coreboot November 2007

coreboot@coreboot.org

75 participants
397 discussions

[LinuxBIOS] [patch] Fix M57SLI interrupt routing
by Torsten Duwe 12 Nov '07

12 Nov '07

This patch makes both PCI slots and the primary PCIe work for me, sort of. The only downsides are that under heavy usage I lose an interrupt once in a while, but this might be due to irqpoll. The other issue is that the graphics card still only initialises under X, and still very slowly. Looking at mptable.c I get the impression it was copied almost verbatim from another board and not adopted to the M57SLI. Yinghai, where did you get the routing info from? Another scary thing is that the wiring seems to differ when the board is set up via LinuxBIOS; legacy BIOS puts the PCIe 16x int A on the same line with bus 1 device 8, while LinuxBIOS does that with bus 1 device 7 ! Can anyone with a datasheet shed some light on this? Anyway, here's the patch that improves things quite a lot on my machine. please SVN-quote only below this line :-) ------------------------------------------------------------------------------------------ Fix the M57SLI routing table, as apparently set up from LinuxBIOS on that board. Shift PCIe pin numbers downwards, and PCI int pins upwards. This puts both PCI slots' int A and PCIe 16x int A into the right position. Signed-off-by: Torsten Duwe <duwe(a)lst.de>

6 12

[LinuxBIOS] r2956 build service
by LinuxBIOS information 12 Nov '07

12 Nov '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "uwe" checked in revision 2956 to the LinuxBIOS source repository and caused the following changes: Change Log: Drop superfluous exit_conf_mode*() calls, we don't want to call them twice. Small cosmetic fixes (trivial). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Build Log: Compilation of agami:aruma is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2956&device=aruma&vendor=… Compilation of amd:serengeti_cheetah is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2956&device=serengeti_che… Compilation of asus:a8v-e_se is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2956&device=a8v-e_se&vend… Compilation of iwill:dk8_htx is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2956&device=dk8_htx&vendo… If something broke during this checkin please be a pain in uwe's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

