Can you please post a patch with all your changes to the code or config files (if any) and a full boot log (get it via serial console) with maximum debug level enabled?
And/or can you try with another PCI VGA card to see if it makes a difference?
Thanks, Uwe.
Well, I dug up an ancient ATI card and installed it with similar results as when using my GForce 8600 card. For some reason X refuses to start. I have attached my FILO Config file, my LinuxBIOS2 Config.lb file, the boot output from the serial port, and the Xorg log.
Also, two observations: 1. I tried to use a 20 year old dumb terminal (NABU 4503) to monitor serial output. The terminal could only handle a maximum of 19200 baud which was too slow for LinuxBIOS output stream - all characters were garbled. Once FILO took over the output was readable. Anyway I scrapped the terminal and now use a PC with minicom at 115200 baud. 2. Kernel loading is slow but initrd loading is very, very, slow.
John ===============
# Use grub instead of autoboot? USE_GRUB = 1 # Grub menu.lst path # hde is filo for sda (1st sata drive) MENULST_FILE = "hde3:/boot/grub/lbmenu.lst" # Driver for hard disk, CompactFlash, and CD-ROM on IDE bus IDE_DISK = 1 # Add a short delay when polling status registers # (required on some broken SATA controllers) IDE_DISK_POLL_DELAY = 1 # Driver for USB Storage USB_DISK = 1 # VGA text console VGA_CONSOLE = 1 PC_KEYBOARD = 1 # Enable the serial console SERIAL_CONSOLE = 1 # Serial console; real external serial port SERIAL_IOBASE = 0x3f8 # SERIAL_SPEED = 19200 # Filesystems FSYS_EXT2FS = 1 # FSYS_REISERFS = 1 # FSYS_ISO9660 = 1 # Support for boot disk image in bootable CD-ROM (El Torito) # ELTORITO = 1 # PCI support SUPPORT_PCI = 1 # Enable this to scan PCI busses above bus 0 # AMD64 based boards do need this. PCI_BRUTE_SCAN = 1 # Loader for standard Linux kernel image, a.k.a. /vmlinuz LINUX_LOADER = 1
## ## This file is part of the LinuxBIOS project. ## ## Copyright (C) 2007 AMD ## Written by Yinghai Lu yinghailu@gmail.com for AMD. ## ## This program is free software; you can redistribute it and/or modify ## it under the terms of the GNU General Public License as published by ## the Free Software Foundation; either version 2 of the License, or ## (at your option) any later version. ## ## This program is distributed in the hope that it will be useful, ## but WITHOUT ANY WARRANTY; without even the implied warranty of ## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ## GNU General Public License for more details. ## ## You should have received a copy of the GNU General Public License ## along with this program; if not, write to the Free Software ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ##
target m57sli mainboard gigabyte/m57sli
romimage "normal" option CONFIG_CONSOLE_VGA=1 option CONFIG_PCI_ROM_RUN=1 option USE_FAILOVER_IMAGE=0 option USE_FALLBACK_IMAGE=0 option ROM_IMAGE_SIZE=0x20000 option XIP_ROM_SIZE=0x40000 option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" # Enable the Serial Console option CONFIG_CONSOLE_SERIAL8250=1 # option TTYS0_BAUD=19200 # Select the serial console base port option TTYS0_BASE=0x3f8 # This defaults to 8 data bits, 1 stop bit, and no parity option TTYS0_LCS=0x3 payload ../../../payloads/filo.elf end
romimage "fallback" option CONFIG_CONSOLE_VGA=1 option CONFIG_PCI_ROM_RUN=1 option USE_FAILOVER_IMAGE=0 option USE_FALLBACK_IMAGE=1 option ROM_IMAGE_SIZE=0x20000 option XIP_ROM_SIZE=0x40000 option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" payload ../../../payloads/filo.elf end
romimage "failover" option USE_FAILOVER_IMAGE=1 option USE_FALLBACK_IMAGE=0 option ROM_IMAGE_SIZE=FAILOVER_SIZE option XIP_ROM_SIZE=FAILOVER_SIZE option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover" end
#buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback" buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback" "failover"
LinuxBIOS-2.0.0_m57sli_Fallback Tue Jul 24 12:07:33 EDT 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3104121204160202 end msr fid, vid 3104120404160216 mcp55_num:01 ht reset -
