On Thu, Oct 02, 2003 at 12:17:57PM -0600, ron minnich wrote:
Linux is now up. Tweak this, tweak that in southbridge and at some point it works. Looks like we needed some ISA config to make it go.
So V2 is up on the EPIA. Now if we can all come to closure on the config tool we'll be getting there :-)
This afternoon I will try to get the memory system to be sane.
Wow, this is fun, these little EPIAs are great cluster nodes. Small box, wrapped in steel so I can't break anything, powered by a wall wart. I love 'em.
Congrats, and thank you very much for the work!
If you don't know it yet, this might help debugging SPD stuff.. I just found a tool in lm-sensors, which decodes SPD bytes.
black:/usr/src/modules/lm-sensors/prog/eeprom$ ./decode-dimms.pl
PC DIMM Serial Presence Detect Tester/Decoder Written by Philip Edelbrock. Copyright 1998, 1999. Modified by Christian Zuckschwerdt zany@triq.net Version 2.6.3
Decoding EEPROM /proc/sys/dev/sensors/eeprom-i2c-1-50 Guessing DIMM is in bank 1
---=== The Following is Required Data and is Applicable to all DIMM Types ===--- # of bytes written to SDRAM EEPROM 128 Total number of bytes in EEPROM 256 Fundemental Memory type SDRAM Number of Row Address Bits (SDRAM only) 13 Number of Col Address Bits (SDRAM only) 10 Number of Module Rows 1 Data Width (SDRAM only) 64 Module Interface Signal Levels LVTTL Cycle Time (SDRAM) highest CAS latency 7.5ns Access Time (SDRAM) 5.4ns Module Configuration Type No Parity Refresh Type Self Refreshing Refresh Rate Reduced (7.8uS) Primary SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Primary SDRAM Component Widths 8 Error Checking SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Error Checking SDRAM Component Widths Undefined! Min Clock Delay for Back to Back Random Access 1
---=== The Following Apply to SDRAM DIMMs ONLY ===--- Burst lengths supported Burst Length = 1 Burst Length = 2 Burst Length = 4 Burst Length = 8 Burst Length = Page Number of Device Banks 4 Supported CAS Latencies CAS Latency = 2 CAS Latency = 3 Supported CS Latencies CS Latency = 0 Supported WE Latencies WE Latency = 0 SDRAM Module Attributes (None Reported) SDRAM Device Attributes (General) Supports Auto-Precharge Supports Precharge All Supports Write1/Read Burst Lower VCC Tolerance:10% Upper VCC Tolerance:10% SDRAM Cycle Time (2nd highest CAS) 7.5nS SDRAM Access from Clock Time (2nd highest CAS) 5.4nS
---=== The Following are Optional (may be Bogus) ===--- SDRAM Cycle Time (3rd highest CAS) Undefined! SDRAM Access from Clock Time (3rd highest CAS) Undefined!
---=== The Following are Required (for SDRAMs) ===--- Minumum Row Precharge Time 15nS Row Active to Row Active Min 15nS RAS to CAS Delay 15nS Min RAS Pulse Width 37nS
---=== The Following are Required and Apply to ALL DIMMs ===--- Row Densities 256 MByte
---=== The Following are Proposed and Apply to SDRAM DIMMs ===--- Command and Address Signal Setup Time 1.5nS Command and Address Signal Hold Time 0.8nS Data Signal Setup Time 1.5nS Data Signal Hold Time 0.8nS SPD Revision code 12 EEPROM Checksum of bytes 0-62 0x89 (verses calculated: 0x89) Manufacturer's JEDEC ID Code 0x0000000000000000 Manufacturer's JEDEC ID Code (" ") Manufacturing Location Code 0x00 Manufacurer's Part Number:" 32MX64U-133 32MX8 Revision Code 0x0000 Manufacturing Date 0x0000 Intel Specification for Frequency 100MHz Intel Spec Details for 100MHz Support CAS Latency = 2 CAS Latency = 3 Junction Temp B (100 degrees C) CLK 3 Connected CLK 2 Connected CLK 1 Connected CLK 0 Connected Double Sided DIMM Number of SDRAM DIMMs detected and decoded 1
Try './decode-dimms.pl --format' for html output. black:/usr/src/modules/lm-sensors/prog/eeprom$