1 0

[LinuxBIOS] IT8705F/AF superiotool dump
by Frieder Ferlemann 12 Nov '07

12 Nov '07

Hi, this is a superiotool dump of a PCCHIPS M848A Rev2.1 mainboard. It was mentioned here, that this might be missing: http://linuxbios.org/pipermail/linuxbios/2007-October/025414.html (Seems to be found both at 0x2e and at 0x4e. Most lines have a trailing white space) Greetings, Frieder -------8<-------------------------------------------------- superiotool r2922 Found ITE IT8705F/AF / IT8700F (id=0x8705, rev=0x2) at 0x2e Register dump: idx 07 20 21 22 23 24 val 08 87 05 02 00 f0 def NA 87 05 00 00 NA LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 80 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 00 03 f8 04 00 LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 00 00 00 00 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 64 65 70 74 f0 val 01 03 78 07 78 00 80 07 03 0a def 00 03 78 07 78 00 80 07 03 03 LDN 0x04 (Environment controller) idx 2b 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 00 01 02 90 02 30 00 80 00 00 00 40 00 ff def 00 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (GPIO) idx 25 26 27 28 29 2a 60 61 62 63 64 65 70 71 72 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc cd d0 d1 d2 d3 d4 d5 d6 d8 d9 da f0 f1 f2 f5 f6 f7 f8 f9 fa fb fc fd fe ff val 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 00 def 00 00 00 ff e0 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x06 (Game port) idx 30 60 61 val 00 00 00 def 00 02 01 LDN 0x07 (Consumer IR) idx 30 60 61 70 f0 val 00 00 00 00 06 def 00 03 10 0b 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 00 00 00 00 def 00 03 00 0a 00 Found ITE IT8705F/AF / IT8700F (id=0x8705, rev=0x2) at 0x4e Register dump: idx 07 20 21 22 23 24 val 08 87 05 02 00 f0 def NA 87 05 00 00 NA LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 80 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 00 03 f8 04 00 LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 00 00 00 00 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 64 65 70 74 f0 val 01 03 78 07 78 00 80 07 03 0a def 00 03 78 07 78 00 80 07 03 03 LDN 0x04 (Environment controller) idx 2b 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 00 01 02 90 02 30 00 80 00 00 00 40 00 ff def 00 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (GPIO) idx 25 26 27 28 29 2a 60 61 62 63 64 65 70 71 72 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc cd d0 d1 d2 d3 d4 d5 d6 d8 d9 da f0 f1 f2 f5 f6 f7 f8 f9 fa fb fc fd fe ff val 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 00 def 00 00 00 ff e0 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x06 (Game port) idx 30 60 61 val 00 00 00 def 00 02 01 LDN 0x07 (Consumer IR) idx 30 60 61 70 f0 val 00 00 00 00 06 def 00 03 10 0b 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 00 00 00 00 def 00 03 00 0a 00 superiotool r2922 Found ITE IT8705F/AF / IT8700F (id=0x8705, rev=0x2) at 0x2e Register dump: idx 07 20 21 22 23 24 val 08 87 05 02 00 f0 def NA 87 05 00 00 NA LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 80 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 00 03 f8 04 00 LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 00 00 00 00 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 64 65 70 74 f0 val 01 03 78 07 78 00 80 07 03 0a def 00 03 78 07 78 00 80 07 03 03 LDN 0x04 (Environment controller) idx 2b 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 00 01 02 90 02 30 00 80 00 00 00 40 00 ff def 00 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (GPIO) idx 25 26 27 28 29 2a 60 61 62 63 64 65 70 71 72 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc cd d0 d1 d2 d3 d4 d5 d6 d8 d9 da f0 f1 f2 f5 f6 f7 f8 f9 fa fb fc fd fe ff val 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 00 def 00 00 00 ff e0 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x06 (Game port) idx 30 60 61 val 00 00 00 def 00 02 01 LDN 0x07 (Consumer IR) idx 30 60 61 70 f0 val 00 00 00 00 06 def 00 03 10 0b 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 00 00 00 00 def 00 03 00 0a 00 Found ITE IT8705F/AF / IT8700F (id=0x8705, rev=0x2) at 0x4e Register dump: idx 07 20 21 22 23 24 val 08 87 05 02 00 f0 def NA 87 05 00 00 NA LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 val 01 03 f0 06 02 00 80 def 00 03 f0 06 02 00 00 LDN 0x01 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 00 03 f8 04 00 LDN 0x02 (COM2) idx 30 60 61 70 f0 f1 f2 f3 val 00 00 00 00 00 50 00 7f def 00 02 f8 03 00 50 00 7f LDN 0x03 (Parallel port) idx 30 60 61 62 63 64 65 70 74 f0 val 01 03 78 07 78 00 80 07 03 0a def 00 03 78 07 78 00 80 07 03 03 LDN 0x04 (Environment controller) idx 2b 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 val 00 01 02 90 02 30 00 80 00 00 00 40 00 ff def 00 00 02 90 02 30 09 00 00 00 00 00 NA NA LDN 0x05 (GPIO) idx 25 26 27 28 29 2a 60 61 62 63 64 65 70 71 72 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc cd d0 d1 d2 d3 d4 d5 d6 d8 d9 da f0 f1 f2 f5 f6 f7 f8 f9 fa fb fc fd fe ff val 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0f 00 def 00 00 00 ff e0 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 LDN 0x06 (Game port) idx 30 60 61 val 00 00 00 def 00 02 01 LDN 0x07 (Consumer IR) idx 30 60 61 70 f0 val 00 00 00 00 06 def 00 03 10 0b 00 LDN 0x08 (MIDI port) idx 30 60 61 70 f0 val 00 00 00 00 00 def 00 03 00 0a 00

