coreboot October 2006

coreboot@coreboot.org

53 participants
208 discussions

Re: [LinuxBIOS] Tyan s2892 the OLPC way
by Myles Watson 30 Oct '06

30 Oct '06

Here is the tarball, resolve.S (needed for uclibc), and a patch from the OLPC buildrom. I haven't made it totally automated. I just have a symbolic link to the payload generated in the deploy directory from my other LinuxBIOS directory. resolve.S needs to be copied into buildrom/work/uclibc/uClibc-0.9.28/ldso/ldso/x86_64/resolve.S Otherwise uclibc will not build. Myles > -----Original Message----- > From: yhlu [mailto:yinghailu@gmail.com] > Sent: Monday, October 30, 2006 9:48 AM > To: myles(a)mouselemur.cs.byu.edu > Subject: Re: [LinuxBIOS] Tyan s2892 the OLPC way > > please. > > On 10/30/06, Myles Watson <myles(a)pel.cs.byu.edu> wrote: > > I can send it to you if you want, but there are very few modifications > from > > the original. > > > > I built it all in a 64-bit environment once I had it working. > > > > I got rid of kexec-boot-loader and included a statically linked kexec. > It > > saved some space in the ROM for me. > > > > I guess I don't know enough about .elf.lzma and what's going on > underneath. > > I just let buildrom take care of it for me. > > > > Myles > > > > > -----Original Message----- > > > From: yhlu [mailto:yinghailu@gmail.com] > > > Sent: Sunday, October 29, 2006 11:08 PM > > > To: ron minnich; myles(a)mouselemur.cs.byu.edu > > > Cc: Lu, Yinghai > > > Subject: Re: [LinuxBIOS] Tyan s2892 the OLPC way > > > > > > Can you send me your buildrom tar ball to me? > > > > > > Also for .elf.lzma, do you need one new mkelfImage to build elf with > > > uncompress kernel and initrd? > > > > > > Also I hope I can build it under 64bit environment. > > > > > > Thanks > > > > > > Yinghai Lu > > > > > >

1 0

[LinuxBIOS] Chipset support
by Jaganmohan, Gopinath (Cognizant) 30 Oct '06

30 Oct '06

Hi, I have Asus motherboard p4ge-mx. The details are here North bridge :- Intel 845 GE South bridge:- Intel ICh4(FW828201DB) Please let me know whether I can use linuxbios in my system. Looking forward!!! Thanks & Regards, Gopinath This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender by reply e-mail and destroy all copies of the original message. Any unauthorized review, use, disclosure, dissemination, forwarding, printing or copying of this email or any action taken in reliance on this e-mail is strictly prohibited and may be unlawful. Visit us at http://www.cognizant.com

3 5

Re: [LinuxBIOS] Tyan s2892 the OLPC way
by Lu, Yinghai 30 Oct '06

30 Oct '06

Just comment out the jmp to normal section, should be more easier. YH -----Original Message----- From: linuxbios-bounces(a)linuxbios.org [mailto:linuxbios-bounces@linuxbios.org] On Behalf Of Myles Watson Sent: Wednesday, October 18, 2006 12:23 PM To: linuxbios(a)linuxbios.org Subject: Re: [LinuxBIOS] Tyan s2892 the OLPC way Do we need a new variable FALLBACK_ONLY ? I put together the attached patch to try to modify it nicely, but I'm not sure it works as I intended. I wanted to only try to jump to normal when there is a normal, but the variables are all FALLBACK-oriented. Myles > Or modify you cache_as_ram_auto.c failover.c, force it to jump to > fallback only for safe. > > YH > > That was it. When should I have to do that? > > Myles > > > -----Original Message----- > > From: Lu, Yinghai [mailto:yinghai.lu@amd.com] > > Sent: Wednesday, October 18, 2006 12:16 PM > > To: myles(a)mouselemur.cs.byu.edu > > Subject: RE: [LinuxBIOS] Tyan s2892 the OLPC way > > > > Clear your CMOS by using the hw jump.