LinuxBIOS-2.0.0_m57sli_Fallback Tue Jul 24 12:07:33 EDT 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3104120404160216 end msr fid, vid 3104120404160216 mcp55_num:01 Ram1.00 Ram2.00 Unbuffered 400Mhz Interleaved RAM: 0x00400000 KB Ram3 dimm_mask = 00000033 x4_mask = 00000000 x16_mask = 00000000 single_rank_mask = 00000000 ODC = 00113322 Addr Timing= 00202520 Initializing memory: done RAM: 0x00500000 KB Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB Setting variable MTRR 3, base: 2048MB, range: 1024MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=1d done set DQS timing:DQSPos: 00 done set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=34 done Total DQS Training : tsc [00]=00000000562bc080 Total DQS Training : tsc [01]=0000000058a567ea Total DQS Training : tsc [02]=000000012eb2bd1a Total DQS Training : tsc [03]=0000000130f9f9b2 Ram4 v_esp=000ceeb8 testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying LinuxBIOS to RAM. src=fffdf000 dst=00100000 linxbios_ram.nrv2b length = 0000d5d4 linxbios_ram.bin length = 000225b0 Jumping to LinuxBIOS. LinuxBIOS-2.0.0_m57sli_Fallback Tue Jul 24 12:07:33 EDT 2007 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled PCI: 00:18.3 siblings=1 CPU: APIC: 00 enabled CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 00 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:00.0 [10de/0369] enabled PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010 PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [10de/0369] enabled PCI: 00:01.0 [10de/0360] enabled PCI: 00:01.1 [10de/0368] enabled PCI: 00:01.2 [10de/036a] enabled PCI: 00:01.3 [10de/036b] enabled PCI: 00:02.0 [10de/036c] enabled PCI: 00:02.1 [10de/036d] enabled PCI: 00:04.0 [10de/036e] enabled PCI: 00:05.0 [10de/037f] enabled PCI: 00:05.1 [10de/037f] enabled PCI: 00:05.2 [10de/037f] enabled PCI: 00:06.0 [10de/0370] enabled PCI: 00:06.1 [10de/0371] enabled PCI: 00:08.0 [10de/0373] enabled PCI: 00:0a.0 [10de/0376] enabled PCI: 00:0b.0 [10de/0374] enabled PCI: 00:0c.0 [10de/0374] enabled PCI: 00:0d.0 [10de/0378] enabled PCI: 00:0e.0 [10de/0375] enabled PCI: 00:0f.0 [10de/0377] enabled PNP: 002e.0 disabled PNP: 002e.1 enabled PNP: 002e.2 disabled PNP: 002e.3 disabled PNP: 002e.4 enabled PNP: 002e.5 enabled PNP: 002e.6 enabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled PCI: pci_scan_bus for bus 01 PCI: pci_scan_bus returning with max=001 PCI: pci_scan_bus for bus 02 PCI: pci_scan_bus returning with max=002 PCI: pci_scan_bus for bus 03 PCI: pci_scan_bus returning with max=003 PCI: pci_scan_bus for bus 04 PCI: pci_scan_bus returning with max=004 PCI: pci_scan_bus for bus 05 PCI: pci_scan_bus returning with max=005 PCI: pci_scan_bus for bus 06 PCI: pci_scan_bus returning with max=006 PCI: pci_scan_bus for bus 07 PCI: 07:00.0 [10de/0400] enabled PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 done Allocating resources... Reading resources... PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 02 io PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 02 mem PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem Done reading resources. Allocating VGA resource PCI: 07:00.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0f.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] io <node 0 link 0> PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] prefmem <node 0 link 0> PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f71fffff] mem <node 0 link 0> PCI: 00:01.0 14 <- [0x00f7144000 - 0x00f7144fff] mem PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] io PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] io PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] irq PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq PCI: 00:01.1 10 <- [0x0000002c00 - 0x0000002c3f] io PCI: 00:01.1 20 <- [0x0000002c40 - 0x0000002c7f] io PCI: 00:01.1 24 <- [0x0000002c80 - 0x0000002cbf] io PCI: 00:01.1 60 <- [0x0000002000 - 0x00000020ff] io PCI: 00:01.1 64 <- [0x0000002400 - 0x00000024ff] io PCI: 00:01.1 68 <- [0x0000002800 - 0x00000028ff] io