[LinuxBIOS] r2412 - in trunk/LinuxBIOSv2: src/cpu/amd/model_lx src/include/cpu/amd src/northbridge/amd/lx targets/artecgroup/dbe61

Author: rminnich
Date: 2006-09-13 23:59:09 +0200 (Wed, 13 Sep 2006)
New Revision: 2412

Modified:
   trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cpubug.c
   trunk/LinuxBIOSv2/src/cpu/amd/model_lx/model_lx_init.c
   trunk/LinuxBIOSv2/src/cpu/amd/model_lx/vsmsetup.c
   trunk/LinuxBIOSv2/src/include/cpu/amd/lxdef.h
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/chipsetinit.c
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/grphinit.c
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.c
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.h
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridgeinit.c
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/pll_reset.c
   trunk/LinuxBIOSv2/src/northbridge/amd/lx/raminit.c
   trunk/LinuxBIOSv2/targets/artecgroup/dbe61/Config.lb
Log:
changes for the lx and artecgroup mobo
Signed-off-by: Indrek Kruusa
Approved-by: Ronald G. Minnich

Modified: trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cpubug.c
===================================================================
--- trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cpubug.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cpubug.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -349,9 +349,10 @@
 void
 cpubug(void)
 {
+#if 0 //GX3: any CPU bugs to fix here? :)
    msr_t msr;
    int rev;
-#if 0 //GX3
+
    msr = rdmsr(GLCP_CHIP_REVID);

rev = msr.lo & 0xff;

Modified: trunk/LinuxBIOSv2/src/cpu/amd/model_lx/model_lx_init.c
===================================================================
--- trunk/LinuxBIOSv2/src/cpu/amd/model_lx/model_lx_init.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/cpu/amd/model_lx/model_lx_init.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -5,6 +5,7 @@
 #include <cpu/cpu.h>
 #include <cpu/x86/lapic.h>
 #include <cpu/x86/cache.h>
+#include <arch/io.h>

static void vsm_end_post_smi(void)
 {
@@ -27,8 +28,14 @@
    /* Enable the local cpu apics */
    //setup_lapic();

+	// do VSA late init
    vsm_end_post_smi();

+	// Set gate A20 (legacy vsm disables it in late init)
+	printk_debug("A20 (0x92): %d\n",inb(0x92));
+	outb(0x02,0x92);
+	printk_debug("A20 (0x92): %d\n",inb(0x92));
+
    printk_debug("model_lx_init DONE\n");
 };

Modified: trunk/LinuxBIOSv2/src/cpu/amd/model_lx/vsmsetup.c
===================================================================
--- trunk/LinuxBIOSv2/src/cpu/amd/model_lx/vsmsetup.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/cpu/amd/model_lx/vsmsetup.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -6,13 +6,14 @@
 #include <arch/io.h>
 #include <string.h>
 #include <cpu/amd/lxdef.h>
+#include <cpu/amd/vr.h>

-/* what a mess this uncompress thing is. I am not at all happy about how this 
- * was done, but can't fix it yet. RGM
- */
-#warning "Fix the uncompress once linuxbios knows how to do it"
+// andrei: use the /lib copy of nrv2b
 #include "../lib/nrv2b.c"

+#define VSA2_BUFFER			0x60000
+#define VSA2_ENTRY_POINT	0x60020
+
 /* vsmsetup.c derived from vgabios.c. Derived from: */

/*------------------------------------------------------------ -*- C -*-
@@ -67,7 +68,7 @@
  *  negligence or otherwise) arising in any way out of the use of this
  *  software, even if advised of the possibility of such damage.
  *
- *  $Id: Exp $
+ *  $Id: vsmsetup.c,v 1.8 2006/09/08 12:47:57 andrei Exp $
  *--------------------------------------------------------------------*/

/* Modified to be a self sufficient plug in so that it can be used 
@@ -137,29 +138,32 @@
 /* The address arguments to this function are PHYSICAL ADDRESSES */ 
 static void real_mode_switch_call_vsm(unsigned long smm, unsigned long sysm)
 {
+	uint16_t entryHi = (VSA2_ENTRY_POINT & 0xffff0000) >> 4;
+	uint16_t entryLo = (VSA2_ENTRY_POINT & 0xffff);
+
    __asm__ __volatile__ (
    	// paranoia -- does ecx get saved? not sure. This is 
    	// the easiest safe thing to do.
    	"	pushal			\n"
    	/* save the stack */
-		"	mov 	%esp, __stack	\n"
+		"	mov 	%%esp, __stack	\n"
    	"	jmp 	1f		\n"
    	"__stack: .long 0		\n"
    	"1:\n"
-		/* get devfn into %ecx */
-		"	movl    %esp, %ebp	\n"
+		/* get devfn into %%ecx */
+		"	movl    %%esp, %%ebp	\n"
 #if 0
    	/* I'm not happy about that pushal followed by esp-relative references. 
    	  * just do hard-codes for now
    	  */
-		"	movl    8(%ebp), %ecx	\n"
-		"	movl    12(%ebp), %edx	\n"
+		"	movl    8(%%ebp), %%ecx	\n"
+		"	movl    12(%%ebp), %%edx	\n"
 #endif
-		"	movl    $0x10000026, %ecx	\n"
-		"	movl    $0x10000028, %edx	\n"
+		"	movl    %0, %%ecx	\n"
+		"	movl    %1, %%edx	\n"