3 4

[LinuxBIOS] MSI ms9185 linuxbios support
by bxshi＠msik.com.cn 30 Oct '06

30 Oct '06

Index: src/southbridge/broadcom/bcm5785/bcm5785_sata.c =================================================================== --- src/southbridge/broadcom/bcm5785/bcm5785_sata.c (revision 2475) +++ src/southbridge/broadcom/bcm5785/bcm5785_sata.c (working copy) @@ -21,6 +21,8 @@ uint8_t *base; uint8_t *mmio; struct resource *res; + unsigned int mmio_base; + volatile unsigned int *mmio_reg; int i; if(!(dev->path.u.pci.devfn & 7)) { // only set it in Func0 @@ -30,6 +32,21 @@ res = find_resource(dev, 0x24); base = res->base; + + mmio_base = base; + mmio_base &= 0xfffffffc; + mmio_reg = (unsigned int *)( mmio_base + 0x10f0 ); + * mmio_reg = 0x40000001; + mmio_reg = ( unsigned int *)( mmio_base + 0x8c ); + * mmio_reg = 0x00ff2007; + mdelay( 10 ); + * mmio_reg = 0x78592009; + mdelay( 10 ); + * mmio_reg = 0x00082004; + mdelay( 10 ); + * mmio_reg = 0x00002004; + mdelay( 10 ); + //init PHY printk_debug("init PHY...\n"); Index: src/devices/emulator/biosemu.c =================================================================== --- src/devices/emulator/biosemu.c (revision 2475) +++ src/devices/emulator/biosemu.c (working copy) @@ -121,6 +121,7 @@ case 0x42: case 0x6D: if (getIntVect(num) == 0x0000) { + ret = 1 ; /*to make vga work*/ printk_debug("un-inited int vector\n"); } if (getIntVect(num) == 0xFF065) { Index: src/mainboard/msi/ms9185/Config.lb =================================================================== --- src/mainboard/msi/ms9185/Config.lb (revision 0) +++ src/mainboard/msi/ms9185/Config.lb (revision 0) @@ -0,0 +1,275 @@ +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The linuxBIOS bootloader. +## +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +#dir /drivers/si/3114 + +#needed by irq_tables and mptable and acpi_tables +object get_bus_conf.o + +if HAVE_MP_TABLE + object mptable.o +end + +if HAVE_PIRQ_TABLE + object irq_tables.o +end + +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + # compile cache_as_ram.c to auto.o + makerule ./cache_as_ram_auto.o + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" + end + + else + #compile cache_as_ram.c to auto.inc + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end + + end +end +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## + +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/entry16.inc + ldscript /cpu/x86/16bit/entry16.lds +end + +mainboardinit cpu/x86/32bit/entry32.inc +if USE_DCACHE_RAM + if CONFIG_USE_INIT + ldscript /cpu/x86/32bit/entry32.lds + end + + if CONFIG_USE_INIT + ldscript /cpu/amd/car/cache_as_ram.lds + end +end + +## +## Build our reset vector (This is where linuxBIOS is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +if USE_DCACHE_RAM + ## + ## Setup Cache-As-Ram + ## + mainboardinit cpu/amd/car/cache_as_ram.inc +end + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + if USE_DCACHE_RAM + ldscript /arch/i386/lib/failover.lds + end +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + initobject cache_as_ram_auto.o + else + mainboardinit ./cache_as_ram_auto.inc + end + +end + +## +## Include the secondary Configuration files +## +if CONFIG_CHIP_NAME + config chip.h +end + +# sample config for amd/serengeti_cheetah +chip northbridge/amd/amdk8/root_complex + device apic_cluster 0 on + chip cpu/amd/socket_F + device apic 0 on end + end + end + device pci_domain 0 on + chip northbridge/amd/amdk8 + device pci 18.0 on end + device pci 18.0 on end + device pci 18.0 on # northbridge + # devices on link 0 + chip southbridge/broadcom/bcm5780 # HT2000 + device pci 0.0 on end # PXB 1 0x0130 + device pci 1.0 on # PXB 2 0x0130 + device pci 4.0 on end # GB E 0x1668 vid = 0x14e4 + device pci 4.1 on end # GB E 0x1669 vid = 0x14e4 + end + device pci 2.0 on end # PCI E 1 #0x0132 + device pci 3.0 on end # PCI E 2 + device pci 4.0 on end # PCI E 3 + device pci 5.0 on end # PCI E 4 + end + chip southbridge/broadcom/bcm5785 # HT1000 + device pci 0.0 on # HT PXB 0x0036 + device pci d.0 on end # PPBX 0x0104 + device pci e.0 on end # SATA 0x024a + device pci e.1 on end # SATA 0x024a bx_a001 + device pci e.2 on end # SATA 0x024a bx_a001 + device pci e.3 on end # SATA 0x024a bx_a001 + end + device pci 1.0 on # Legacy pci main 0x0205 + end + device pci 1.1 on end # IDE 0x0214 + device pci 1.2 on # LPC 0x0234 + chip superio/NSC/pc87417 + device pnp 2e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 off # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + end + device pnp 2e.2 off # Com 2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.3 on # Com 1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.4 off end # SWC + device pnp 2e.5 off end # Mouse + device pnp 2e.6 on # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + end + device pnp 2e.7 off end # GPIO + device pnp 2e.f off end # XBUS + device pnp 2e.10 on #RTC + io 0x60 = 0x70 + io 0x62 = 0x72 + end + end + end + device pci 1.3 on end # WDTimer 0x0238 + device pci 1.4 on end # XIOAPIC0 0x0235 + device pci 1.5 on end # XIOAPIC1 + device pci 1.6 on end # XIOAPIC2 + device pci 2.0 on end # USB 0x0223 + device pci 2.1 on end # USB + device pci 2.2 on end # USB + #when HT_CHAIN_END_UNITID_BASE (0,1) < HT_CHAIN_UNITID_BASE (6,,,,), + chip drivers/pci/onboard + device pci 3.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed, fake one to get the rom_address + # if HT_CHAIN_END_UNITID_BASE=0, it is 4, if HT_CHAIN_END_UNITID_BASE=1, it is 3 + register "rom_address" = "0xfff80000" + end + #bx_a013+ start + #chip drivers/pci/onboard #SATA2 + # device pci 5.0 on end + # device pci 5.1 on end + # device pci 5.2 on end + # device pci 5.3 on end + #end + #bx_a013+ end + + end + #when HT_CHAIN_END_UNITID_BASE > HT_CHAIN_UNITID_BASE (6, ,,,,) +# chip drivers/pci/onboard +# device pci 0.0 on end # fake, will be disabled +# end +# chip drivers/pci/onboard +# device pci 4.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed +# register "rom_address" = "0xfff80000" +# end + + end # device pci 18.0 + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end # amdk8 + end #pci_domain +# chip drivers/generic/debug +# device pnp 0.0 off end # chip name +# device pnp 0.1 on end # pci_regs_all +# device pnp 0.2 off end # mem +# device pnp 0.3 off end # cpuid +# device pnp 0.4 off end # smbus_regs_all +# device pnp 0.5 off end # dual core msr +# device pnp 0.6 off end # cache size +# device pnp 0.7 off end # tsc +# end + +end + + Property changes on: src/mainboard/msi/ms9185/Config.lb ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/mptable.c =================================================================== --- src/mainboard/msi/ms9185/mptable.c (revision 0) +++ src/mainboard/msi/ms9185/mptable.c (revision 0) @@ -0,0 +1,179 @@ +#include <console/console.h> +#include <arch/smp/mpspec.h> +#include <arch/io.h> +#include <device/pci.h> +#include <string.h> +#include <stdint.h> +#if CONFIG_LOGICAL_CPUS==1 +#include <cpu/amd/dualcore.h> +#endif + +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + +extern void get_bus_conf(void); + +void *smp_write_config_table(void *v) +{ + static const char sig[4] = "PCMP"; + static const char oem[3] = "MSI"; + static const char productid[6] = "MS9185 "; + struct mp_config_table *mc; + + unsigned char bus_num; + int i; + struct mb_sysconf_t *m; + + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); + + memcpy(mc->mpc_signature, sig, sizeof(sig)); + mc->mpc_length = sizeof(*mc); /* initially just the header */ + mc->mpc_spec = 0x04; + mc->mpc_checksum = 0; /* not yet computed */ + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + mc->mpc_oemptr = 0; + mc->mpc_oemsize = 0; + mc->mpc_entry_count = 0; /* No entries yet... */ + mc->mpc_lapic = LAPIC_ADDR; + mc->mpe_length = 0; + mc->mpe_checksum = 0; + mc->reserved = 0; + + smp_write_processors(mc); + + get_bus_conf(); + m = sysconf.mb; + +/*Bus: Bus ID Type*/ + /* define bus and isa numbers */ + for(bus_num = 0; bus_num < m->bus_isa; bus_num++) { + smp_write_bus(mc, bus_num, "PCI "); + } + smp_write_bus(mc, m->bus_isa, "ISA "); + +/*I/O APICs: APIC ID Version State Address*/ + { + device_t dev = 0; + int i; + struct resource *res; + for(i=0; i<3; i++) { + dev = dev_find_device(0x1166, 0x0235, dev); + if (dev) { + res = find_resource(dev, PCI_BASE_ADDRESS_0); + if (res) { + smp_write_ioapic(mc, m->apicid_bcm5785[i], 0x11, res->base); + } + } + } + + } + +/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x1, m->apicid_bcm5785[0], 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x3, m->apicid_bcm5785[0], 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x4, m->apicid_bcm5785[0], 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x5, m->apicid_bcm5785[0], 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x6, m->apicid_bcm5785[0], 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x7, m->apicid_bcm5785[0], 0x7); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x8, m->apicid_bcm5785[0], 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x9, m->apicid_bcm5785[0], 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xc, m->apicid_bcm5785[0], 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xd, m->apicid_bcm5785[0], 0xd); + +//IDE + outb(0x02, 0xc00); outb(0x0e, 0xc01); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_bcm5785_0, ((1+sysconf.sbdn)<<2)|1, m->apicid_bcm5785[0], 0xe); // IDE + +//SATA + outb(0x07, 0xc00); outb(0x0f, 0xc01); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1, (0x0e<<2)|0, m->apicid_bcm5785[0], 0xf); + +//USB + outb(0x01, 0xc00); outb(0x0a, 0xc01); + for(i=0;i<3;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, ((2+sysconf.sbdn)<<2)|i, m->apicid_bcm5785[0], 0xa); // + } + + + + /* enable int */ + /* why here? must get the BAR and PCI command bit 1 set before enable it ....*/ + { + device_t dev; + dev = dev_find_device(0x1166, 0x0205, 0); + if(dev) { + uint32_t dword; + dword = pci_read_config32(dev, 0x6c); + dword |= (1<<4); // enable interrupts + pci_write_config32(dev, 0x6c, dword); + } + } + +//First pci-x slot (on bcm5785) under bus_bcm5785_1:d.0 + // AIC 8130 Galileo Technology... + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1_1, (6<<2)|i, m->apicid_bcm5785[1], 2 + (1+i)%4); // + } + + +//pci slot (on bcm5785) + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (5<<2)|i, m->apicid_bcm5785[1], 8+i%4); // + } + + +//onboard ati + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (4<<2)|0, m->apicid_bcm5785[1], 0x1); + +//PCI-X on bcm5780 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[1], (4<<2)|i, m->apicid_bcm5785[1], 2 + (0+i)%4); // + } + +//onboard Broadcom + for(i=0;i<2;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[2], (4<<2)|i, m->apicid_bcm5785[1], 0xa + (0+i)%4); // + } + + +// First PCI-E x8 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[5], (0<<2)|i, m->apicid_bcm5785[1], 0xe); // + } + + +// Second PCI-E x8 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[3], (0<<2)|i, m->apicid_bcm5785[1], 0xc); // + } + +// Third PCI-E x1 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[4], (0<<2)|i, m->apicid_bcm5785[1], 0xd); // + } + +/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x1); + /* There is no extension information... */ + + /* Compute the checksums */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + printk_debug("Wrote the mp table end at: %p - %p\n", + mc, smp_next_mpe_entry(mc)); + return smp_next_mpe_entry(mc); +} + +unsigned long write_smp_table(unsigned long addr) +{ + void *v; + v = smp_write_floating_table(addr); + return (unsigned long)smp_write_config_table(v); +} Property changes on: src/mainboard/msi/ms9185/mptable.c ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/irq_tables.c =================================================================== --- src/mainboard/msi/ms9185/irq_tables.c (revision 0) +++ src/mainboard/msi/ms9185/irq_tables.c (revision 0) @@ -0,0 +1,102 @@ +/* This file was generated by getpir.c, do not modify! + (but if you do, please run checkpir on it to verify) + Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up + + Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM +*/ +#include <console/console.h> +#include <device/pci.h> +#include <string.h> +#include <stdint.h> +#include <arch/pirq_routing.h> +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + + +static void write_pirq_info(struct irq_info *pirq_info, uint8_t bus, uint8_t devfn, uint8_t link0, uint16_t bitmap0, + uint8_t link1, uint16_t bitmap1, uint8_t link2, uint16_t bitmap2,uint8_t link3, uint16_t bitmap3, + uint8_t slot, uint8_t rfu) +{ + pirq_info->bus = bus; + pirq_info->devfn = devfn; + + pirq_info->irq[0].link = link0; + pirq_info->irq[0].bitmap = bitmap0; + pirq_info->irq[1].link = link1; + pirq_info->irq[1].bitmap = bitmap1; + pirq_info->irq[2].link = link2; + pirq_info->irq[2].bitmap = bitmap2; + pirq_info->irq[3].link = link3; + pirq_info->irq[3].bitmap = bitmap3; + + pirq_info->slot = slot; + pirq_info->rfu = rfu; +} + +extern void get_bus_conf(void); + +unsigned long write_pirq_routing_table(unsigned long addr) +{ + + struct irq_routing_table *pirq; + struct irq_info *pirq_info; + unsigned slot_num; + uint8_t *v; + + uint8_t sum=0; + int i; + + struct mb_sysconf_t *m; + + get_bus_conf(); + + m = sysconf.mb; + + /* Align the table to be 16 byte aligned. */ + addr += 15; + addr &= ~15; + + /* This table must be betweeen 0xf0000 & 0x100000 */ + printk_info("Writing IRQ routing tables to 0x%x...", addr); + + pirq = (void *)(addr); + v = (uint8_t *)(addr); + + pirq->signature = PIRQ_SIGNATURE; + pirq->version = PIRQ_VERSION; + + pirq->rtr_bus = m->bus_bcm5785_0; + pirq->rtr_devfn = (sysconf.sbdn<<3)|0; + + pirq->exclusive_irqs = 0; + + pirq->rtr_vendor = 0x1166; + pirq->rtr_device = 0x0036; + + pirq->miniport_data = 0; + + memset(pirq->rfu, 0, sizeof(pirq->rfu)); + + pirq_info = (void *) ( &pirq->checksum + 1); + slot_num = 0; +//pci bridge + write_pirq_info(pirq_info, m->bus_bcm5785_0, (sysconf.sbdn<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0); + pirq_info++; slot_num++; + + pirq->size = 32 + 16 * slot_num; + + for (i = 0; i < pirq->size; i++) + sum += v[i]; + + sum = pirq->checksum - sum; + + if (sum != pirq->checksum) { + pirq->checksum = sum; + } + + printk_info("done.