Re: [LinuxBIOS] IDE become readonly, why?

[Russ Whitaker]

On Thu, 5 Apr 2007, Beneo wrote:
> Yes, see below:
>
> Beneo
>
> [root@(none) etc]# cat inittab
> #
> # inittab       This file describes how the INIT process should set up
> #               the system in a certain run-level.
> #
> # Author:       Miquel van Smoorenburg, 
> #               Modified for RHS Linux by Marc Ewing and Donnie Barnes
> #
>
> # Default runlevel. The runlevels used by RHS are:
> #   0 - halt (Do NOT set initdefault to this)
> #   1 - Single user mode
> #   2 - Multiuser, without NFS (The same as 3, if you do not have
> networking)
> #   3 - Full multiuser mode
> #   4 - unused
> #   5 - X11
> #   6 - reboot (Do NOT set initdefault to this)
> #
> #id:5:initdefault:
> id:3:initdefault:
>
> # System initialization.
> si::sysinit:/etc/rc.d/rc.sysinit
>
> l0:0:wait:/etc/rc.d/rc 0
> l1:1:wait:/etc/rc.d/rc 1
> l2:2:wait:/etc/rc.d/rc 2
> l3:3:wait:/etc/rc.d/rc 3
> l4:4:wait:/etc/rc.d/rc 4
> l5:5:wait:/etc/rc.d/rc 5
> l6:6:wait:/etc/rc.d/rc 6
>
> # Trap CTRL-ALT-DELETE
> ca::ctrlaltdel:/sbin/shutdown -t3 -r now
>
> # When our UPS tells us power has failed, assume we have a few minutes
> # of power left.  Schedule a shutdown for 2 minutes from now.
> # This does, of course, assume you have powerd installed and your
> # UPS connected and working correctly.
> pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down"
>
> # If power was restored before the shutdown kicked in, cancel it.
> pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled"
>
> # Run gettys in standard runlevels
> co:2345:respawn:/sbin/agetty ttyS0 115200 vt100
> 1:2345:respawn:/sbin/mingetty tty1
> 2:2345:respawn:/sbin/mingetty tty2
> 3:2345:respawn:/sbin/mingetty tty3
> 4:2345:respawn:/sbin/mingetty tty4
> 5:2345:respawn:/sbin/mingetty tty5
> 6:2345:respawn:/sbin/mingetty tty6
>
> ----- Original Message -----
> From: "Anton" 
> To: 
> Sent: Thursday, April 05, 2007 11:43 AM
> Subject: Re: [LinuxBIOS] IDE become readonly, why?
> > On Thu, 5 Apr 2007 11:27:11 -0700
> > "Beneo"  wrote:
> > > Hi all,
> > >
> > > I was using LinuxBIOS to boot Linux from IDE from a Broadcom HT,1000
> > > south bridge based  platform , I encounter an issue which is hard to
> > > understand. I hope somebody can give me some insight.
> > >
> > > During boot, Linux stoped at the point that it displayed a message:
> > > "Configuring kernel parameters:  [  OK  ]"
> > >
> > > then I pressed "CTRL-C",  Linux continue to boot, but display a message:
> > > "Starting automount:Cannot create temp file /tmp/autofs.meQYNM, could not
> > > make temp file"
> > >
> > > then Linux boot Skipped rest of initialization, like probe the network
> > > and etc. but Linux did give me a login prompt, I can login using root,
> > > but I cannot write any file at root directory, It appears to me Entire
> > > Linux file system becomes readonly.

It may, or may not, be the fault of linuxbios:
Things to check for hints:
    dmesg
    /var/log/sys

Usually the root file system is first mounted ro and the startup routine
checks the file system. If ok, root is then remounted rw. Slackware does
this in rc.S.

Did you edit any rc files? if so, you may have forgotten to chmod +x.

russ