/* load 'our' gdt */
-		"	lgdt	%cs:__mygdtaddr	\n"
+		"	lgdt	%%cs:__mygdtaddr	\n"

/*  This configures CS properly for real mode. */
    	"	ljmp	$0x28, $__rms_16bit\n"
@@ -170,17 +174,17 @@
    	/* Load the segment registers w/ properly configured segment
    	 * descriptors.  They will retain these configurations (limits,
    	 * writability, etc.) once protected mode is turned off. */
-		"	mov	$0x30, %ax	\n"
-		"	mov	%ax, %ds       	\n"
-		"	mov	%ax, %es       	\n"
-		"	mov	%ax, %fs       	\n"
-		"	mov	%ax, %gs       	\n"
-		"	mov	%ax, %ss       	\n"
+		"	mov	$0x30, %%ax	\n"
+		"	mov	%%ax, %%ds       	\n"
+		"	mov	%%ax, %%es       	\n"
+		"	mov	%%ax, %%fs       	\n"
+		"	mov	%%ax, %%gs       	\n"
+		"	mov	%%ax, %%ss       	\n"

/* Turn off protection (bit 0 in CR0) */
-		"	movl	%cr0, %eax	\n"
-		"	andl	$0xFFFFFFFE, %eax \n"
-		"	movl	%eax, %cr0	\n"
+		"	movl	%%cr0, %%eax	\n"
+		"	andl	$0xFFFFFFFE, %%eax \n"
+		"	movl	%%eax, %%cr0	\n"

/* Now really going into real mode */
    	"	ljmp	$0,  $__rms_real\n"
@@ -190,62 +194,99 @@
    	 * that way we can easily share it between real and protected, 
    	 * since the 16-bit ESP at segment 0 will work for any case. */
    	/* Setup a stack */
-		"	mov	$0x0, %ax	\n"
-		"	mov	%ax, %ss	\n"
-		"	movl	$0x1000, %eax	\n"
-		"	movl	%eax, %esp	\n"
+		"	mov	$0x0, %%ax	\n"
+		"	mov	%%ax, %%ss	\n"
+		"	movl	$0x1000, %%eax	\n"
+		"	movl	%%eax, %%esp	\n"

/* Load our 16 it idt */
-		"	xor	%ax, %ax	\n"
-		"	mov	%ax, %ds	\n"
+		"	xor	%%ax, %%ax	\n"
+		"	mov	%%ax, %%ds	\n"
    	"	lidt	__myidt		\n"

/* Dump zeros in the other segregs */
-		"	mov	%ax, %es       	\n"
+		"	mov	%%ax, %%es       	\n"
    	/* FixMe: Big real mode for gs, fs? */
-		"	mov	%ax, %fs       	\n"
-		"	mov	%ax, %gs       	\n"
-		"	mov	$0x40, %ax	\n"
-		"	mov	%ax, %ds	\n"
-		//"	mov	%cx, %ax	\n"
-		"	movl    $0x10000026, %ecx	\n"
-		"	movl    $0x10000028, %edx	\n"
+		"	mov	%%ax, %%fs       	\n"
+		"	mov	%%ax, %%gs       	\n"
+		"	mov	$0x40, %%ax	\n"
+		"	mov	%%ax, %%ds	\n"
+		//"	mov	%%cx, %%ax	\n"
+		"	movl    %0, %%ecx	\n"
+		"	movl    %1, %%edx	\n"

-		/* run VGA BIOS at 0x6000:0020 */
-		"	lcall	$0x6000, $0x0020\n"
+		/* call the VSA2 entry point address */
+		"	lcall	%2, %3\n"

/* if we got here, just about done. 
    	 * Need to get back to protected mode */
-		"	movl	%cr0, %eax	\n"
-		"	orl	$0x0000001, %eax\n" /* PE = 1 */
-		"	movl	%eax, %cr0	\n"
+		"	movl	%%cr0, %%eax	\n"
+		"	orl	$0x0000001, %%eax\n" /* PE = 1 */
+		"	movl	%%eax, %%cr0	\n"

/* Now that we are in protected mode jump to a 32 bit code segment. */
    	"	data32	ljmp	$0x10, $vsmrestart\n"
    	"vsmrestart:\n"
    	"	.code32\n"
-		"	movw	$0x18, %ax     	\n"
-		"	mov	%ax, %ds       	\n"
-		"	mov	%ax, %es	\n"
-		"	mov	%ax, %fs	\n"
-		"	mov	%ax, %gs	\n"
-		"	mov	%ax, %ss	\n"
+		"	movw	$0x18, %%ax     	\n"
+		"	mov	%%ax, %%ds       	\n"
+		"	mov	%%ax, %%es	\n"
+		"	mov	%%ax, %%fs	\n"
+		"	mov	%%ax, %%gs	\n"
+		"	mov	%%ax, %%ss	\n"

/* restore proper gdt and idt */
-		"	lgdt	%cs:gdtarg	\n"
+		"	lgdt	%%cs:gdtarg	\n"
    	"	lidt	idtarg		\n"

".globl vsm_exit		\n"
    	"vsm_exit:			\n"
-		"	mov	__stack, %esp	\n"
+		"	mov	__stack, %%esp	\n"
    	"	popal			\n"
-		);
+		:: "g" (smm), "g" (sysm), "g" (entryHi), "g" (entryLo));
 }