\n"); + + return (unsigned long) pirq_info; + +} Property changes on: src/mainboard/msi/ms9185/irq_tables.c ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/resourcemap.c =================================================================== --- src/mainboard/msi/ms9185/resourcemap.c (revision 0) +++ src/mainboard/msi/ms9185/resourcemap.c (revision 0) @@ -0,0 +1,265 @@ +/* + * ms9185 needs a different resource map + * + */ + +static void setup_ms9185_resource_map(void) +{ + static const unsigned int register_values[] = { + /* Careful set limit registers before base registers which contain the enables */ + /* DRAM Limit i Registers + * F1:0x44 i = 0 + * F1:0x4C i = 1 + * F1:0x54 i = 2 + * F1:0x5C i = 3 + * F1:0x64 i = 4 + * F1:0x6C i = 5 + * F1:0x74 i = 6 + * F1:0x7C i = 7 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 7: 3] Reserved + * [10: 8] Interleave select + * specifies the values of A[14:12] to use with interleave enable. + * [15:11] Reserved + * [31:16] DRAM Limit Address i Bits 39-24 + * This field defines the upper address bits of a 40 bit address + * that define the end of the DRAM region. + */ + PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001, + PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002, + PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003, + PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004, + PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005, + PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006, + PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007, + /* DRAM Base i Registers + * F1:0x40 i = 0 + * F1:0x48 i = 1 + * F1:0x50 i = 2 + * F1:0x58 i = 3 + * F1:0x60 i = 4 + * F1:0x68 i = 5 + * F1:0x70 i = 6 + * F1:0x78 i = 7 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 7: 2] Reserved + * [10: 8] Interleave Enable + * 000 = No interleave + * 001 = Interleave on A[12] (2 nodes) + * 010 = reserved + * 011 = Interleave on A[12] and A[14] (4 nodes) + * 100 = reserved + * 101 = reserved + * 110 = reserved + * 111 = Interleve on A[12] and A[13] and A[14] (8 nodes) + * [15:11] Reserved + * [13:16] DRAM Base Address i Bits 39-24 + * This field defines the upper address bits of a 40-bit address + * that define the start of the DRAM region. + */ + PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000, + + /* Memory-Mapped I/O Limit i Registers + * F1:0x84 i = 0 + * F1:0x8C i = 1 + * F1:0x94 i = 2 + * F1:0x9C i = 3 + * F1:0xA4 i = 4 + * F1:0xAC i = 5 + * F1:0xB4 i = 6 + * F1:0xBC i = 7 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 3: 3] Reserved + * [ 5: 4] Destination Link ID + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 = Reserved + * [ 6: 6] Reserved + * [ 7: 7] Non-Posted + * 0 = CPU writes may be posted + * 1 = CPU writes must be non-posted + * [31: 8] Memory-Mapped I/O Limit Address i (39-16) + * This field defines the upp adddress bits of a 40-bit address that + * defines the end of a memory-mapped I/O region n + */ + PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff20, + + /* Memory-Mapped I/O Base i Registers + * F1:0x80 i = 0 + * F1:0x88 i = 1 + * F1:0x90 i = 2 + * F1:0x98 i = 3 + * F1:0xA0 i = 4 + * F1:0xA8 i = 5 + * F1:0xB0 i = 6 + * F1:0xB8 i = 7 + * [ 0: 0] Read Enable + * 0 = Reads disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes disabled + * 1 = Writes Enabled + * [ 2: 2] Cpu Disable + * 0 = Cpu can use this I/O range + * 1 = Cpu requests do not use this I/O range + * [ 3: 3] Lock + * 0 = base/limit registers i are read/write + * 1 = base/limit registers i are read-only + * [ 7: 4] Reserved + * [31: 8] Memory-Mapped I/O Base Address i (39-16) + * This field defines the upper address bits of a 40bit address + * that defines the start of memory-mapped I/O region i + */ + PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003, + + /* PCI I/O Limit i Registers + * F1:0xC4 i = 0 + * F1:0xCC i = 1 + * F1:0xD4 i = 2 + * F1:0xDC i = 3 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 3: 3] Reserved + * [ 5: 4] Destination Link ID + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 = reserved + * [11: 6] Reserved + * [24:12] PCI I/O Limit Address i + * This field defines the end of PCI I/O region n + * [31:25] Reserved + */ + PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff020, + PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000, + + /* PCI I/O Base i Registers + * F1:0xC0 i = 0 + * F1:0xC8 i = 1 + * F1:0xD0 i = 2 + * F1:0xD8 i = 3 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 3: 2] Reserved + * [ 4: 4] VGA Enable + * 0 = VGA matches Disabled + * 1 = matches all address < 64K and where A[9:0] is in the + * range 3B0-3BB or 3C0-3DF independen of the base & limit registers + * [ 5: 5] ISA Enable + * 0 = ISA matches Disabled + * 1 = Blocks address < 64K and in the last 768 bytes of eack 1K block + * from matching agains this base/limit pair + * [11: 6] Reserved + * [24:12] PCI I/O Base i + * This field defines the start of PCI I/O region n + * [31:25] Reserved + */ + PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000003, + PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000, + + /* Config Base and Limit i Registers + * F1:0xE0 i = 0 + * F1:0xE4 i = 1 + * F1:0xE8 i = 2 + * F1:0xEC i = 3 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 2: 2] Device Number Compare Enable + * 0 = The ranges are based on bus number + * 1 = The ranges are ranges of devices on bus 0 + * [ 3: 3] Reserved + * [ 6: 4] Destination Node + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 7: 7] Reserved + * [ 9: 8] Destination Link + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 - Reserved + * [15:10] Reserved + * [23:16] Bus Number Base i + * This field defines the lowest bus number in configuration region i + * [31:24] Bus Number Limit i + * This field defines the highest bus number in configuration regin i + */ + PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0xff000203, + PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000, + }; + + int max; + max = sizeof(register_values)/sizeof(register_values[0]); + setup_resource_map(register_values, max); +} + Property changes on: src/mainboard/msi/ms9185/resourcemap.c ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/Options.lb =================================================================== --- src/mainboard/msi/ms9185/Options.lb (revision 0) +++ src/mainboard/msi/ms9185/Options.lb (revision 0) @@ -0,0 +1,308 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses HAVE_ACPI_TABLES +uses ACPI_SSDTX_NUM +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +uses HW_MEM_HOLE_SIZEK +uses HW_MEM_HOLE_SIZE_AUTO_INC +uses K8_HT_FREQ_1G_SUPPORT + +uses HT_CHAIN_UNITID_BASE +uses HT_CHAIN_END_UNITID_BASE +uses SB_HT_CHAIN_ON_BUS0 +uses SB_HT_CHAIN_UNITID_OFFSET_ONLY + +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_USE_INIT + +uses SERIAL_CPU_INIT + +uses ENABLE_APIC_EXT_ID +uses APIC_ID_OFFSET +uses LIFT_BSP_APIC_ID + +uses CONFIG_PCI_64BIT_PREF_MEM + +uses CONFIG_LB_MEM_TOPK + + +### +### Build options +### + +## +## ROM_SIZE is the size of boot ROM that this board will use. +## +default ROM_SIZE=524288 + +## +## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use +## +#default FALLBACK_SIZE=131072 +#256K +default FALLBACK_SIZE=0x40000 + +#more 1M for pgtbl +default CONFIG_LB_MEM_TOPK=2048 + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=11 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## ACPI tables will be included +#default HAVE_ACPI_TABLES=1 +## extra SSDT num +#default ACPI_SSDTX_NUM=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=4 +default CONFIG_MAX_PHYSICAL_CPUS=2 +default CONFIG_LOGICAL_CPUS=1 + +default SERIAL_CPU_INIT=0 + +default ENABLE_APIC_EXT_ID=0 +default APIC_ID_OFFSET=0x8 +default LIFT_BSP_APIC_ID=1 + +#CHIP_NAME ? +default CONFIG_CHIP_NAME=1 + +#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. +#2G +#default HW_MEM_HOLE_SIZEK=0x200000 +#1G +default HW_MEM_HOLE_SIZEK=0x100000 +#512M +#default HW_MEM_HOLE_SIZEK=0x80000 + +#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy +#default HW_MEM_HOLE_SIZE_AUTO_INC=1 + +#Opteron K8 1G HT Support +default K8_HT_FREQ_1G_SUPPORT=1 + +#VGA Console +default CONFIG_CONSOLE_VGA=1 +default CONFIG_PCI_ROM_RUN=1 + +#HT Unit ID offset, default is 1, the typical one +default HT_CHAIN_UNITID_BASE=0x06 + +#real SB Unit ID, default is 0x20, mean dont touch it at last +default HT_CHAIN_END_UNITID_BASE=0x01 + +#make the SB HT chain on bus 0, default is not (0) +default SB_HT_CHAIN_ON_BUS0=2 + +#only offset for SB chain?, default is yes(1) +#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 + +#allow capable device use that above 4G +#default CONFIG_PCI_64BIT_PREF_MEM=1 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xcc000 +default DCACHE_RAM_SIZE=0x04000 +default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 +default CONFIG_USE_INIT=0 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="MS9185" +default MAINBOARD_VENDOR="MSI" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022 +default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 32K heap +## +default HEAP_SIZE=0x8000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00100000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_STREAM = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end Property changes on: src/mainboard/msi/ms9185/Options.lb ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/mb_sysconf.h =================================================================== --- src/mainboard/msi/ms9185/mb_sysconf.h (revision 0) +++ src/mainboard/msi/ms9185/mb_sysconf.h (revision 0) @@ -0,0 +1,18 @@ +#ifndef MB_SYSCONF_H + +#define MB_SYSCONF_H + +struct mb_sysconf_t { + unsigned char bus_isa; + unsigned char bus_bcm5780[7]; + unsigned char bus_bcm5785_0; + unsigned char bus_bcm5785_1; + unsigned char bus_bcm5785_1_1; + unsigned apicid_bcm5785[3]; + + unsigned sbdn2; + +}; + +#endif + Property changes on: src/mainboard/msi/ms9185/mb_sysconf.h ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/chip.h =================================================================== --- src/mainboard/msi/ms9185/chip.h (revision 0) +++ src/mainboard/msi/ms9185/chip.h (revision 0) @@ -0,0 +1,5 @@ +extern struct chip_operations mainboard_msi_ms9185_ops; +struct mainboard_msi_ms9185_config { +// int fixup_scsi; +// int fixup_vga; +}; Property changes on: src/mainboard/msi/ms9185/chip.h ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/cmos.layout =================================================================== --- src/mainboard/msi/ms9185/cmos.layout (revision 0) +++ src/mainboard/msi/ms9185/cmos.layout (revision 0) @@ -0,0 +1,98 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +395 1 e 1 hw_scrubber +396 1 e 1 interleave_chip_selects +397 2 e 8 max_mem_clock +399 1 e 2 dual_core +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +440 4 e 9 slow_cpu +444 1 e 1 nmi +445 1 e 1 iommu +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 reserved_memory + + + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM +8 0 400Mhz +8 1 333Mhz +8 2 266Mhz +8 3 200Mhz +9 0 off +9 1 87.5% +9 2 75.0% +9 3 62.5% +9 4 50.0% +9 5 37.5% +9 6 25.0% +9 7 12.5% + +checksums + +checksum 392 983 984 + + Property changes on: src/mainboard/msi/ms9185/cmos.layout ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/mainboard.c =================================================================== --- src/mainboard/msi/ms9185/mainboard.c (revision 0) +++ src/mainboard/msi/ms9185/mainboard.c (revision 0) @@ -0,0 +1,12 @@ +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <device/pci_ops.h> +#include "chip.h" + +#if CONFIG_CHIP_NAME == 1 +struct chip_operations mainboard_msi_ms9185_ops = { + CHIP_NAME("MSI ms9185 mainboard") +}; +#endif Property changes on: src/mainboard/msi/ms9185/mainboard.c ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/get_bus_conf.c =================================================================== --- src/mainboard/msi/ms9185/get_bus_conf.c (revision 0) +++ src/mainboard/msi/ms9185/get_bus_conf.c (revision 0) @@ -0,0 +1,121 @@ +#include <console/console.