Author: rminnich Date: 2009-07-01 15:19:25 +0200 (Wed, 01 Jul 2009) New Revision: 4389
Modified: trunk/coreboot-v2/src/include/device/pci_ids.h trunk/coreboot-v2/src/mainboard/via/epia-n/Options.lb trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237r_lpc.c Log: I missed three files. Signed-off-by: Jon Harrison bothlyn@blueyonder.co.uk Acked-by: Ronald G. Minnich rminnich@gmail.com
Modified: trunk/coreboot-v2/src/include/device/pci_ids.h =================================================================== --- trunk/coreboot-v2/src/include/device/pci_ids.h 2009-07-01 12:26:11 UTC (rev 4388) +++ trunk/coreboot-v2/src/include/device/pci_ids.h 2009-07-01 13:19:25 UTC (rev 4389) @@ -1198,6 +1198,14 @@ #define PCI_DEVICE_ID_VIA_CN700_VLINK 0x7314 #define PCI_DEVICE_ID_VIA_CN700_BRIDGE 0xB198 #define PCI_DEVICE_ID_VIA_CN700_VGA 0x3344 +#define PCI_DEVICE_ID_VIA_CN400_AGP 0x0259 +#define PCI_DEVICE_ID_VIA_CN400_ERR 0x1259 +#define PCI_DEVICE_ID_VIA_CN400_HOST 0x2259 +#define PCI_DEVICE_ID_VIA_CN400_MEMCTRL 0x3259 +#define PCI_DEVICE_ID_VIA_CN400_PM 0x4259 +#define PCI_DEVICE_ID_VIA_CN400_VLINK 0x7259 +#define PCI_DEVICE_ID_VIA_CN400_BRIDGE 0xB198 +#define PCI_DEVICE_ID_VIA_CN400_VGA 0x3118
#define PCI_VENDOR_ID_SIEMENS 0x110A #define PCI_DEVICE_ID_SIEMENS_DSCC4 0x2102
Modified: trunk/coreboot-v2/src/mainboard/via/epia-n/Options.lb =================================================================== --- trunk/coreboot-v2/src/mainboard/via/epia-n/Options.lb 2009-07-01 12:26:11 UTC (rev 4388) +++ trunk/coreboot-v2/src/mainboard/via/epia-n/Options.lb 2009-07-01 13:19:25 UTC (rev 4389) @@ -58,7 +58,7 @@ uses CONFIG_HAVE_ACPI_RESUME uses CONFIG_CROSS_COMPILE uses CC -uses CONFIG_HOSTCC +uses HOSTCC uses CONFIG_OBJCOPY uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL @@ -108,7 +108,7 @@ default CONFIG_ROM_PAYLOAD = 1 default CONFIG_CROSS_COMPILE = "" default CC = "$(CROSS_COMPILE)gcc -m32 -fno-stack-protector" -default CONFIG_HOSTCC = "gcc" +default HOSTCC = "gcc" #default CONFIG_MAINBOARD = "EPIA-N"
##
Modified: trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237r_lpc.c =================================================================== --- trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237r_lpc.c 2009-07-01 12:26:11 UTC (rev 4388) +++ trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237r_lpc.c 2009-07-01 13:19:25 UTC (rev 4389) @@ -91,7 +91,7 @@
/* All delivered to CPU0. */ ioapic_table[0].value_high = (lapicid()) << (56 - 32); - l = (unsigned long *)ioapic_base; + l = (u32 *)ioapic_base;
/* Set APIC to FSB message bus. */ l[0] = 0x3; @@ -243,26 +243,56 @@ { u8 enables;
+ printk_spew("Entering vt8237r_init.\n"); + +#ifdef CONFIG_EPIA_VT8237R_INIT + printk_spew("vt8237r_init SATA LED.\n"); /* + * TODO: Looks like stock BIOS can do this but causes a hang * Enable SATA LED, disable special CPU Frequency Change - * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs. + * Setup to match EPIA default + * PCS0# on Pin U1 */ - pci_write_config8(dev, 0xe5, 0x9); + enables = pci_read_config8(dev, 0xe5); + enables |= 0x02; + pci_write_config8(dev, 0xe5, enables); + + printk_spew("vt8237r_init PCI Req.\n"); + /* + * Enable Flash Write Access. + * Note EPIA-N Does not use REQ5 or PCISTP#(Hang) + */ + enables = pci_read_config8(dev, 0xe4); + enables |= 0x2B; + pci_write_config8(dev, 0xe4, enables);
+#else + /* + * Enable SATA LED, disable special CPU Frequency Change - + * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs. + */ + pci_write_config8(dev, 0xe5, 0x09); + /* REQ5 as PCI request input - should be together with INTE-INTH. */ pci_write_config8(dev, 0xe4, 0x4); +#endif
+ + printk_spew("vt8237r_init CPU Rst.\n"); /* Set bit 3 of 0x4f (use INIT# as CPU reset). */ enables = pci_read_config8(dev, 0x4f); enables |= 0x08; pci_write_config8(dev, 0x4f, enables);
+ printk_spew("vt8237r_init Read Pass Write Ctrl.\n"); /* * Set Read Pass Write Control Enable * (force A2 from APIC FSB to low). */ pci_write_config8(dev, 0x48, 0x8c);
+ printk_spew("vt8237r_init calling southbridge_init_common.\n"); southbridge_init_common(dev);
/* FIXME: Intel needs more bit set for C2/C3. */ @@ -272,6 +302,8 @@ * Will work for C3 and for FID/VID change. */ outb(0x1, VT8237R_ACPI_IO_BASE + 0x11); + + printk_spew("Leaving vt8237r_init.\n"); }
static void vt8237s_init(struct device *dev)