coreboot June 2006

coreboot@coreboot.org

31 participants
49 discussions

Re: [LinuxBIOS] Support for AM2 processors?
by Lu, Yinghai 18 Jun '06

18 Jun '06

The support code is done, and will be released to public tree after the CPU is released to public. YH -----Original Message----- From: linuxbios-bounces(a)linuxbios.org [mailto:linuxbios-bounces@linuxbios.org] On Behalf Of Carl-Daniel Hailfinger Sent: Wednesday, April 19, 2006 4:35 PM To: linuxbios(a)linuxbios.org Subject: [LinuxBIOS] Support for AM2 processors? Hi, since the upcoming AM2 processors will have a new (DDR2) memory controller, does that mean the RAM initialization has to be rewritten completely? If so, is there any expected time when LinuxBIOS support for these processors will be available? Regards, Carl-Daniel -- http://www.hailfinger.org/ -- linuxbios mailing list linuxbios(a)linuxbios.org http://www.openbios.org/mailman/listinfo/linuxbios

2 1

Re: [LinuxBIOS] EPIA-MII 12000, almost there. ( newbie )
by Richard Smith 14 Jun '06

14 Jun '06

On 6/14/06, Per Mellander <per(a)mellander.org> wrote: > Thank you, thank you, thank you for those words! > > I was nearly giving up today after trying 64k of zero's instead of VGA and nothing > worked. I was almost certain that I'm to stupid to do this ;) Hmm... That should have worked. The issue is that the buildsystem is creating a rom file that is 64k shy of the size of your ROM part. So all the addresses in the part will all be 64k lower than where they need to be. You can solve this by either prepending 64k data that bumps the size of the rom file up to the size of the rom part, or program the file into the part with a 64k offset. So regardless if you used 0x00's, 0xff, or random bytes you should still get _some_ serial output if the size is correct. You can check your rom file with the following. 'hd -s 255k <romfile>' If you don't see an 0xe9 at address 0x0003fff0 then your rom file is not valid. -- Richard A. Smith

1 0

Re: [LinuxBIOS] EPIA-MII 12000, almost there. ( newbie )
by Myles Watson 13 Jun '06

13 Jun '06

I used the stock FC4 kernel with the same command line as you used. My autoboot was just hdb1:/linux_2.6.16.elf (I have a CD-ROM as hda) Good luck, Myles -----Original Message----- From: linuxbios-bounces(a)linuxbios.org [mailto:linuxbios-bounces@linuxbios.org] On Behalf Of Per Mellander Sent: Wednesday, May 31, 2006 6:53 AM To: myles(a)mouselemur.cs.byu.edu Cc: linuxbios(a)linuxbios.org Subject: Re: [LinuxBIOS] EPIA-MII 12000, almost there. ( newbie ) Now I get so far that the kernel is identified and loaded but then it breaks :( I created an elf with mkelfImage: # mkelfImage --kernel=/vmlinuz-2.6.16-1.2111_FC5 --output=/vmlinuz.elf --initrd=/initrd-2.6.16-1.2111_FC5.img --command-line="ro root=LABEL=/ rhgb quiet console=ttyS0 console=ttyS0,115200" ----8<------------------------------------------------------------- Jumping to boot code at 0x109ad4 FILO version 0.5 (root(a)mm.int.mmtab.se) Wed May 31 13:44:15 CEST 2006 Press <Enter> for default boot, or <Esc> for boot prompt... timed out boot: hda1:/vmlinuz.elf find_ide_controller: found PCI IDE controller 1106:0571 prog_if=0x8a find_ide_controller: primary channel: compatibility mode find_ide_controller: cmd_base=0x1f0 ctrl_base=0x3f4 ide_software_reset: Waiting for ide0 to become ready for reset... ok init_drive: Testing for hda init_drive: Probing for hda init_drive: LBA mode, sectors=268435455 init_drive: LBA48 mode, sectors=321672960 init_drive: Init device params... ok hda: LBA48 164GB: HDS722516VLAT80 Mounted ext2fs Loading Linux version 2.6.16-1.2111_FC5 (bhcompile(a)hs20-bc1-3.build.redhat.com) #1 Thu May 4 21:16:58 EDT 2006... Jumping to entry point... 0 LinuxBIOS-1.1.8.0Fallback Wed May 31 13:15:25 CEST 2006 starting... Enabling mainboard devices Enabling shadow ram ----8<------------------------------------------------------------- I get the same result when I try, AUTOBOOT_FILE = "hda1:/vmlinuz initrd=/initrd.img root=/dev/hda1 console=tty0 console=ttyS0,115200" so the problem is not in the elf image. Could you please send me a snippet from your AUTOBOOT or similar? Btw. Do I have to make a 'special' kernel to make this work or should the stock FC5 work? /Per On Tue, 30 May 2006 08:38:53 -0600, Myles Watson wrote > Did you try using mkelfImage from ftp://ftp.lnxi.com/pub/mkelfImage ? It > combines the vmlinuz & initrd files into one. > > To get my machine to boot I used the same kernel parameters as I found in > grub, set up by Fedora. > -- linuxbios mailing list linuxbios(a)linuxbios.org http://www.openbios.org/mailman/listinfo/linuxbios

6 18

[LinuxBIOS] To Stephan
by steve yannalfo 13 Jun '06

13 Jun '06

Thank you, ------------------------------------------------------------------------- added in "etherboot.h" #ifndef LINUXBIOS extern void allot_real_mode_stack(void); #endif # make clean && make bin/filo.elf OK -------------------------------------------------------------------------- in "ck804_early_setup_car.c" added line 482: hard_reset(); FIXED soft/hard reset differences where LB would stop (soft reset only) PCI: 00:00.0 cmd <- 146 -------------------------------------------------------------------------- steve __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

1 0

Re: [LinuxBIOS] etherboot fails to compile for FILO
by steve yannalfo 13 Jun '06

13 Jun '06

Same Problem: cc -DCONFIG_PCI -DCONFIG_ISA -DASK_BOOT=3 -DBOOT_FIRST=BOOT_NIC -DCONFIG_FILO -DALLOW_ONLY_ENCAPSULATED -DBACKOFF_LIMIT=7 -DCONGESTED -DTAGGED_IMAGE -DELF_IMAGE -DDOWNLOAD_PROTO_TFTP -Os In file included from arch/i386/core/realmode.c:7: arch/i386/include/realmode.h:119: error: static declaration of 'allot_real_mode_stack' follows non-static declaration include/etherboot.h:330: error: previous declaration of 'allot_real_mode_stack' was here make: *** [bin/realmode.o] Error 1 Thank You. steve __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

2 1

[LinuxBIOS] etherboot fails to compile for FILO
by steve yannalfo 13 Jun '06

13 Jun '06

ld -m elf_i386 -N -T arch/i386/core/etherboot.lds -o bin/filo.elf.rt bin/elfprefix.exit.o bin/filo.rt.o bin/filo.rt.o: In function `install_pxe_stack': : undefined reference to `allot_base_memory' bin/filo.rt.o: In function `install_pxe_stack': : undefined reference to `e820mangler_size' bin/filo.rt.o: In function `install_pxe_stack': : undefined reference to `install_rm_callback_interface' bin/filo.rt.o: In function `install_pxe_stack': : undefined reference to `install_e820mangler' bin/filo.rt.o: In function `use_undi_ds_for_rm_stack': : undefined reference to `forget_real_mode_stack' bin/filo.rt.o: In function `hook_pxe_stack': : undefined reference to `hide_etherboot' bin/filo.rt.o: In function `unhook_pxe_stack': : undefined reference to `unhide_etherboot' bin/filo.rt.o: In function `remove_pxe_stack': : undefined reference to `forget_base_memory' bin/filo.rt.o: In function `pxenv_restart_tftp': : undefined reference to `get_free_base_memory' make: *** [bin/filo.elf.rt] Error 1 rm bin/elfprefix.entry.o bin/filo.rt.o bin/elfprefix.exit.o bin/filo.o ---------------------------------------------------------------------------------------------------- src/Config # Select which buses etherboot should support CFLAGS+= -DCONFIG_PCI CFLAGS+= -DCONFIG_ISA # CFLAGS+= -DCONFIG_PCMCIA # For prompting and default on timeout CFLAGS+= -DASK_BOOT=3 -DBOOT_FIRST=BOOT_NIC # If you would like to attempt to boot from other devices as well as the network. # CFLAGS+= -DBOOT_SECOND=BOOT_FLOPPY # CFLAGS+= -DBOOT_THIRD=BOOT_DISK # CFLAGS+= -DBOOT_INDEX=0 # If you prefer the old style rotating bar progress display # CFLAGS+= -DBAR_PROGRESS # Show size indicator # CFLAGS+= -DSIZEINDICATOR # Enabling this creates non-standard images which use ports 1067 and 1068 # for DHCP/BOOTP # CFLAGS+= -DALTERNATE_DHCP_PORTS_1067_1068 # Enabling this makes the boot ROM require a Vendor Class Identifier # of "Etherboot" in the Vendor Encapsulated Options # This can be used to reject replies from servers other than the one # we want to give out addresses to us, but it will prevent Etherboot # from getting an IP lease until you have configured DHCPD correctly # CFLAGS+= -DREQUIRE_VCI_ETHERBOOT # EXPERIMENTAL! Set DHCP_CLIENT_ID to create a Client Identifier (DHCP # option 61, see RFC2132 section 9.14) when Etherboot sends the DHCP # DISCOVER and REQUEST packets. This ID must UNIQUELY identify each # client on your local network. Set DHCP_CLIENT_ID_TYPE to the # appropriate hardware type as described in RFC2132 / RFC1700; this # almost certainly means using '1' if the Client ID is an Ethernet MAC # address and '0' otherwise. Set DHCP_CLIENT_ID_LEN to the length of # the Client ID in octets (this is not a null terminated C string, do # NOT add 1 for a terminator and do NOT add an extra 1 for the # hardware type octet). Note that to identify your client using the # normal default MAC address of your NIC, you do NOT need to set this # option, as the MAC address is automatically used in the # hwtype/chaddr field; note also that this field only sets the DHCP # option: it does NOT change the MAC address used by the client. # CFLAGS+= -DDHCP_CLIENT_ID="'C','L','I','E','N','T','0','0','1'" \ # -DDHCP_CLIENT_ID_LEN=9 -DDHCP_CLIENT_ID_TYPE=0 # CFLAGS+= -DDHCP_CLIENT_ID="0xDE,0xAD,0xBE,0xEF,0xDE,0xAD" \ # -DDHCP_CLIENT_ID_LEN=6 -DDHCP_CLIENT_ID_TYPE=1 # EXPERIMENTAL! Set DHCP_USER_CLASS to create a User Class option (see # RFC3004) when Etherboot sends the DHCP DISCOVER and REQUEST packets. # This can be used for classification of clients, typically so that a # DHCP server can send an appropriately tailored reply. Normally, a # string identifies a class of to which this client instance belongs # which is useful in your network, such as a department ('FINANCE' or # 'MARKETING') or hardware type ('THINCLIENT' or 'KIOSK'). Set # DHCP_USER_CLASS_LEN to the length of DHCP_USER_CLASS in octets. # This is NOT a null terminated C string, do NOT add 1 for a # terminator. RFC3004 advises how to lay out multiple User Class # options by using an octet for the length of each string, as in this # example. It is, of course, up to the server to parse this. # CFLAGS+= -DDHCP_USER_CLASS="'T','E','S','T','C','L','A','S','S'" \ # -DDHCP_USER_CLASS_LEN=9 # CFLAGS+= -DDHCP_USER_CLASS="5,'A','L','P','H','A',4,'B','E','T','A'" \ # -DDHCP_USER_CLASS_LEN=11 # for btext console support # CFLAGS+= -DCONSOLE_BTEXT # for direct PC kbd support # CFLAGS+= -DCONSOLE_PC_KBD # Set to enable FILO support # for FILO support it will make main call pci_init INCLUDE_FILO=y ifdef INCLUDE_FILO CFLAGS+= -DCONFIG_FILO endif # Enabling this causes Etherboot to ignore Etherboot-specific options # that are not within an Etherboot encapsulated options field. # This option should be enabled unless you have a legacy DHCP server # configuration from the bad old days before the use of # encapsulated Etherboot options. CFLAGS+= -DALLOW_ONLY_ENCAPSULATED # Disable DHCP support # CFLAGS+= -DNO_DHCP_SUPPORT # Set to enable static boot information # CFLAGS+= -DUSE_STATIC_BOOT_INFO # Specify the static boot values # All must be specified, if -DUSE_STATIC_BOOT_INFO is defined # CFLAGS+= -DSTATIC_CLIENT_IP=\"192.168.25.25\" # CFLAGS+= -DSTATIC_SUBNET_MASK=\"255.255.255.0\" # CFLAGS+= -DSTATIC_SERVER_IP=\"192.168.25.101\" # CFLAGS+= -DSTATIC_GATEWAY_IP=\"192.168.25.1\" # CFLAGS+= -DSTATIC_BOOTFILE=\"tftp://192.168.25.101/pxelinux.0\" # Specify a default bootfile to be used if the DHCP server does not # provide the information. If you do not specify this option, then # DHCP offers that do not contain bootfiles will be ignored. # CFLAGS+= -DDEFAULT_BOOTFILE=\"tftp://192.168.1.254/lts/pxelinux.0\" # Exit if there is an error loading the boot file # CFLAGS+= -DEXIT_ON_FILE_LOAD_ERROR # Limit the delay on packet loss/congestion to a more bearable value. See # description above. If unset, do not limit the delay between resend. CFLAGS+= -DBACKOFF_LIMIT=7 -DCONGESTED # More optional features # CFLAGS+= -DTRY_FLOPPY_FIRST=4 # CFLAGS+= -DEXIT_IF_NO_OFFER # For a serial console, which can run in parallel with FIRMWARE console # CFLAGS+= -DCONSOLE_DUAL -DCOMCONSOLE=0x3F8 -DCONSPEED=9600 # Enable tagged image, generic ELF, Multiboot ELF # or FreeBSD ELF/a.out boot image support CFLAGS+= -DTAGGED_IMAGE -DELF_IMAGE # CFLAGS+= -DAOUT_IMAGE -DIMAGE_MULTIBOOT -DIMAGE_FREEBSD # CFLAGS+= -DAOUT_IMAGE -DAOUT_LYNX_KDI # CFLAGS+= -DCOFF_IMAGE # CFLAGS+= -DRAW_IMAGE # Download files via TFTP CFLAGS+= -DDOWNLOAD_PROTO_TFTP # FSP support # CFLAGS+= -DDOWNLOAD_PROTO_FSP -DDEFAULT_PROTO_FSP # Change download protocol to NFS, default is TFTP # CFLAGS+= -DDOWNLOAD_PROTO_NFS # Change download protocol to HTTP, default is TFTP # CFLAGS+= -DDOWNLOAD_PROTO_HTTP # Change default protocol to NFS # CFLAGS+= -DDEFAULT_PROTO_NFS # Support to resolve hostnames in boot filename # CFLAGS+= -DDNS_RESOLVER # Multicast Support # CFLAGS+= -DALLMULTI -DMULTICAST_LEVEL1 -DMULTICAST_LEVEL2 -DDOWNLOAD_PROTO_TFTM # Etherboot as a PXE network protocol ROM # (Requires TFTP protocol support) CFLAGS+= -DPXE_IMAGE -DPXE_EXPORT # Etherboot stricter as a PXE network protocol ROM # CFLAGS+= -DPXE_DHCP_STRICT # Support for PXE emulation. Works only with FreeBSD to load the kernel # via pxeboot, use only with DOWNLOAD_PROTO_NFS # CFLAGS+= -DFREEBSD_PXEEMU # Include an auto-incrementing build serial number and optional build # ID string # CFLAGS+= -DBUILD_SERIAL # CFLAGS+= -DBUILD_SERIAL -DBUILD_ID=\"testing\" # Do not relocate # core/relocate.c should really be moved to an arch specific directory # but this is here for archs that don't support relocation # CFLAGS+= -DNORELOCATE # you should normally not need to change these HOST_CC= gcc CPP= gcc -E -Wp,-Wall RM= rm -f TOUCH= touch PERL= /usr/bin/perl CC= gcc AS= as LD= ld SIZE= size AR= ar RANLIB= ranlib OBJCOPY= objcopy CFLAGS+= -Os -ffreestanding CFLAGS+= -Wall -W -Wno-format CFLAGS+= $(EXTRA_CFLAGS) ASFLAGS+= $(EXTRA_ASFLAGS) LDFLAGS+= $(EXTRA_LDFLAGS) # For debugging # LDFLAGS+= -Map $@.map # Location to place generated binaries, and files BIN=bin ----------------------------------------------------------------------------- arch/i386/Confi # BIOS select don't change unless you know what you are doing #CFLAGS+= -DPCBIOS # Compile in k8/hammer support CFLAGS+= -DCONFIG_X86_64 # Options to make a version of Etherboot that will work under linuxBIOS. CFLAGS+= -DLINUXBIOS CFLAGS+= -DCONFIG_TSC_CURRTICKS CFLAGS+= -DCONSOLE_SERIAL CFLAGS+= -DCOMCONSOLE=0x3f8 CFLAGS+= -DCOMPRESERVE CFLAGS+= -DCONFIG_PCI_DIRECT CFLAGS+= -DELF_IMAGE CFLAGS+= -DCONSOLE_DIRECT_VGA # These options affect the loader that is prepended to the Etherboot image # LCONFIG+= -DBBS_BUT_NOT_PNP_COMPLIANT # LCONFIG+= -DBOOT_INT18H # Produce code that will work inside the Bochs emulator. The pnic # driver is probably the best one to try. CFLAGS+= -DCONFIG_PCI_DIRECT # Produce code that will work with OpenBSD's pxeboot #CFLAGS+= -DFLATTEN_REAL_MODE CFLAGS+= -fstrength-reduce -fomit-frame-pointer -march=i386 # Squeeze the code in as little space as possible. # gcc3 needs a different syntax to gcc2 if you want to avoid spurious warnings. GCC_VERSION = $(subst ., ,$(shell $(CC) -dumpversion)) GCC_MAJORVERSION = $(firstword $(GCC_VERSION)) ifeq ($(GCC_MAJORVERSION),2) CFLAGS+= -malign-jumps=1 -malign-loops=1 -malign-functions=1 else CFLAGS+= -falign-jumps=1 -falign-loops=1 -falign-functions=1 endif GCC_MINORVERSION = $(word 2, $(GCC_VERSION)) ifneq ($(GCC_MINORVERSION),4) CFLAGS+= -march=i386 endif LDFLAGS+= -N ifeq "$(shell uname -s)" "FreeBSD" CFLAGS+= -DIMAGE_FREEBSD -DELF_IMAGE -DAOUT_IMAGE endif # An alternate location for isolinux.bin can be set here # ISOLINUX_BIN=/path/to/isolinux.bin ----------------------------------------------------------------------------------- filo/Config #AUTOBOOT_FILE = "hda3:/boot/vmlinuz root=/dev/hda3 console=tty0 console=ttyS0,115200" AUTOBOOT_FILE = "hda2:/boot/vmlinuz initrd=/boot/initrd pci=noacpi ro root=/dev/hda2 console=tty0 console=ttyS0,115200" #AUTOBOOT_FILE = "mem@0xfff80000" #AUTOBOOT_FILE = "hde1@0" #AUTOBOOT_FILE = "uda1:/ram0_2.5_2.6.5_k8.2_mydisk7.elf" #AUTOBOOT_FILE = "hda5:/boot/vmlinuz initrd=/boot/initrd ro root=/dev/hda7 console=tty0 console=ttyS0,115200" # Time in second before booting AUTOBOOT_FILE AUTOBOOT_DELAY = 2 # Driver for hard disk, CompactFlash, and CD-ROM on IDE bus IDE_DISK = 1 # Driver for USB disk USB_DISK = 1 # Filesystems # To make filo.zelf < 32 k, You may not enable JFS, MINIX, XFS # Is anyone still using these file system? BY LYH FSYS_EXT2FS = 1 FSYS_FAT = 1 #FSYS_JFS = 1 #FSYS_MINIX = 1 FSYS_REISERFS = 1 #FSYS_XFS = 1 FSYS_ISO9660 = 1 # Support for boot disk image in bootable CD-ROM (El Torito) ELTORITO = 1 # PCI support SUPPORT_PCI = 1 # Debugging #DEBUG_ALL = 1 #DEBUG_ELFBOOT = 1 #DEBUG_ELFNOTE = 1 #DEBUG_LINUXBIOS = 1 #DEBUG_MALLOC = 1 #DEBUG_MULTIBOOT = 1 #DEBUG_SEGMENT = 1 #DEBUG_SYS_INFO = 1 #DEBUG_TIMER = 1 #DEBUG_BLOCKDEV = 1 #DEBUG_PCI = 1 #DEBUG_LINUXLOAD = 1 #DEBUG_IDE = 1 #DEBUG_USB = 1 #DEBUG_ELTORITO = 1 # i386 options # Loader for standard Linux kernel image, a.k.a. /vmlinuz LINUX_LOADER = 1 # Boot FILO from Multiboot loader (eg. GRUB) # You need to modify i386/multiboot.c to use it. change mmrange to e820entries. # By LYH #MULTIBOOT_IMAGE = 1 # Use PCI Configuration Mechanism #1 (most boards) PCI_CONFIG_1 = 1 __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

2 1

[LinuxBIOS] VIA EPIA MII6000E
by Wojciech Kromer 13 Jun '06

13 Jun '06

I've followed instuctions in EPIA-M-howto, but can't boot anything. How could I boot from cdrom now??? What is correct syntax in command line grub (filo-grub) LinuxBIOS-1.1.8.0Fallback pon cze 12 12:33:20 CEST 2006 starting... Enabling mainboard devices Enabling shadow ram vt8623 init starting Detecting Memory Number of Banks 04 Number of Rows 0d Priamry DRAM width08 No Columns 0a MA type e0 Bank 0 (*16 Mb) 10 No Physical Banks 01 Total Memory (*16 Mb) 10 CAS Supported 2 2.5 3 Cycle time at CL X (nS)50 Cycle time at CL X-0.5 (nS)60 Cycle time at CL X-1 (nS)75 Starting at CAS 3 We can do CAS 2.5 We can do CAS 2 tRP 3c tRCD 3c tRAS 28 Low Bond 06 High Bondd0 Setting DQS delay8cvt8623 done 00:06 11 23 31 06 00 30 22 00 00 00 06 00 00 00 00 10:08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30:00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 40:00 18 88 80 82 44 00 00 18 99 88 80 82 44 00 00 50:c8 de cf 88 e0 07 00 00 e0 00 10 10 10 10 00 00 60:02 ff 00 30 52 32 01 20 42 2d 43 58 00 44 00 00 70:82 48 00 01 01 08 50 00 01 00 00 00 00 00 02 02 80:0f 61 00 00 80 00 00 00 02 00 00 00 00 00 00 00 90:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0:02 c0 20 00 07 02 00 1f 04 00 00 00 2f 02 04 00 b0:00 00 00 00 80 00 00 00 a8 00 00 00 00 00 00 00 c0:01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 d0:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0:00 dd 00 00 00 00 01 00 40 00 00 00 00 00 00 00 f0:00 00 00 00 00 00 12 13 00 00 00 00 00 00 00 00 AGP Doing MTRR init. Copying LinuxBIOS to ram. Jumping to LinuxBIOS. LinuxBIOS-1.1.8.0Fallback pon cze 12 12:33:20 CEST 2006 booting... clocks_per_usec: 941 Enumerating buses... Finding PCI configuration type. PCI: Using configuration type 1 PCI_DOMAIN: 0000 enabled APIC_CLUSTER: 0 enabled PCI: pci_scan_bus for bus 0 PCI: 00:00.0 [1106/3123] enabled PCI: 00:01.0 [1106/b091] enabled PCI: 00:0a.0 [1180/0476] enabled PCI: 00:0a.1 [1180/0476] enabled In vt8235_enable 1106 3038. PCI: 00:10.0 [1106/3038] enabled In vt8235_enable 1106 3038. PCI: 00:10.1 [1106/3038] enabled In vt8235_enable 1106 3038. PCI: 00:10.2 [1106/3038] enabled In vt8235_enable 1106 3104. PCI: 00:10.3 [1106/3104] enabled In vt8235_enable 1106 3177. Initialising Devices PCI: 00:11.0 [1106/3177] enabled In vt8235_enable 1106 0571. PCI: 00:11.1 [1106/0571] enabled In vt8235_enable 1106 3059. PCI: 00:11.5 [1106/3059] enabled In vt8235_enable ffff ffff. In vt8235_enable 1106 3065. PCI: 00:12.0 [1106/3065] enabled PCI: pci_scan_bus for bus 1 PCI: 01:00.0 [1106/3122] enabled PCI: pci_scan_bus returning with max=01 PCI: pci_scan_bus for bus 2 PCI: pci_scan_bus returning with max=02 PCI: pci_scan_bus for bus 3 PCI: pci_scan_bus returning with max=03 vt1211 enabling PNP devices. PNP: 002e.0 enabled vt1211 enabling PNP devices. PNP: 002e.1 enabled vt1211 enabling PNP devices. PNP: 002e.2 enabled vt1211 enabling PNP devices. PNP: 002e.3 enabled vt1211 enabling PNP devices. PNP: 002e.b enabled PCI: pci_scan_bus returning with max=03 done Allocating resources... Reading resources... Done reading resources. Setting resources... I would set ram size to 0x40000 Kbytes PCI: 00:0a.0 In set resources PCI: 00:0a.0 10 <- [0x00febfb000 - 0x00febfbfff] mem PCI: 00:0a.0 2c <- [0x0000001870 - 0x000000286f] io PCI: 00:0a.0 34 <- [0x0000002870 - 0x000000386f] io PCI: 00:0a.0 1c <- [0x00f6bfb000 - 0x00f8bfafff] prefmem PCI: 00:0a.0 24 <- [0x00f8bfb000 - 0x00fabfafff] mem PCI: 00:0a.1 In set resources PCI: 00:0a.1 1 ==> febfc000 PCI: 00:0a.1 10 <- [0x00febfd000 - 0x00febfdfff] mem PCI: 00:0a.1 2c <- [0x0000003870 - 0x000000486f] io PCI: 00:0a.1 34 <- [0x0000004870 - 0x000000586f] io PCI: 00:0a.1 1c <- [0x00fabfb000 - 0x00fcbfafff] prefmem PCI: 00:0a.1 24 <- [0x00fcbfb000 - 0x00febfafff] mem PCI: 00:10.0 20 <- [0x0000001800 - 0x000000181f] io PCI: 00:10.1 20 <- [0x0000001820 - 0x000000183f] io PCI: 00:10.2 20 <- [0x0000001840 - 0x000000185f] io PCI: 00:10.3 10 <- [0x00febfe000 - 0x00febfe0ff] mem PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] io PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq PNP: 002e.1 60 <- [0x0000000378 - 0x000000037f] io PNP: 002e.1 70 <- [0x0000000007 - 0x0000000007] irq PNP: 002e.1 74 <- [0x0000000003 - 0x0000000003] drq PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.3 60 <- [0x00000002f8 - 0x00000002ff] io PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq PNP: 002e.b 60 <- [0x000000ec00 - 0x000000ecff] io PCI: 00:11.1 20 <- [0x0000001860 - 0x000000186f] io PCI: 00:11.5 10 <- [0x0000001000 - 0x00000010ff] io PCI: 00:12.0 10 <- [0x0000001400 - 0x00000014ff] io PCI: 00:12.0 14 <- [0x00febff000 - 0x00febff0ff] mem Done setting resources. Done allocating resources. Enabling resources... PCI: 00:00.0 cmd <- 146 PCI: 00:01.0 bridge ctrl <- 000f PCI: 00:01.0 cmd <- 147 PCI: 01:00.0 cmd <- 140 PCI: 00:0a.0 bridge ctrl <- 0503 PCI: 00:0a.0 cmd <- 143 PCI: 00:0a.1 bridge ctrl <- 0503 PCI: 00:0a.1 cmd <- 143 PCI: 00:10.0 subsystem <- 00/00 PCI: 00:10.0 cmd <- 141 PCI: 00:10.1 subsystem <- 00/00 PCI: 00:10.1 cmd <- 141 PCI: 00:10.2 subsystem <- 00/00 PCI: 00:10.2 cmd <- 141 PCI: 00:10.3 subsystem <- 00/00 PCI: 00:10.3 cmd <- 142 PCI: 00:11.0 cmd <- 147 PNP: 002e.0 - enabling PNP: 002e.1 - enabling PNP: 002e.2 - enabling PNP: 002e.3 - enabling PNP: 002e.b - enabling PCI: 00:11.1 cmd <- 147 PCI: 00:11.5 subsystem <- 00/00 PCI: 00:11.5 cmd <- 141 PCI: 00:12.0 cmd <- 1c3 done. Initializing devices... Root Device init PCI: 00:10.0 init PCI: 00:10.1 init PCI: 00:10.2 init PCI: 00:10.3 init PCI: 00:11.0 init vt8235 init RTC Init Invalid CMOS LB checksum pci_routing_fixup: dev is 000111a0 setting firewire setting usb Assigning IRQ 5 to 0:10.0 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 Assigning IRQ 9 to 0:10.1 Readback = 9 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 Assigning IRQ 9 to 0:10.2 Readback = 9 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 Assigning IRQ 5 to 0:10.3 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 setting vt8235 Assigning IRQ 5 to 0:11.1 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 Assigning IRQ 9 to 0:11.5 Readback = 9 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 setting ethernet Assigning IRQ 5 to 0:12.0 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 setting vga Assigning IRQ 5 to 1:0.0 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 setting pci slot setting cardbus slot Assigning IRQ 5 to 0:a.0 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 Assigning IRQ 5 to 0:a.1 Readback = 5 pci_level_irq: lower order bits are wrong: want 0x0, got 0x20 ^^^^ why? any missconfiguration? setting riser slot PNP: 002e.0 init PNP: 002e.1 init PNP: 002e.2 init PNP: 002e.3 init PNP: 002e.b init PCI: 00:11.1 init Enabling VIA IDE. ide_init: enabling compatibility IDE addresses enables in reg 0x42 0x0 enables in reg 0x42 read back as 0x0 enables in reg 0x40 0x13 enables in reg 0x40 read back as 0x13 enables in reg 0x9 0x8a enables in reg 0x9 read back as 0x8a command in reg 0x4 0x7 command in reg 0x4 reads back as 0x7 ^^^^ is it wrong ???? PCI: 00:11.5 init PCI: 00:12.0 init Configuring VIA Rhine LAN PCI: 00:0a.0 init rl5c476 init CF Base = febfc000 PCI: 00:0a.1 init rl5c476 init CF Base = febfc000 CF Config = 0 APIC_CLUSTER: 0 init Initializing CPU #0 CPU: vendor Centaur device 673 Enabling cache Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB Setting fixed MTRRs(24-88) Type: WB DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 128MB, type WB Setting variable MTRR 1, base: 128MB, range: 64MB, type WB Setting variable MTRR 2, base: 192MB, range: 32MB, type WB DONE variable MTRRs Clear out the extra MTRR's MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled Disabling local apic...done. CPU #0 Initialized PCI: 00:00.0 init VT8623 random fixup ... Frame buffer at d0000000 PCI: 00:01.0 init VT8623 AGP random fixup ... PCI: 01:00.0 init VGA random fixup ... INSTALL REAL-MODE IDT DO THE VGA BIOS found VGA: vid=1106, did=3122 rom base, size: fffc0000 BAD SIGNATURE 0xb4 0x0 ^^^^^ why? I grab vide.bios.rom just as in howto, and changed everything... biosint: INT# 0x10 biosint: eax 0x4f14 ebx 0x18003 ecx 0x1 edx 0x0 biosint: ebp 0x17fa8 esp 0xffa edi 0x0 esi 0xffff7063 biosint: ip 0xbb85 cs 0x0 flags 0x46 BIOSINT: Unsupport int #0x10 Devices initialized Copying IRQ routing tables to 0xf0000...done. Verifing copy of IRQ routing tables at 0xf0000...done Checking IRQ routing table consistency... check_pirq_routing_table() - irq_routing_table located at: 0x000f0000 done ACPI: Writing ACPI tables at f0400... ACPI: * FACS ACPI: * DSDT @ 000f049e Length 3f0 ACPI: * FADT ACPI: added table 1/5 Length now 40 ACPI: done. Moving GDT to 0x500...ok Wrote linuxbios table at: 00000530 - 00000b70 checksum 3245 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 rom_stream: 0xfffd0000 - 0xfffeffff Found ELF candiate at offset 0 New segment addr 0x100000 size 0x3ca40 offset 0xc0 filesize 0x12c48 (cleaned up) New segment addr 0x100000 size 0x3ca40 offset 0xc0 filesize 0x12c48New segment addr 0x13ca40 size 0x48 offset 0x12d20 filesize 0x48 (cleaned up) New segment addr 0x13ca40 size 0x48 offset 0x12d20 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x0000000000100000 memsz: 0x000000000003ca40 filesz: 0x00Clearing Segment: addr: 0x0000000000112c48 memsz: 0x0000000000029df8 Loading Segment: addr: 0x000000000013ca40 memsz: 0x0000000000000048 filesz: 0x00Jumping to boot code at 0x10e408 FILO version 0.5 (krom(a)krom.bkir.dgt) pon cze 12 10:55:25 CEST 2006 menu: hda3:/boot/filo/menu.lst ^^^ this is my mistake, should be hde1:/boot/filo/menu.lst for CF but i want to boot anything now.... hda: ATAPI: HL-DT-ST DVDRAM GSA-4167B Waiting for drive to detect the medium... 50MB medium detected El-Torito entries other than Initial/Default is not supported Press any key to continue. ......

1 0

[LinuxBIOS] EPIA-V8000
by Scott 12 Jun '06

12 Jun '06

Hi All, Is anyone aware of a rom image of V2 that is available for the Via EPIA-V8000 or an updated Tutorial on setting up V2 on this board? Thanks.

2 1

[LinuxBIOS] bochs and qemu
by Tyler Pohl 12 Jun '06

12 Jun '06

Where could i download a linuxbios.bin file that runs with qemu? Maybe even find some documentation on how to compie the linuxbios to run under qemu. Thanks Again :) Tyler

4 3

[LinuxBIOS] INIT detected from ---- {APICID = 00 NODEID = 00 COREID = 00}
by steve yannalfo 12 Jun '06

12 Jun '06

SAME Thanks for you help though... still working on this. The Docs say FILO can boot a regular kernel, bzImage, memtest, elf images etc... So I don't know why it was complaining about it not being an ELF. I just thought that was the default. Still same err though. ---------------------------------------------- boot: hda1:/boot/memtest86/memtest.elf console=tty0 console=ttyS0,115200n8 malloc_diag: alloc: 456 bytes (5 blocks), free: 15920 bytes (1 blocks) malloc_diag: alloc: 472 bytes (6 blocks), free: 15904 bytes (1 blocks) file_open: dev=hda1, path=/boot/memtest86/memtest.elf find_ide_controller: found PCI IDE controller 10de:0053 prog_if=0x8a find_ide_controller: primary channel: compatibility mode find_ide_controller: cmd_base=0x1f0 ctrl_base=0x3f4 ide_software_reset: Waiting for ide0 to become ready for reset... ok init_drive: Testing for hda init_drive: Probing for hda init_drive: LBA mode, sectors=1019088 init_drive: Init device params... ok hda: LBA 521MB: SILICONSYSTEMS INC 512MB init_drive: Testing for hdb init_drive: Testing for hdb devopen: Partition 1 start 59 length 1018989 Mounted ext2fs malloc_diag: alloc: 456 bytes (5 blocks), free: 15920 bytes (1 blocks) malloc_diag: alloc: 528 bytes (6 blocks), free: 15848 bytes (1 blocks) Loading image... load_segments: segment 0 addr:0x10000 file:0x155f4 mem:0x155f4 loading... clearing... ok load_segments: Loaded 87540 bytes in 568ms (154KB/s) malloc_diag: alloc: 792 bytes (7 blocks), free: 15584 bytes (1 blocks) elf_load: current time: 36403 elf_load: entry point is 0x10000 Jumping to entry point... INIT detected from ---- {APICID = 00 NODEID = 00 COREID = 00} --- Issuing SOFT_RESET... ------------------------------------------ Thank you steve __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

1 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot June 2006