So, here now the booting with standard filo (just the delay(1) patched) which works fine and the completely patched filo (same Config). Unfortunately the initrd is not found in the later case :(
Thanks,
Andi
standard filo: ============================= LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:38:44 CEST 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107121207110202 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 ht reset -
LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:38:44 CEST 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107120707110210 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 Ram1.00 Ram2.00 Unbuffered 333Mhz Interleaved RAM: 0x00400000 KB Ram3 dimm_mask = 00000033 x4_mask = 00000000 x16_mask = 00000000 single_rank_mask = 00000000 ODC = 00111322 Addr Timing= 002b2220 Initializing memory: done RAM: 0x00500000 KB Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB Setting variable MTRR 3, base: 2048MB, range: 1024MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=13 done set DQS timing:DQSPos: 00 done set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=34 done Total DQS Training : tsc [00]=00000000459aab84 Total DQS Training : tsc [01]=000000004753ffde Total DQS Training : tsc [02]=000000009cc8465f Total DQS Training : tsc [03]=000000009f127ae6 Ram4 v_esp=000cee78 testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying LinuxBIOS to RAM. src=fffdf000 dst=00100000 linxbios_ram.nrv2b length = 0000d634 linxbios_ram.bin length = 00022510 Jumping to LinuxBIOS. LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:38:44 CEST 2007 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled PCI: 00:18.3 siblings=1 CPU: APIC: 00 enabled CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 00 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:00.0 [10de/0369] enabled PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010 PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [10de/0369] enabled PCI: 00:01.0 [10de/0360] enabled PCI: 00:01.1 [10de/0368] enabled PCI: 00:01.2 [10de/036a] enabled PCI: 00:01.3 [10de/036b] enabled PCI: 00:02.0 [10de/036c] enabled PCI: 00:02.1 [10de/036d] enabled PCI: 00:04.0 [10de/036e] enabled PCI: 00:05.0 [10de/037f] enabled PCI: 00:05.1 [10de/037f] enabled PCI: 00:05.2 [10de/037f] enabled PCI: 00:06.0 [10de/0370] enabled PCI: 00:06.1 [10de/0371] enabled PCI: 00:08.0 [10de/0373] enabled PCI: 00:0a.0 [10de/0376] enabled PCI: 00:0b.0 [10de/0374] enabled PCI: 00:0c.0 [10de/0374] enabled PCI: 00:0d.0 [10de/0378] enabled PCI: 00:0e.0 [10de/0375] enabled PCI: 00:0f.0 [10de/0377] enabled PNP: 002e.0 disabled PNP: 002e.1 enabled PNP: 002e.2 disabled PNP: 002e.3 disabled PNP: 002e.4 enabled PNP: 002e.5 enabled PNP: 002e.6 enabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled PCI: pci_scan_bus for bus 01 PCI: pci_scan_bus returning with max=001 PCI: pci_scan_bus for bus 02 PCI: pci_scan_bus returning with max=002 PCI: pci_scan_bus for bus 03 PCI: pci_scan_bus returning with max=003 PCI: pci_scan_bus for bus 04 PCI: pci_scan_bus returning with max=004 PCI: pci_scan_bus for bus 05 PCI: pci_scan_bus returning with max=005 PCI: pci_scan_bus for bus 06 PCI: pci_scan_bus returning with max=006 PCI: pci_scan_bus for bus 07 PCI: 07:00.0 [10de/0392] enabled PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 done Allocating resources... Reading resources... PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 02 io PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 02 mem PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem Done reading resources. Allocating VGA resource PCI: 07:00.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0f.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] io <node 0 link 0> PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] prefmem <node 0 link 0> PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f61fffff] mem <node 0 link 0> PCI: 00:01.0 14 <- [0x00f6144000 - 0x00f6144fff] mem PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] io PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] io PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] irq PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq PCI: 00:01.1 10 <- [0x0000002c00 - 0x0000002c3f] io PCI: 00:01.1 20 <- [0x0000002c40 - 0x0000002c7f] io PCI: 00:01.1 24 <- [0x0000002c80 - 0x0000002cbf] io PCI: 00:01.1 60 <- [0x0000002000 - 0x00000020ff] io PCI: 00:01.1 64 <- [0x0000002400 - 0x00000024ff] io PCI: 00:01.1 68 <- [0x0000002800 - 0x00000028ff] io PCI: 00:01.3 10 <- [0x00f6100000 - 0x00f613ffff] mem PCI: 00:02.0 10 <- [0x00f6145000 - 0x00f6145fff] mem PCI: 00:02.1 10 <- [0x00f614a000 - 0x00f614a0ff] mem PCI: 