coreboot

coreboot@coreboot.org

12 participants
39779 discussions

Etherboot version
by Ignacio Verona 14 May '04

14 May '04

Hi! I've been trying to load linuxbios into my Epia MII but first of all, I've a problem with etherboot version. It seems that the latest stable release is 5.0.11 but I can't get it to compile correctly because in src/Config I can't find the line CFLAGS32 += -DPCIBIOS, but the line -DPCBIOS. If if comment out this line, etherboot will not compile. What is wrong? Should I use other version of etherboot? If so, where can I find older releases? Thanks!

1 0

答复: EPIA V2 : BTEXT config problems
by YhLu 14 May '04

14 May '04

If you want to use BTEXT config, you need to make sure the VGA driver has enable the frame buffer and call btext_setup.... Regards YH -----邮件原件----- 发件人: Mathieu Deschamps [mailto:mdeschamps@mangrove-systems.com] 发送时间: 2004年5月14日 7:03 收件人: Linuxbios(a)clustermatic.org 主题: EPIA V2 : BTEXT config problems I am trying first to get btext config to display something on my screen but i does nothing. I have no payload, no videoBIOS ROM, and no activate VGABIOS. I have this output (truncat. ) my CyberBlade i3 chipset is in 01:00.0 108 Disabling cache$ 109 Clearing mtrr$ 110 Setting XIP$ 111 Enabled the cache$ 112 Copying LinuxBIOS to ram.$ 113 Jumping to LinuxBIOS.$ 114 POST: 0x39$ 115 LinuxBIOS-1.1.6.0Fallback Fri May 14 15:25:51 CEST 2004 booting...$ 116 POST: 0x40$ 117 Finding PCI configuration type.$ 118 PCI: Using configuration type 1$ 119 POST: 0x5f$ 120 Enumerating static devices...$ 121 Enumerating: VIA vt8601 Northbridge$ 122 Enumerating: VIA vt8231$ 123 Enumerating buses...$ 124 PCI: pci_scan_bus for bus 0$ 125 POST: 0x24$ 126 PCI: 00:00.0 [1106/0601] enabled$ 127 PCI: 00:01.0 [1106/8601] enabled$ 128 PCI: 00:11.0 [1106/8231] enabled$ 129 PCI: 00:11.1 [1106/0571] enabled$ 130 PCI: 00:11.2 [1106/3038] enablhi,ed$ 131 PCI: 00:11.3 [1106/3038] enabled$ 132 PCI: 00:11.4 [1106/8235] enabled$ 133 PCI: 00:11.5 [1106/3058] enabled$ 134 PCI: 00:11.6 [1106/3068] enabled$ 135 PCI: 00:12.0 [1106/3065] enabled$ 136 POST: 0x25$ 137 PCI: pci_scan_bus for bus 1$ 138 POST: 0x24$ 139 PCI: 01:00.0 [1023/8500] enabled$ 140 POST: 0x25$ 141 PCI: pci_scan_bus returning with max=01$ 142 POST: 0x55$ 143 PCI: pci_scan_bus returning with max=01$ 144 POST: 0x55$ 145 done$ 146 POST: 0x66$ 147 Allocating resources...$ 148 Allocating VGA resource$ 149 ASSIGN RESOURCES, bus 0$ 150 PCI: 00:00.0 10 <- [0xe0000000 - 0xefffffff] prefmem$ 151 PCI: 00:01.0 1c <- [0x00001000 - 0x00000fff] bus 1 io$ 152 PCI: 00:01.0 24 <- [0xf1100000 - 0xf10fffff] bus 1 prefmem$ 153 PCI: 00:01.0 20 <- [0xf0000000 - 0xf10fffff] bus 1 mem$ 154 ASSIGN RESOURCES, bus 1$ 155 PCI: 01:00.0 10 <- [0xf0000000 - 0xf07fffff] mem$ 156 PCI: 01:00.0 14 <- [0xf1000000 - 0xf101ffff] mem$ 157 PCI: 01:00.0 18 <- [0xf0800000 - 0xf0ffffff] mem$ 158 ASSIGNED RESOURCES, bus 1$ 159 PCI: 00:11.1 20 <- [0x00001c40 - 0x00001c4f] io$ 160 PCI: 00:11.2 20 <- [0x00001c00 - 0x00001c1f] io$ 161 PCI: 00:11.3 20 <- [0x00001c20 - 0x00001c3f] io$ 162 PCI: 00:11.5 10 <- [0x00001000 - 0x000010ff] io$ 163 PCI: 00:11.5 14 <- [0x00001c50 - 0x00001c53] io$ 164 PCI: 00:11.5 18 <- [0x00001c60 - 0x00001c63] io$ 165 PCI: 00:11.6 10 <- [0x00001400 - 0x000014ff] io$ 166 PCI: 00:12.0 10 <- [0x00001800 - 0x000018ff] io$ 167 PCI: 00:12.0 14 <- [0xf1100000 - 0xf11000ff] mem$ 168 ASSIGNED RESOURCES, bus 0$ 169 done.$ 170 POST: 0x88$ 171 Enabling resourcess...$ 172 PCI: 00:00.0 cmd <- 146$ 173 PCI: 00:01.0 bridge ctrl <- 000f$ 174 PCI: 00:01.0 cmd <- 147$ 175 PCI: 01:00.0 cmd <- 147$ 176 PCI: 00:11.0 cmd <- 1c7$ 177 PCI: 00:11.1 cmd <- 147$ 178 PCI: 00:11.2 cmd <- 147$ 179 PCI: 00:11.3 cmd <- 147$ 180 PCI: 00:11.4 cmd <- 140$ 181 PCI: 00:11.5 cmd <- 141$ 182 PCI: 00:11.6 cmd <- 141$ 183 PCI: 00:12.0 cmd <- 147$ 184 done.