Ronald G. Minnich (rminnich@gmail.com) just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/2223
-gerrit
commit 8d2fb5c0c99632da1b8009f7a7d45b05a92b43a0 Author: Ronald G. Minnich rminnich@gmail.com Date: Tue Jan 29 14:31:33 2013 -0800
Exynos5250: change all unsigned with no type to 'unsigned int'
At some point we did a lot of cleanup to replace bare 'unsigned' with 'unsigned int'. Do that work for this imported code as well.
At some point, we may find we can shrink these 'int's to something smaller, thought I very much doubt it's worth the trouble.
Change-Id: Ic3da491c0188c56c836f8b9c4c8f26a31b4b3573 Signed-off-by: Ronald G. Minnich rminnich@gmail.com --- src/cpu/samsung/exynos5250/clock_init.h | 66 ++++++++++++++++----------------- 1 file changed, 33 insertions(+), 33 deletions(-)
diff --git a/src/cpu/samsung/exynos5250/clock_init.h b/src/cpu/samsung/exynos5250/clock_init.h index 57a0fe6..00561a0 100644 --- a/src/cpu/samsung/exynos5250/clock_init.h +++ b/src/cpu/samsung/exynos5250/clock_init.h @@ -31,27 +31,27 @@ enum {
/* These are the ratio's for configuring ARM clock */ struct arm_clk_ratios { - unsigned arm_freq_mhz; /* Frequency of ARM core in MHz */ - - unsigned apll_mdiv; - unsigned apll_pdiv; - unsigned apll_sdiv; - - unsigned arm2_ratio; - unsigned apll_ratio; - unsigned pclk_dbg_ratio; - unsigned atb_ratio; - unsigned periph_ratio; - unsigned acp_ratio; - unsigned cpud_ratio; - unsigned arm_ratio; + unsigned int arm_freq_mhz; /* Frequency of ARM core in MHz */ + + unsigned int apll_mdiv; + unsigned int apll_pdiv; + unsigned int apll_sdiv; + + unsigned int arm2_ratio; + unsigned int apll_ratio; + unsigned int pclk_dbg_ratio; + unsigned int atb_ratio; + unsigned int periph_ratio; + unsigned int acp_ratio; + unsigned int cpud_ratio; + unsigned int arm_ratio; };
/* These are the memory timings for a particular memory type and speed */ struct mem_timings { enum mem_manuf mem_manuf; /* Memory manufacturer */ enum ddr_mode mem_type; /* Memory type */ - unsigned frequency_mhz; /* Frequency of memory in MHz */ + unsigned int frequency_mhz; /* Frequency of memory in MHz */
/* Here follow the timing parameters for the selected memory */ uint8_t apll_mdiv; @@ -77,18 +77,18 @@ struct mem_timings { uint8_t bpll_sdiv; uint8_t use_bpll; /* 1 to use BPLL for cdrex, 0 to use MPLL */ uint8_t pclk_cdrex_ratio; - unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT]; + unsigned int direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
- unsigned timing_ref; - unsigned timing_row; - unsigned timing_data; - unsigned timing_power; + unsigned int timing_ref; + unsigned int timing_row; + unsigned int timing_data; + unsigned int timing_power;
/* DQS, DQ, DEBUG offsets */ - unsigned phy0_dqs; - unsigned phy1_dqs; - unsigned phy0_dq; - unsigned phy1_dq; + unsigned int phy0_dqs; + unsigned int phy1_dqs; + unsigned int phy0_dq; + unsigned int phy1_dq; uint8_t phy0_tFS; uint8_t phy1_tFS; uint8_t phy0_pulld_dqs; @@ -116,21 +116,21 @@ struct mem_timings { uint8_t zq_mode_term; uint8_t zq_mode_noterm; /* 1 to allow termination disable */
- unsigned memcontrol; - unsigned memconfig; + unsigned int memcontrol; + unsigned int memconfig;
- unsigned membaseconfig0; - unsigned membaseconfig1; - unsigned prechconfig_tp_cnt; - unsigned dpwrdn_cyc; - unsigned dsref_cyc; - unsigned concontrol; + unsigned int membaseconfig0; + unsigned int membaseconfig1; + unsigned int prechconfig_tp_cnt; + unsigned int dpwrdn_cyc; + unsigned int dsref_cyc; + unsigned int concontrol; /* Channel and Chip Selection */ uint8_t dmc_channels; /* number of memory channels */ uint8_t chips_per_channel; /* number of chips per channel */ uint8_t chips_to_configure; /* number of chips to configure */ uint8_t send_zq_init; /* 1 to send this command */ - unsigned impedance; /* drive strength impedeance */ + unsigned int impedance; /* drive strength impedeance */ uint8_t gate_leveling_enable; /* check gate leveling is enabled */ };