00:04.0 20 <- [0x0000002cc0 - 0x0000002ccf] io PCI: 00:05.0 10 <- [0x0000003000 - 0x0000003007] io PCI: 00:05.0 14 <- [0x0000003070 - 0x0000003073] io PCI: 00:05.0 18 <- [0x0000003010 - 0x0000003017] io PCI: 00:05.0 1c <- [0x0000003080 - 0x0000003083] io PCI: 00:05.0 20 <- [0x0000002cd0 - 0x0000002cdf] io PCI: 00:05.0 24 <- [0x00f6146000 - 0x00f6146fff] mem PCI: 00:05.1 10 <- [0x0000003020 - 0x0000003027] io PCI: 00:05.1 14 <- [0x0000003090 - 0x0000003093] io PCI: 00:05.1 18 <- [0x0000003030 - 0x0000003037] io PCI: 00:05.1 1c <- [0x00000030a0 - 0x00000030a3] io PCI: 00:05.1 20 <- [0x0000002ce0 - 0x0000002cef] io PCI: 00:05.1 24 <- [0x00f6147000 - 0x00f6147fff] mem PCI: 00:05.2 10 <- [0x0000003040 - 0x0000003047] io PCI: 00:05.2 14 <- [0x00000030b0 - 0x00000030b3] io PCI: 00:05.2 18 <- [0x0000003050 - 0x0000003057] io PCI: 00:05.2 1c <- [0x00000030c0 - 0x00000030c3] io PCI: 00:05.2 20 <- [0x0000002cf0 - 0x0000002cff] io PCI: 00:05.2 24 <- [0x00f6148000 - 0x00f6148fff] mem PCI: 00:06.1 10 <- [0x00f6140000 - 0x00f6143fff] mem PCI: 00:08.0 10 <- [0x00f6149000 - 0x00f6149fff] mem PCI: 00:08.0 14 <- [0x0000003060 - 0x0000003067] io PCI: 00:08.0 18 <- [0x00f614b000 - 0x00f614b0ff] mem PCI: 00:08.0 1c <- [0x00f614c000 - 0x00f614c00f] mem PCI: 00:0f.0 1c <- [0x0000001000 - 0x0000001fff] bus 07 io PCI: 00:0f.0 24 <- [0x00e0000000 - 0x00efffffff] bus 07 prefmem PCI: 00:0f.0 20 <- [0x00f4000000 - 0x00f60fffff] bus 07 mem PCI: 07:00.0 10 <- [0x00f4000000 - 0x00f4ffffff] mem PCI: 07:00.0 14 <- [0x00e0000000 - 0x00efffffff] prefmem64 PCI: 07:00.0 1c <- [0x00f5000000 - 0x00f5ffffff] mem64 PCI: 07:00.0 24 <- [0x0000001000 - 0x000000107f] io PCI: 07:00.0 30 <- [0x00f6000000 - 0x00f601ffff] romem PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 140 PCI: 00:00.0 subsystem <- 1022/2b80 PCI: 00:00.0 cmd <- 146 PCI: 00:01.0 subsystem <- 1022/2b80 PCI: 00:01.0 cmd <- 14f mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297 mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237 mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060 mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064 PCI: 00:01.1 subsystem <- 1022/2b80 PCI: 00:01.1 cmd <- 141 PCI: 00:01.2 cmd <- 540 PCI: 00:01.3 cmd <- 142 PCI: 00:02.0 subsystem <- 1022/2b80 PCI: 00:02.0 cmd <- 142 PCI: 00:02.1 subsystem <- 1022/2b80 PCI: 00:02.1 cmd <- 142 PCI: 00:04.0 subsystem <- 1022/2b80 PCI: 00:04.0 cmd <- 141 PCI: 00:05.0 subsystem <- 1022/2b80 PCI: 00:05.0 cmd <- 143 PCI: 00:05.1 subsystem <- 1022/2b80 PCI: 00:05.1 cmd <- 143 PCI: 00:05.2 subsystem <- 1022/2b80 PCI: 00:05.2 cmd <- 143 PCI: 00:06.0 bridge ctrl <- 0a03 PCI: 00:06.0 cmd <- 144 PCI: 00:06.1 subsystem <- 1022/2b80 PCI: 00:06.1 cmd <- 142 PCI: 00:08.0 subsystem <- 1022/2b80 PCI: 00:08.0 cmd <- 143 PCI: 00:0a.0 bridge ctrl <- 0003 PCI: 00:0a.0 cmd <- 140 PCI: 00:0b.0 bridge ctrl <- 0003 PCI: 00:0b.0 cmd <- 140 PCI: 00:0c.0 bridge ctrl <- 0003 PCI: 00:0c.0 cmd <- 140 PCI: 00:0d.0 bridge ctrl <- 0003 PCI: 00:0d.0 cmd <- 140 PCI: 00:0e.0 bridge ctrl <- 0003 PCI: 00:0e.0 cmd <- 140 PCI: 00:0f.0 bridge ctrl <- 000b PCI: 00:0f.0 cmd <- 147 PCI: 07:00.0 cmd <- 143 PCI: 00:18.1 subsystem <- 1022/2b80 PCI: 00:18.1 cmd <- 140 PCI: 00:18.2 subsystem <- 1022/2b80 PCI: 00:18.2 cmd <- 140 PCI: 00:18.3 cmd <- 140 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b Initializing CPU #0 CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x00 done. ECC Disabled CPU #0 Initialized Initializing CPU #1 Waiting for 1 CPUS to stop CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x01 done. CPU #1 Initialized All AP CPUs stopped PCI: 00:18.0 init PCI: 00:01.0 init set power on after power fail RTC Init RTC: Checksum invalid zeroing cmos Invalid CMOS LB checksum PNP: 002e.1 init PNP: 002e.4 init FAN_CTL: reg = 0x02a9, read value = 0x50 FAN_CTL: reg = 0x02a9, writing value = 0xd7 PNP: 002e.5 init PNP: 002e.6 init PCI: 00:01.1 init PCI: 00:02.1 init PCI: 00:04.0 init IDE0 PCI: 00:05.0 init SATA S SATA P PCI: 00:05.1 init SATA S SATA P PCI: 00:05.2 init SATA S SATA P PCI: 00:06.0 init dev_root mem base = 0x00e0000000 [0x50] <-- 0xe0000000 PCI: 00:06.1 init base = f6140000 codec_mask = 01 codec viddid: 10ec0883 No verb! PCI: 00:08.0 init MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1 PCI: 00:0a.0 init PCI: 00:0b.0 init PCI: 00:0c.0 init PCI: 00:0d.0 init PCI: 00:0e.0 init PCI: 00:0f.0 init PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. PCI: 00:01.2 init PCI: 00:01.3 init PCI: 07:00.0 init rom address for PCI: 07:00.0 = f6000000 copying VGA ROM Image from 0xf6000000 to 0xc0000, 0xf600 bytes entering emulator halt_sys: file /home/andi/freeBIOS/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 Devices initialized Writing IRQ routing tables to 0xf0000...done. Wrote the mp table end at: 00000020 - 00000274 Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0400 to 0x00100000 Wrote linuxbios table at: 00000530 - 00000dd4 checksum 5c17
Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x30700 offset 0xc0 filesize 0xb268 (cleaned up) New segment addr 0x100000 size 0x30700 offset 0xc0 filesize 0xb268 New segment addr 0x130700 size 0x48 offset 0xb340 filesize 0x48 (cleaned up) New segment addr 0x130700 size 0x48 offset 0xb340 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x00000000bff80000 memsz: 0x0000000000030700 filesz: 0x000000000000b268 Clearing Segment: addr: 0x00000000bff8b268 memsz: 0x0000000000025498 Loading Segment: addr: 0x00000000bffb0700 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x108e64 FILO version 0.5 (andi@flashgordon) Tue Jun 5 19:36:25 CEST 2007 setup_timers: CPU 2400 MHz Press <Enter> for default boot, or <Esc> for boot prompt... 5 4 3 2 1 timed out boot: hde5:/vmlinuz initrd=hde5:/boot/initrd.img-2.6.21-1-amd64 root=/dev/sda2 ro console=ttyS0,115200 find_ide_controller: found PCI IDE controller 10de:037f prog_if=0x85 find_ide_controller: primary channel: native PCI mode find_ide_controller: cmd_base=0x3000 ctrl_base=0x3070 ide_software_reset: Waiting for ide2 to become ready for reset... ok init_drive: Testing for hde init_drive: Probing for hde init_drive: LBA mode, sectors=268435455 init_drive: LBA48 mode, sectors=488395055 init_drive: Init device params... ok hde: LBA48 250GB: SAMSUNG SP2504C init_drive: Testing for hdf init_drive: Probing for hdf print_status: IDE: status=0x0, err=0x0 init_drive: Testing for hdf init_drive: Probing for hdf print_status: IDE: status=0x0, err=0x0 Mounted ext2fs Found Linux version 2.6.21-1-amd64 (unknown@Debian) #1 SMP Fri May 18 23:28:21 CEST 2007 bzImage. Loading kernel... ok Loading initrd... ok Jumping to entry point... Linux version 2.6.21-1-amd64 (Debian 2.6.21-2) (waldi@debian.org) (gcc version 4.1.3 20070514 (prerelease) (Debian 4.1.2-7)) #1 SMP Fri May 18 23:28:21 CEST 2007 Command line: root=/dev/sda2 ro console=ttyS0,115200 BIOS-provided physical RAM map: BIOS-e820: 0000000000001000 - 00000000000a0000 (usable) BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) BIOS-e820: 0000000000100000 - 00000000c0000000 (usable) BIOS-e820: 0000000100000000 - 0000000140000000 (usable) end_pfn_map = 1310720 DMI not present or invalid. Scanning NUMA topology in Northbridge 24 Number of nodes 1 Node 0 MemBase 0000000000000000 Limit 0000000140000000 Using node hash shift of 63 Bootmem setup node 0 0000000000000000-0000000140000000 Zone PFN ranges: DMA 1 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1310720 early_node_map[4] active PFN ranges 0: 1 -> 160 0: 192 -> 240 0: 256 -> 786432 0: 1048576 -> 1310720 Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override Intel MultiProcessor Specification v1.4 MPTABLE: OEM ID: GIGABYTE MPTABLE: Product ID: M57SLI MPTABLE: APIC at: 0xFEE00000 Processor #0 (Bootup-CPU) Processor #1 I/O APIC #2 at 0xF6144000. Setting APIC routing to physical flat Processors: 2 Nosave address range: 00000000000a0000 - 00000000000c0000 Nosave address range: 00000000000f0000 - 0000000000100000 Nosave address range: 00000000c0000000 - 0000000100000000 Allocating PCI resources starting at c4000000 (gap: c0000000:40000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 37504 bytes of per cpu data Built 1 zonelists. Total pages: 1029631 Kernel command line: root=/dev/sda2 ro console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Detected 2400.010 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... CPU 0: aperture @ f0000000 size 64 MB Memory: 4106608k/5242880k available (1975k kernel code, 87500k reserved, 931k data, 296k init) Calibrating delay using timer specific routine.. 4803.89 BogoMIPS (lpj=9607797) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20070126 ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126] ACPI: Unable to load the System Description Tables Using local APIC timer interrupts. result 12500064 Detected 12.500 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4800.35 BogoMIPS (lpj=9600704) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 01 Brought up 2 CPUs migration_cost=203 NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Probing PCI hardware PCI: Using IRQ router default [10de/0370] at 0000:00:06.0 PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10 PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20 PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21 PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23 PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22 