$ 185 Initializing devices...$ 186 Devices initialized$ 187 POST: 0x89$ 188 vt8231 init$ 189 IDE enable in reg. 50 is 0x7$ 190 set IDE reg. 50 to 0x7$ 191 IRQs in reg. 4c are 0x4$ 192 setting reg. 4c to 0x4$ 193 enables in reg 0x40 0xb$ 194 enables in reg 0x40 read back as 0xb$ 195 enables in reg 0x9 0x8f$ 196 enables in reg 0x9 read back as 0x8f$ 197 command in reg 0x4 0x7$ 198 command in reg 0x4 reads back as 0x7$ 199 Ethernet fixup$ 200 Configuring VIA LAN$ 201 RTC Init$ 202 Invalid CMOS LB checksum$ 203 pci_routing_fixup: dev is 0002e098$ 204 setting southbridge$ 205 Assigning IRQ 11 to 0:11.1$ 206 Readback = 255$ 207 Assigning IRQ 12 to 0:11.2$ 208 Readback = 12$ 209 Assigning IRQ 12 to 0:11.3$ 210 Readback = 12$ 211 Assigning IRQ 10 to 0:11.5$ 212 Readback = 10$ 213 Assigning IRQ 10 to 0:11.6$ 214 Readback = 10$ 215 setting ethernet$ 216 Assigning IRQ 11 to 0:12.0$ 217 Readback = 11$ 218 setting pci slot$ 219 pci_routing_fixup: DONE$ 220 I would set ram size to 0x20000 Kbytes$ 221 mem[0].basek = 00000000 mem[0].sizek = 00020000$ 222 mem[1].basek = 00000000 mem[1].sizek = 00000000$ 223 mem[2].basek = 00000000 mem[2].sizek = 00000000$ 224 mem[3].basek = 00000000 mem[3].sizek = 00000000$ 225 mem[4].basek = 00000000 mem[4].sizek = 00000000$ 226 mem[5].basek = 00000000 mem[5].sizek = 00000000$ 227 mem[6].basek = 00000000 mem[6].sizek = 00000000$ 228 mem[7].basek = 00000000 mem[7].sizek = 00000000$ 229 mem[8].basek = 00000000 mem[8].sizek = 00000000$ 230 mem[9].basek = 00000000 mem[9].sizek = 00000000$ 231 POST: 0x70$ 232 totalram: 128M$ 233 Initializing CPU #0$ 234 POST: 0x60$ 235 Enabling cache...$ 236 Setting fixed MTRRs(0-88) type: UC$ 237 Setting fixed MTRRs(0-88) type: WB$ 238 DONE fixed MTRRs$ 239 Setting variable MTRR 0, base: 0MB, range: 128MB, type WB$ 240 DONE variable MTRRs$ 241 Clear out the extra MTRR's$ 242 call intel_enable_fixed_mtrr()$ 243 call intel_enable_var_mtrr()$ 244 Leave setup_mtrrs$ 245 POST: 0x6a$ 246 done.$ 247 Max cpuid index : 1$ 248 Vendor ID : CentaurHauls$ 249 Processor Type : 0x00$ 250 Processor Family : 0x06$ 251 Processor Model : 0x07$ 252 Processor Mask : 0x00$ 253 Processor Stepping : 0x08$ 254 Feature flags : 0x00803135$ 255 POST: 0x92$ 256 MTRR check$ 257 Fixed MTRRs : Enabled$ 258 Variable MTRRs: Enabled$ 259 POST: 0x93$ 260 Updating microcode$ 261 microcode_info: sig = 0x00000678 pf=0x00000001 rev = 0x0000000al apic...done.$ 262 POSTtirq_routing_table() - irq_rosinuxbios ta 0 00 00 00 00 00 06 11 10 60 $ 263 0x7$ 264 0x60: 00 00 00 00 00 00 02 08 0100 20 00 00 00 $ 265 0x80: 00 00 00 00 0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 $ 266 0xfodev/hda3 console=tty0 $ 267 Welcomeea hard coded delay and longer thaclocks_per_usec: 960$ 268 .$ 269 found PCI IDE controller 1106:0571 prog_if=0x8f$ 270 primary channel: native PCI mode$ 271 Waiting for ide0 to become ready for reset... ok$ 272 Testing for hda$ 273 Probing for hda$ 274 LBA mode, sectors=40021632$ 275 Init device params... ok$ 276 hda: LBA 20GB: Maxtor 32049U3 $ 277 Partition 1 start 63 length 2040192$ 278 Unknown filesystem type$ 279 command terminated by signal 2 real 13.67 user 0.01 sys 0.01 ---------------------------------------------- Comments : This is a BTEXT_CONFIG test no payload, no videoROM, no VGABIOS from a cold boot : no screen "video mode on" (led goes green) from a warn boot : the screen flashes but nothing written (bad init?) Le jeu 13/05/2004 à 17:49, ron minnich a écrit : > On 13 May 2004, Mathieu Deschamps wrote: > > > hum i see ... but didn't we got native LinuxBIOS VGA up on EPIA-M ? > > on V1 not V2. It works fine on V1. But ram detection on V1 is not working. > You only get one size ram. > _______________________________________________ Linuxbios mailing list Linuxbios(a)clustermatic.org http://www.clustermatic.org/mailman/listinfo/linuxbios

