Am Mittwoch, 17. Oktober 2007 14:14:17 schrieb Carl-Daniel Hailfinger:
On 15.10.2007 01:28, Harald Gutmann wrote:
Am Montag, 15. Oktober 2007 01:06:00 schrieb Carl-Daniel Hailfinger:
Great, thanks! The code I have also is not polished, so even if your code is ugly, it is better than no code. We can clean up that stuff together.
yes, that's right! here it is.
the patch is done with: Revision: 2850
I have rearranged some code, so your patch does no longer apply, but it should be easy to fix.
fine!
diff -ubrN ../../flashrom.original/board_enable.c flashrom.new/board_enable.c --- ../../flashrom.original/board_enable.c 2007-10-15 01:14:29.000000000 +0200 +++ flashrom.new/board_enable.c 2007-10-14 20:28:41.000000000 +0200
This is now in spi.c
@@ -37,7 +37,7 @@ #define JEDEC_RDID_OUTSIZE 0x01 #define JEDEC_RDID_INSIZE 0x03
-static uint16_t it8716f_flashport = 0; +uint16_t it8716f_flashport = 0;
/* Generic Super I/O helper functions */ uint8_t regval(uint16_t port, uint8_t reg) @@ -111,7 +111,7 @@ whereas the IT8716F splits commands internally into address and non-address commands with the address in inverse wire order. That's why the register ordering in case 4 and 5 may seem strange. */ -static int it8716f_spi_command(uint16_t port, unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr) +int it8716f_spi_command(uint16_t port, unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr) { uint8_t busy, writeenc; do { diff -ubrN ../../flashrom.original/board_enable.h flashrom.new/board_enable.h --- ../../flashrom.original/board_enable.h 1970-01-01 01:00:00.000000000 +0100 +++ flashrom.new/board_enable.h 2007-10-14 21:09:18.000000000 +0200
Perhaps move to spi.h?
@@ -0,0 +1,7 @@ +#ifndef boardenableh +#define boardenableh +uint16_t it8716f_flashport; +uint8_t regval(uint16_t port, uint8_t reg); +void regwrite(uint16_t port, uint8_t reg, uint8_t val); +int it8716f_spi_command(uint16_t port, unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr); +#endif diff -ubrN ../../flashrom.original/flashchips.c flashrom.new/flashchips.c --- ../../flashrom.original/flashchips.c 2007-10-15 01:14:28.000000000 +0200 +++ flashrom.new/flashchips.c 2007-10-15 01:24:58.000000000 +0200 @@ -39,7 +39,7 @@ {"Mx29f002", MX_ID, MX_29F002, 256, 64 * 1024, probe_29f002, erase_29f002, write_29f002}, {"MX25L4005", MX_ID, MX_25L4005, 512, 4 * 1024,
probe_spi, NULL, NULL},
probe_spi, erase_25l4005, write_25l4005},OK
diff -ubrN ../../flashrom.original/flash.h flashrom.new/flash.h --- ../../flashrom.original/flash.h 2007-10-15 01:14:28.000000000 +0200 +++ flashrom.new/flash.h 2007-10-14 19:13:52.000000000 +0200 @@ -294,4 +294,10 @@ /* w49f002u.c */ int write_49f002(struct flashchip *flash, uint8_t *buf);
+/* mx25l4005.c */ +// probe
the "//probe" could be deleted.
+int write_25l4005(struct flashchip *flash, uint8_t *buf); +int erase_25l4005(struct flashchip *flash); +int read_25l4005(struct flashchip *flash, uint8_t *buf);
#endif /* !__FLASH_H__ */
OK
diff -ubrN ../../flashrom.original/Makefile flashrom.new/Makefile --- ../../flashrom.original/Makefile 2007-10-15 01:14:29.000000000 +0200 +++ flashrom.new/Makefile 2007-10-15 01:20:16.000000000 +0200 @@ -24,7 +24,7 @@ am29f040b.o mx29f002.o sst39sf020.o m29f400bt.o w49f002u.o \ 82802ab.o msys_doc.o pm49fl004.o sst49lf040.o sst49lfxxxc.o \ sst_fwhub.o layout.o lbtable.o flashchips.o flashrom.o \
- sharplhf00l04.o w29ee011.o
- sharplhf00l04.o w29ee011.o mx25l4005.o
all: pciutils dep $(PROGRAM)
@@ -33,7 +33,7 @@ $(STRIP) $(STRIP_ARGS) $(PROGRAM)
clean:
- rm -f *.o *~
- rm -f *.o *~ flashrom
distclean: clean rm -f $(PROGRAM) .dependencies
Skip the make clean changes. We have make distclean.