PCI->APIC IRQ transform: 0000:07:00.0[A] -> IRQ 17 NET: Registered protocol family 8 NET: Registered protocol family 20 PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ f0000000 size 65536 KB PCI-DMA: using GART IOMMU. PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0f.0 IO window: 1000-1fff MEM window: f4000000-f60fffff PREFETCH window: e0000000-efffffff NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 5507k freed audit: initializing netlink socket (disabled) audit(1181065315.696:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 296k freed Loading, please wait... input: AT Translated Set 2 keyboard as /class/input/input0 Begin: Loading essential drivers... ... Done. Begin: Running /scripts/init-premount ... FATAL: Error inserting fan (/lib/modules/2.6.21-1-amd64/kernel/drivers/acpi/fan.ko): No such device WARNING: Error ithermal: Unknown symbol acpi_processor_set_thermal_limit nserting processor (/lib/modules/2.6.21-1-amd64/kernel/drivers/acpi/processor.ko): No such device FATAL: Error inserting thermal (/lib/modules/2.6.21-1-amd64/kernel/drivers/acpi/thermal.ko): Unknown symbol in module, or unknown parameter (see dmesg) ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 22, io mem 0xf6145000 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:02.1: debug port 1 ehci_hcd 0000:00:02.1: irq 23, io mem 0xf614a000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0 NFORCE-MCP55: chipset revision 161 NFORCE-MCP55: not 100% native mode: will probe irqs later NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller ide0: BM-DMA at 0x2cc0-0x2cc7, BIOS settings: hda:pio, hdb:pio hda: Optiarc DVD RW AD-7173A, ATAPI CD/DVD-ROM drive usb 1-2: new low speed USB device using ohci_hcd and address 2 usb 1-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev input: HID 1241:1166 as /class/input/input1 input: USB HID v1.00 Mouse [HID 1241:1166] on usb-0000:00:02.0-2 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 SCSI subsystem initialized forcedeth: using HIGHDMA eth0: forcedeth.c: subsystem: 01022:2b80 bound to 0000:00:08.0 ata1: SATA max UDMA/133 cmd 0x0000000000013000 ctl 0x0000000000013072 bmdma 0x0000000000012cd0 irq 20 ata2: SATA max UDMA/133 cmd 0x0000000000013010 ctl 0x0000000000013082 bmdma 0x0000000000012cd8 irq 20 scsi0 : sata_nv ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: SAMSUNG SP2504C, VT100-50, max UDMA7 ata1.00: 488395055 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0000000000013017 scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5 ata3: SATA max UDMA/133 cmd 0x0000000000013020 ctl 0x0000000000013092 bmdma 0x0000000000012ce0 irq 23 ata4: SATA max UDMA/133 cmd 0x0000000000013030 ctl 0x00000000000130a2 bmdma 0x0000000000012ce8 irq 23 scsi2 : sata_nv ata3: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0000000000013027 scsi3 : sata_nv ata4: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0000000000013037 ata5: SATA max UDMA/133 cmd 0x0000000000013040 ctl 0x00000000000130b2 bmdma 0x0000000000012cf0 irq 21 ata6: SATA max UDMA/133 cmd 0x0000000000013050 ctl 0x00000000000130c2 bmdma 0x0000000000012cf8 irq 21 scsi4 : sata_nv ata5: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0000000000013047 scsi5 : sata_nv ata6: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0000000000013057 SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 <<6>hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 sda5 > sd 0:0:0:0: Attached scsi disk sda Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. Begin: Running /scripts/local-premount ... kinit: name_to_dAttempting manual resume ev_t(/dev/sda1) = sda1(8,1) kinit: trying to resume from /dev/sda1 kinit: No resume image, doing normal boot... Done. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...i2c_adapter i2c-0: nForce2 SMBus adapter at 0x2c40 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2c80 input: PC Speaker as /class/input/input2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... done. GActivating swap...Adding 7815580k swap on /dev/sda1. Priority:-1 extents:1 across:7815580k done. Checking root file system...fsck 1.40-WIP (14-Nov-2006) /dev/sda2: clean, 170121/2443200 files, 1253024/EXT3 FS on sda2, 4883760 blocks internal journal done. Setting the system clock.. Cleaning up ifupdown.... Loading kernel modules...loop: loaded (max 8 devices) powernow_k8: Unknown symbol acpi_processor_notify_smm powernow_k8: Unknown symbol acpi_processor_unregister_performance powernow_k8: Unknown symbol acpi_processor_register_performance it87: Found IT8716F chip at 0x290, revision 0 it87: in3 is VCC (+5V) it87: in7 is VCCH (+5V Stand-By) done. Loading device-mapper