1 0

About EPIA-M Frambuffer + VGA on V2 status
by Mathieu Deschamps 14 May '04

14 May '04

Hi, Acutally , I've LinuxBios IDE_BOOT onto hard drive. All this is fascinating. I'am so excited :) Ok , ok i've got a "unknown file system" : i've got ext3 root partition on it, couldn't Linuxbios boot ext3 part just by now ? If true want option should I add ? I've seen this about framebuffer and VGA on epia-M: http://www.clustermatic.org/pipermail/linuxbios/2004-March/006817.html http://www.clustermatic.org/pipermail/linuxbios/2004-April/007494.html humm i'd love to see tux sitting on the corner of my screen... Dmitry or Ron may I ask you if you could send me the HOWTO that you were talking about ? Is it already operationnal ? What type of option does/will it requiere to get set in Config ? I need also these info this because I'am coding a sort linuxbios command center script. It lets user choose between IDE HARD BOOT or CF BOOT or ETHER BOOT and so on, and automatically add options, configure stuffs and lauches makes logs strings, and point errors or dangereous warnings at the user. It also gather video.bios and flashes the whole into a specified target (for now ROM chip). What do you think of this ? Thanks. mathieu

3 5

Re: HDAMA+FILO booting SUSE Linux
by Craig C Forney 14 May '04

14 May '04

I'm still having problems installing a new disk using LinuxBIOS+FILO on an HDAMA board with a Suse AMD64 distribution. Although the "nomce" argument helped quite a bit moving things along, I still can't install a new disk from the Suse 9.0 or 9.1 Pro AMD64 distributions using the serial port only with an Arima HDAMA board with LinuxBIOS and FILO. The only way I've gotten an bootable installation going is to use the Phoenix BIOS to install on a drive, then use the Suse repair function under LinuxBIOS to clean it up and then boot it. I thought the following installation attempts might be interesting to others. Except for the Suse 9.1 Live CD attempts, I was attempting to boot from CD and do a complete install of Suse 9.0 or 9.1 on the hard drive. If there are any obvious errors in my FILO boot arguments, please let me know. Some of these scenarios just might not be reasonable things to do at this point, given the state of the hardware/software components. That info would be appreciated as well. If there is a different AMD64 Linux distribution that someone has had installation success with, that would be nice, as well. The following scenarios were created using the sourceforge snapshot of linuxbios from May 10, 2004, compiled for and run on an Arima HDAMA board with FILO 0.4.1 as the payload with a Maxtor disk drive as /dev/hda and a Hitachi DVD drive as /dev/hdc: 1. Media: Suse 9.0 amd64 distribution DVD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 nmi-watchdog=0 acpi=off nomce ide=nodma apm=off Results: Hangs during YaST after successfully determining the Partitioning installation settings after the "Evaluating package selection ..." message disappears Partitioning * Format Partition /dev/hda2 15.6 MB (for /boot with ext2) * Format Partition /dev/hda4 3.3 GB (for / with reiser) * Format Partition /dev/hda3 501.4 MB (for swap) 2. Media: Suse 9.0 amd64 distribution DVD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 Results: Same as 1. above 3. Media: Suse 9.1 amd64 distribution DVD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 nmi-watchdog=0 acpi=off nomce ide=nodma apm=off Results: Hangs during initial boot of linux after ide1 line as follows: ... Linux agpgart interface v0.100 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD8111: IDE controller at PCI slot 0000:01:04.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0x2430-0x2437, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x2438-0x243f, BIOS settings: hdc:pio, hdd:pio hda: Maxtor 84320D4, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: HITACHI DVD-ROM GD-7500, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 <-- hangs here hda: max request size: 128KiB <-- never gets here hda: 8439184 sectors (4320 MB) w/256KiB Cache, CHS=8930/15/63, UDMA(33) hda: hda1 hda2 hda3 hda4 4. Media: Suse 9.1 LIVE CD Filo boot arguments: hdc:/vmlinuz initrd=hdc:/initrd.gz console=ttyS0,115200n8 Results: Panics kernel as follows: ... mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay ACPI: ACPI tables contain no PCI IRQ routing entries PCI: Invalid ACPI-PCI IRQ routing table PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) ... the first call_usermodehelper: pci_bus CPU 0: Machine Check Exception: 0000000000000004 Bank 4: b200000000070f0f Kernel panic: CPU context corrupt 5. Media: Suse 9.1 LIVE CD Filo boot arguments: hdc:/vmlinuz initrd=hdc:/initrd.gz console=ttyS0,115200n8 nomce Results: Hangs after setting up ethernet: Starting PCMCIA Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: No IRQ known for interrupt pin D of device 0000:04:00.2. Please try using pci=biosirq. drivers/usb/core/hcd-pci.c: Found HC with no IRQ. Check BIOS/PCI 0000:04:00.2 setup! startproc: exit status of parent of /sbin/cardmgr: 1 failed Shutting down network interfaces: eth0 device: Broadcom Corporation NetXtreme BCM5702 Gigabit Edonenet (rev 02) eth1 device: Broadcom Corporation NetXtreme BCM5702 Gigabit Ethernet (rev 02) eth1 configuration: done Shutting down service network . . . . . . . . . . . . . done Hint: you may set mandatory devices in /etc/sysconfig/network/config Setting up network interfaces: lo lo IP address: 127.0.0.1/8 done eth0 device: Broadcom Corporation NetXtreme BCM5702 Gigabit Ethernet (rev 02) SIOCSIFFLAGS: Device or resource busy eth0 (DHCP) . NET: Registered protocol family 17 . . . . no IP address yet... backgrounding. waiting eth1 device: Broadcom Corporation NetXtreme BCM5702 Gigabit Ethernet (rev 02) eth1 No configuration found for eth1 unused Setting up service network . . . . . . . . . . . . . . Done 6. Media: Suse 9.1 LIVE CD Filo boot arguments: hdc:/vmlinuz initrd=hdc:/initrd.gz console=ttyS0,115200n8 nmi-watchdog=0 acpi=off nomce ide=nodma apm=off single Results: Boots into single user mode just fine. 7. Media: Suse 9.1 32-bit distribution DVD or CD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 Results: Kernel panics ... do_initcalls init_elf_binfmt NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay ACPI: ACPI tables contain no PCI IRQ routing entries PCI: Invalid ACPI-PCI IRQ routing table PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) ... the first call_usermodehelper: pci_bus CPU 0: Machine Check Exception: 0000000000000004 Bank 4: b200000000070f0f Kernel panic: CPU context corrupt 8. Media: Suse 9.1 32-bit distribution DVD or CD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 nomce Results: Installs OK 9. Media: Suse 9.1 32-bit distribution DVD or CD (YaST new installation) Filo boot arguments: hdc:/boot/loader/linux initrd=hdc:/boot/loader/initrd console=ttyS0,115200n8 nmi-watchdog=0 acpi=off nomce ide=nodma apm=off Results: Installs OK Whew! Thanks, Craig Forney Opus Innovations LLC