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <string.h> +#include <stdint.h> +#if CONFIG_LOGICAL_CPUS==1 +#include <cpu/amd/dualcore.h> +#endif + +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + +// Global variables for MB layouts and these will be shared by irqtable mptable and acpi_tables +struct mb_sysconf_t mb_sysconf; + +static unsigned pci1234x[] = +{ //Here you only need to set value in pci1234 for HT-IO that could be installed or not + //You may need to preset pci1234 for HTIO board, please refer to src/northbridge/amd/amdk8/get_sblk_pci1234.c for detail + 0x0000ff0, + 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0 +}; +static unsigned hcdnx[] = +{ //HT Chain device num, actually it is unit id base of every ht device in chain, assume every chain only have 4 ht device at most + 0x20202020, + 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +}; + +extern void get_sblk_pci1234(void); + +static unsigned get_bus_conf_done = 0; + +void get_bus_conf(void) +{ + + unsigned apicid_base; + + device_t dev; + int i; + struct mb_sysconf_t *m; + + if(get_bus_conf_done==1) return; //do it only once + + get_bus_conf_done = 1; + + sysconf.mb = &mb_sysconf; + + m = sysconf.mb; + + sysconf.hc_possible_num = sizeof(pci1234x)/sizeof(pci1234x[0]); + + for(i=0;i<sysconf.hc_possible_num; i++) { + sysconf.pci1234[i] = pci1234x[i]; + sysconf.hcdn[i] = hcdnx[i]; + } + + get_sblk_pci1234(); + + sysconf.sbdn = (sysconf.hcdn[0] >> 8) & 0xff; + m->sbdn2 = sysconf.hcdn[0] & 0xff; // bcm5780 + + m->bus_bcm5785_0 = (sysconf.pci1234[0] >> 16) & 0xff; + m->bus_bcm5780[0] = m->bus_bcm5785_0; + + /* bcm5785 */ + dev = dev_find_slot(m->bus_bcm5785_0, PCI_DEVFN(sysconf.sbdn,0)); + if (dev) { + m->bus_bcm5785_1 = pci_read_config8(dev, PCI_SECONDARY_BUS); + dev = dev_find_slot(m->bus_bcm5785_1, PCI_DEVFN(0xd,0)); + if(dev) { + m->bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS); +#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE + m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS); + m->bus_isa++; + printk_debug("bus_isa=%d\n",m->bus_isa); +#endif + } + } + else { + printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5785_0, sysconf.sbdn); + } + + /* bcm5780 */ + for(i = 1; i < 7; i++) { + dev = dev_find_slot(m->bus_bcm5780[0], PCI_DEVFN(m->sbdn2 + i - 1,0)); + if(dev) { + m->bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS); +#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE + m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS); + m->bus_isa++; + printk_debug("bus_isa=%d\n",m->bus_isa); +#endif + + } + else { + printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5780[0], m->sbdn2+i-1); + } + } + + +/*I/O APICs: APIC ID Version State Address*/ +#if CONFIG_LOGICAL_CPUS==1 + apicid_base = get_apicid_base(3); +#else + apicid_base = CONFIG_MAX_PHYSICAL_CPUS; +#endif + for(i=0;i<3;i++) + m->apicid_bcm5785[i] = apicid_base+i; +} Property changes on: src/mainboard/msi/ms9185/get_bus_conf.c ___________________________________________________________________ Name: svn:executable + * Index: src/mainboard/msi/ms9185/cache_as_ram_auto.c =================================================================== --- src/mainboard/msi/ms9185/cache_as_ram_auto.c (revision 0) +++ src/mainboard/msi/ms9185/cache_as_ram_auto.c (revision 0) @@ -0,0 +1,350 @@ +#define ASSEMBLY 1 +#define __ROMCC__ + +#define RAMINIT_SYSINFO 1 +#define CACHE_AS_RAM_ADDRESS_DEBUG 0 + +#define SET_NB_CFG_54 1 + +//used by raminit +#define QRANK_DIMM_SUPPORT 1 + +//used by incoherent_ht +//#define K8_SCAN_PCI_BUS 1 +//#define K8_ALLOCATE_IO_RANGE 1 + + +//used by init_cpus and fidvid +#define K8_SET_FIDVID 1 +//if we want to wait for core1 done before DQS training, set it to 0 +#define K8_SET_FIDVID_CORE0_ONLY 1 + +#define DEBUG_SMBUS 1 + +#include <stdint.h> +#include <device/pci_def.h> +#include <device/pci_ids.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <cpu/x86/lapic.h> +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" + +#if 0 +static void post_code(uint8_t value) { +#if 1 + int i; + for(i=0;i<0x80000;i++) { + outb(value, 0x80); + } +#endif +} +#endif + +#include <cpu/amd/model_fxx_rev.h> +#include "southbridge/broadcom/bcm5785/bcm5785_early_smbus.c" +#include "northbridge/amd/amdk8/raminit.h" +#include "cpu/amd/model_fxx/apic_timer.c" +#include "lib/delay.c" + +#if CONFIG_USE_INIT == 0 + #include "lib/memcpy.c" +#endif + + +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/amd/amdk8/reset_test.c" +#include "northbridge/amd/amdk8/debug.c" +#include "superio/NSC/pc87417/pc87417_early_serial.c" +#include "cpu/amd/mtrr/amd_earlymtrr.c" +#include "cpu/x86/bist.h" + +#include "northbridge/amd/amdk8/setup_resource_map.c" + +#define SERIAL_DEV PNP_DEV(0x2e, PC87417_SP1) +#define RTC_DEV PNP_DEV(0x2e, PC87417_RTC) +#include "southbridge/broadcom/bcm5785/bcm5785_early_setup.c" +static void memreset_setup(void) +{ +} + +static void memreset(int controllers, const struct mem_controller *ctrl) +{ +} + +static inline void activate_spd_rom(const struct mem_controller *ctrl) +{ +#define SMBUS_SWITCH1 0x70 +#define SMBUS_SWITCH2 0x72 + unsigned device = (ctrl->channel0[0]) >> 8; + smbus_send_byte(SMBUS_SWITCH1, device & 0x0f); + smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f ); +} + +#if 0 +static inline void change_i2c_mux(unsigned device) +{ +#define SMBUS_SWITCH1 0x70 +#define SMBUS_SWITCH2 0x72 + smbus_send_byte(SMBUS_SWITCH1, device & 0x0f); + smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f ); +} +#endif + + + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#include "northbridge/amd/amdk8/amdk8_f.h" +#include "northbridge/amd/amdk8/coherent_ht.c" + +#include "northbridge/amd/amdk8/incoherent_ht.c" + +#include "northbridge/amd/amdk8/raminit_f.c" + +#include "sdram/generic_sdram.c" + + /* msi does not want the default */ +#include "resourcemap.c" + +#include "cpu/amd/dualcore/dualcore.c" + +#define RC0 (0x10<<8) +#define RC1 (0x01<<8) + +#define DIMM0 0x50 +#define DIMM1 0x51 +#define DIMM2 0x52 +#define DIMM3 0x53 +#define DIMM4 0x54 +#define DIMM5 0x55 +#define DIMM6 0x56 +#define DIMM7 0x57 + + +#include "cpu/amd/car/copy_and_run.c" +#include "cpu/amd/car/post_cache_as_ram.c" + +#include "cpu/amd/model_fxx/init_cpus.c" + +#include "cpu/amd/model_fxx/fidvid.c" + +#if USE_FALLBACK_IMAGE == 1 + +#include "northbridge/amd/amdk8/early_ht.c" + +void failover_process(unsigned long bist, unsigned long cpu_init_detectedx) +{ + + /* Is this a cpu only reset? Is this a secondary cpu? */ + if ((cpu_init_detectedx) || (!boot_cpu())) { + if (last_boot_normal()) { // RTC already inited + goto normal_image; + } else { + goto fallback_image; + } + } + /* Nothing special needs to be done to find bus 0 */ + /* Allow the HT devices to be found */ + + enumerate_ht_chain(); + + bcm5785_enable_rom(); + + bcm5785_enable_lpc(); + + //enable RTC + pc87417_enable_dev(RTC_DEV); + + /* Is this a deliberate reset by the bios */ +// post_code(0x22); + if (bios_reset_detected() && last_boot_normal()) { + goto normal_image; + } + /* This is the primary cpu how should I boot? */ + else if (do_normal_boot()) { + goto normal_image; + } + else { + goto fallback_image; + } + normal_image: +// post_code(0x23); + __asm__ volatile ("jmp __normal_image" + : /* outputs */ + : "a" (bist), "b" (cpu_init_detectedx) /* inputs */ + ); + + fallback_image: +// post_code(0x25); + ; + +} +#endif + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx); + +void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + +#if USE_FALLBACK_IMAGE == 1 + failover_process(bist, cpu_init_detectedx); +#endif + real_main(bist, cpu_init_detectedx); + +} + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + static const uint16_t spd_addr[] = { + //first node + RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6, + RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7, +#if CONFIG_MAX_PHYSICAL_CPUS > 1 + //second node + RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6, + RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7, +#endif + + }; + + struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); + + int needs_reset; + unsigned bsp_apicid = 0; + + if (bist == 0) { + bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); + } + +// post_code(0x32); + + pc87417_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + +// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE); + + /* Halt if there was a built in self test failure */ + report_bist_failure(bist); + + print_debug("*sysinfo range: ["); print_debug_hex32(sysinfo); print_debug(","); print_debug_hex32((unsigned long)sysinfo+sizeof(struct sys_info)); print_debug(")\r\n"); + + setup_ms9185_resource_map(); +#if 0 + dump_pci_device(PCI_DEV(0, 0x18, 0)); + dump_pci_device(PCI_DEV(0, 0x19, 0)); +#endif + + print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n"); + + setup_coherent_ht_domain(); + + wait_all_core0_started(); +#if CONFIG_LOGICAL_CPUS==1 + // It is said that we should start core1 after all core0 launched + /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain, + * So here need to make sure last core0 is started, esp for two way system, + * (there may be apic id conflicts in that case) + */ + start_other_cores(); +//bx_a010- wait_all_other_cores_started(bsp_apicid); +#endif + + /* it will set up chains and store link pair for optimization later */ + ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn + + bcm5785_early_setup(); + + +#if 0 + //it your CPU min fid is 1G, you can change HT to 1G and FID to max one time. + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); +#endif + +#if K8_SET_FIDVID == 1 + + { + msr_t msr; + msr=rdmsr(0xc0010042); + print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n"); + + } + + enable_fid_change(); + + enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); + + init_fidvid_bsp(bsp_apicid); + + // show final fid and vid + { + msr_t msr; + msr=rdmsr(0xc0010042); + print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n"); + + } +#endif + +#if 1 + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); + + // fidvid change will issue one LDTSTOP and the HT change will be effective too + if (needs_reset) { + print_info("ht reset -\r\n"); + soft_reset(); + } +#endif + allow_all_aps_stop(bsp_apicid); + + //It's the time to set ctrl in sysinfo now; + fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); + + enable_smbus(); + +#if 0 + int i; + for(i=0;i<2;i++) { + activate_spd_rom(sysinfo->ctrl+i); + dump_smbus_registers(); + } +#endif + +#if 0 + int i; + for(i=1;i<256;i<<=1) { + change_i2c_mux(i); + dump_smbus_registers(); + } +#endif + + memreset_setup(); + + //do we need apci timer, tsc...., only debug need it for better output + /* all ap stopped? */ +// init_timer(); // Need to use TMICT to synconize FID/VID + + sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); + +#if 0 + print_pci_devices(); +#endif + +#if 0 +// dump_pci_devices(); + dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98); + dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98); +#endif + + post_cache_as_ram(); + + +} Property changes on: src/mainboard/msi/ms9185/cache_as_ram_auto.c ___________________________________________________________________ Name: svn:executable + * Index: targets/msi/ms9185/Config.lb =================================================================== --- targets/msi/ms9185/Config.lb (revision 0) +++ targets/msi/ms9185/Config.lb (revision 0) @@ -0,0 +1,73 @@ +# Sample config file for +# the msi ms9185 +# This will make a target directory of ./ms9185 + +target ms9185 +mainboard msi/ms9185 + +# ms9185 +romimage "normal" +# 36k for ATI option rom + option ROM_SIZE = 512*1024-36*1024 +# option ROM_SIZE = 524288 +# option ROM_SIZE = 425984 +# 64K for Etherboot +# option ROM_SIZE = 458752 + option USE_FALLBACK_IMAGE=0 +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x18800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" +# payload ../../../payloads/tg3--ide_disk.zelf +# payload ../../../payloads/filo.elf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo.zelf +# payload ../../../payloads/tg3--filo_hda2.zelf +# payload ../../../payloads/tg3.zelf +# payload ../../../../payloads/tg3_vga.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga.zelf +# payload /filo.elf + payload /tg3--filo.elf +# payload ../../../../payloads/e1000_vga.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf +# payload ../../../payloads/tg3_com2.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf +end + +romimage "fallback" + option USE_FALLBACK_IMAGE=1 +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x19800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" +# payload ../../../payloads/tg3--ide_disk.zelf +# payload ../../../payloads/filo.elf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo.zelf +# payload ../../../payloads/tg3--filo_hda2.zelf +# payload ../../../payloads/tg3.zelf +# payload ../../../../payloads/tg3_vga.zelf +# payload ../../../../payloads/memtest +# payload ../../../../payloads/e1000_vga.zelf +# payload ../../../../payloads/filo_hda.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga.zelf +# payload /filo.elf + payload /tg3--filo.elf +# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf +# payload ../../../payloads/tg3_com2.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf +end + +buildrom ./ms9185.lxb ROM_SIZE "normal" "fallback" Property changes on: targets/msi/ms9185/Config.lb ___________________________________________________________________ Name: svn:executable + * Signed-off-by: bxshi <bxshi(a)msik.com.cn> *****CONFIDENTIAL INFORMATION***** This email is intended only for the use of the person or entity to whom it is addressed and contains information that may be subject to and/or may be restricted from disclosure by contract or applicable law. If you are not the intended recipient of this email, be advised that any disclosure, copy, distribution or use of the contents of this message is strictly prohibited. If you are not the intended recipient of this email, please notify the sender that you have received this in error by replying to this message. Then, please delete it from your system. Thank you.

7 11

[LinuxBIOS] Thank you
by Raffaele de Leon 29 Oct '06

29 Oct '06

Hi Uwe and Stefan, thank you both for your advice. Uwe, I would post my laptop details etc but to get the SuperIO chip no. I imagine I would have to open the case etc. Normally this is no problem but I'd void the warranty unfortunately. All the other info I included in the last post. Seems I'm a bit out of my depth with the main thrust of LinuxBIOS but I wish you all the best with the project. Raffaele

1 0

[LinuxBIOS] Cache as ram on VIA C3/C7 cpu
by vc_6＠sina.com 29 Oct '06

29 Oct '06

I am trying to implement CAR on VIA C3 / C7 cpu. After DRAM initialization, resetting the CACHE and switching the stack to DRAM, the system will hang. How can i do? Any suggestions? VIA C3/C7 cpu 64k L1 Data Cache, 64K L1 Instruction Cache 128K L2 Cache with 32-way set associativity Thanks ------------------------------------------------------------------- 惠普dc5750高性能低功耗( http://ad4.sina.com.cn/sina/limeng3/mail_zhuiyu/2006/mail_zhuiyu_20061016.h… ) =================================================================== 注册新浪2G免费邮箱（ http://mail.sina.com.cn/chooseMode.html ）

2 1

[LinuxBIOS] Please let me know the status for this chipset
by Raffaele de Leon 29 Oct '06

29 Oct '06

Hi guys Looks like great work here. I downloaded and built LinuxBIOS V2 solely to use flashrom, however when I executed the binary it went through all the probing and decided "no eeprom found", before promptly turning the computer off. All I want to do is read and write the contents of my BIOS while running Linux - I'm sort of ok with my proprietary BIOS for now! My BIOS chip, as reported by UniFlash, is an AMIC A29040(A/B)/5V. It also says the organisation is "sectored 8x64k (512k)" - dunno if that's useful. The chipset is Intel 845PE and that's running a Pentium 4 2.8 GHz in an Fujitsu Siemens Amilo D 7830 Laptop. I'd really appreciate it if someone could let me know how long I'm looking at waiting to be able to use "flashrom". In fact, I don't know any C but I'm always willing to have a poke around and if I could somehow use the addressing and data that's coded into UniFlash (it's OSS) to add my motherboard to flashbios' knowhow, a few pointers would set me into happy tinkering mode. Or indeed if there are any other methods of reading from and/or writing to the BIOS under Linux - again, I'd be much indebted. Kind regards, Raffaele de Leon

3 2

[LinuxBIOS] r2477 build service
by LinuxBIOS information 29 Oct '06

29 Oct '06

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "uwe" checked in revision 2477 to the LinuxBIOS source repository and caused the following changes: Change Log: Rename E7520 to e7520, and E7525 to e7525 in the code. The next commit will then rename the E7520 and E7525 directories respectively. Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Build Log: Configuration of dell:s1850 has ben broken Configuration of intel:jarrell has ben broken Configuration of supermicro:x6dai_g has ben broken Configuration of supermicro:x6dhe_g has ben broken Configuration of supermicro:x6dhe_g2 has ben broken Configuration of supermicro:x6dhr_ig has ben broken Configuration of supermicro:x6dhr_ig2 has ben broken If something broke during this checkin please be a pain in uwe's neck until the issue is fixed. If this issue is not fixed within 24h the revision will be backed out. Yours truely, LinuxBIOS automatic build system

6 10

[LinuxBIOS] r2481 - trunk/LinuxBIOSv2/util/abuild
by svn＠openbios.org 28 Oct '06

28 Oct '06

Author: stepan Date: 2006-10-28 18:03:37 +0200 (Sat, 28 Oct 2006) New Revision: 2481 Modified: trunk/LinuxBIOSv2/util/abuild/abuild.1 Log: small tracker test (trivial change). closes #3 fix bug report address Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/LinuxBIOSv2/util/abuild/abuild.1 =================================================================== --- trunk/LinuxBIOSv2/util/abuild/abuild.1 2006-10-28 16:00:24 UTC (rev 2480) +++ trunk/LinuxBIOSv2/util/abuild/abuild.1 2006-10-28 16:03:37 UTC (rev 2481) @@ -56,7 +56,7 @@ .B "\-V, \-\-version" Show version information and exit. .SH BUGS -Please report any bugs at http://bugzilla.openbios.org/. +Please report any bugs at http://tracker.linuxbios.org/. .SH LICENCE .B abuild is covered by the GNU General Public License (GPL), version 2 or later.

1 0

[LinuxBIOS] r2480 - trunk/LinuxBIOSv2/util/abuild
by svn＠openbios.org 28 Oct '06

28 Oct '06

Author: stepan Date: 2006-10-28 18:00:24 +0200 (Sat, 28 Oct 2006) New Revision: 2480 Modified: trunk/LinuxBIOSv2/util/abuild/abuild.1 Log: Small tracker test (trivial change). closes #3 Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/LinuxBIOSv2/util/abuild/abuild.1 =================================================================== --- trunk/LinuxBIOSv2/util/abuild/abuild.1 2006-10-27 18:22:13 UTC (rev 2479) +++ trunk/LinuxBIOSv2/util/abuild/abuild.1 2006-10-28 16:00:24 UTC (rev 2480) @@ -31,7 +31,7 @@ Use payloads in .B "<dir>" to build images. This will run payload.sh in that directory to find out the -path of the payload +path of the payload. .TP .B "\-t, \-\-target <vendor/board>" Attempt to build target vendor/board only.

1 0

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot October 2006