PCI: 00:01.3 10 <- [0x00f7100000 - 0x00f713ffff] mem PCI: 00:02.0 10 <- [0x00f7145000 - 0x00f7145fff] mem PCI: 00:02.1 10 <- [0x00f714a000 - 0x00f714a0ff] mem PCI: 00:04.0 20 <- [0x0000002cc0 - 0x0000002ccf] io PCI: 00:05.0 10 <- [0x0000003000 - 0x0000003007] io PCI: 00:05.0 14 <- [0x0000003070 - 0x0000003073] io PCI: 00:05.0 18 <- [0x0000003010 - 0x0000003017] io PCI: 00:05.0 1c <- [0x0000003080 - 0x0000003083] io PCI: 00:05.0 20 <- [0x0000002cd0 - 0x0000002cdf] io PCI: 00:05.0 24 <- [0x00f7146000 - 0x00f7146fff] mem PCI: 00:05.1 10 <- [0x0000003020 - 0x0000003027] io PCI: 00:05.1 14 <- [0x0000003090 - 0x0000003093] io PCI: 00:05.1 18 <- [0x0000003030 - 0x0000003037] io PCI: 00:05.1 1c <- [0x00000030a0 - 0x00000030a3] io PCI: 00:05.1 20 <- [0x0000002ce0 - 0x0000002cef] io PCI: 00:05.1 24 <- [0x00f7147000 - 0x00f7147fff] mem PCI: 00:05.2 10 <- [0x0000003040 - 0x0000003047] io PCI: 00:05.2 14 <- [0x00000030b0 - 0x00000030b3] io PCI: 00:05.2 18 <- [0x0000003050 - 0x0000003057] io PCI: 00:05.2 1c <- [0x00000030c0 - 0x00000030c3] io PCI: 00:05.2 20 <- [0x0000002cf0 - 0x0000002cff] io PCI: 00:05.2 24 <- [0x00f7148000 - 0x00f7148fff] mem PCI: 00:06.1 10 <- [0x00f7140000 - 0x00f7143fff] mem PCI: 00:08.0 10 <- [0x00f7149000 - 0x00f7149fff] mem PCI: 00:08.0 14 <- [0x0000003060 - 0x0000003067] io PCI: 00:08.0 18 <- [0x00f714b000 - 0x00f714b0ff] mem PCI: 00:08.0 1c <- [0x00f714c000 - 0x00f714c00f] mem PCI: 00:0f.0 1c <- [0x0000001000 - 0x0000001fff] bus 07 io PCI: 00:0f.0 24 <- [0x00e0000000 - 0x00efffffff] bus 07 prefmem PCI: 00:0f.0 20 <- [0x00f4000000 - 0x00f70fffff] bus 07 mem PCI: 07:00.0 10 <- [0x00f6000000 - 0x00f6ffffff] mem PCI: 07:00.0 14 <- [0x00e0000000 - 0x00efffffff] prefmem64 PCI: 07:00.0 1c <- [0x00f4000000 - 0x00f5ffffff] mem64 PCI: 07:00.0 24 <- [0x0000001000 - 0x000000107f] io PCI: 07:00.0 30 <- [0x00f7000000 - 0x00f701ffff] romem PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 140 PCI: 00:00.0 subsystem <- 1022/2b80 PCI: 00:00.0 cmd <- 146 PCI: 00:01.0 subsystem <- 1022/2b80 PCI: 00:01.0 cmd <- 14f mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297 mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237 mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060 mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064 PCI: 00:01.1 subsystem <- 1022/2b80 PCI: 00:01.1 cmd <- 141 PCI: 00:01.2 cmd <- 540 PCI: 00:01.3 cmd <- 142 PCI: 00:02.0 subsystem <- 1022/2b80 PCI: 00:02.0 cmd <- 142 PCI: 00:02.1 subsystem <- 1022/2b80 PCI: 00:02.1 cmd <- 142 PCI: 00:04.0 subsystem <- 1022/2b80 PCI: 00:04.0 cmd <- 141 PCI: 00:05.0 subsystem <- 1022/2b80 PCI: 00:05.0 cmd <- 143 PCI: 00:05.1 subsystem <- 1022/2b80 PCI: 00:05.1 cmd <- 143 PCI: 00:05.2 subsystem <- 1022/2b80 PCI: 00:05.2 cmd <- 143 PCI: 00:06.0 bridge ctrl <- 0a03 PCI: 00:06.0 cmd <- 144 PCI: 00:06.1 subsystem <- 1022/2b80 PCI: 00:06.1 cmd <- 142 PCI: 00:08.0 subsystem <- 1022/2b80 PCI: 00:08.0 cmd <- 143 PCI: 00:0a.0 bridge ctrl <- 0003 PCI: 00:0a.0 cmd <- 140 PCI: 00:0b.0 bridge ctrl <- 0003 PCI: 00:0b.0 cmd <- 140 PCI: 00:0c.0 bridge ctrl <- 0003 PCI: 00:0c.0 cmd <- 140 PCI: 00:0d.0 bridge ctrl <- 0003 PCI: 00:0d.0 cmd <- 140 PCI: 00:0e.0 bridge ctrl <- 0003 PCI: 00:0e.0 cmd <- 140 PCI: 00:0f.0 bridge ctrl <- 000b PCI: 00:0f.0 cmd <- 147 PCI: 07:00.0 cmd <- 143 PCI: 00:18.1 subsystem <- 1022/2b80 PCI: 00:18.1 cmd <- 140 PCI: 00:18.2 subsystem <- 1022/2b80 PCI: 00:18.2 cmd <- 140 PCI: 00:18.3 cmd <- 140 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b Initializing CPU #0 CPU: vendor AMD device 40f33 CPU: family 0f, model 43, stepping 03 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Processor model unknown Setting up local apic... apic_id: 0x00 done. ECC Disabled CPU #0 Initialized Initializing CPU #1 Waiting for 1 CPUS to stop CPU: vendor AMD device 40f33 CPU: family 0f, model 43, stepping 03 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Processor model unknown Setting up local apic... apic_id: 0x01 done. CPU #1 Initialized All AP CPUs stopped PCI: 00:18.0 init PCI: 00:01.0 init set power on after power fail RTC Init RTC: Checksum invalid zeroing cmos Invalid CMOS LB checksum PNP: 002e.1 init PNP: 002e.4 init FAN_CTL: reg = 0x02a9, read value = 0x50 FAN_CTL: reg = 0x02a9, writing value = 0xd7 PNP: 002e.5 init PNP: 002e.6 init PCI: 00:01.1 init PCI: 00:02.1 init PCI: 00:04.0 init IDE0 PCI: 00:05.0 init SATA S SATA P PCI: 00:05.1 init SATA S SATA P PCI: 00:05.2 init SATA S SATA P PCI: 00:06.0 init dev_root mem base = 0x00e0000000 [0x50] <-- 0xe0000000 PCI: 00:06.1 init base = f7140000 codec_mask = 01 codec viddid: 10ec0883 No verb! PCI: 00:08.0 init MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1 PCI: 00:0a.0 init PCI: 00:0b.0 init PCI: 00:0c.0 init PCI: 00:0d.0 init PCI: 00:0e.0 init PCI: 00:0f.0 init PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. PCI: 00:01.2 init PCI: 00:01.3 init PCI: 07:00.0 init rom address for PCI: 07:00.0 = f7000000 copying VGA ROM Image from 0xf7000000 to 0xc0000, 0xda00 bytes entering emulator halt_sys: file /home/selmys/seneca/072/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 Devices initialized Writing IRQ routing tables to 0xf0000...done. Wrote the mp table end at: 00000020 - 00000274 Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0400 to 0x00100000 Wrote linuxbios table at: 00000530 - 00000de8 checksum 4410
Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x3afe0 offset 0xc0 filesize 0x10fc8 (cleaned up) New segment addr 0x100000 size 0x3afe0 offset 0xc0 filesize 0x10fc8 New segment addr 0x13afe0 size 0x48 offset 0x110a0 filesize 0x48 (cleaned up) New segment addr 0x13afe0 size 0x48 offset 0x110a0 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x00000000bff80000 memsz: 0x000000000003afe0 filesz: 0x0000000000010fc8 Clearing Segment: addr: 0x00000000bff90fc8 memsz: 0x000000000002a018 Loading Segment: addr: 0x00000000bffbafe0 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x10c98c FILO version 0.5 (selmys@amdx2) Tue Jul 24 12:05:13 EDT 2007 menu: hde4:/boot/grub/lbmenu.lst hde: LBA48 120GB: WDC WD1200JD-00HBB0 Mounted ext2fs Mounted ext2fs Found Linux version 2.6.22 (root@amdx2) #1 SMP Tue Jul 10 17:07:13 EDT 2007 bzImage. Loading kernel... ok Loading initrd... ok Jumping to entry point... Linux version 2.6.22 (root@amdx2) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Tue Jul 10 17:07:13 EDT 2007 Command line: root=/dev/sda3 ro acpi_use_timer_override console=tty0 console=ttyS0,115200 BIOS-provided physical RAM map: BIOS-e820: 0000000000001000 - 00000000000a0000 (usable) BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) BIOS-e820: 0000000000100000 - 00000000c0000000 (usable) BIOS-e820: 0000000100000000 - 0000000140000000 (usable) end_pfn_map = 1310720 DMI not present or invalid. Scanning NUMA topology in Northbridge 24 No NUMA configuration found Faking a node at 0000000000000000-0000000140000000 Bootmem setup node 0 0000000000000000-0000000140000000 Zone PFN ranges: DMA 1 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1310720 early_node_map[4] active PFN ranges 0: 1 -> 160 0: 192 -> 240 0: 256 -> 786432 0: 1048576 -> 1310720 Intel MultiProcessor Specification v1.4 MPTABLE: OEM ID: GIGABYTE MPTABLE: Product ID: M57SLI MPTABLE: APIC at: 0xFEE00000 Processor #0 (Bootup-CPU) Processor #1 I/O APIC #2 at 0xF7144000. Setting APIC routing to flat Processors: 2 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000c0000 swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 swsusp: Registered nosave memory region: 00000000c0000000 - 0000000100000000 Allocating PCI resources starting at c4000000 (gap: c0000000:40000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 43208 bytes of per cpu data Built 1 zonelists. Total pages: 1029337 Kernel command line: root=/dev/sda3 ro acpi_use_timer_override console=tty0 console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Marking TSC unstable due to TSCs unsynchronized time.c: Detected 3000.016 MHz processor. Console: colour VGA+ 80x25 Checking aperture... CPU 0: aperture @ f0000000 size 64 MB Memory: 4128244k/5242880k available (2318k kernel code, 65864k reserved, 1362k data, 320k init) Calibrating delay using timer specific routine.. 