2 11

[LinuxBIOS] r2956 - trunk/util/superiotool
by svn＠openbios.org 12 Nov '07

12 Nov '07

Author: uwe Date: 2007-11-12 22:02:44 +0100 (Mon, 12 Nov 2007) New Revision: 2956 Modified: trunk/util/superiotool/ali.c trunk/util/superiotool/fintek.c trunk/util/superiotool/ite.c trunk/util/superiotool/nsc.c trunk/util/superiotool/smsc.c trunk/util/superiotool/winbond.c Log: Drop superfluous exit_conf_mode*() calls, we don't want to call them twice. Small cosmetic fixes (trivial). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/util/superiotool/ali.c =================================================================== --- trunk/util/superiotool/ali.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/ali.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -95,4 +95,3 @@ exit_conf_mode_ali(port); } - Modified: trunk/util/superiotool/fintek.c =================================================================== --- trunk/util/superiotool/fintek.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/fintek.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -99,4 +99,3 @@ exit_conf_mode_winbond_fintek_ite_8787(port); } - Modified: trunk/util/superiotool/ite.c =================================================================== --- trunk/util/superiotool/ite.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/ite.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -360,7 +360,6 @@ if (superio_unknown(reg_table, id)) { if (verbose) printf(NOTFOUND "id=0x%04x, rev=0x%01x\n", id, chipver); - exit_conf_mode_ite(port); return; } @@ -381,4 +380,3 @@ probe_idregs_ite_helper("(init=0x87,0x87) ", port); exit_conf_mode_winbond_fintek_ite_8787(port); } - Modified: trunk/util/superiotool/nsc.c =================================================================== --- trunk/util/superiotool/nsc.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/nsc.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -170,4 +170,3 @@ dump_superio("NSC", reg_table, port, id); } - Modified: trunk/util/superiotool/smsc.c =================================================================== --- trunk/util/superiotool/smsc.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/smsc.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -390,4 +390,3 @@ probe_idregs_smsc_helper(port, DEVICE_ID_REG, DEVICE_REV_REG); probe_idregs_smsc_helper(port, DEVICE_ID_REG_OLD, DEVICE_REV_REG_OLD); } - Modified: trunk/util/superiotool/winbond.c =================================================================== --- trunk/util/superiotool/winbond.c 2007-11-12 11:14:10 UTC (rev 2955) +++ trunk/util/superiotool/winbond.c 2007-11-12 21:02:44 UTC (rev 2956) @@ -414,7 +414,6 @@ if (verbose) printf(NOTFOUND "id/oldid=0x%02x/0x%02x, rev=0x%02x\n", devid, olddevid, rev); - exit_conf_mode_winbond_fintek_ite_8787(port); return; } @@ -450,4 +449,3 @@ probe_idregs_winbond_helper("(init=0x87,0x87) ", port); exit_conf_mode_winbond_fintek_ite_8787(port); } -

1 0

[LinuxBIOS] r2954 build service
by LinuxBIOS information 12 Nov '07

12 Nov '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "cozzie" checked in revision 2954 to the LinuxBIOS source repository and caused the following changes: Change Log: Try to fix a few loose ends on the GA-M57SLI Super I/O GPIO configuration. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Torsten Duwe <duwe(a)lst.de> Build Log: Compilation of agami:aruma has been broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2954&device=aruma&vendor=… Compilation of amd:serengeti_cheetah has been broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2954&device=serengeti_che… Compilation of asus:a8v-e_se has been broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2954&device=a8v-e_se&vend… Compilation of iwill:dk8_htx has been broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2954&device=dk8_htx&vendo… If something broke during this checkin please be a pain in cozzie's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

2 1

[LinuxBIOS] Question about a specific board
by rrodriguez＠astrocorp.com 12 Nov '07

12 Nov '07

Hello LinuxBIOS mailing list I am wondering if this board http://www.ibase-i.com.tw/ib798.htm would work with LinuxBIOSv2 or if it is only partially supported? really I'm asking how much work would be involved in getting this board working? Yes i see some parts of it are listed on your site but we are not sure on how well or how much time we will need to spend on getting it working. Thank you! -- Ryan Rodriguez Astrocom Corporation http://www.astrocorp.com/