1 0

答复: USB boot
by YhLu 13 May '04

13 May '04

There is partition FAT in the flash disk. Another question. If add code to handle OHCI ED and TD, Can I still use bulk_transfer and control_message? Regards YH -----邮件原件----- 发件人: Steven James [mailto:pyro@linuxlabs.com] 发送时间: 2004年5月13日 19:49 收件人: YhLu 抄送: Linuxbios; Takeshi Sone 主题: Re: USB boot Greetings, I'll see if I can dig up the old debugging captures, I may still have them. The enumeration of the USB bus looks good. The problems seem to start with: 536870913 536870912 byte blocks ll_read_block returns 512 0: boot=00000000, start=00000000 length=00000000 1: boot=00000000, start=00000000 length=00000000 2: boot=00000000, start=00000000 length=00000000 3: boot=00000000, start=00000000 length=00000000 GEt capacity returned a VERY unreasonable result :-) The read of the partition block seems to have actually read the block. Does the drive have a partition table on it? If not, try putting one on it and trying the boot so we can see if it actually read the block correctly or if the data went to the wrong place. G'day, sjames -------------------------steven james, director of research, linux labs ... ........ ..... .... 230 peachtree st nw ste 2701 the original linux labs atlanta.ga.us 30303 -since 1995 http://www.linuxlabs.com office & fax 866.545.6306 ----------------------------------------------------------------------- On Thu, 13 May 2004, YhLu wrote:

1 0

USB boot
by YhLu 13 May '04

13 May '04

Steven, I switch to S4882, because it has via USB chip. And it is UHCI. Also I got some output. It shows Product: USB Flash Drive Serial: 070B01001340CA0 Can you send me some debug output message to let me figure out which is right or not? Regards YH LinuxBIOS-1.1.62.0_Fallback Thu May 13 15:11:33 PDT 2004 starting... LinuxBIOS-1.1.62.0_Fallback Thu May 13 15:47:33 PDT 2004 booting... Finding PCI configuration type. Enumerating static devices... Enumerating buses... done Allocating resources...ERROR: PNP: 002e.b 70 not allocated done. Enabling resourcess... done. Initializing devices... set power on after power fail Devices initialized totalram: 16128M Initializing CPU #0 Enabling cache...done. Setting up local apic...done. CPU #0 Initialized Initializing CPU #1 Enabling cache...done. Initializing CPU #2 Enabling cache...done. Initializing CPU #3 Waiting for 4 CPUS to stop Enabling cache...done. Setting up local apic...done. CPU #1 Initialized Waiting for 3 CPUS to stop Setting up local apic...done. CPU #2 Initialized Waiting for 2 CPUS to stop Setting up local apic...done. CPU #3 Initialized Checking IRQ routing tables... /home/yhlu/xx/xx/freebios2/src/arch/i386/boot/pirq_routing.c: 41:check_pirq_routing_table() - checksum is: 0x9a but should be: 0x5b done. Copying IRQ routing tables to 0xf0000...done. Verifing copy of IRQ routing tables at 0xf0000...done Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 Loading Etherboot version: 5.2.4 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 2285 Mhz Etherboot 5.2.4 (GPL) http://etherboot.org Tagged ELF for [TG3][FILO] Relocating _text from: [0002d2a0,0008e8d0) to [efe9e9d0,eff00000) Probing pci nic... [tg3-5704]Ethernet addr: 00:E0:81:61:8C:27 Tigon3 [partno(BCM95704A6) rev 2003 PHY(5401)] (PCIX:100MHz:64-bit) <abort> Probing pci nic... [tg3-5704]Ethernet addr: 00:E0:81:61:8C:28 Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) <abort> Probing pci nic... Probing pci disk... [FILO]FILO version 0.4.1 (root@tst2723-rh9) Thu May 13 15:47:25 PDT 2004 Press <Enter> for default boot, or <Esc> for boot prompt... timed out boot: uda1:/ram0_2.5_2.6.5_k8.2_mydisk7.elf LinuxLabs USB bootloader raw frame_list is at 00078560 frame_list is at 00078630 frame_list_link: addr: 00077570 frame_list_link: raw addr: efef5f40 frame_list_link: terminate: 00000000 frame_list_link: queue: 00000001 frame_list_link: depth: 00000000 dummy_td = 0006f500 raw frame_list is at 0007a560 frame_list is at 0007a630 frame_list_link: addr: 00077590 frame_list_link: raw addr: efef5f60 frame_list_link: terminate: 00000000 frame_list_link: queue: 00000001 frame_list_link: depth: 00000000 dummy_td = 0006f540 raw frame_list is at 0007c560 frame_list is at 0007c630 frame_list_link: addr: 000775b0 frame_list_link: raw addr: efef5f80 frame_list_link: terminate: 00000000 frame_list_link: queue: 00000001 frame_list_link: depth: 00000000 dummy_td = 0006f580 raw frame_list is at 0007e560 frame_list is at 0007e630 frame_list_link: addr: 000775d0 frame_list_link: raw addr: efef5fa0 frame_list_link: terminate: 00000000 frame_list_link: queue: 00000001 frame_list_link: depth: 00000000 dummy_td = 0006f5c0 Found OHCI at 0d181630 Resetting OHCI USB HC reset_hc usb-0d181630: ctrl = 0x00000600 ;ohc_init setting framelist to: efef7000 Starting OHCI Found OHCI at 0d182630 Resetting OHCI USB HC reset_hc usb-0d182630: ctrl = 0x00000600 ;ohc_init setting framelist to: efef9000 Starting OHCI Found UHCI at 00002400 Resetting UHCI uhc_init setting framelist to: efefb000 Starting UHCI HCI at 00002400 Found UHCI at 00002420 Resetting UHCI uhc_init setting framelist to: efefd000 Starting UHCI HCI at 00002420 poll_usb1 i=0 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100poll_usb1 i=1 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100poll_usb1 i=2 poll_u_root_hub1 v=00000480 poll_u_root_hub1 v=00001493 poll_u_root_hub2 v=00001493poll_u_root_hub21 v=00001493 Connection on port 00002412 New USB device, setting address 00000003 Fetching device descriptor length Fetching device descriptor Fetching config descriptor length Fetching config descriptor device: bLength: 00000012 type: 00000001 bcdVersion: 0000000200000000 Class: 00000000 SubClass: 00000000 protocol: 00000000 max_packet: 00000040 idVendor: 00001005 idProduct: 0000b113 bcdDeviceVersion: 0000000100000000 iManufacturor: 00000000 iProduct: 00000001 iSerial: 00000002 bNumConfig: 00000001 config: bLength: 00000009 type: 00000002 wTotalLength: 00000020 bNumInterfaces: 00000001 bConfigurationValue: 00000001 iConfiguration: 00000000 bmAttributes: 00000080 bMaxPower: 000000fa Interface(00081057): bLength: 00000009 type: 00000004 bInterfaceNumber: 00000000 bAlternateSetting: 00000000 bNumEndpoints: 00000002 bInterfaceClass: 00000008 bInterfaceSubClass: 00000006 bInterfaceProtocol: 00000050 iInterface: 00000000 Endpoint (00081060): bLength: 00000007 type: 00000005 bEndpointAddress: 00000081 bmAttributes: 00000002 wMaxPacketSize: 00000040 bInterval: 00000000 Endpoint (00081067): bLength: 00000007 type: 00000005 bEndpointAddress: 00000002 bmAttributes: 00000002 wMaxPacketSize: 00000040 bInterval: 00000000 Selecting Configuration number 00000001: clear stall on ep=00000081 clear stall on ep=00000002 00000008:00000006:00000050 Manufacturor: unknown Product: USB Flash Drive Serial: 070B01001340CA0 Mass storage, bulk only SCSI transparent Requesting initial sense data sense data :00000000:00000000:00000000:00000000:00000000:00000000:00000000:00000000:000 00000:00000000:00000000:00000000:00000000:00000000:00000000:00000000:0000000 0:00000000:00000000:00000000:00000000:00000000:00000000:00000000:00000000:00 000000:00000000:00000000:00000000:00000000:00000000:00000000 code = 00000000 key = 00000000 Info: 00000000 536870913 536870912 byte blocks ll_read_block returns 512 0: boot=00000000, start=00000000 length=00000000 1: boot=00000000, start=00000000 length=00000000 2: boot=00000000, start=00000000 length=00000000 3: boot=00000000, start=00000000 length=00000000 DEVICE CONFIGURED poll_usb1 i=3 poll_u_root_hub1 v=00000480 poll_u_root_hub1 v=00000480 poll_usb1 i=0 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_usb1 i=1 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_o_root_hub1 v=00000100 poll_usb1 i=2 poll_u_root_hub1 v=00000480 poll_u_root_hub1 v=00000495 poll_usb1 i=3 poll_u_root_hub1 v=00000480 poll_u_root_hub1 v=00000480 Found USB block device 3 bulk_transfer( dev= 00000003, ep = 00000081, len = 0b8a0000, buffer = 000810ac) = 2048:short transaction: short_transaction:TD(0006f600): short_transaction:type: IN short_transaction:retries: 00000000 short_transaction:active: 00000000 short_transaction:device_addr: 00000003 short_transaction:endpoint: 00000001 short_transaction:data_toggle: 00000001 short_transaction:max_transfer: 0000003f short_transaction:actual: 000007ff short_transaction:link: short_transaction:STALL short_transaction:addr: 0006f620 short_transaction: raw addr: efeedff0 short_transaction:terminate: 00000000 short_transaction:queue: 00000000 short_transaction:depth: 00000001

2 1

Develop && WinXP
by backblue 13 May '04

13 May '04

I would like to use linuxbios but it's not able to any of my (about) 15 motherboards i have at home :(((, what does i need to get suport to them, and where did i start reading? :) Does LinuxBios boots windowsXP? Tks

1 0

Re: flash_rom with exclude range
by YhLu 13 May '04

13 May '04

David, Can you check the code? Ollie is on vocation? Regards YH -----邮件原件----- 发件人: YhLu 发送时间: 2004年5月12日 11:46 收件人: Li-Ta Lo; LinuxBIOS 主题: flash_rom with exclude range Ollie, I add exclude range feature to the Pm49FL004, and it should apply to other chip. But can not make getopt work with input parameter. Please check it. I hardcode exclude_start_position to 0x60000, and exclude_end_postion to 0x8000. Regards YH

4 3

答复: Making payloads
by YhLu 13 May '04

13 May '04

Increase HEAP SIZE. YH -----邮件原件----- 发件人: Jay Miller [mailto:jmiller@actuality-systems.com] 发送时间: 2004年5月13日 12:49 收件人: YhLu; linuxbios(a)clustermatic.org 主题: RE: Making payloads I built tg3--filo.zelf with the latest patch from the link in your message. Getting the follow error message when loading: Loading Etherboot version: 5.2.4 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x4aef5 offset 0xb0 filesize 0xa4b7 (cleaned up) New segment addr 0x20000 size 0x4aef5 offset 0xb0 filesize 0xa4b7 Loading Segment: addr: 0x000000001ffadfe8 memsz: 0x000000000001b00c filesz: 0x00 0000000000a4b7 Clearing Segment: addr: 0x000000001ffb849f memsz: 0x0000000000010b55 Loading Segment: addr: 0x000000000003b00c memsz: 0x000000000002fee9 filesz: 0x00 00000000000000 39:stream_skip() - overflowed source buffer ERROR: Skip of 68437 bytes skiped 23193 bytes Cannot Load ELF Image What am I doing wrong? -J -----Original Message----- From: YhLu [mailto:YhLu@tyan.com] Sent: Thursday, May 13, 2004 1:22 PM To: Jay Miller; linuxbios(a)clustermatic.org Subject: 答复: Making payloads http://sourceforge.net/tracker/index.php?func=detail&aid=943300&group_id=423 3&atid=304233 -----邮件原件----- 发件人: YhLu 发送时间: 2004年5月13日 10:05 收件人: Jay Miller; linuxbios(a)clustermatic.org 主题: 答复: Making payloads Jay, I have merged into FILO into Etherboot. You can get that patch from Etherboot group. So you can build tg3--filo.zelf. About the PCI scan in Etherboot has no problem to find IDE other than bus 0. Current it already supports serial IDE and normal IDE. I'm working on add usb boot into FILO in Etherboot. The AMD8111 is using OHCI, and I'm trying to make use steven code for USB boot, but it is only support UHCI. OHCI has hardware support for ED (QH) instead of SW QH. Maybe I need to get UHCI addon card at first. Please let me know if you has problem to get filo patch. And I would send you my tar ball about filo in Etherboot. Regards YH -----邮件原件----- 发件人: Jay Miller [mailto:jmiller@actuality-systems.com] 发送时间: 2004年5月13日 8:36 收件人: linuxbios(a)clustermatic.org 主题: Making payloads The reason why my S2885 image wasn't working is because my system only has 1 CPU populated. A little tweaking to remove the second processor and I can get FILO to come up. Unfortunately FILO does not detect the IDE disk. I noticed in the payloads section of Config.lb there are some multi-part payloads, like tg3--ide_disk.zelf, and tg3--filo.zelf. How do I create the multi-part payloads? Ideally I would be interested in a FILO that recognizes IDE. Alternatively I am also pursuing a tg3 payload that will load my kernel over the network. Thanks, Jay Miller Actuality Systems, Inc. jmiller(a)acutality-systems.com _______________________________________________ Linuxbios mailing list Linuxbios(a)clustermatic.org http://www.clustermatic.org/mailman/listinfo/linuxbios _______________________________________________ Linuxbios mailing list Linuxbios(a)clustermatic.org http://www.clustermatic.org/mailman/listinfo/linuxbios

1 0

RE: Making payloads
by Jay Miller 13 May '04

13 May '04

I built tg3--filo.zelf with the latest patch from the link in your message. Getting the follow error message when loading: Loading Etherboot version: 5.2.4 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x4aef5 offset 0xb0 filesize 0xa4b7 (cleaned up) New segment addr 0x20000 size 0x4aef5 offset 0xb0 filesize 0xa4b7 Loading Segment: addr: 0x000000001ffadfe8 memsz: 0x000000000001b00c filesz: 0x00 0000000000a4b7 Clearing Segment: addr: 0x000000001ffb849f memsz: 0x0000000000010b55 Loading Segment: addr: 0x000000000003b00c memsz: 0x000000000002fee9 filesz: 0x00 00000000000000 39:stream_skip() - overflowed source buffer ERROR: Skip of 68437 bytes skiped 23193 bytes Cannot Load ELF Image What am I doing wrong? -J -----Original Message----- From: YhLu [mailto:YhLu@tyan.com] Sent: Thursday, May 13, 2004 1:22 PM To: Jay Miller; linuxbios(a)clustermatic.org Subject: 答复: Making payloads http://sourceforge.net/tracker/index.php?func=detail&aid=943300&group_id=423 3&atid=304233 -----邮件原件----- 发件人: YhLu 发送时间: 2004年5月13日 10:05 收件人: Jay Miller; linuxbios(a)clustermatic.org 主题: 答复: Making payloads Jay, I have merged into FILO into Etherboot. You can get that patch from Etherboot group. So you can build tg3--filo.zelf. About the PCI scan in Etherboot has no problem to find IDE other than bus 0. Current it already supports serial IDE and normal IDE. I'm working on add usb boot into FILO in Etherboot. The AMD8111 is using OHCI, and I'm trying to make use steven code for USB boot, but it is only support UHCI. OHCI has hardware support for ED (QH) instead of SW QH. Maybe I need to get UHCI addon card at first. Please let me know if you has problem to get filo patch. And I would send you my tar ball about filo in Etherboot. Regards YH -----邮件原件----- 发件人: Jay Miller [mailto:jmiller@actuality-systems.com] 发送时间: 2004年5月13日 8:36 收件人: linuxbios(a)clustermatic.org 主题: Making payloads The reason why my S2885 image wasn't working is because my system only has 1 CPU populated. A little tweaking to remove the second processor and I can get FILO to come up. Unfortunately FILO does not detect the IDE disk. I noticed in the payloads section of Config.lb there are some multi-part payloads, like tg3--ide_disk.zelf, and tg3--filo.zelf. How do I create the multi-part payloads? Ideally I would be interested in a FILO that recognizes IDE. Alternatively I am also pursuing a tg3 payload that will load my kernel over the network. Thanks, Jay Miller Actuality Systems, Inc. jmiller(a)acutality-systems.com _______________________________________________ Linuxbios mailing list Linuxbios(a)clustermatic.org http://www.clustermatic.org/mailman/listinfo/linuxbios _______________________________________________ Linuxbios mailing list Linuxbios(a)clustermatic.org http://www.clustermatic.org/mailman/listinfo/linuxbios

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot