coreboot

coreboot@coreboot.org

10 participants
39711 discussions

答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

If I changed config.lb PCI 1:0.2 on --> PCI 1:0.2 off The PCI 1:0.0 and PCI 1:0.1 will be disabled together. According to AMD 8111 data sheet, LPC 0x48, only can be disabled the device in second bus by device num, and the three USB share one device number. So I guess the code about 0x47 must be there. YH -----邮件原件----- 发件人: ron minnich [mailto:rminnich@lanl.gov] 发送时间: 2004年5月5日 9:28 收件人: YhLu 抄送: Stefan Reinauer; linuxbios(a)clustermatic.org 主题: Re: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 5 May 2004, YhLu wrote: > I change my mind, disable that in Config.lb is better and less code. good! ron

4 5

答复: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

According to AMD, USB 2 in amd8111 will never work. YH -----邮件原件----- 发件人: ron minnich [mailto:rminnich@lanl.gov] 发送时间: 2004年5月5日 7:07 收件人: YhLu 抄送: Stefan Reinauer; linuxbios(a)clustermatic.org 主题: Re: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 5 May 2004, ron minnich wrote: > On Tue, 4 May 2004, YhLu wrote: > > > I'm going to add several lines in amd8111_enable of amd8111.c to disable > > USB2 in amd8111. > > > > /* disable usb2 in amd 8111 because it does not work awlays*/ > > byte = pci_read_config8(lpc_dev, 0x47); > > byte |= (1<<7); > > pci_write_config8(lpc_dev, 0x47, byte); > > this is the wrong way to do this, please don't do it just yet. ok, the other two changes look fine. This disabling is fine if the kernel can later re-enable, but I doubt the kernel will do that. We need a way to make this usb enable/disable visible at configuration time, so people can turn on/off as needed, unless usb2.0 on the 8111 NEVER work. I am willing to guess it will work someday, and this built-in disable will come back to bite us. ron

3 2

Re: Which kernel for framebuffering?
by YhLu 05 May '04

05 May '04

David, Please refer to the patch for 2.4.22 and 2.6.5, or you can put that in CVS ... Also please refer to the matix to see which kernel you want to use. Please make sure enable ati xl framebuffer only in kernel config. ( don't enable noinit) Regards YH -----邮件原件----- 发件人: Hendricks David W. [mailto:dwh@lanl.gov] 发送时间: 2004年5月4日 13:31 收件人: YhLu 抄送: linuxbios(a)clustermatic.org 主题: Which kernel for framebuffering? We were able to build and boot LinuxBIOS with VGA support for an HDAMA. FILO came up on screen and the keyboard worked, but we've been unable to get Linux framebuffering to work using a 64-bit kernel. We were wondering if there's anything special you had to do to make it work, or any special kernel version or patches we need to use.

2 1

Re: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

Committed. Disable AMD8111 USB2 and remove hard code addr in amd8111 IDE CVS: ---------------------------------------------------------------------- CVS: Enter Log. Lines beginning with `CVS:' are removed automatically CVS: CVS: Committing in . CVS: CVS: Modified Files: CVS: src/mainboard/tyan/s2850/Config.lb CVS: src/mainboard/tyan/s2875/Config.lb CVS: src/mainboard/tyan/s2880/Config.lb CVS: src/mainboard/tyan/s2881/Config.lb CVS: src/mainboard/tyan/s2882/Config.lb CVS: src/mainboard/tyan/s2885/Config.lb CVS: src/mainboard/tyan/s4880/Config.lb CVS: src/mainboard/tyan/s4882/Config.lb CVS: src/southbridge/amd/amd8111/amd8111.c CVS: src/southbridge/amd/amd8111/amd8111_ide.c CVS: ---------------------------------------------------------------------- -----邮件原件----- 发件人: ron minnich [mailto:rminnich@lanl.gov] 发送时间: 2004年5月5日 10:23 收件人: YhLu 抄送: Stefan Reinauer; linuxbios(a)clustermatic.org 主题: Re: 答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 5 May 2004, YhLu wrote: > If I changed config.lb > PCI 1:0.2 on --> PCI 1:0.2 off > The PCI 1:0.0 and PCI 1:0.1 will be disabled together. > > According to AMD 8111 data sheet, LPC 0x48, only can be disabled the device > in second bus by device num, and the three USB share one device number. > > So I guess the code about 0x47 must be there. sounds ok. ron