2 1

[LinuxBIOS] r2955 build service
by LinuxBIOS information 12 Nov '07

12 Nov '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "hailfinger" checked in revision 2955 to the LinuxBIOS source repository and caused the following changes: Change Log: Fix the remaining issues with GA-M57SLI Super I/O GPIO configuration. With this patch, flashing the parallel EEPROM on board revisions 1.x finally works. Flashing the serial EEPROM of board revisions 2.x is just one patch away. Torsten Duwe says: Flash erase on my board was failing reliably. Now it works! Andreas B. Mundt says: For the first time I was able to write with flashrom and LB. $flashrom -Vv --write linuxbios.rom [...] Vendor ID: GIGABYTE, part ID: m57sli Found chipset "NVIDIA MCP55", enabling flash write... OK. [...] SST49LF040B found at physical address 0xfff80000. Flash part is SST49LF040B (512 KB). LinuxBIOS last image size (not ROM size) is 4096 bytes. Manufacturer: GIGABYTE Mainboard ID: m57sli This firmware image matches this motherboard. Programming page: 0007 at address: 0x00070000 Verifying flash... VERIFIED. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Torsten Duwe <duwe(a)lst.de> Tested-by: Andreas B. Mundt <andi.mundt(a)web.de> Tested-by: Torsten Duwe <duwe(a)lst.de> Build Log: Compilation of agami:aruma is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2955&device=aruma&vendor=… Compilation of amd:serengeti_cheetah is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2955&device=serengeti_che… Compilation of asus:a8v-e_se is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2955&device=a8v-e_se&vend… Compilation of iwill:dk8_htx is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2955&device=dk8_htx&vendo… If something broke during this checkin please be a pain in hailfinger's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

1 0

[LinuxBIOS] r2955 - in trunk/LinuxBIOSv2/src: mainboard/gigabyte/m57sli superio/ite/it8716f
by svn＠openbios.org 12 Nov '07

12 Nov '07

Author: hailfinger Date: 2007-11-12 12:14:10 +0100 (Mon, 12 Nov 2007) New Revision: 2955 Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h trunk/LinuxBIOSv2/src/superio/ite/it8716f/superio.c Log: Fix the remaining issues with GA-M57SLI Super I/O GPIO configuration. With this patch, flashing the parallel EEPROM on board revisions 1.x finally works. Flashing the serial EEPROM of board revisions 2.x is just one patch away. Torsten Duwe says: Flash erase on my board was failing reliably. Now it works! Andreas B. Mundt says: For the first time I was able to write with flashrom and LB. $flashrom -Vv --write linuxbios.rom [...] Vendor ID: GIGABYTE, part ID: m57sli Found chipset "NVIDIA MCP55", enabling flash write... OK. [...] SST49LF040B found at physical address 0xfff80000. Flash part is SST49LF040B (512 KB). LinuxBIOS last image size (not ROM size) is 4096 bytes. Manufacturer: GIGABYTE Mainboard ID: m57sli This firmware image matches this motherboard. Programming page: 0007 at address: 0x00070000 Verifying flash... VERIFIED. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Torsten Duwe <duwe(a)lst.de> Tested-by: Andreas B. Mundt <andi.mundt(a)web.de> Tested-by: Torsten Duwe <duwe(a)lst.de> Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-11-12 02:33:31 UTC (rev 2954) +++ trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-11-12 11:14:10 UTC (rev 2955) @@ -282,17 +282,17 @@ # pin 13 is GP35 irq 0x27 = 0x20 # pin 70 is not GP46 - #0x28 = 0x0 + #irq 0x28 = 0x0 # pin 6,3,128,127,126 is GP63,64,65,66,67 irq 0x29 = 0x81 # Enable FAN_CTL/FAN_TAC set to 5 (pin 21,23), enable FAN_CTL/FAN_TAC set to 4 (pin 20,22), pin 48 is PCIRST5#, pin91 is PCIRSTIN#, VIN7 is internal voltage divider for VCCH5V, pin 95 is ATXPG, VIN3 is internal voltage divider for VCC5V - #0x2c = 0x1f + #irq 0x2c = 0x1f # Simple I/O base io 0x62 = 0x800 # Serial Flash I/O (SPI only) #io 0x64 = 0x820 # watch dog force timeout (parallel flash only) - #0x71 = 0x1 + #irq 0x71 = 0x1 # No WDT interrupt irq 0x72 = 0x0 # GPIO pin set 1 disable internal pullup @@ -300,23 +300,23 @@ # GPIO pin set 5 enable internal pullup irq 0xbc = 0x01 # SIO pin set 1 alternate function - #0xc0 = 0x0 + #irq 0xc0 = 0x0 # SIO pin set 2 mixed function irq 0xc1 = 0x43 # SIO pin set 3 mixed function irq 0xc2 = 0x20 # SIO pin set 4 alternate function - #0xc3 = 0x0 + #irq 0xc3 = 0x0 # SIO pin set 1 input mode - #0xc8 = 0x0 + #irq 0xc8 = 0x0 # SIO pin set 2 mixed input/output mode irq 0xc9 = 0x0 # SIO pin set 4 input mode - #0xcb = 0x0 + #irq 0xcb = 0x0 # Generate SMI# on EC IRQ - #0xf0 = 0x10 + #irq 0xf0 = 0x10 # SMI# level trigger - #0xf1 = 0x40 + #irq 0xf1 = 0x40 # HWMON alert beep pin location irq 0xf6 = 0x28 end Modified: trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h =================================================================== --- trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h 2007-11-12 02:33:31 UTC (rev 2954) +++ trunk/LinuxBIOSv2/src/superio/ite/it8716f/it8716f.h 2007-11-12 11:14:10 UTC (rev 2955) @@ -28,6 +28,7 @@ #define IT8716F_EC 0x04 /* Environment controller */ #define IT8716F_KBCK 0x05 /* Keyboard */ #define IT8716F_KBCM 0x06 /* Mouse */ +#define IT8716F_GPIO 0x07 /* GPIO */ #define IT8716F_MIDI 0x08 /* MIDI port */ #define IT8716F_GAME 0x09 /* GAME port */ #define IT8716F_IR 0x0a /* Consumer IR */ Modified: trunk/LinuxBIOSv2/src/superio/ite/it8716f/superio.c =================================================================== --- trunk/LinuxBIOSv2/src/superio/ite/it8716f/superio.c 2007-11-12 02:33:31 UTC (rev 2954) +++ trunk/LinuxBIOSv2/src/superio/ite/it8716f/superio.c 2007-11-12 11:14:10 UTC (rev 2955) @@ -152,7 +152,7 @@ {&ops, IT8716F_KBCK, PNP_IO0 | PNP_IO1 | PNP_IRQ0, {0x7ff, 0}, {0x7ff, 0x4},}, {&ops, IT8716F_KBCM, PNP_IRQ0,}, - // No 7 { 0,}, + {&ops, IT8716F_GPIO,}, {&ops, IT8716F_MIDI, PNP_IO0 | PNP_IRQ0, {0x7fe, 0x4},}, {&ops, IT8716F_GAME, PNP_IO0, {0x7ff, 0},}, {&ops, IT8716F_IR,},

1 0

[LinuxBIOS] mkelfImage - how to use the resultant image?
by Baski 12 Nov '07

12 Nov '07

I used mkElfImage ver 2.7 to create a single bootable elf image with this syntax sudo mkelfImage --command-line="ro root=/dev/hd1 quiet splash console=tty0 console=ttyS0,115200n8" --kernel=/boot/vmlinuz-2.6.20-16-generic --initrd=/boot/initrd.img-2.6.20-16-generic --output=/boot/linuxTest_2.6-generic.elf The resultant image is about 8MB (ubuntu). Because of the size I think we cannot flash it on the bios chip. How do I use this image in linuxbios to boot the OS? Not finding much documentaion on this. Currently I'm using FILO as my payload. Thanks -Baski __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

2 1

[LinuxBIOS] r2954 - trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli
by svn＠openbios.org 12 Nov '07

12 Nov '07

Author: cozzie Date: 2007-11-12 03:33:31 +0100 (Mon, 12 Nov 2007) New Revision: 2954 Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb Log: Try to fix a few loose ends on the GA-M57SLI Super I/O GPIO configuration. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Torsten Duwe <duwe(a)lst.de> Modified: trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-11-08 02:28:43 UTC (rev 2953) +++ trunk/LinuxBIOSv2/src/mainboard/gigabyte/m57sli/Config.lb 2007-11-12 02:33:31 UTC (rev 2954) @@ -239,7 +239,12 @@ device pci 0.0 on end # HT device pci 1.0 on # LPC chip superio/ite/it8716f - device pnp 2e.0 off # Floppy + # Floppy and any LDN + device pnp 2e.0 off + # Watchdog from CLKIN, CLKIN = 24 MHz + irq 0x23 = 0x11 + # Serial Flash (SPI only) + #0x24 = 0x1a io 0x60 = 0x3f0 irq 0x70 = 6 drq 0x74 = 2 @@ -269,6 +274,52 @@ device pnp 2e.6 on # Mouse irq 0x70 = 12 end + device pnp 2e.7 on # GPIO, SPI flash + # pin 84 is not GP10 + irq 0x25 = 0x0 + # pin 21 is GP26, pin 26 is GP21, pin 27 is GP20 + irq 0x26 = 0x43 + # pin 13 is GP35 + irq 0x27 = 0x20 + # pin 70 is not GP46 + #0x28 = 0x0 + # pin 6,3,128,127,126 is GP63,64,65,66,67 + irq 0x29 = 0x81 + # Enable FAN_CTL/FAN_TAC set to 5 (pin 21,23), enable FAN_CTL/FAN_TAC set to 4 (pin 20,22), pin 48 is PCIRST5#, pin91 is PCIRSTIN#, VIN7 is internal voltage divider for VCCH5V, pin 95 is ATXPG, VIN3 is internal voltage divider for VCC5V + #0x2c = 0x1f + # Simple I/O base + io 0x62 = 0x800 + # Serial Flash I/O (SPI only) + #io 0x64 = 0x820 + # watch dog force timeout (parallel flash only) + #0x71 = 0x1 + # No WDT interrupt + irq 0x72 = 0x0 + # GPIO pin set 1 disable internal pullup + irq 0xb8 = 0x0 + # GPIO pin set 5 enable internal pullup + irq 0xbc = 0x01 + # SIO pin set 1 alternate function + #0xc0 = 0x0 + # SIO pin set 2 mixed function + irq 0xc1 = 0x43 + # SIO pin set 3 mixed function + irq 0xc2 = 0x20 + # SIO pin set 4 alternate function + #0xc3 = 0x0 + # SIO pin set 1 input mode + #0xc8 = 0x0 + # SIO pin set 2 mixed input/output mode + irq 0xc9 = 0x0 + # SIO pin set 4 input mode + #0xcb = 0x0 + # Generate SMI# on EC IRQ + #0xf0 = 0x10 + # SMI# level trigger + #0xf1 = 0x40 + # HWMON alert beep pin location + irq 0xf6 = 0x28 + end device pnp 2e.8 off # MIDI io 0x60 = 0x300 irq 0x70 = 10 @@ -305,6 +356,7 @@ device i2c 57 on end end end # SM +#WTF?!? We already have device pci 1.1 in the section above device pci 1.1 on # SM 1 #PCI device smbus address will depend on addon pci device, do we need to scan_smbus_bus? # chip drivers/generic/generic #PCIXA Slot1

1 0

← Newer
1
...
26
27
28
29
30
31
32
...
40
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot November 2007