Author: rminnich Date: 2008-08-28 00:45:18 +0200 (Thu, 28 Aug 2008) New Revision: 829
Added: coreboot-v3/arch/x86/amd/model_fxx/init_cpus.c Log: This is an intermediate state of the initcpus support for k8.
This is the CPU startup code. I'm documenting and cleaning it up (removing all support for pre-f2 CPUs) and trying to get it to the point that people can see what's going on. This code is needed for k8 initram.
I'm adding doxygen comments, all errors are mine, and corrections are welcome.
Signed-off-by: Ronald G. Minnich rminnich@gmai.com Acked-by: Ronald G. Minnich rminnich@gmai.com
Added: coreboot-v3/arch/x86/amd/model_fxx/init_cpus.c =================================================================== --- coreboot-v3/arch/x86/amd/model_fxx/init_cpus.c (rev 0) +++ coreboot-v3/arch/x86/amd/model_fxx/init_cpus.c 2008-08-27 22:45:18 UTC (rev 829) @@ -0,0 +1,451 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2005 Advanced Micro Devices, Inc. + * Copyright (C) 2007 Stefan Reinauer + * Copyright (C) 2008 Ronald G. Minnich rminnich@gmail.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ +#include <mainboard.h> +#include <types.h> +#include <lib.h> +#include <console.h> +#include <globalvars.h> +#include <device/device.h> +#include <device/pci.h> +#include <string.h> +#include <msr.h> +#include <io.h> +#include <cpu.h> +#include <amd/k8/k8.h> +#include <mc146818rtc.h> +#include <spd.h> + +// for rev F, need to set FID to max +#define K8_SET_FIDVID 1 + +#ifndef K8_SET_FIDVID_CORE0_ONLY + /* MSR FIDVID_CTL and FIDVID_STATUS are shared by cores, so may don't need to do twice*/ + #define K8_SET_FIDVID_CORE0_ONLY 1 +#endif + +static void print_initcpu8 (const char *strval, unsigned int val) +{ + printk(BIOS_DEBUG, "%s%02x\n", strval, val); +} + +static void print_initcpu8_nocr (const char *strval, unsigned val) +{ + printk(BIOS_DEBUG, "%s%02x", strval, val); +} + + +static void print_initcpu16 (const char *strval, unsigned val) +{ + printk(BIOS_DEBUG, "%s%04x\n", strval, val); +} + +static inline void print_initcpu(const char *strval, unsigned val) +{ + printk(BIOS_DEBUG, "%s%08x\n", strval, val); + +} + +typedef void (*process_ap_t)(unsigned apicid, void *gp); +/* See page 330 of Publication # 26094 Revision: 3.30 Issue Date: February 2006 + * for APIC id discussion + */ +/** + * for_each_ap + * iterate over all APs and have them run a function. + * The behaviour is modified by the core_range parameter + * @param bsp_apicid The BSP APIC ID number + * @param core_range modifier for the range of cores to run on: + * core_range = 0 : all cores + * core range = 1 : core 0 only + * core range = 2 : cores other than core0 + * @param process pointer to the function to run + * @param gp general purpose argument to be passed as a parameter to the function + */ +static void for_each_ap(unsigned bsp_apicid, unsigned core_range, process_ap_t process_ap, void *gp) +{ + /* Assume the OS will not change our APIC ID. Why does this matter? Because some of the setup + * we do for other cores may depend on it not being changed. + */ + unsigned int ap_apicid; + + unsigned int nodes; + unsigned int siblings = 0; + unsigned int disable_siblings = 1; + unsigned int e0_later_single_core; + unsigned int nb_cfg_54; + int i,j; + + /* The get_nodes function is defined in northbridge/amd/k8/coherent_ht.c */ + nodes = get_nodes(); + + /* if the get_option fails siblings remain disabled. */ + disable_siblings = !CONFIG_LOGICAL_CPUS; + get_option(&disable_siblings, "dual_core"); + + /* There is an interesting problem in different steppings. See page 373. The interpretation of the + * APIC ID bits is different. To determine which order is used, check bit 54 of the + /* here we assume that all nodes are the same stepping. If not, "otherwise we can use use nb_cfg_54 from bsp for all nodes" */ + nb_cfg_54 = read_nb_cfg_54(); + + + for(i=0; i<nodes;i++) { + e0_later_single_core = 0; + /* Page 166. This field indicates the number of cores, with 0 meaning 1, 1 meaning 2, and all else reserved */ + j = ((pci_conf1_read_config32(PCI_BDF(0, 0x18+i, 3), NORTHBRIDGE_CAP) >> NBCAP_CmpCap_SHIFT) & NBCAP_CmpCap_MASK); + if(nb_cfg_54) { + if(j == 0 ) // if it is single core, we need to increase siblings for apic calculation + J = 1; + } + siblings = j; + + unsigned jstart, jend; + + if(core_range == 2) { + jstart = 1; + } + else { + jstart = 0; + } + + if (disable_siblings || (core_range==1)) { + jend = 0; + } else { + jend = siblings; + } + + + for(j=jstart; j<=jend; j++) { + + ap_apicid = i * (nb_cfg_54?(siblings+1):1) + j * (nb_cfg_54?1:8); + + #if (ENABLE_APIC_EXT_ID == 1) + #if LIFT_BSP_APIC_ID == 0 + if( (i!=0) || (j!=0)) /* except bsp */ + #endif + ap_apicid += APIC_ID_OFFSET; + #endif + + if(ap_apicid == bsp_apicid) continue; + + process_ap(ap_apicid, gp); + + } + } +} + +/** + * lapic remote read + * lapics are more than just an interrupt steering system. They are a key part of inter-processor communication. + * They can be used to start, control, and interrupt other CPUs from the BSP. It is not possible to bring up + * an SMP system without somehow using the APIC. + * CPUs and their attached IOAPICs all have an ID. For convenience, these IDs are unique. + * The communications is packet-based, using (in coreboot) a polling-based strategy. As with most APIC ops, + * the ID is the APIC ID. Even more fun, code can read registers in remote APICs, and this in turn can + * provide us with remote CPU status. + * This function does a remote read given an apic id. It returns the value or an error. It can time out. + * @param apicid Remote APIC id + * @param reg The register number to read + * @param pvalue pointer to int for return value + * @returns 0 on success, -1 on error + */ +static int lapic_remote_read(int apicid, int reg, unsigned int *pvalue) +{ + int timeout; + unsigned status; + int result; + /* Wait for the idle state. Could we enter this with the APIC busy? It's possible. */ + lapic_wait_icr_idle(); + /* The APIC Interrupt Control Registers define the operations and destinations. + * In this case, we set ICR2 to the dest, set the op to REMOTE READ, and set the + * reg (which is 16-bit aligned, it seems, hence the >> 4 + */ + lapic_write(LAPIC_ICR2, SET_LAPIC_DEST_FIELD(apicid)); + lapic_write(LAPIC_ICR, LAPIC_DM_REMRD | (reg >> 4)); + + /* it's started. now we wait. */ + timeout = 0; + + do { + /* note here the ICR is command and status. */ + /* Why don't we use the lapic_wait_icr_idle() above? */ + /* That said, it's a bad idea to mess with this code too much. + * APICs (and their code) are quite fragile. + */ + status = lapic_read(LAPIC_ICR) & LAPIC_ICR_BUSY; + } while (status == LAPIC_ICR_BUSY && timeout++ < 1000); + + /* interesting but the timeout is not checked, hence no error on the send! */ + + timeout = 0; + do { + status = lapic_read(LAPIC_ICR) & LAPIC_ICR_RR_MASK; + } while (status == LAPIC_ICR_RR_INPROG && timeout++ < 1000); + + result = -1; + if (status == LAPIC_ICR_RR_VALID) { + *pvalue = lapic_read(LAPIC_RRR); + result = 0; + } + return result; +} + +#define LAPIC_MSG_REG 0x380 + + +#if K8_SET_FIDVID == 1 +static void init_fidvid_ap(unsigned bsp_apicid, unsigned apicid); +#endif + +static inline __attribute__((always_inline)) void print_apicid_nodeid_coreid(unsigned apicid, struct node_core_id id, const char *str) +{ + #if CONFIG_USE_PRINTK_IN_CAR + printk_debug("%s --- { APICID = %02x NODEID = %02x COREID = %02x} ---\r\n", str, apicid, id.nodeid, id.coreid); + #else + printk(BIOS_DEBUG, str); + printk(BIOS_DEBUG, " ---- {APICID = "); print_debug_hex8(apicid); + printk(BIOS_DEBUG, " NODEID = "), print_debug_hex8(id.nodeid); printk(BIOS_DEBUG, " COREID = "), print_debug_hex8(id.coreid); + printk(BIOS_DEBUG, "} --- \r\n"); + #endif +} + + +/** + * Using the APIC remote read code, wait for the CPU to enter a given state + * This function can time out. + * @param apicid The apicid of the remote CPU + * @param state The state we are waiting for + * @return 0 on success, readback value on error + */ +static unsigned int wait_cpu_state(unsigned apicid, unsigned state) +{ + unsigned readback = 0; + unsigned timeout = 1; + int loop = 2000000; + while(--loop>0) { + if(lapic_remote_read(apicid, LAPIC_MSG_REG, &readback)!=0) continue; + if((readback & 0xff) == state) { + timeout = 0; + break; //target cpu is in stage started + } + } + if(timeout) { + if(readback) { + timeout = readback; + } + } + + return timeout; +} + +/** + * Wait for an AP to start. + * @param ap_apicid the apic id of the CPu + * @param gp arbitrary parameter + */ +static void wait_ap_started(unsigned ap_apicid, void *gp ) +{ + unsigned timeout; + timeout = wait_cpu_state(ap_apicid, 0x33); // started + if(timeout) { + print_initcpu8_nocr("*", ap_apicid); + print_initcpu("*", timeout); + } + else { + print_initcpu8_nocr(" ", ap_apicid); + } +} + +/** + * wait for all apics to start. Make sure we don't wait on ourself. + * @param bsp_apicid The BSP APIC ID + */ +static void wait_all_aps_started(unsigned bsp_apicid) +{ + for_each_ap(bsp_apicid, 0 , wait_ap_started, (void *)0); +} + +/** + * Wait on all other cores to start. This includes cores on bsp, we think. + * @param bsp_apicid The BSP APIC ID + */ +static void wait_all_other_cores_started(unsigned bsp_apicid) // all aps other than core0 +{ + printk(BIOS_DEBUG, "started ap apicid: "); + for_each_ap(bsp_apicid, 2 , wait_ap_started, (void *)0); + printk(BIOS_DEBUG, "\r\n"); +} + +/** + * Stop all APs + * @param bsp_apicid The BSP apic id, to make sure we don't send ourselves the stop + */ +static void allow_all_aps_stop(unsigned bsp_apicid) +{ + lapic_write(LAPIC_MSG_REG, (bsp_apicid<<24) | 0x44); // allow aps to stop +} + +static void STOP_CAR_AND_CPU(void) +{ + disable_cache_as_ram(); // inline + stop_this_cpu(); // inline, it will stop all cores except node0/core0 the bsp .... +} + +#ifndef MEM_TRAIN_SEQ +#define MEM_TRAIN_SEQ 0 +#endif + + +#if MEM_TRAIN_SEQ == 1 +static inline void train_ram_on_node(unsigned nodeid, unsigned coreid, struct sys_info *sysinfo, unsigned retcall); +#endif + +unsigned int init_cpus(unsigned cpu_init_detectedx ,struct sys_info *sysinfo) +{ + unsigned bsp_apicid = 0; + unsigned apicid; + struct node_core_id id; + + /* + * MTRR must be set by this point. + */ + + /* that is from initial apicid, we need nodeid and coreid later */ + id = get_node_core_id_x(); + + + /* NB_CFG MSR is shared between cores, so we need make sure core0 is done at first --- use wait_all_core0_started */ + if(id.coreid == 0) { + set_apicid_cpuid_lo(); /* only set it on core0 */ + #if ENABLE_APIC_EXT_ID == 1 + enable_apic_ext_id(id.nodeid); + #endif + } + + enable_lapic(); +// init_timer(); // We need TMICT to pass msg for FID/VID change + + #if (ENABLE_APIC_EXT_ID == 1) + unsigned initial_apicid = get_initial_apicid(); + #if LIFT_BSP_APIC_ID == 0 + if( initial_apicid != 0 ) // other than bsp + #endif + { + /* use initial apic id to lift it */ + u32 dword = lapic_read(LAPIC_ID); + dword &= ~(0xff<<24); + dword |= (((initial_apicid + APIC_ID_OFFSET) & 0xff)<<24); + + lapic_write(LAPIC_ID, dword); + } + + #if LIFT_BSP_APIC_ID == 1 + bsp_apicid += APIC_ID_OFFSET; + #endif + + #endif + + /* get the apicid, it may be lifted already */ + apicid = lapicid(); + +#if 0 + // show our apicid, nodeid, and coreid + if( id.coreid==0 ) { + if (id.nodeid!=0) //all core0 except bsp + print_apicid_nodeid_coreid(apicid, id, " core0: "); + } + #if 0 + else { //all core1 + print_apicid_nodeid_coreid(apicid, id, " core1: "); + } + #endif + +#endif + + if (cpu_init_detectedx) { + print_apicid_nodeid_coreid(apicid, id, "\r\n\r\n\r\nINIT detected from "); + printk(BIOS_DEBUG, "\r\nIssuing SOFT_RESET...\r\n"); + soft_reset(); + } + + if(id.coreid==0) { + distinguish_cpu_resets(id.nodeid); + // start_other_core(id.nodeid); // start second core in first cpu, only allowed for nb_cfg_54 is not set + } + + //here don't need to wait + lapic_write(LAPIC_MSG_REG, (apicid<<24) | 0x33); // mark the cpu is started + + if(apicid != bsp_apicid) { + unsigned timeout=1; + unsigned loop = 100; + #if K8_SET_FIDVID == 1 + #if (CONFIG_LOGICAL_CPUS == 1) && (K8_SET_FIDVID_CORE0_ONLY == 1) + if(id.coreid == 0 ) // only need set fid for core0 + #endif + init_fidvid_ap(bsp_apicid, apicid); + #endif + + // We need to stop the CACHE as RAM for this CPU, really? + while(timeout && (loop-->0)) { + timeout = wait_cpu_state(bsp_apicid, 0x44); + } + if(timeout) { + print_initcpu8("while waiting for BSP signal to STOP, timeout in ap ", apicid); + } + lapic_write(LAPIC_MSG_REG, (apicid<<24) | 0x44); // bsp can not check it before stop_this_cpu + set_init_ram_access(); + #if MEM_TRAIN_SEQ == 1 + train_ram_on_node(id.nodeid, id.coreid, sysinfo, STOP_CAR_AND_CPU); + #endif + + STOP_CAR_AND_CPU(); + } + + return bsp_apicid; +} + + +static unsigned is_core0_started(unsigned nodeid) +{ + u32 htic; + struct device * device; + device = PCI_DEV(0, 0x18 + nodeid, 0); + htic = pci_conf1_read_config32(device, HT_INIT_CONTROL); + htic &= HTIC_INIT_Detect; + return htic; +} + +static void wait_all_core0_started(void) +{ + //When core0 is started, it will distingush_cpu_resets. So wait for that + unsigned i; + unsigned nodes = get_nodes(); + + printk(BIOS_DEBUG, "core0 started: "); + for(i=1;i<nodes;i++) { // skip bsp, because it is running on bsp + while(!is_core0_started(i)) {} + print_initcpu8_nocr(" ", i); + } + printk(BIOS_DEBUG, "\r\n"); + +} +
-
svn＠coreboot.org