like mentioned it's in distclean.
diff -ubrN ../../flashrom.original/mx25l4005.c flashrom.new/mx25l4005.c --- ../../flashrom.original/mx25l4005.c 1970-01-01 01:00:00.000000000 +0100 +++ flashrom.new/mx25l4005.c 2007-10-15 01:17:56.000000000 +0200 @@ -0,0 +1,57 @@ +#include <stdint.h> +#include <stdlib.h> +#include <stdio.h> +#include "flash.h" +#include "board_enable.h"
+static void check_n_write_enable() {
- uint8_t result[3] = {0, 0, 0};
- uint8_t command[5] = {0x06, 0, 0, 0, 0};
- // Send WREN (Write Enable)
- it8716f_spi_command(it8716f_flashport, 1, 0, command, result);
generic_spi_command
- uint8_t reg=regval(it8716f_flashport,0x24);
- reg|=(1<<4);
- regwrite(it8716f_flashport,0x24,reg);
I have absolutely no idea what you are trying to do here. According to my data sheet, your code does the following:
- Enable multiple byte mode, set clock to 33/2 MHz, read the last JEDEC
command sent to the flash chip
- Set bit 4 of the last JEDEC command
- Enable multiple byte mode, set clock to 33/2 MHz, write the modified
JEDEC command
sry, i also don't know exactly, a friend of mine hacked that (and i just have started to learn c.) and like told the code was hacked in little time, but worked.
Please note that none of these three lines send or receive anything from/to the chip.
+}
+static void write_disable() {
- uint8_t result[3] = {0, 0, 0};
- uint8_t command[5] = {0x04, 0, 0, 0, 0};
- // Send WRDI (Write Disable)
- it8716f_spi_command(it8716f_flashport, 1, 0, command, result);
generic_spi_command
- uint8_t reg=regval(it8716f_flashport,0x24);
- reg&=~(1<<4);
- regwrite(it8716f_flashport,0x24,reg);
Same as above: What are you trying to do?
same as above: i don't know.
+}
+void write256b(int block, uint8_t *buf, uint8_t *bios ) {
- check_n_write_enable();
- outb(0x06,it8716f_flashport+1);
- outb((3<<4),it8716f_flashport);
- int i;
- for (i=0;i<256;++i) {
bios[256*block+i]=buf[256*block+i];- }
this splitting is because of the superIO and not of the spi chip programmend. look at the end of the message. (*)
- outb(0,it8716f_flashport);
- write_disable();
- usleep (1000);
Check the chip status register instead fo waiting.
we tried that before, but it didn't work for any reason, but i don't know what the problem was, but the first working result was with the hardcoded sleep.
+}
OK, but we probably need a generic_spi_command_prepare and generic_spi_command_stop
+int write_25l4005(struct flashchip *flash, uint8_t *buf) {
- int total_size=1024*flash->total_size;
- int i;
- for (i=0;i<total_size/256;++i) {
write256b(i, buf, (uint8_t*)flash->virtual_memory);- }
+return 0; +}
OK
+int erase_25l4005(struct flashchip *flash) { +check_n_write_enable(); +uint8_t result[3]={0, 0, 0}; +uint8_t command[5]={0xc7, 0, 0, 0, 0}; +it8716f_spi_command(it8716f_flashport, 1, 0, command, result);
generic_spi_command
+write_disable(); +sleep (3); +// the chip needs some time, until it responses again. +return 0;
Can you instead read the flash chip status register in a loop? That way, you don't have to hardcode the sleep duration.
would be better.
+}
Overall, I like it.
My version of the write patch follows. Please test.
tested and approved to work!
(*) but just another thing: it would be good not to fix that code just for the MX25L4005 chip, because there are much more other chips out which can be programmed the same way. for the chip it was originally written, it works and that's really fine!
regards, harald
Index: flash.h
--- flash.h (Revision 2864) +++ flash.h (Arbeitskopie) @@ -296,4 +296,10 @@ /* w49f002u.c */ int write_49f002(struct flashchip *flash, uint8_t *buf);
+/* mx25l4005.c */ +// probe +int write_25l4005(struct flashchip *flash, uint8_t *buf); +int erase_25l4005(struct flashchip *flash); +int read_25l4005(struct flashchip *flash, uint8_t *buf);
#endif /* !__FLASH_H__ */ Index: flashchips.c =================================================================== --- flashchips.c (Revision 2864) +++ flashchips.c (Arbeitskopie) @@ -39,7 +39,7 @@ {"Mx29f002", MX_ID, MX_29F002, 256, 64 * 1024, probe_29f002, erase_29f002, write_29f002}, {"MX25L4005", MX_ID, MX_25L4005, 512, 4 * 1024,
probe_spi, NULL, NULL},
probe_spi, erase_25l4005, write_25l4005},Index: spi.c
--- spi.c (Revision 2864) +++ spi.c (Arbeitskopie) @@ -34,8 +34,16 @@ #define JEDEC_RDID_OUTSIZE 0x01 #define JEDEC_RDID_INSIZE 0x03
-static uint16_t it8716f_flashport = 0; +#define JEDEC_WREN {0x06} +#define JEDEC_WREN_OUTSIZE 0x01 +#define JEDEC_WREN_INSIZE 0x00
+#define JEDEC_WRDI {0x04} +#define JEDEC_WRDI_OUTSIZE 0x01 +#define JEDEC_WRDI_INSIZE 0x00
+uint16_t it8716f_flashport = 0;
/* Generic Super I/O helper functions */ uint8_t regval(uint16_t port, uint8_t reg) { @@ -170,7 +178,7 @@ return 0; }
-static int generic_spi_command(unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr) +int generic_spi_command(unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr) { if (it8716f_flashport) return it8716f_spi_command(it8716f_flashport, writecnt, readcnt, writearr, readarr); @@ -188,6 +196,25 @@ return 0; }
+void generic_spi_write_enable() +{
- const unsigned char cmd[] = JEDEC_WREN;
- unsigned char result[] = {0, 0, 0};
- // Send WREN (Write Enable)
- generic_spi_command(JEDEC_WREN_OUTSIZE, JEDEC_WREN_INSIZE, cmd, result);
+}
+void generic_spi_write_disable() +{
- const unsigned char cmd[] = JEDEC_WRDI;
- unsigned char result[] = {0, 0, 0};
- // Send WRDI (Write Disable)
- generic_spi_command(JEDEC_WRDI_OUTSIZE, JEDEC_WRDI_INSIZE, cmd, result);
+}
int probe_spi(struct flashchip *flash) { unsigned char readarr[3]; Index: Makefile =================================================================== --- Makefile (Revision 2864) +++ Makefile (Arbeitskopie) @@ -24,7 +24,7 @@ am29f040b.o mx29f002.o sst39sf020.o m29f400bt.o w49f002u.o \ 82802ab.o msys_doc.o pm49fl004.o sst49lf040.o sst49lfxxxc.o \ sst_fwhub.o layout.o lbtable.o flashchips.o flashrom.o \
- sharplhf00l04.o w29ee011.o spi.o
- sharplhf00l04.o w29ee011.o spi.o mx25l4005.o
all: pciutils dep $(PROGRAM)
Index: spi.h
--- spi.h (Revision 0) +++ spi.h (Revision 0) @@ -0,0 +1,9 @@ +#ifndef __SPI_H__ +#define __SPI_H__ 1
+uint16_t it8716f_flashport; +int generic_spi_command(unsigned char writecnt, unsigned char readcnt, const unsigned char *writearr, unsigned char *readarr); +void generic_spi_write_enable(); +void generic_spi_write_disable();
+#endif Index: mx25l4005.c =================================================================== --- mx25l4005.c (Revision 0) +++ mx25l4005.c (Revision 0) @@ -0,0 +1,39 @@ +#include <stdint.h> +#include <stdlib.h> +#include <stdio.h> +#include "flash.h" +#include "spi.h"
+void write256b(int block, uint8_t *buf, uint8_t *bios ) {
- generic_spi_write_enable();
- outb(0x06,it8716f_flashport+1);
- outb((3<<4),it8716f_flashport);
- int i;
- for (i=0;i<256;++i) {
bios[256*block+i]=buf[256*block+i];- }
- outb(0,it8716f_flashport);
- generic_spi_write_disable();
- usleep (1000);
+}
+int write_25l4005(struct flashchip *flash, uint8_t *buf) {
- int total_size=1024*flash->total_size;
- int i;
- for (i=0;i<total_size/256;++i) {
write256b(i, buf, (uint8_t*)flash->virtual_memory);- }
+return 0; +}
+int erase_25l4005(struct flashchip *flash) {
- generic_spi_write_enable();
- uint8_t result[3]={0, 0, 0};
- uint8_t command[5]={0xc7, 0, 0, 0, 0};
- generic_spi_command(1, 0, command, result);
- generic_spi_write_disable();
- // the chip needs some time, until it responses again.
- sleep (3);
- return 0;
+}