__asm__ (".text\n""real_mode_switch_end:\n");
 extern char real_mode_switch_end[];

+// andrei: some VSA virtual register helpers: raw read and MSR read

+uint32_t VSA_vrRead(uint16_t classIndex)
+{
+	unsigned eax, ebx, ecx, edx;
+	asm volatile(
+
+		"movw	$0x0AC1C, %%dx			\n"
+		"orl	$0x0FC530000, %%eax		\n"
+		"outl	%%eax, %%dx				\n"
+		"addb	$2, %%dl				\n"
+		"inw	%%dx, %%ax				\n"
+
+		: "=a" (eax), "=b" (ebx), "=c" (ecx), "=d" (edx)
+		: "a" (classIndex)
+		);
+
+	return eax;
+}
+
+uint32_t VSA_msrRead(uint32_t msrAddr)
+{
+	unsigned eax, ebx, ecx, edx;
+	asm volatile(
+
+		"movw	$0x0AC1C, %%dx			\n"
+		"movl	$0x0FC530007, %%eax		\n"
+		"outl	%%eax, %%dx				\n"
+		"addb	$2, %%dl				\n"
+		"inw	%%dx, %%ax				\n"
+
+		: "=a" (eax), "=b" (ebx), "=c" (ecx), "=d" (edx)
+		: "c" (msrAddr)
+		);
+
+	return eax;
+}
+
 void do_vsmbios(void)
 {
    device_t dev;
@@ -272,9 +313,9 @@
    /* the VSA starts at the base of rom - 64 */
    //rom = ((unsigned long) 0) - (ROM_SIZE  + 64*1024);
    
-	rom = 0xfffc0000;
+	rom = 0xfffc8000;

-	buf = (unsigned char *) 0x60000;
+	buf = (unsigned char *) VSA2_BUFFER;
    unrv2b((uint8_t *)rom, buf);
    printk_debug("buf %p *buf %d buf[256k] %d\n",
    	     buf, buf[0], buf[SMM_SIZE*1024]);
@@ -288,18 +329,23 @@
    	return;
    }

-	//memcpy((void *) 0x60000, buf, size);
+	//memcpy((void *) VSA2_BUFFER, buf, size);

//for (i = 0; i < 0x800000; i++)
    //	outb(0xaa, 0x80);

/* ecx gets smm, edx gets sysm */
    printk_err("Call real_mode_switch_call_vsm\n");
-	real_mode_switch_call_vsm(0x10000026, 0x10000028);
+	real_mode_switch_call_vsm(MSR_GLIU0_SMM, MSR_GLIU0_SYSMEM);

/* restart timer 1 */
    outb(0x56, 0x43);
    outb(0x12, 0x41);
+
+	// check that VSA is running OK
+	if(VSA_vrRead(SIGNATURE) == VSA2_SIGNATURE)
+		printk_debug("do_vsmbios: VSA2 VR signature verified\n");
+	else printk_err("do_vsmbios: VSA2 VR signature not valid, install failed!\n");
 }

@@ -520,7 +566,7 @@
    	break;
    case MEMSIZE: 
    	// who cares. 
-		eax = 64 * 1024;
+		eax = 128 * 1024;
    	ret = 0;
    	break;
    case 0x15:
@@ -562,7 +608,7 @@
    // and get it that way. But that's really disgusting.
    for (i = 0; i < 256; i++) {
    	idts[i].cs = 0;
-		codeptr = (char*) 4096 + i * codesize;
+		codeptr = (unsigned char*) 4096 + i * codesize;
    	idts[i].offset = (unsigned) codeptr;
    	memcpy(codeptr, &idthandle, codesize);
    	intbyte = codeptr + 3;
@@ -575,7 +621,7 @@
    // int10. 
    // calling convention here is the same as INTs, we can reuse
    // the int entry code.
-	codeptr = (char*) 0xff065;
+	codeptr = (unsigned char*) 0xff065;
    memcpy(codeptr, &idthandle, codesize);
    intbyte = codeptr + 3;
    *intbyte = 0x42; /* int42 is the relocated int10 */
@@ -584,7 +630,7 @@
       TF bit is set upon call to real mode */
    idts[1].cs = 0;
    idts[1].offset = 16384;
-	memcpy(16384, &debughandle, &end_debughandle - &debughandle);
+	memcpy((void*)16384, &debughandle, &end_debughandle - &debughandle);
 }

@@ -761,10 +807,10 @@
    	*eax=0x860f;
    	break;
    case 0xBEA7:
-		*eax=33;
+		*eax=66;
    	break;
    case 0xBEA4:
-		*eax=333;
+		*eax=500;
    	break;
    }
    return res;

Modified: trunk/LinuxBIOSv2/src/include/cpu/amd/lxdef.h
===================================================================
--- trunk/LinuxBIOSv2/src/include/cpu/amd/lxdef.h	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/include/cpu/amd/lxdef.h	2006-09-13 21:59:09 UTC (rev 2412)
@@ -221,12 +221,19 @@
 #define	CPU_IM_BIST_DATA						0x1731

+/*  ----- GX3 OK  ----  */
+
 /* various CPU MSRs */
 #define CPU_DM_CONFIG0 0x1800
 #define	DM_CONFIG0_UPPER_WSREQ_SHIFT  12
 #define	DM_CONFIG0_LOWER_DCDIS_SET		(1<<8)
 #define	DM_CONFIG0_LOWER_WBINVD_SET	(1<<5)
 #define	DM_CONFIG0_LOWER_MISSER_SET		(1<<1)
+
+#define CPU_DM_CONFIG1							0x1801
+
+#define CPU_DM_PFLOCK							0x1804
+
 /* configuration MSRs */
 #define	CPU_RCONF_DEFAULT						0x1808
 #define		RCONF_DEFAULT_UPPER_ROMRC_SHIFT				24
@@ -236,7 +243,6 @@
 #define		RCONF_DEFAULT_LOWER_SYSTOP_SHIFT			8
 #define		RCONF_DEFAULT_LOWER_SYSRC_SHIFT				0

-/*  ----- GX3 OK  ----  */

#define	CPU_RCONF_BYPASS						0x180A
 #define	CPU_RCONF_A0_BF							0x180B
@@ -421,20 +427,24 @@
 #define	GLPCI_CTRL_LOWER_ME_SET					(1<<0)

#define	GLPCI_ARB			(MSR_PCI + 0x2011)
-#define	GLPCI_ARB_UPPER_BM1_SET					(1<<17)
-#define	GLPCI_ARB_UPPER_BM0_SET					(1<<16)
-#define	GLPCI_ARB_UPPER_CPRE_SET					(1<<15)
-#define	GLPCI_ARB_UPPER_PRE2_SET					(1<<10)
-#define	GLPCI_ARB_UPPER_PRE1_SET					(1<<9)
-#define	GLPCI_ARB_UPPER_PRE0_SET					(1<<8)
-#define	GLPCI_ARB_UPPER_CRME_SET					(1<<7)
-#define	GLPCI_ARB_UPPER_RME2_SET					(1<<2)
-#define	GLPCI_ARB_UPPER_RME1_SET					(1<<1)
-#define	GLPCI_ARB_UPPER_RME0_SET					(1<<0)
-#define	GLPCI_ARB_LOWER_PRCM_SHIFT				24
-#define	GLPCI_ARB_LOWER_FPVEC_SHIFT				16
-#define	GLPCI_ARB_LOWER_RMT_SHIFT				6
-#define	GLPCI_ARB_LOWER_IIE_SET					(1<<8)
+#define	GLPCI_ARB_UPPER_CR_SHIFT				 	(28)
+#define	GLPCI_ARB_UPPER_R2_SHIFT				 	(24)
+#define	GLPCI_ARB_UPPER_R1_SHIFT				 	(20)
+#define	GLPCI_ARB_UPPER_R0_SHIFT				 	(16)
+#define	GLPCI_ARB_UPPER_CH_SHIFT				 	(12)
+#define	GLPCI_ARB_UPPER_H2_SHIFT				 	(8)
+#define	GLPCI_ARB_UPPER_H1_SHIFT				 	(4)
+#define	GLPCI_ARB_UPPER_H0_SHIFT				 	(0)
+#define	GLPCI_ARB_LOWER_COV_SET						(1<<23)
+#define	GLPCI_ARB_LOWER_MSK2_SET				 	(1<<18)
+#define	GLPCI_ARB_LOWER_MSK1_SET				 	(1<<17)
+#define	GLPCI_ARB_LOWER_MSK0_SET				 	(1<<16)
+#define	GLPCI_ARB_LOWER_CPRE_SET					(1<<11)
+#define	GLPCI_ARB_LOWER_PRE2_SET					(1<<10)
+#define	GLPCI_ARB_LOWER_PRE1_SET					(1<<9)
+#define	GLPCI_ARB_LOWER_PRE0_SET					(1<<8)
+#define	GLPCI_ARB_LOWER_BM1_SET						(1<<7)
+#define	GLPCI_ARB_LOWER_BM0_SET						(1<<6)
 #define	GLPCI_ARB_LOWER_PARK_SET					(1<<0)

#define	GLPCI_REN			(MSR_PCI + 0x2014)
@@ -507,24 +517,83 @@

/*  Set up desc addresses from 20 - 3f*/
 /*  This is chip specific!*/
+
+/* ----------   GX3 OK   --------------  */
 #define MSR_GLIU0_BASE1			(MSR_GLIU0 + 0x20)		/*  BM*/
 #define MSR_GLIU0_BASE2			(MSR_GLIU0 + 0x21)		/*  BM*/
+#define MSR_GLIU0_BASE3			(MSR_GLIU0 + 0x22)		/*  BM*/
+#define MSR_GLIU0_BASE4			(MSR_GLIU0 + 0x23)		/*  BM*/
+#define MSR_GLIU0_BASE5			(MSR_GLIU0 + 0x24)		/*  BM*/
+#define MSR_GLIU0_BASE6			(MSR_GLIU0 + 0x25)		/*  BM*/
+
+#define GLIU0_P2D_BMO_0			(MSR_GLIU0 + 0x26)
+#define GLIU0_P2D_BMO_1			(MSR_GLIU0 + 0x27)
+
+#define MSR_GLIU0_SMM			(GLIU0_P2D_BMO_0)
+#define MSR_GLIU0_DMM			(GLIU0_P2D_BMO_1)
+
+#define GLIU0_P2D_R				(MSR_GLIU0 + 0x28)
+#define MSR_GLIU0_SYSMEM		(GLIU0_P2D_R)
+
+#define GLIU0_P2D_RO_0			(MSR_GLIU0 + 0x29)
+#define GLIU0_P2D_RO_1			(MSR_GLIU0 + 0x2A)
+#define GLIU0_P2D_RO_2			(MSR_GLIU0 + 0x2B)
+
 #define MSR_GLIU0_SHADOW			(MSR_GLIU0 + 0x2C)		/*  SCO should only be SC*/
-#define MSR_GLIU0_SYSMEM			(MSR_GLIU0 + 0x28)		/*  RO should only be R*/
-#define MSR_GLIU0_SMM			(MSR_GLIU0 + 0x26)		/*  BMO*/
-#define MSR_GLIU0_DMM			(MSR_GLIU0 + 0x27)		/*  BMO*/

+#define GLIU0_IOD_BM_0			(MSR_GLIU0 + 0xE0)
+#define GLIU0_IOD_BM_1			(MSR_GLIU0 + 0xE1)
+#define GLIU0_IOD_BM_2			(MSR_GLIU0 + 0xE2)
+
+#define GLIU0_IOD_SC_0			(MSR_GLIU0 + 0xE3)
+#define GLIU0_IOD_SC_1			(MSR_GLIU0 + 0xE4)
+#define GLIU0_IOD_SC_2			(MSR_GLIU0 + 0xE5)
+#define GLIU0_IOD_SC_3			(MSR_GLIU0 + 0xE6)
+#define GLIU0_IOD_SC_4			(MSR_GLIU0 + 0xE7)
+#define GLIU0_IOD_SC_5			(MSR_GLIU0 + 0xE8)
+
+
 #define MSR_GLIU1_BASE1			(MSR_GLIU1 + 0x20)		/*  BM*/
 #define MSR_GLIU1_BASE2			(MSR_GLIU1 + 0x21)		/*  BM*/
-#define MSR_GLIU1_SHADOW			(MSR_GLIU1 + 0x2E)		/*  SCO should only be SC*/ // GX3 0x2D -> 0x2E
-#define MSR_GLIU1_SYSMEM			(MSR_GLIU1 + 0x2A)		/*  RO should only be R*/  // GX3 0x29 -> 0x2A
-#define MSR_GLIU1_SMM			(MSR_GLIU1 + 0x23)		/*  BM*/
-#define MSR_GLIU1_DMM			(MSR_GLIU1 + 0x24)		/*  BM*/
-#define MSR_GLIU1_FPU_TRAP		(MSR_GLIU1 + 0x0E3)	/*  FooGlue F0 for FPU*/
+#define MSR_GLIU1_BASE3			(MSR_GLIU1 + 0x22)		/*  BM*/
+#define MSR_GLIU1_BASE4			(MSR_GLIU1 + 0x23)		/*  BM*/
+#define MSR_GLIU1_BASE5			(MSR_GLIU1 + 0x24)		/*  BM*/
+#define MSR_GLIU1_BASE6			(MSR_GLIU1 + 0x25)		/*  BM*/
+#define MSR_GLIU1_BASE7			(MSR_GLIU1 + 0x26)		/*  BM*/
+#define MSR_GLIU1_BASE8			(MSR_GLIU1 + 0x27)		/*  BM*/
+#define MSR_GLIU1_BASE9			(MSR_GLIU1 + 0x28)		/*  BM*/
+#define MSR_GLIU1_BASE10		(MSR_GLIU1 + 0x29)		/*  BM*/

+#define GLIU1_P2D_R_0			(MSR_GLIU1 + 0x2A)
+#define GLIU1_P2D_R_1			(MSR_GLIU1 + 0x2B)
+#define GLIU1_P2D_R_2			(MSR_GLIU1 + 0x2C)
+#define GLIU1_P2D_R_3			(MSR_GLIU1 + 0x2D)
+
+
+#define MSR_GLIU1_SHADOW		(MSR_GLIU1 + 0x2E)
+
+#define MSR_GLIU1_SYSMEM		(GLIU1_P2D_R_0)
+
+#define MSR_GLIU1_SMM			(MSR_GLIU1_BASE4)		/*  BM*/
+#define MSR_GLIU1_DMM			(MSR_GLIU1_BASE5)		/*  BM*/
+
+#define GLIU1_IOD_BM_0			(MSR_GLIU1 + 0xE0)
+#define GLIU1_IOD_BM_1			(MSR_GLIU1 + 0xE1)
+#define GLIU1_IOD_BM_2			(MSR_GLIU1 + 0xE2)
+
+#define GLIU1_IOD_SC_0			(MSR_GLIU1 + 0xE3)
+#define GLIU1_IOD_SC_1			(MSR_GLIU1 + 0xE4)
+#define GLIU1_IOD_SC_2			(MSR_GLIU1 + 0xE5)
+#define GLIU1_IOD_SC_3			(MSR_GLIU1 + 0xE6)
+
+/* ------------------------  */
+
+#define MSR_GLIU1_FPU_TRAP		(GLIU1_IOD_SC_0)	/*  FooGlue F0 for FPU*/
+
+
 /* definitions that are "once you are mostly up, start VSA" type things */
 #define SMM_OFFSET	(0x40400000)
-#define SMM_SIZE		(128)			/* changed SMM_SIZE from 256 KB to 128 KB */
+#define SMM_SIZE		(256)
 #define DMM_OFFSET	(0x0C0000000)
 #define DMM_SIZE		(128)
 #define FB_OFFSET		(0x41000000)

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/chipsetinit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/chipsetinit.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/chipsetinit.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -274,7 +274,7 @@
    if ((msr.lo&0xff) == 0x11)
    	return;

-	totalmem = sizeram() << 20 - 1;
+	totalmem = (sizeram() << 20) - 1;
    totalmem >>= 12; 
    totalmem = ~totalmem;
    totalmem &= 0xfffff;

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/grphinit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/grphinit.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/grphinit.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -1,8 +1,7 @@
 #include <arch/io.h>
 #include <stdint.h>
 #include <cpu/amd/vr.h>
- 
-#define VIDEO_MB	8					// MB of video memory
+#include <console/console.h>

/*
  * Write to a Virtual Register
@@ -33,11 +32,36 @@
  */
 void graphics_init(void)
 {
+	uint16_t wClassIndex, wData, res;
+	
    /* SoftVG initialization */
+	printk_debug("Graphics init...\n");

/* Call SoftVG with the main configuration parameters. */
-	/* NOTE: SoftVG expects the memory size to be given in 512 KB pages */
-	vrWrite((VRC_VG <<  8) + VG_MEM_SIZE, 0x0100 | (VIDEO_MB * 2));
+	/* NOTE: SoftVG expects the memory size to be given in 2MB blocks */
+	
+	wClassIndex = (VRC_VG <<  8) + VG_MEM_SIZE;
+	
+	/*
+	 * Graphics Driver Enabled (13) 			0, NO (lets BIOS controls the GP)
+	 * External Monochrome Card Support(12)		0, NO
+	 * Controller Priority Select(11)			1, Primary
+	 * Display Select(10:8)						0x0, CRT
+	 * Graphics Memory Size(7:1)				VIDEO_MB >> 1,
+	 *											defined in mainboard/../Options.lb
+	 * PLL Reference Clock Bypass(0)			0, Default
+	 */
+
+	/*	 video RAM has to be given in 2MB chunks
+	 *   the value is read @ 7:1 (value in 7:0 looks like /2)
+	 *   so we can add the real value in megabytes
+	 */
+	 
+	wData =  0x0800 | (VIDEO_MB & VG_MEM_MASK);
+	vrWrite(wClassIndex, wData);
+	
+	res = vrRead(wClassIndex);
+	printk_debug("VRC_VG value: 0x%04x\n", res);
 }

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -14,43 +14,8 @@
 #include <cpu/x86/msr.h>
 #include <cpu/x86/cache.h>
 #include <cpu/amd/vr.h>
-#define VIDEO_MB 8

-extern void graphics_init(void);

-#define NORTHBRIDGE_FILE "northbridge.c"
-
-/* todo: add a resource record. We don't do this here because this may be called when 
-  * very little of the platform is actually working.
-  */
-int
-sizeram(void)
-{
-	msr_t msr;
-	int sizem = 0;
-	unsigned short dimm;
-
-	msr = rdmsr(0x20000018);
-	printk_debug("sizeram: %08x:%08x\n", msr.hi, msr.lo);
-
-	/* dimm 0 */
-	dimm = msr.hi;
-	/* installed? */
-	if ((dimm & 7) != 7)
-		sizem = (1 << ((dimm >> 12)-1)) * 8;
-
-
-	/* dimm 1*/
-	dimm = msr.hi >> 16;
-	/* installed? */
-	if ((dimm & 7) != 7)
-		sizem += (1 << ((dimm >> 12)-1)) * 8;
-
-	printk_debug("sizeram: sizem 0x%x\n", sizem);
-	return sizem;
-}
-
-
 /* here is programming for the various MSRs.*/
 #define IM_QWAIT 0x100000

@@ -87,8 +52,16 @@
 #define IOD_BM(msr, pdid1, bizarro, ibase, imask) {msr, {.hi=(pdid1<<29)|(bizarro<<28)|(ibase>>12), .lo=(ibase<<20)|imask}}
 #define IOD_SC(msr, pdid1, bizarro, en, wen, ren, ibase) {msr, {.hi=(pdid1<<29)|(bizarro<<28), .lo=(en<<24)|(wen<<21)|(ren<<20)|(ibase<<3)}}

+#define BRIDGE_IO_MASK (IORESOURCE_IO | IORESOURCE_MEM)

+extern void graphics_init(void);
+extern void cpubug(void);

+void northbridge_init_early(void);
+void chipsetinit(struct northbridge_amd_lx_config *nb);
+void setup_realmode_idt(void);
+void do_vsmbios(void);
+
 struct msr_defaults {
    int msr_no;
    msr_t msr;
@@ -111,16 +84,44 @@
    //{0x1813, {.hi = 0xefff3000, .lo = RRCF_LOW_CD(0xefff0000)}},
    /* now for GLPCI routing */
    /* GLIU0 */
-	P2D_BM(0x10000020, 0x1, 0x0, 0x0, 0xfff80),
-	P2D_BM(0x10000021, 0x1, 0x0, 0x80000, 0xfffe0),
-	P2D_SC(0x1000002c, 0x1, 0x0, 0x0,  0xff03, 0xC0000),
+	P2D_BM(MSR_GLIU0_BASE1, 0x1, 0x0, 0x0, 0xfff80),
+	P2D_BM(MSR_GLIU0_BASE2, 0x1, 0x0, 0x80000, 0xfffe0),
+	P2D_SC(MSR_GLIU0_SHADOW, 0x1, 0x0, 0x0,  0xff03, 0xC0000),
    /* GLIU1 */
-	P2D_BM(0x40000020, 0x1, 0x0, 0x0, 0xfff80),
-	P2D_BM(0x40000021, 0x1, 0x0, 0x80000, 0xfffe0),
-	P2D_SC(0x4000002e, 0x1, 0x0, 0x0,  0xff03, 0xC0000), // GX3 0x4000002d -> 0x4000002e
+	P2D_BM(MSR_GLIU1_BASE1, 0x1, 0x0, 0x0, 0xfff80),
+	P2D_BM(MSR_GLIU1_BASE2, 0x1, 0x0, 0x80000, 0xfffe0),
+	P2D_SC(MSR_GLIU1_SHADOW, 0x1, 0x0, 0x0,  0xff03, 0xC0000),
    {0}
 };

+/* todo: add a resource record. We don't do this here because this may be called when 
+  * very little of the platform is actually working.
+  */
+int
+sizeram(void)
+{
+	msr_t msr;
+	int sizem = 0;
+	unsigned short dimm;
+
+	msr = rdmsr(0x20000018);
+	printk_debug("sizeram: %08x:%08x\n", msr.hi, msr.lo);
+
+	/* dimm 0 */
+	dimm = msr.hi;
+	sizem = (1 << ((dimm >> 12)-1)) * 8;
+
+
+	/* dimm 1*/
+	dimm = msr.hi >> 16;
+	/* installed? */
+	if ((dimm & 7) != 7)
+		sizem += (1 << ((dimm >> 12)-1)) * 8;
+
+	printk_debug("sizeram: sizem 0x%x\n", sizem);
+	return sizem;
+}
+
 /* note that dev is NOT used -- yet */
 static void irq_init_steering(struct device *dev, uint16_t irq_map) {
    /* Set up IRQ steering */
@@ -173,13 +174,19 @@
    /* yank off memory for the SMM handler */
    sizekbytes -= SMM_SIZE;
    sizereg = sizekbytes;
-	sizereg *= 1024;	// convert to bytes
-	sizereg >>= 12;
+	sizereg >>= 2;
    sizereg <<= 8;
    val |= sizereg;
    val |= RAM_PROPERTIES;
    msr.lo = val;
    msr.hi = (val >> 32);
+	
+	// GX3
+	//msr.hi = 0x04FFFC02;
+	//msr.lo = 0x1077BE00;
+	
+	//sizekbytes = 122616;
+
    printk_debug("msr 0x%08X will be set to %08x:%08x\n", CPU_RCONF_DEFAULT, msr.hi, msr.lo);
    wrmsr(CPU_RCONF_DEFAULT, msr);

@@ -199,6 +206,7 @@

size_kb = setup_lx_cache();

+#if 0	// andrei: this is done in northbridge.c SMMGL0Init and SystemInit!
    membytes = size_kb * 1024;
    /* NOTE! setup_lx_cache returns the SIZE OF RAM - RAMADJUST!
      * so it is safe to use. You should NOT at this point call 	
@@ -211,23 +219,7 @@
     * SYSTOP (a.k.a. TOM, or Top of Memory)
     */

-#if 0
-	/* This has already been done elsewhere */
-	printk_debug("size_kb 0x%x, membytes 0x%x\n", size_kb, membytes);
-	msr.hi = 0x20000000 | membytes>>24;
-	msr.lo = 0x100 | ( ((membytes >>12) & 0xfff) << 20);
-	wrmsr(0x10000028, msr);
-	msr.hi = 0x20000000 | membytes>>24;
-	msr.lo = 0x100 | ( ((membytes >>12) & 0xfff) << 20);
-	wrmsr(0x40000029, msr);
-#endif
-#if 0
-	msr = rdmsr(0x10000028);
-	printk_debug("MSR 0x%x is now 0x%x:0x%x\n", 0x10000028, msr.hi,msr.lo);
-	msr = rdmsr(0x40000029);
-	printk_debug("MSR 0x%x is now 0x%x:0x%x\n", 0x40000029, msr.hi,msr.lo);
-#endif
-#if 1
+
    /* fixme: SMM MSR 0x10000026 and 0x400000023 */
    /* calculate the OFFSET field */
    tmp = membytes - SMM_OFFSET;
@@ -244,38 +236,136 @@
    msr.lo = tmp2;
    wrmsr(0x10000026, msr);
 #endif
-#if 0
-
-	msr.hi = 0x2cfbc040;
-	msr.lo = 0x400fffc0;
-	wrmsr(0x10000026, msr);
-	msr = rdmsr(0x10000026);
-	printk_debug("MSR 0x%x is now 0x%x:0x%x\n", 0x10000026, msr.hi, msr.lo);
-#endif
-#if 0
-	msr.hi = 0x22fffc02;
-	msr.lo = 0x10ffbf00;
-	wrmsr(0x1808, msr);
-	msr = rdmsr(0x1808);
-	printk_debug("MSR 0x%x is now 0x%x:0x%x\n", 0x1808, msr.hi, msr.lo);
-#endif
-#if 0	// SDG - don't do this
-	/* now do the default MSR values */
-	for(i = 0; msr_defaults[i].msr_no; i++) {
-		msr_t msr;
-		wrmsr(msr_defaults[i].msr_no, msr_defaults[i].msr);	// MSR - see table above
-		msr = rdmsr(msr_defaults[i].msr_no);
-		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", msr_defaults[i].msr_no, msr.hi,msr.lo);
-	}
-#endif
 }

static void enable_shadow(device_t dev)
 {
+}
+
+void print_conf(void) {
+	int i;
+	unsigned long iol;
+	msr_t msr;
    