supportdevice-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com . Checking file systems...fsck 1.40-WIP (14-Nov-2006) /dev/sda3: clean, 14349/4889248 files, 238250/9765511 blocks /dev/sda5: clean, 28584/1281696 files, 207922/2560351 blocks (check after next mount) done. Setting kernel variables...done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. done. Activating swapfile swap...done. Detecting hardware...Setting up networking.... Configuring network interfaces...done. Starting portmap daemon.... Setting sensors limits: done. Setting console screen modes and fonts. RSetting console screen modes and fonts. Setting up ALSA...done. INIT: Entering runlevel: 2 Starting system log daemon.... Starting kernel log daemon.... Starting virtual private network daemon:. Starting portmap daemon...Already running.. Starting HP Linux Printing and Imaging System: hpiod hpssd. Starting BitTorrent tracker: disabled in /etc/default/bittorrent. Starting console-log:Couldnt get a file descriptor referring to the console E: openvt failed. headless system?...failed. Starting Common Unix Printing System: cupsdlp: driver loaded but no devices found ppdev: user-space parallel port driver . Starting system message bus: dbus. Starting network connection manager: NetworkManager. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting network events dispatcher: NetworkManagerDispatcher. Starting DirMngr: dirmngr. Starting MTA: exim4. Starting LAN Information Server: lisa. Starting internet superserver: inetd. Starting powernowd: required sysfs objects not found! Read /usr/share/doc/powernowd/README.Debian for more information. Starting OpenBSD Secure Shell server: sshdNET: Registered protocol family 10 lo: Disabled Privacy Extensions . Starting file alteration monitor: FAM. Starting GNOME Display Manager: gdm. Starting NFS common utilities: statd. Starting NTP server: ntpd. Starting DHCP D-Bus daemon: dhcdbdmtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining . Starting Hardware abstraction layer: hald. Starting anac(h)ronistic cron: anacron. Starting deferred execution scheduler: atd. Starting periodic command scheduler: crond. Not starting K Display Manager (kdm); it is not the default display manager. mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining ============================== ==============================
fast filo:
============================== LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:47:22 CEST 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107121207110202 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 ht reset -
LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:47:22 CEST 2007 starting... *sysinfo range: [000cf000,000cf730) bsp_apicid=00 core0 started: started ap apicid: 01 SBLink=00 NC node|link=00 begin msr fid, vid 3107120707110210 set fid failed for apicid =00 end msr fid, vid 3107120707110210 mcp55_num:01 Ram1.00 Ram2.00 Unbuffered 333Mhz Interleaved RAM: 0x00400000 KB Ram3 dimm_mask = 00000033 x4_mask = 00000000 x16_mask = 00000000 single_rank_mask = 00000000 ODC = 00111322 Addr Timing= 002b2220 Initializing memory: done RAM: 0x00500000 KB Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB Setting variable MTRR 3, base: 2048MB, range: 1024MB, type WB set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=14 done set DQS timing:DQSPos: 00 done set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=34 done Total DQS Training : tsc [00]=00000000459a078a Total DQS Training : tsc [01]=000000004754aa55 Total DQS Training : tsc [02]=0000000094ce9001 Total DQS Training : tsc [03]=00000000971778f5 Ram4 v_esp=000cee78 testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying LinuxBIOS to RAM. src=fffdf000 dst=00100000 linxbios_ram.nrv2b length = 0000d634 linxbios_ram.bin length = 00022510 Jumping to LinuxBIOS. LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun 5 19:47:22 CEST 2007 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled PCI: 00:18.3 siblings=1 CPU: APIC: 00 enabled CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 00 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:00.0 [10de/0369] enabled PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010 PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [10de/0369] enabled PCI: 00:01.0 [10de/0360] enabled PCI: 00:01.1 [10de/0368] enabled PCI: 00:01.2 [10de/036a] enabled PCI: 00:01.3 [10de/036b] enabled PCI: 00:02.0 [10de/036c] enabled PCI: 00:02.1 [10de/036d] enabled PCI: 00:04.0 [10de/036e] enabled PCI: 00:05.0 [10de/037f] enabled PCI: 00:05.1 [10de/037f] enabled PCI: 00:05.2 [10de/037f] enabled PCI: 00:06.0 [10de/0370] enabled PCI: 00:06.1 [10de/0371] enabled PCI: 00:08.0 [10de/0373] enabled PCI: 00:0a.0 [10de/0376] enabled PCI: 00:0b.0 [10de/0374] enabled PCI: 00:0c.0 [10de/0374] enabled PCI: 00:0d.0 [10de/0378] enabled PCI: 00:0e.0 [10de/0375] enabled PCI: 00:0f.0 [10de/0377] enabled PNP: 002e.0 disabled PNP: 002e.1 enabled PNP: 002e.2 disabled PNP: 002e.3 disabled PNP: 002e.4 enabled PNP: 002e.5 enabled PNP: 002e.6 enabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled PCI: pci_scan_bus for bus 01 PCI: pci_scan_bus returning with max=001 PCI: pci_scan_bus for bus 02 PCI: pci_scan_bus returning with max=002 PCI: pci_scan_bus for bus 03 PCI: pci_scan_bus returning with max=003 PCI: pci_scan_bus for bus 04 PCI: pci_scan_bus returning with max=004 PCI: pci_scan_bus for bus 05 PCI: pci_scan_bus returning with max=005 PCI: pci_scan_bus for bus 06 PCI: pci_scan_bus returning with max=006 PCI: pci_scan_bus for bus 07 PCI: 07:00.0 [10de/0392] enabled PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 PCI: pci_scan_bus returning with max=007 done Allocating resources... Reading resources... PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 02 io PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 02 mem PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem Done reading resources. Allocating VGA resource PCI: 07:00.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0f.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] io <node 0 link 0> PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] prefmem <node 0 link 0> PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f61fffff] mem <node 0 link 0> PCI: 00:01.0 14 <- [0x00f6144000 - 0x00f6144fff] mem PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] io PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] io PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] irq PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq PCI: 00:01.1 10 <- [0x0000002c00 - 0x0000002c3f] io PCI: 00:01.1 20 <- [0x0000002c40 - 0x0000002c7f] io PCI: 00:01.1 24 <- [0x0000002c80 - 0x0000002cbf] io PCI: 00:01.1 60 <- [0x0000002000 - 0x00000020ff] io PCI: 00:01.1 64 <- [0x0000002400 - 0x00000024ff] io PCI: 00:01.1 68 <- [0x0000002800 - 0x00000028ff] io PCI: 00:01.3 10 <- [0x00f6100000 - 0x00f613ffff] mem PCI: 00:02.0 10 <- [0x00f6145000 - 0x00f6145fff] mem PCI: 00:02.1 10 <- [0x00f614a000 - 0x00f614a0ff] mem PCI: 00:04.0 20 <- [0x0000002cc0 - 0x0000002ccf] io PCI: 00:05.0 10 <- [0x0000003000 - 0x0000003007] io PCI: 00:05.0 14 <- [0x0000003070 - 0x0000003073] io PCI: 00:05.0 18 <- [0x0000003010 - 0x0000003017] io PCI: 00:05.0 1c <- [0x0000003080 - 0x0000003083] io PCI: 00:05.0 20 <- [0x0000002cd0 - 0x0000002cdf] io PCI: 00:05.0 24 <- [0x00f6146000 - 0x00f6146fff] mem PCI: 00:05.1 10 <- [0x0000003020 - 0x0000003027] io PCI: 00:05.1 14 <- [0x0000003090 - 0x0000003093] io PCI: 00:05.1 18 <- [0x0000003030 - 0x0000003037] io PCI: 00:05.1 1c <- [0x00000030a0 - 0x00000030a3] io PCI: 00:05.1 20 <- [0x0000002ce0 - 0x0000002cef] io PCI: 00:05.1 24 <- [0x00f6147000 - 0x00f6147fff] mem PCI: 00:05.2 10 <- [0x0000003040 - 0x0000003047] io PCI: 00:05.2 14 <- [0x00000030b0 - 0x00000030b3] io PCI: 00:05.2 18 <- [0x0000003050 - 0x0000003057] io PCI: 00:05.2 1c <- [0x00000030c0 - 0x00000030c3] io PCI: 00:05.2 20 <- [0x0000002cf0 - 0x0000002cff] io PCI: 00:05.2 24 <- [0x00f6148000 - 0x00f6148fff] mem PCI: 00:06.1 10 <- [0x00f6140000 - 0x00f6143fff] mem PCI: 00:08.0 10 <- [0x00f6149000 - 0x00f6149fff] mem PCI: 00:08.0 14 <- [0x0000003060 - 0x0000003067] io PCI: 00:08.0 18 <- [0x00f614b000 - 0x00f614b0ff] mem PCI: 00:08.0 1c <- [0x00f614c000 - 0x00f614c00f] mem PCI: 00:0f.0 1c <- [0x0000001000 - 0x0000001fff] bus 07 io PCI: 00:0f.0 24 <- [0x00e0000000 - 0x00efffffff] bus 07 prefmem PCI: 00:0f.0 20 <- [0x00f4000000 - 0x00f60fffff] bus 07 mem PCI: 07:00.0 10 <- [0x00f4000000 - 0x00f4ffffff] mem PCI: 07:00.0 14 <- [0x00e0000000 - 0x00efffffff] prefmem64 PCI: 07:00.0 1c <- [0x00f5000000 - 0x00f5ffffff] mem64 PCI: 07:00.0 24 <- [0x0000001000 - 0x000000107f] io PCI: 07:00.0 30 <- [0x00f6000000 - 0x00f601ffff] romem PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 140 PCI: 00:00.0 subsystem <- 1022/2b80 PCI: 00:00.0 cmd <- 146 PCI: 00:01.0 subsystem <- 1022/2b80 PCI: 00:01.0 cmd <- 14f mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297 mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237 mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060 mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064 PCI: 00:01.1 subsystem <- 1022/2b80 PCI: 00:01.1 cmd <- 141 PCI: 00:01.2 cmd <- 540 PCI: 00:01.3 cmd <- 142 PCI: 00:02.0 subsystem <- 1022/2b80 PCI: 00:02.0 cmd <- 142 PCI: 00:02.1 subsystem <- 1022/2b80 PCI: 00:02.1 cmd <- 142 PCI: 00:04.0 subsystem <- 1022/2b80 PCI: 00:04.0 cmd <- 141 PCI: 