg8 |= EOS; + outb(reg8, pmbase + SMI_EN); +} + +/** + * @brief Interrupt handler for SMI# + * + * @param smm_revision revision of the smm state save map + */ + +void smi_handler(u32 smm_revision) +{ + u8 reg8; + u16 pmctrl; + u16 pm1_sts; + u32 smi_sts, gpe0_sts, tco_sts; + unsigned int node; + smm_state_save_area_t state_save; + + /* Are we ok to execute the handler? */ + if (!smi_obtain_lock()) + return; + + node=nodeid(); + +#ifdef DEBUG_SMI + console_loglevel = DEFAULT_CONSOLE_LOGLEVEL; +#else + console_loglevel = 1; +#endif + + printk_debug("\nSMI# #%d\n", node); + + switch (smm_revision) { + case 0x00030007: + state_save.type = LEGACY; + state_save.legacy_state_save = (legacy_smm_state_save_area_t *) + (0xa8000 + 0x7e00 - (node * 0x400)); + break; + case 0x00030100: + state_save.type = EM64T; + state_save.em64t_state_save = (em64t_smm_state_save_area_t *) + (0xa8000 + 0x7d00 - (node * 0x400)); + break; + default: + printk_debug("smm_revision: 0x%08x\n", smm_revision); + printk_debug("SMI# not supported on your CPU\n"); + /* Don't release lock, so no further SMI will happen, + * if we don't handle it anyways. + */ + return; + } + + pmbase = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0x40) & 0xfffc; + printk_spew("SMI#: pmbase = 0x%04x\n", pmbase); + + /* We need to clear the SMI status registers, or we won't see what's + * happening in the following calls. + */ + smi_sts = reset_smi_status(); + dump_smi_status(smi_sts); + + if (smi_sts & (1 << 21)) { // MONITOR + global_nvs_t *gnvs = (global_nvs_t *)0xc00; + int i; + u32 reg32; + + reg32 = RCBA32(0x1e00); // TRSR - Trap Status Register +#if 0 + /* Comment in for some useful debug */ + for (i=0; i<4; i++) { + if (reg32 & (1 << i)) { + printk_debug(" io trap #%d\n", i); + } + } +#endif + RCBA32(0x1e00) = reg32; // TRSR + + reg32 = RCBA32(0x1e10); + + if ((reg32 & 0xfffc) != 0x808) { + printk_debug(" trapped io address = 0x%x\n", reg32 & 0xfffc); + printk_debug(" AHBE = %x\n", (reg32 >> 16) & 0xf); + printk_debug(" read/write: %s\n", (reg32 & (1 << 24)) ? "read" : + "write"); + } + + if (!(reg32 & (1 << 24))) { + /* Write Cycle */ + reg32 = RCBA32(0x1e18); + printk_debug(" iotrap written data = 0x%08x\n", reg32); + + } + + if (gnvs->smif) + io_trap_handler(gnvs->smif); // call function smif + } + + if (smi_sts & (1 << 13)) { // TCO + tco_sts = reset_tco_status(); + dump_tco_status(tco_sts); + + if (tco_sts & (1 << 8)) { // BIOSWR + u8 bios_cntl; + + bios_cntl = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc); + + if (bios_cntl & 1) { + /* BWE is RW, so the SMI was caused by a + * write to BWE, not by a write to the BIOS + */ + + /* This is the place where we notice someone + * is trying to tinker with the BIOS. We are + * trying to be nice and just ignore it. A more + * resolute answer would be to power down the + * box. + */ + printk_debug("Switching back to RO\n"); + pcie_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1)); + } /* No else for now? */ + } + } + + if (smi_sts & (1 << 8)) { // PM1 + pm1_sts = reset_pm1_status(); + dump_pm1_status(pm1_sts); + } + + if (smi_sts & (1 << 9)) { // GPE0 + gpe0_sts = reset_gpe0_status(); + dump_gpe0_status(gpe0_sts); + } + + if (smi_sts & (1 << 5)) { // APM + /* Emulate B2 register as the FADT / Linux expects it */ + + reg8 = inb(0xb2); + switch (reg8) { + case ACPI_DISABLE: + pmctrl = inw(pmbase + 0x04); + pmctrl |= (1 << 0); + outw(pmctrl, pmbase + 0x04); + printk_debug("SMI#: ACPI disabled.\n"); + break; + case ACPI_ENABLE: + pmctrl = inw(pmbase + 0x04); + pmctrl &= ~(1 << 0); + outw(pmctrl, pmbase + 0x04); + printk_debug("SMI#: ACPI enabled.\n"); + break; + } + } + + if (smi_sts & (1 << 4)) { // SLP_SMI + u32 reg32; + reg32 = inl(pmbase + 0x04); + printk_debug("SMI#: SLP = 0x%08x\n"); + printk_debug("SMI#: Powering off.\n"); + outl((6 << 10), pmbase + 0x04); + outl((1 << 13) | (6 << 10), pmbase + 0x04); + printk_debug("....\n"); + } + + + smi_release_lock(); + + /* De-assert SMI# signal to allow another SMI */ + smi_set_eos(); +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/smm.ld =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/smm.ld (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/smm.ld 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,53 @@ + +/* Maximum number of CPUs/cores */ +CPUS = 4; + +SECTIONS +{ + /* This is the actual SMM handler. + * + * We just put code, rodata, data and bss all in a row. + */ + . = 0xa0000; + .handler (.): { + /* Assembler stub */ + *(.handler) + + /* C code of the SMM handler */ + *(.text); + *(.text.*); + + /* C read-only data of the SMM handler */ + . = ALIGN(16); + *(.rodata) + *(.rodata.*) + + /* C read-write data of the SMM handler */ + . = ALIGN(4); + *(.data) + + /* C uninitialized data of the SMM handler */ + . = ALIGN(4); + *(.bss) + *(.sbss) + + /* What is this? */ + *(COMMON) + . = ALIGN(4); + } + + /* We are using the ASEG interleaved to stuff the SMM handlers + * for all CPU cores in there. The jump table redirects the execution + * to the actual SMM handler + */ + . = 0xa8000 - (( CPUS - 1) * 0x400); + .jumptable : { + *(.jumptable) + } + + /DISCARD/ : { + *(.comment) + *(.note) + *(.note.*) + } +}
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmhandler.S =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmhandler.S (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmhandler.S 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,201 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +/* NOTE: This handler assumes the SMM window goes from 0xa0000 + * to 0xaffff. In fact, at least on Intel Core CPUs (i945 chipset) + * the SMM window is 128K big, covering 0xa0000 to 0xbffff. + * So there is a lot of potential for growth in here. Let's stick + * to 64k if we can though. + */ + +/* + * +--------------------------------+ 0xaffff + * | Save State Map Node 0 | + * | Save State Map Node 1 | + * | Save State Map Node 2 | + * | Save State Map Node 3 | + * | ... | + * +--------------------------------+ 0xaf000 + * | | + * | | + * | | + * +--------------------------------+ 0xa8400 + * | SMM Entry Node 0 (+ stack) | + * +--------------------------------+ 0xa8000 + * | SMM Entry Node 1 (+ stack) | + * | SMM Entry Node 2 (+ stack) | + * | SMM Entry Node 3 (+ stack) | + * | ... | + * +--------------------------------+ 0xa7400 + * | | + * | SMM Handler | + * | | + * +--------------------------------+ 0xa0000 + * + */ + +#include <arch/asm.h> + +#define LAPIC_ID 0xfee00020 + +/* SMM_HANDLER_OFFSET is the 16bit offset within the ASEG + * at which smm_handler_start lives. At the moment the handler + * lives right at 0xa0000, so the offset is 0. + */ + +#define SMM_HANDLER_OFFSET 0x0000 + +/* initially SMM is some sort of real mode. Let gcc know + * how to treat the SMM handler stub + */ + +.section ".handler", "a", @progbits + +.code16 + +/** + * SMM code to enable protected mode and jump to the + * C-written function void smi_handler(u32 smm_revision) + * + * All the bad magic is not all that bad after all. + */ +smm_handler_start: + movw $(smm_gdtptr16 - smm_handler_start + SMM_HANDLER_OFFSET), %bx + data32 lgdt %cs:(%bx) + + movl %cr0, %eax + andl $0x7FFAFFD1, %eax /* PG,AM,WP,NE,TS,EM,MP = 0 */ + orl $0x60000001, %eax /* CD, NW, PE = 1 */ + movl %eax, %cr0 + + /* Enable protected mode */ + data32 ljmp $0x08, $1f + +.code32 +1: + /* Use flat data segment */ + movw $0x10, %ax + movw %ax, %ds + movw %ax, %es + movw %ax, %ss + movw %ax, %fs + movw %ax, %gs + + /* Get this CPU's LAPIC ID */ + movl $LAPIC_ID, %esi + movl (%esi), %ecx + shr $24, %ecx + + /* calculate stack offset by multiplying the APIC ID + * by 1024 (0x400), and save that offset in ebp. + */ + shl $10, %ecx + movl %ecx, %ebp + + /* We put the stack for each core right above + * its SMM entry point. Core 0 starts at 0xa8000, + * we spare 0x10 bytes for the jump to be sure. + */ + movl $0xa8010, %eax + subl %ecx, %eax /* subtract offset, see above */ + movl %eax, %ebx /* Save bottom of stack in ebx */ + +#define SMM_STACK_SIZE (0x400 - 0x10) + /* clear stack */ + cld + movl %eax, %edi + movl $(SMM_STACK_SIZE >> 2), %ecx + xorl %eax, %eax + rep stosl + + /* set new stack */ + addl $SMM_STACK_SIZE, %ebx + movl %ebx, %esp + + /* Get SMM revision */ + movl $0xa8000 + 0x7efc, %ebx /* core 0 address */ + subl %ebp, %ebx /* subtract core X offset */ + movl (%ebx), %eax + pushl %eax + + /* Call 32bit C handler */ + call smi_handler + + /* To return, just do rsm. It will "clean up" protected mode */ + rsm + +.code16 + +.align 4, 0xff + +smm_gdtptr16: + .word smm_gdt_end - smm_gdt - 1 + .long smm_gdt - smm_handler_start + 0xa0000 + SMM_HANDLER_OFFSET + +.code32 + +smm_gdt: + /* The first GDT entry can not be used. Keep it zero */ + .long 0x00000000, 0x00000000 + + /* gdt selector 0x08, flat code segment */ + .word 0xffff, 0x0000 + .byte 0x00, 0x9b, 0xcf, 0x00 /* G=1 and 0x0f, 4GB limit */ + + /* gdt selector 0x10, flat data segment */ + .word 0xffff, 0x0000 + .byte 0x00, 0x93, 0xcf, 0x00 + +smm_gdt_end: + + +.section ".jumptable", "a", @progbits + +/* This is the SMM jump table. All cores use the same SMM handler + * for simplicity. But SMM Entry needs to be different due to the + * save state area. The jump table makes sure all CPUs jump into the + * real handler on SMM entry. + */ + +/* This code currently supports up to 4 CPU cores. If more than 4 CPU cores + * shall be used, below table has to be updated, as well as smm.ld + */ + +/* GNU AS/LD will always generate code that assumes CS is 0xa000. In reality + * CS will be set to SMM_BASE[19:4] though. Knowing that the smm handler is the + * first thing in the ASEG, we do a far jump here, to set CS to 0xa000. + */ + +.code16 +jumptable: + /* core 3 */ + ljmp $0xa000, $SMM_HANDLER_OFFSET +.align 1024, 0x00 + /* core 2 */ + ljmp $0xa000, $SMM_HANDLER_OFFSET +.align 1024, 0x00 + /* core 1 */ + ljmp $0xa000, $SMM_HANDLER_OFFSET +.align 1024, 0x00 + /* core 0 */ + ljmp $0xa000, $SMM_HANDLER_OFFSET +.align 1024, 0x00 +
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmrelocate.S =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmrelocate.S (rev 0) +++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/smmrelocate.S 2008-10-29 04:46:52 UTC (rev 3701) @@ -0,0 +1,168 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 coresystems GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <arch/asm.h> +#include "../../../../src/northbridge/intel/i945/ich7.h" + +#undef DEBUG_SMM_RELOCATION +//#define DEBUG_SMM_RELOCATION + +#define LAPIC_ID 0xfee00020 + +.global smm_relocation_start +.global smm_relocation_end + +/* initially SMM is some sort of real mode. */ +.code16 + +/** + * This trampoline code relocates SMBASE to 0xa0000 - ( lapicid * 0x400 ) + * + * Why 0x400? It is a safe value to cover the save state area per CPU. On + * current AMD CPUs this area is _documented_ to be 0x200 bytes. On Intel + * Core 2 CPUs the _documented_ parts of the save state area is 48 bytes + * bigger, effectively sizing our data structures 0x300 bytes. + * + * LAPICID SMBASE SMM Entry SAVE STATE + * 0 0xa0000 0xa8000 0xafd00 + * 1 0x9fc00 0xa7c00 0xaf900 + * 2 0x9f800 0xa7800 0xaf500 + * 3 0x9f400 0xa7400 0xaf100 + * 4 0x9f000 0xa7000 0xaed00 + * 5 0x9ec00 0xa6c00 0xae900 + * 6 0x9e800 0xa6800 0xae500 + * 7 0x9e400 0xa6400 0xae100 + * 8 0x9e000 0xa6000 0xadd00 + * 9 0x9dc00 0xa5c00 0xad900 + * 10 0x9d800 0xa5800 0xad500 + * 11 0x9d400 0xa5400 0xad100 + * 12 0x9d000 0xa5000 0xacd00 + * 13 0x9cc00 0xa4c00 0xac900 + * 14 0x9c800 0xa4800 0xac500 + * 15 0x9c400 0xa4400 0xac100 + * . . . . + * . . . . + * . . . . + * 31 0x98400 0xa0400 0xa8100 + * + * With 32 cores, the SMM handler would need to fit between + * 0xa0000-0xa0400 and the stub plus stack would need to go + * at 0xa8000-0xa8100 (example for core 0). That is not enough. + * + * This means we're basically limited to 16 cpu cores before + * we need to use the TSEG/HSEG for the actual SMM handler plus stack. + * When we exceed 32 cores, we also need to put SMBASE to TSEG/HSEG. + * + * If we figure out the documented values above are safe to use, + * we could pack the structure above even more, so we could use the + * scheme to pack save state areas for 63 AMD CPUs or 58 Intel CPUs + * in the ASEG. + * + * Note: Some versions of Pentium M need their SMBASE aligned to 32k. + * On those the above only works for up to 2 cores. But for now we only + * care fore Core (2) Duo/Solo + * + */ + +smm_relocation_start: + /* Check revision to see if AMD64 style SMM_BASE + * Intel Core Solo/Duo: 0x30007 + * Intel Core2 Solo/Duo: 0x30100 + * AMD64: 0x3XX64 + * This check does not make much sense, unless someone ports + * SMI handling to AMD64 CPUs. + */ + + mov $0x38000 + 0x7efc, %ebx + addr32 mov (%ebx), %al + cmp $0x64, %al + je 1f + + mov $0x38000 + 0x7ef8, %ebx + jmp smm_relocate +1: + mov $0x38000 + 0x7f00, %ebx + +smm_relocate: + /* Get this CPU's LAPIC ID */ + movl $LAPIC_ID, %esi + addr32 movl (%esi), %ecx + shr $24, %ecx + + /* calculate offset by multiplying the + * apic ID by 1024 (0x400) + */ + movl %ecx, %edx + shl $10, %edx + + movl $0xa0000, %eax + subl %edx, %eax /* subtract offset, see above */ + + addr32 movl %eax, (%ebx) + + + /* The next section of code is hardware specific */ + + /* Clear SMI status */ + movw $(DEFAULT_PMBASE + 0x34), %dx + inw %dx, %ax + outw %ax, %dx + + /* Clear PM1 status */ + movw $(DEFAULT_PMBASE + 0x00), %dx + inw %dx, %ax + outw %ax, %dx + + /* Set EOS bit so other SMIs can occur */ + movw $(DEFAULT_PMBASE + 0x30), %dx + inl %dx, %eax + orl $(1 << 1), %eax + outl %eax, %dx + + /* End of hardware specific section. */ +#ifdef DEBUG_SMM_RELOCATION + /* print [SMM-x] so we can determine if CPUx went to SMM */ + movw $TTYS0_BASE, %dx + mov $'[', %al + outb %al, %dx + mov $'S', %al + outb %al, %dx + mov $'M', %al + outb %al, %dx + outb %al, %dx + movb $'-', %al + outb %al, %dx + /* calculate ascii of cpu number. More than 9 cores? -> FIXME */ + movb %cl, %al + addb $'0', %al + outb %al, %dx + mov $']', %al + outb %al, %dx + mov $'\r', %al + outb %al, %dx + mov $'\n', %al + outb %al, %dx +#endif + + /* That's it. return */ + rsm +smm_relocation_end: +