1 0

答复: 答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

So everyone need to find lpc_dev at first??? YH -----邮件原件----- 发件人: Li-Ta Lo [mailto:ollie@lanl.gov] 发送时间: 2004年5月5日 10:28 收件人: YhLu 抄送: ron minnich; Stefan Reinauer; LinuxBIOS 主题: Re: 答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 2004-05-05 at 10:51, YhLu wrote: > If I changed config.lb > PCI 1:0.2 on --> PCI 1:0.2 off > The PCI 1:0.0 and PCI 1:0.1 will be disabled together. > > According to AMD 8111 data sheet, LPC 0x48, only can be disabled the device > in second bus by device num, and the three USB share one device number. > > So I guess the code about 0x47 must be there. > Ron and I just dicurssed about the enable/disable mechanism for amd8111. We are going to implement a slightly better one soon. Actually, the enable/disable for devices in amd8111 is multiplexed in amd8111_enable and the device_operation::enable() is directed to amd8111_enable. We are going to demultiplex this and each devices has its own "real" enable method. Ollie

2 1

答复: 答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

I add some lines in amd8111, if USB2 is disabled, it will don't touch 0x48, only touch 0x47. if ((dev->vendor == PCI_VENDOR_ID_AMD) && (dev->device == PCI_DEVICE_ID_AMD_8111_USB2)) { if(!dev->enabled) { byte = pci_read_config8(lpc_dev, 0x47); byte |= (1<<7); pci_write_config8(lpc_dev, 0x47, byte); return; } } reg = reg_old = pci_read_config16(lpc_dev, 0x48); reg &= ~(1 << index); if (dev->enabled) { reg |= (1 << index); } if (reg != reg_old) { pci_write_config16(lpc_dev, 0x48, reg); } -----邮件原件----- 发件人: Li-Ta Lo [mailto:ollie@lanl.gov] 发送时间: 2004年5月5日 10:28 收件人: YhLu 抄送: ron minnich; Stefan Reinauer; LinuxBIOS 主题: Re: 答复: 答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 2004-05-05 at 10:51, YhLu wrote: > If I changed config.lb > PCI 1:0.2 on --> PCI 1:0.2 off > The PCI 1:0.0 and PCI 1:0.1 will be disabled together. > > According to AMD 8111 data sheet, LPC 0x48, only can be disabled the device > in second bus by device num, and the three USB share one device number. > > So I guess the code about 0x47 must be there. > Ron and I just dicurssed about the enable/disable mechanism for amd8111. We are going to implement a slightly better one soon. Actually, the enable/disable for devices in amd8111 is multiplexed in amd8111_enable and the device_operation::enable() is directed to amd8111_enable. We are going to demultiplex this and each devices has its own "real" enable method. Ollie

1 0

答复: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

I change my mind, disable that in Config.lb is better and less code. YH -----邮件原件----- 发件人: ron minnich [mailto:rminnich@lanl.gov] 发送时间: 2004年5月5日 9:25 收件人: YhLu 抄送: Stefan Reinauer; linuxbios(a)clustermatic.org 主题: Re: 答复: Disable USB2 in AMD8111 and remove ide hardcode io addr On Wed, 5 May 2004, YhLu wrote: > According to AMD, USB 2 in amd8111 will never work. well, that's certainly interesting. If AMD is certain about that, and no one else objects, I remove any concerns I have about this code. But please put in a more informative comment such as "will never work" thanks ron

2 1

Disable USB2 in AMD8111 and remove ide hardcode io addr
by YhLu 05 May '04

05 May '04

Ron, I'm going to add several lines in amd8111_enable of amd8111.c to disable USB2 in amd8111. /* disable usb2 in amd 8111 because it does not work awlays*/ byte = pci_read_config8(lpc_dev, 0x47); byte |= (1<<7); pci_write_config8(lpc_dev, 0x47, byte); Also will remove several lines in amd8111_ide.c /* The AMD768 has a bug where the BM DMA address must be * 256 byte aligned while it is only 16 bytes long. * Hard code this to a valid address below 0x1000 * where automatic port address assignment starts. * FIXME: I assume the 8111 does the same thing. We should * clarify. stepan(a)suse.de */ pci_write_config32(dev, 0x20, 0xf01); pci_write_config32(dev, 0x48, 0x205e5e5e); word = 0x06a; pci_write_config16(dev, 0x4c, word); and add byte = 0x20 ; // Latency: 64-->32 pci_write_config8(dev, 0xd, byte); regards YH

5 6

Which kernel for framebuffering?
by Hendricks David W. 04 May '04

04 May '04

We were able to build and boot LinuxBIOS with VGA support for an HDAMA. FILO came up on screen and the keyboard worked, but we've been unable to get Linux framebuffering to work using a 64-bit kernel. We were wondering if there's anything special you had to do to make it work, or any special kernel version or patches we need to use.

1 0

Enable v.s. Enabled
by Li-Ta Lo 30 Apr '04

30 Apr '04

Hi, I changed the device:enable and chip_device_path::enable to device:enabled and chip_device_path::enabled because they are acutally verbs describe the status of the devices. I also change all the affected code I can find, there should be no problems except you have to re-run the config tool. Ollie

2 2

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot