coreboot September 2002

coreboot@coreboot.org

57 participants
84 discussions

DOC vs. IDE
by Christopher Bergeron 23 Oct '02

23 Oct '02

Can anyone give me advice on what will acheive the fastest boot time? My options are the LinuxBIOS coupled with a DOC root or with root configured on hda1 (IDE). I boot into X and I'll need standard modules loaded. I'd like to fit the entire install on a DOC but only IF I'll get a faster load/boot. Would a combination be faster or just DOC ? Much thanks in advance to anyone that can provide advice... -Chris Bergeron

11 19

just 2 boards supported by linuxbios
by Karthik Bala Guru 05 Oct '02

05 Oct '02

Hi, i read from a pdf that linuxbios supports just two motherboards . Is it true ? What r the boards available in INDIAN CHENNAI or BANGLORE or HYDERABAD or MUMBAI market support linuxbios ? I have rtlinux in a floppy . Could i use linuxbios and port it into a x86 board ? where should i start with ?? If so, plz tell me some clear steps ... Xpecting ur help, karthik bala guru ________________________________________________________________________ Missed your favourite TV serial last night? Try the new, Yahoo! TV. visit http://in.tv.yahoo.com

5 8

porting rtlinux into x86
by Karthik Bala Guru 05 Oct '02

05 Oct '02

Hi, If linuxbios boots other linux ... then it should act as a BIOS and boot rtlinux ??? am i correct till now ? I have rtlinux in a floppy . Could i use linuxbios and port it into a x86 board ? where should i start with ?? If so, plz tell me some clear steps ... Xpecting ur help, karthik bala guru ________________________________________________________________________ Missed your favourite TV serial last night? Try the new, Yahoo! TV. visit http://in.tv.yahoo.com

2 3

nonsense C/H/S values for CF (used in ide)
by Q-ha Park 03 Oct '02

03 Oct '02

I have a board with gx1, pc97317 and cs5530a with one ide slot. I've been booting linux with Phoenix bios so far with no problems, and I tried linuxBIOS to boot linux. but I noticed strange C/H/S values like "init_drive sectors_per_track=[768], num_heads=[768], num_cylinders=[768]". and it failed to boot. does anyone have similar problems like this? Phoenix bios sees the device and read the values correctly... thanks, Q

2 5

RE: No IRQ Known for interrupt pin A of device 02:04.0. Please try using pci=biosirq
by David Xiong 30 Sep '02

30 Sep '02

The mainboard is K7SEM and irq_tables.c is already in the source tree. I run the program getpir and get an irq_tables.c file which is the same as the one in the source tree. The program util/getpir reports 6 slot found, whether I plug in the multimedia card or not, and produce exact the same irq_tables.c. And the option HAVE_PIRQ_TABLE=1 is set in the config file of the source tree. I traced into the kernel source and found that the original BIOS set IRQ when POST, but linuxbios does not do so. The IRQ is 0 when start up with linuxbios. When the driver of the multimedia card comes up, it find the card has not an IRQ. Then the driver try to get one from the irq_table, but the PCI device is not in the irq_table, so it can not find one or assign one to the device. What else can I do? Can I hard code one irq to the card? Thanks! David Xiong ---------------------------------------------------------------------------------------- Date: Sun, 29 Sep 2002 12:23:19 -0600 (MDT) From: Ronald G Minnich <rminnich(a)lanl.gov> To: "Steve M. Gehlbach" <steve(a)nexpath.com> cc: <linuxbios(a)clustermatic.org> Subject: RE: No IRQ Known for interrupt pin A of device 02:04.0. Please try using pci=biosirq On Sun, 29 Sep 2002, Steve M. Gehlbach wrote: > You need to make and run the program util/getpir (using the original BIOS, > running Linux) to make the file irq_tables.c, then copy that file into the > mainboard directory, and set the option HAVE_PIRQ_TABLE=1. Linuxbios when > it starts will copy this file into the shadowed RAM at 0xF0000, where Linux > can find it during startup. This allows Linux to route the irqs. exactly. If this is a new board I need all the info so I can put it in the source tree. ron

3 6

Kernel patches for VIA Eden chipsets.
by CMZ 30 Sep '02

30 Sep '02

Hi, what's the kernel patches that I can use for Via chipsets? /src/kernel_patches are mostly SiS based, and does actual SDR initialization works for DDR too? Thanks! CM.

2 1

OT: Diamond Stealth 64 DRAM PCI on Linux Framebuffer w/o Option Rom?
by Lee 29 Sep '02

29 Sep '02

Dear LinuxBiosers, I'm afraid this topic is a bit off topic, but I thought you guys would be the best to ask as LinuxBios doesn't load option roms. I have a Diamond Stealth 64 Dram PCI card which I have removed the option rom from (and placed in an antistatic foam eprom case.) I want to use it for dual monitor support, but had to remove the option rom as it wasn't designed for multi-card operation. I am wondering if this thing can be used with Linux's framebuffer support?? My other card is a Nvidia GeForce2 64MB AGP. I figure I may have to assign it some settings, I'm not sure. I haven't put it into the target machine yet, but I have tested it booting with a Cirrus Logic 5422 w/ Option Rom on a different machine and it is detected by 95, but not used. Thanking you in advance, Lee Edward Causier.

1 0

PCI: No IRQ Known for interrupt pin A of device 02:04.0. Please try using pci=biosirq
by David Xiong 29 Sep '02

29 Sep '02

I have Linuxbios boot from DOC successfuly. But I can not get my 2-channel-video-monitor-card up. When I load the driver, it shows PCI: No IRQ Known for interrupt pin A of device 02:04.0. Please try using pci=biosirq The driver can not get IRQ, and it can not work. If I boot from BIOS with the same kernel , the card can work correctly. I noticed that BIOS set IRQ into the card but linuxbios does not do so. Can you tell me what shall I do? Thanks a lot. David Xiong

3 3

PCChips M758LMR+
by Todd E. Johnson 29 Sep '02

29 Sep '02

Hello folks, I have the PCChips M758LMR+, and I am extremely interested in this excellent project! Does anyone have example LinuxBios boot times with this board? While grepping for additional information to get started, I came across: http://www.acl.lanl.gov/linuxbios/config/index.html However, it does not contain this board, as well, I encounter a 404 when attempting to create a config for another board. Besides the FAQ, are there any other resources to help me get started with this system? Thanks in advance! Regards, Todd E. Johnson http://www.groomlakelabs/grandamp/ tejohnson(a)yahoo.com

2 1

noob
by Trung Hoang 28 Sep '02

28 Sep '02

im quite a noob at linuxbios. i read about it in a cool magazine or somewhere =B i went to the website. and went to download. but it points me to sourceforge, where i can download FREEBIOS. is this an alias for lunixBios or something or what am i missing here? cheers

2 1

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot September 2002