6002.61 BogoMIPS (lpj=3001305) Security Framework v1.0.0 initialized SELinux: Initializing. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20070126 ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126] ACPI: Unable to load the System Description Tables Using local APIC timer interrupts. result 12500074 Detected 12.500 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 5999.19 BogoMIPS (lpj=2999596) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Processor model unknown stepping 03 Brought up 2 CPUs migration_cost=303 NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Probing PCI hardware PCI: Using IRQ router default [10de/0370] at 0000:00:06.0 PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20 PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21 PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:07:00.0[A] -> IRQ 17 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ f0000000 size 65536 KB PCI-DMA: using GART IOMMU. PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0f.0 IO window: 1000-1fff MEM window: f4000000-f70fffff PREFETCH window: e0000000-efffffff NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 524288 (order: 11, 12582912 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 3085k freed audit: initializing netlink socket (disabled) audit(1185311416.972:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 usbcore: registered new interface driver libusual PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input1 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 2 AMD Processor model unknown processors (version 2.00.00) powernow-k8: MP systems not supported by PSB BIOS structure powernow-k8: MP systems not supported by PSB BIOS structure drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Freeing unused kernel memory: 320k freed Write protecting the kernel read-only data: 1048k Red Hat nash version 6.0.9 starting Mounting proc filesystem Mounting sysfs filesystem Creating /dev Creating initial device nodes Setting up hotplug. Creating block device nodes. LoUSB Universal Host Controller Interface driver v3.0 ading uhci-hcd.ko module Loadinohci_hcd 0000:00:02.0: OHCI Host Controller g ohci-hcd.ko moohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 dule ohci_hcd 0000:00:02.0: irq 22, io mem 0xf7145000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected Loading ehci-hcdehci_hcd 0000:00:02.1: EHCI Host Controller .ko module ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:02.1: debug port 1 ehci_hcd 0000:00:02.1: irq 23, io mem 0xf714a000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected Loading mbcache.ko module Loading jbd.ko module Loading ext3.ko module Loading scsi_mod.ko module SCSI subsystem initialized Loading sd_mod.ko module Loading libata.ko module Loading sata_nv.ko module scsi0 : sata_nv scsi1 : sata_nv ata1: SATA max UDMA/133 cmd 0x0000000000013000 ctl 0x0000000000013072 bmdma 0x0000000000012cd0 irq 20 ata2: SATA max UDMA/133 cmd 0x0000000000013010 ctl 0x0000000000013082 bmdma 0x0000000000012cd8 irq 20 usb 1-9: new low speed USB device using ohci_hcd and address 2 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: Host Protected Area detected: current size: 234439535 sectors native size: 234441648 sectors ata1.00: ATA-6: WDC WD1200JD-00HBB0, 08.02D08, max UDMA/133 ata1.00: 234439535 sectors, multi 0: LBA48 ata1.00: Host Protected Area detected: current size: 234439535 sectors native size: 234441648 sectors ata1.00: configured for UDMA/133 usb 1-9: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /class/input/input2 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-9 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: Host Protected Area detected: current size: 625140335 sectors native size: 625142448 sectors ata2.00: ATA-7: ST3320620SV, 3.ACG, max UDMA/133 ata2.00: 625140335 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: Host Protected Area detected: current size: 625140335 sectors native size: 625142448 sectors ata2.