00:05.0 subsystem <- 1022/2b80 PCI: 00:05.0 cmd <- 143 PCI: 00:05.1 subsystem <- 1022/2b80 PCI: 00:05.1 cmd <- 143 PCI: 00:05.2 subsystem <- 1022/2b80 PCI: 00:05.2 cmd <- 143 PCI: 00:06.0 bridge ctrl <- 0a03 PCI: 00:06.0 cmd <- 144 PCI: 00:06.1 subsystem <- 1022/2b80 PCI: 00:06.1 cmd <- 142 PCI: 00:08.0 subsystem <- 1022/2b80 PCI: 00:08.0 cmd <- 143 PCI: 00:0a.0 bridge ctrl <- 0003 PCI: 00:0a.0 cmd <- 140 PCI: 00:0b.0 bridge ctrl <- 0003 PCI: 00:0b.0 cmd <- 140 PCI: 00:0c.0 bridge ctrl <- 0003 PCI: 00:0c.0 cmd <- 140 PCI: 00:0d.0 bridge ctrl <- 0003 PCI: 00:0d.0 cmd <- 140 PCI: 00:0e.0 bridge ctrl <- 0003 PCI: 00:0e.0 cmd <- 140 PCI: 00:0f.0 bridge ctrl <- 000b PCI: 00:0f.0 cmd <- 147 PCI: 07:00.0 cmd <- 143 PCI: 00:18.1 subsystem <- 1022/2b80 PCI: 00:18.1 cmd <- 140 PCI: 00:18.2 subsystem <- 1022/2b80 PCI: 00:18.2 cmd <- 140 PCI: 00:18.3 cmd <- 140 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b Initializing CPU #0 CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x00 done. ECC Disabled CPU #0 Initialized Initializing CPU #1 Waiting for 1 CPUS to stop CPU: vendor AMD device 60fb1 CPU: family 0f, model 6b, stepping 01 Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ Setting up local apic... apic_id: 0x01 done. CPU #1 Initialized All AP CPUs stopped PCI: 00:18.0 init PCI: 00:01.0 init set power on after power fail RTC Init RTC: Checksum invalid zeroing cmos Invalid CMOS LB checksum PNP: 002e.1 init PNP: 002e.4 init FAN_CTL: reg = 0x02a9, read value = 0x50 FAN_CTL: reg = 0x02a9, writing value = 0xd7 PNP: 002e.5 init PNP: 002e.6 init PCI: 00:01.1 init PCI: 00:02.1 init PCI: 00:04.0 init IDE0 PCI: 00:05.0 init SATA S SATA P PCI: 00:05.1 init SATA S SATA P PCI: 00:05.2 init SATA S SATA P PCI: 00:06.0 init dev_root mem base = 0x00e0000000 [0x50] <-- 0xe0000000 PCI: 00:06.1 init base = f6140000 codec_mask = 01 codec viddid: 10ec0883 No verb! PCI: 00:08.0 init MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1 PCI: 00:0a.0 init PCI: 00:0b.0 init PCI: 00:0c.0 init PCI: 00:0d.0 init PCI: 00:0e.0 init PCI: 00:0f.0 init PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. PCI: 00:01.2 init PCI: 00:01.3 init PCI: 07:00.0 init rom address for PCI: 07:00.0 = f6000000 copying VGA ROM Image from 0xf6000000 to 0xc0000, 0xf600 bytes entering emulator halt_sys: file /home/andi/freeBIOS/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387 Devices initialized Writing IRQ routing tables to 0xf0000...done. Wrote the mp table end at: 00000020 - 00000274 Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0400 to 0x00100000 Wrote linuxbios table at: 00000530 - 00000dd4 checksum 601b
Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x31240 offset 0xc0 filesize 0xbda8 (cleaned up) New segment addr 0x100000 size 0x31240 offset 0xc0 filesize 0xbda8 New segment addr 0x131240 size 0x48 offset 0xbe80 filesize 0x48 (cleaned up) New segment addr 0x131240 size 0x48 offset 0xbe80 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x00000000bff80000 memsz: 0x0000000000031240 filesz: 0x000000000000bda8 Clearing Segment: addr: 0x00000000bff8bda8 memsz: 0x0000000000025498 Loading Segment: addr: 0x00000000bffb1240 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x109618 FILO version 0.5 (andi@flashgordon) Tue Jun 5 19:45:50 CEST 2007 setup_timers: CPU 2400 MHz Press <Enter> for default boot, or <Esc> for boot prompt... 5 4 3 2 1 timed out boot: hde5:/vmlinuz initrd=hde5:/boot/initrd.img-2.6.21-1-amd64 root=/dev/sda2 ro console=ttyS0,115200 find_ide_controller: found PCI IDE controller 10de:037f prog_if=0x85 find_ide_controller: primary channel: native PCI mode find_ide_controller: cmd_base=0x3000 ctrl_base=0x3070 ide_software_reset: Waiting for ide2 to become ready for reset... ok init_drive: Testing for hde init_drive: Probing for hde init_drive: LBA mode, sectors=268435455 init_drive: LBA48 mode, sectors=488395055 init_drive: Init device params... ok hde: LBA48 250GB: SAMSUNG SP2504C init_drive: Testing for hdf init_drive: Probing for hdf IDE timeout after 50 ms while waiting for drq() pio_data_in: No DRQ from device after read command print_status: IDE: status=0x0, err=0x0 init_drive: Testing for hdf init_drive: Probing for hdf IDE timeout after 50 ms while waiting for drq() pio_data_in: No DRQ from device after read command print_status: IDE: status=0x0, err=0x0 ide_readmany: sector 0 to 0x0010c040 ide_readmany: sector 132825420 to 0x0010d840 ide_readmany: sector 132825485 to 0x0010da40 ide_readmany: sector 132825486 to 0x0010dc40 Mounted ext2fs ide_readmany: sector 132825491 to 0x0010e640 ide_readmany: sector 132825492 to 0x0010e840 ide_readmany: sector 132825493 to 0x0010ea40 ide_readmany: sector 132825494 to 0x0010ec40 ide_readmany: sector 132825495 to 0x0010ee40 ide_readmany: sector 132825496 to 0x0010f040 ide_readmany: sector 132825497 to 0x0010f240 ide_readmany: sector 132825498 to 0x0010f440 ide_readmany: sector 132825515 to 0x00111640 ide_readmany: sector 132825516 to 0x00111840 ide_readmany: sector 132825517 to 0x00111a40 ide_readmany: sector 132825518 to 0x00111c40 ide_readmany: sector 132825519 to 0x00111e40 ide_readmany: sector 132825520 to 0x00112040 ide_readmany: sector 132825521 to 0x00112240 ide_readmany: sector 132825522 to 0x00112440 ide_readmany: sector 132829571 to 0x0010c640 ide_readmany: sector 132829572 to 0x0010c840 ide_readmany: sector 132829573 to 0x0010ca40 ide_readmany: sector 132829574 to 0x0010cc40 ide_readmany: sector 132829575 to 0x0010ce40 ide_readmany: sector 132829576 to 0x0010d040 ide_readmany: sector 132829577 to 0x0010d240 ide_readmany: sector 132829578 to 0x0010d440 ide_readmany: sector 136233387 to 0x00111640 ide_readmany: sector 136233388 to 0x00111840 ide_readmany: sector 136233389 to 0x00111a40 ide_readmany: sector 136233390 to 0x00111c40 ide_readmany: sector 136233391 to 0x00111e40 ide_readmany: sector 136233392 to 0x00112040 ide_readmany: sector 136233393 to 0x00112240 ide_readmany: sector 136233394 to 0x00112440 ide_readmany: sector 136298891 to 0x0010d640 ide_readmany: sector 136298892 to 0x0010d840 ide_readmany: sector 136298893 to 0x0010da40 ide_readmany: sector 136298894 to 0x0010dc40 ide_readmany: sector 136298895 to 0x0010de40 ide_readmany: sector 136298896 to 0x0010e040 ide_readmany: sector 136298897 to 0x0010e240 ide_readmany: sector 136298898 to 0x0010e440 ext2fs_read_one: block 452608 offset=0 len=52 ret=0 ide_readmany: sector 136446347 to 0x0010d640 ide_readmany: sector 132825515 to 0x00111640 ide_readmany: sector 132825516 to 0x00111840 ide_readmany: sector 132825517 to 0x00111a40 ide_readmany: sector 132825518 to 0x00111c40 ide_readmany: sector 132825519 to 0x00111e40 ide_readmany: sector 132825520 to 0x00112040 ide_readmany: sector 132825521 to 0x00112240 ide_readmany: sector 132825522 to 0x00112440 ide_readmany: sector 136233387 to 0x00111640 ide_readmany: sector 136233388 to 0x00111840 ide_readmany: sector 136233389 to 0x00111a40 ide_readmany: sector 136233390 to 0x00111c40 ide_readmany: sector 136233391 to 0x00111e40 ide_readmany: sector 136233392 to 0x00112040 ide_readmany: sector 136233393 to 0x00112240 ide_readmany: sector 136233394 to 0x00112440 ide_readmany: sector 136298891 to 0x0010d640 ext2fs_read_one: block 452608 offset=0 len=560 ret=0 ide_readmany: sector 136446347 to 0x0010d640 ide_readmany: sector 136446348 to 0x0010d840 Found Linuxblock 452609 offset=1099 len=256 ret=0 ide_readmany: sector 136446357 to 0x0010ea40 version 2.6.21-1-amd64 (unknown@Debian) #1 SMP Fri May 18 23:28:21 CEST 2007 bzImage. Loading kernel... sector 136446443 to 0x00111640 ide_readmany: sector 136446444 to 0x00111840 ide_readmany: sector 136446445 to 0x00111a40 ide_readmany: sector 136446446 to 0x00111c40 ide_readmany: sector 136446447 to 0x00111e40 ide_readmany: sector 136446448 to 0x00112040 ide_readmany: sector 136446449 to 0x00112240 ide_readmany: sector 136446450 to 0x00112440 ext2fs_read_many: 10 blocks 452610 - 452619 len=1561450 ret=0 ide_readmany: sectors 136446363 - 136446442 ( 80) to 0x40231290 ext2fs_read_many: 372 blocks 452621 - 452992 len=1520490 ret=40960 ide_readmany: sectors 136446451 - 136446706 (256) to 0x4023b290 ide_readmany: sectors 136446707 - 136446962 (256) to 0x4025b290 ide_readmany: sectors 136446963 - 136447218 (256) to 0x4027b290 ide_readmany: sectors 136447219 - 136447474 (256) to 0x4029b290 ide_readmany: sectors 136447475 - 136447730 (256) to 0x402bb290 ide_readmany: sectors 136447731 - 136447986 (256) to 0x402db290 ide_readmany: sectors 136447987 - 136448242 (256) to 0x402fb290 ide_readmany: sectors 136448243 - 136448498 (256) to 0x4031b290 ide_readmany: sectors 136448499 - 136448754 (256) to 0x4033b290 ide_readmany: sectors 136448755 - 136449010 (256) to 0x4035b290 ide_readmany: sectors 136449011 - 136449266 (256) to 0x4037b290 ide_readmany: sectors 136449267 - 136449426 (160) to 0x4039b290 ext2fs_read: discarding 3222 surplus bytes ext2fs_read: done reading many len=0 ret=1561450 ok ide_readmany: sector 132825493 to 0x0010ea40 ide_readmany: sector 132825515 to 0x00111640 ide_readmany: sector 132825516 to 0x00111840 ide_readmany: sector 132825517 to 0x00111a40 ide_readmany: sector 132825518 to 0x00111c40 ide_readmany: sector 132825519 to 0x00111e40 ide_readmany: sector 132825520 to 0x00112040 ide_readmany: sector 132825521 to 0x00112240 ide_readmany: sector 132825522 to 0x00112440 File not found Can't open initrd: hde5:/boot/initrd.img-2.6.21-1-amd64