Hi, My mainboard is GX1+5530A+97317. After boot from linuxbios+linux-2.4.20, eth0 and USB work fine but keyboard not work and linux seems can't receive data from serial port(I can see output from SERIAL_CONSOLE). Please help me.
Thanks! /////////////////////////////////////////////// LinuxBIOS-1.0.0 Fri May 30 17:07:05 CST 2003 starting...
Setting up default parameters for memory
Sizing memory
Probing for DIMM0
Found DIMM0
Page Size: 00001000
Component Banks: 4
Module Banks: 1
DIMM size: 04000000
Probing for DIMM1
Memory sizing done, MC_BANK_CFG = 0x00701420
Copying LinuxBIOS to ram.
Jumping to LinuxBIOS.
LinuxBIOS-1.0.0 Fri May 30 17:07:05 CST 2003 booting...
Finding PCI configuration type.
PCI: Using configuration type 1
Scanning PCI bus...PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1078/0001]
PCI: 00:0f.0 [10ec/8139]
PCI: 00:12.0 [1078/0100]
PCI: 00:12.1 [1078/0101]
PCI: 00:12.2 [1078/0102]
PCI: 00:12.3 [1078/0103]
PCI: 00:12.4 [1078/0104]
PCI: 00:13.0 [0e11/a0f8]
PCI: pci_scan_bus returning with max=00
done
Allocating PCI resources...
ASSIGN RESOURCES, bus 0
PCI: 00:0f.0 10 <- [0x00001000 - 0x000010ff] io
PCI: 00:0f.0 14 <- [0xfebfd000 - 0xfebfd0ff] mem
PCI: 00:12.1 10 <- [0xfebfe000 - 0xfebfe0ff] mem
PCI: 00:12.2 20 <- [0x00001400 - 0x0000147f] io
PCI: 00:12.3 10 <- [0xfebff000 - 0xfebff07f] mem
PCI: 00:12.4 10 <- [0xfebfb000 - 0xfebfbfff] mem
PCI: 00:13.0 10 <- [0xfebfc000 - 0xfebfcfff] mem
ASSIGNED RESOURCES, bus 0
Allocating VGA resource
done.
Enabling PCI resourcess...PCI: 00:00.0 cmd <- 07
PCI: 00:0f.0 cmd <- 03
PCI: 00:12.0 cmd <- 0f
PCI: 00:12.1 cmd <- 02
PCI: 00:12.2 cmd <- 01
PCI: 00:12.3 cmd <- 02
PCI: 00:12.4 cmd <- 03
PCI: 00:13.0 cmd <- 02
done.
Initializing PCI devices...
PCI devices initialized
DIMM0: 64MB (4kB page size, 4 component banks, 1 module banks)
DIMM1: empty
Reserving 4096kB for video memory
BC_DRAM_TOP = 0x03bfffff
MC_GBASE_ADD = 0x00000078
totalram: 60M
Initializing CPU #0
Enabling cache...done.
Max cpuid index : 2
Vendor ID : Geode by NSC
Processor Type : 0x00
Processor Family : 0x05
Processor Model : 0x04
Processor Mask : 0x00
Processor Stepping : 0x00
Feature flags : 0x00808131
Cache/TLB descriptor values: 1 reads required
Desc 0x70 : UNKNOWN
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
Desc 0x80 : UNKNOWN
Desc 0x00 : null
Desc 0x00 : null
Desc 0x00 : null
done.
CPU #0 Initialized
Enable FLASH
Set F0/0x52 to 0xee
cs5530: Enabling Primary IDE Controller
cs5530: Enabling Secondary IDE Controller
Set F0/0x5b to |= 1 << 5(0x38)
Final southbridge fixup
F0/5c: 0x0000
cs5530: PCI INTA=15, INTB=9, INTC=9, INTD=9
F0/5c: 0x999f
4d0: 0x00
4d1: 0x00
4d0: 0x00
4d1: 0x82
F0/5b = 0x38
cs5530: Enabling Primary IDE Controller
F0/5b = 0x38
cs5530: USB is on INTA, IRQ 15
Final mainboard fixup
nano: Setting eth0 IRQ to 9
Wrote linuxbios table at: 00000500 - 00000698 checksum 8bc9
Jumping to linuxbiosmain()...
Welcome to start32, the open sourced starter.
This space will eventually hold more diagnostic information.
January 2000, James Hendricks, Dale Webster, and Ron Minnich.
Version 0.1
Trying polled ide
Waiting for ide disks to spin up
This is a hard coded delay and longer than necessary.
.clocks_per_usec: 264
.
offset=00000200
I am now initializing the ide system
UQNAUT MIFERABLLcl1t 050
init_drive: sectors_per_track=[63], num_heads=[15], num_cylinders=[10585]
IDE0 15/10585/63 cap: 0f00
init_drive: sectors_per_track=[0], num_heads=[0], num_cylinders=[0]
Controller 1: detect FAILED (1)
Gunzip setup
gunzip_setup
output data is 0x00100000
Gunzipping boot code
................ <1023>
command line - [vga=785 root=/dev/hda2 console=tty0 console=ttyS0,9600n8]
Jumping to boot code
Linux version 2.4.20 () (gcc version 2.96 20000731 (Linux-Mandrake 8.0 2.96-0.48mdk)) #6 Tue May 27 18:14:43 CST 2003
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000003b00000 (usable)
59MB LOWMEM available.
On node 0 totalpages: 15104
zone(0): 4096 pages.
zone(1): 11008 pages.
zone(2): 0 pages.
Kernel command line: vga=785 root=/dev/hda2 console=tty0 console=ttyS0,9600n8
Initializing CPU#0
Working around Cyrix MediaGX virtual DMA bugs.
Detected 200.455 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 399.76 BogoMIPS
Memory: 57172k/60416k available (1323k kernel code, 2856k reserved, 333k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Working around Cyrix MediaGX virtual DMA bugs.
CPU: NSC Geode(TM) Integrated Processor by National Semi stepping 02
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x10)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CS5530: IDE controller on PCI bus 00 dev 92
CS5530: detected chipset, but driver not compiled in!
CS5530: chipset revision 0
CS5530: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:pio, hdd:pio
hda: C/H/S=0/0/0 from BIOS ignored
hda: QUANTUM FIREBALLlct10 05, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
blk: queue c0308544, I/O limit 4095Mb (mask 0xffffffff)
hda: 10002825 sectors (5121 MB) w/418KiB Cache, CHS=10585/15/63, (U)DMA
Partition check:
hda: [PTBL] [622/255/63] hda1 hda2 hda3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 49152K size 1024 blocksize
loop: loaded (max 8 devices)
8139cp: 10/100 PCI Ethernet driver v0.3.0 (Sep 29, 2002)
8139cp: pci dev 00:0f.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xc4800000, 00:e0:4c:26:c6:fa, IRQ 9
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 10:12:59 May 15 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-ohci.c: USB OHCI at membase 0xc4802000, IRQ 15
usb-ohci.c: usb-00:13.0, Compaq Computer Corporation ZFMicro Chipset USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 256k freed
INIT: version 2.78 booting
kernel loading successed.
Checking flash file system...
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Flash file system OK!
INIT: Entering runlevel: 2
Loading network interface...eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
eth0: Too much work at interrupt, IntrStatus=0x0001.
V1.0.1 command line interface version 1.0.127
login: ______________________________________
===================================================================