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD1200JD-00H 08.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 234439535 512-byte hardware sectors (120033 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 234439535 512-byte hardware sectors (120033 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3320620SV 3.AC PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 625140335 512-byte hardware sectors (320072 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 625140335 512-byte hardware sectors (320072 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 1:0:0:0: [sdb] Attached SCSI disk scsi2 : sata_nv scsi3 : sata_nv ata3: SATA max UDMA/133 cmd 0x0000000000013020 ctl 0x0000000000013092 bmdma 0x0000000000012ce0 irq 23 ata4: SATA max UDMA/133 cmd 0x0000000000013030 ctl 0x00000000000130a2 bmdma 0x0000000000012ce8 irq 23 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi4 : sata_nv scsi5 : sata_nv ata5: SATA max UDMA/133 cmd 0x0000000000013040 ctl 0x00000000000130b2 bmdma 0x0000000000012cf0 irq 21 ata6: SATA max UDMA/133 cmd 0x0000000000013050 ctl 0x00000000000130c2 bmdma 0x0000000000012cf8 irq 21 ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) Waiting for driver initialization. Loading ata_generic.ko module Loading pata_amdscsi6 : pata_amd .ko module scsi7 : pata_amd ata7: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x0000000000012cc0 irq 14 ata8: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x0000000000012cc8 irq 15 ata7.00: ATAPI: HL-DT-STDVD-RAM GSA-H54N, 1.00, max UDMA/66 ata7.00: limited to UDMA/33 due to 40-wire cable ata7.00: configured for UDMA/33 scsi 6:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H54N 1.00 PQ: 0 ANSI: 5 Waiting for driver initialization. Trying to resume from LABEL=SWAP-sda2 No suspend signature on swap, not resuming. Creating root device. Mounting root filesystem. kjournald starting. Commit interval 5 seconds Setting up otherEXT3-fs: mounted filesystem with ordered data mode. filesystems. Setting up new root fs no fstab.sys, mounting internal defaults Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys SELinux: Disabled at runtime. audit(1185311426.887:2): selinux=0 auid=4294967295 INIT: version 2.86 booting Welcome to Fedora Press 'I' to enter interactive startup. Setting clock (localtime): Tue Jul 24 21:10:30 EDT 2007 [ OK ] Starting udev: [ OK ] Loading default keymap (us): [ OK ] Setting hostname amdx2: [ OK ] No devices found Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda3 /1: clean, 333611/12210528 files, 3520645/12209400 blocks [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a /dev/sdb1 /home: clean, 399442/39075840 files, 27757182/78142160 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 5 Entering non-interactive startup Starting background readahead (early, fast mode): [ OK ] Checking for hardware changes [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... done. [ OK ] Starting auditd: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting irqbalance: [ OK ] Starting rpcbind: [ OK ] Starting NFS statd: [ OK ] Starting RPC idmapd: [ OK ] Starting system message bus: [ OK ] [ OK ] Bluetooth services:[ OK ] Mounting other filesystems: [ OK ] Starting PC/SC smart card daemon (pcscd): [ OK ] Starting hidd: [ OK ] Starting autofs: Loading autofs4: [ OK ] Starting automount: [ OK ] [ OK ] Starting hpiod: [ OK ] Starting hpssd: [ OK ] Starting cups: [ OK ] Starting sshd: [ OK ] Starting xinetd: [ OK ] Starting ntpd: [ OK ] Starting sendmail: [ OK ] Starting sm-client: [ OK ] Network Audio System Release 1.9 [ OK ] Starting ConsoleKit: [ OK ] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] Starting background readahead (later, fast mode): [ OK ] Starting dhcdbd:[ OK ] Starting libvirtd daemon: [ OK ] Starting yum-updatesd: Bridge firewalling registered [ OK ] Starting Avahi daemon... ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (8192 buckets, 65536 max) [ OK ] Starting HAL daemon: [ OK ] Starting smartd: [ OK ] �������������������������������������������������������������