+	int cpu_msr_defs[] =  { L2_CONFIG_MSR, CPU_IM_CONFIG, 
+							CPU_DM_CONFIG0, CPU_DM_CONFIG1, CPU_DM_PFLOCK, CPU_RCONF_DEFAULT,
+							CPU_RCONF_BYPASS, CPU_RCONF_A0_BF, CPU_RCONF_C0_DF, CPU_RCONF_E0_FF,
+							CPU_RCONF_SMM, CPU_RCONF_DMM, GLCP_DELAY_CONTROLS, GL_END
+							};
+
+	int gliu0_msr_defs[] = {MSR_GLIU0_BASE1, MSR_GLIU0_BASE2, MSR_GLIU0_BASE3, MSR_GLIU0_BASE4, MSR_GLIU0_BASE5, MSR_GLIU0_BASE6,
+							 GLIU0_P2D_BMO_0, GLIU0_P2D_BMO_1, MSR_GLIU0_SYSMEM,
+							 GLIU0_P2D_RO_0, GLIU0_P2D_RO_1, GLIU0_P2D_RO_2, MSR_GLIU0_SHADOW,
+							 GLIU0_IOD_BM_0, GLIU0_IOD_BM_1, GLIU0_IOD_BM_2,
+							 GLIU0_IOD_SC_0, GLIU0_IOD_SC_1, GLIU0_IOD_SC_2, GLIU0_IOD_SC_3, GLIU0_IOD_SC_4, GLIU0_IOD_SC_5,
+							 GLIU0_GLD_MSR_COH, GL_END
+							};
+
+	int gliu1_msr_defs[] = {MSR_GLIU1_BASE1, MSR_GLIU1_BASE2, MSR_GLIU1_BASE3, MSR_GLIU1_BASE4, MSR_GLIU1_BASE5, MSR_GLIU1_BASE6,
+							 MSR_GLIU1_BASE7, MSR_GLIU1_BASE8, MSR_GLIU1_BASE9, MSR_GLIU1_BASE10,
+							 GLIU1_P2D_R_0, GLIU1_P2D_R_1, GLIU1_P2D_R_2, GLIU1_P2D_R_3, MSR_GLIU1_SHADOW,
+							 GLIU1_IOD_BM_0, GLIU1_IOD_BM_1, GLIU1_IOD_BM_2,
+							 GLIU1_IOD_SC_0, GLIU1_IOD_SC_1, GLIU1_IOD_SC_2, GLIU1_IOD_SC_3,
+							 GLIU1_GLD_MSR_COH, GL_END
+							};
+
+	int rconf_msr[] = { CPU_RCONF0, CPU_RCONF1, CPU_RCONF2, CPU_RCONF3, CPU_RCONF4,
+						CPU_RCONF5, CPU_RCONF6, CPU_RCONF7, GL_END
+							};
+							
+	int cs5536_msr[] = { MDD_LBAR_GPIO, MDD_LBAR_FLSH0, MDD_LBAR_FLSH1, MDD_LEG_IO, MDD_PIN_OPT,
+						 MDD_IRQM_ZLOW, MDD_IRQM_ZHIGH, MDD_IRQM_PRIM, GL_END
+							};
+							
+	int pci_msr[] = { GLPCI_CTRL, GLPCI_ARB, GLPCI_REN, GLPCI_A0_BF, GLPCI_C0_DF, GLPCI_E0_FF,
+					  GLPCI_RC0, GLPCI_RC1, GLPCI_RC2, GLPCI_RC3, GLPCI_EXT_MSR, GLPCI_SPARE,
+						 GL_END
+							};
+
+	int dma_msr[] =  { MDD_DMA_MAP, MDD_DMA_SHAD1, MDD_DMA_SHAD2, MDD_DMA_SHAD3, MDD_DMA_SHAD4,
+							MDD_DMA_SHAD5, MDD_DMA_SHAD6, MDD_DMA_SHAD7, MDD_DMA_SHAD8,
+							MDD_DMA_SHAD9, GL_END
+							};
+
+
+	printk_debug("---------- CPU ------------\n");
+
+	for(i = 0; cpu_msr_defs[i] != GL_END; i++) {
+		msr = rdmsr(cpu_msr_defs[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cpu_msr_defs[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- GLIU 0 ------------\n");
+
+	for(i = 0; gliu0_msr_defs[i] != GL_END; i++) {
+		msr = rdmsr(gliu0_msr_defs[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", gliu0_msr_defs[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- GLIU 1 ------------\n");
+
+	for(i = 0; gliu1_msr_defs[i] != GL_END; i++) {
+		msr = rdmsr(gliu1_msr_defs[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", gliu1_msr_defs[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- RCONF ------------\n");
+
+	for(i = 0; rconf_msr[i] != GL_END; i++) {
+		msr = rdmsr(rconf_msr[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", rconf_msr[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- VARIA ------------\n");
+	msr = rdmsr(0x51300010);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51300010, msr.hi, msr.lo);
+
+	msr = rdmsr(0x51400015);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51400015, msr.hi, msr.lo);
+
+	printk_debug("---------- DIVIL IRQ ------------\n");
+	msr = rdmsr(MDD_IRQM_YLOW);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YLOW, msr.hi, msr.lo);
+	msr = rdmsr(MDD_IRQM_YHIGH);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YHIGH, msr.hi, msr.lo);
+	msr = rdmsr(MDD_IRQM_ZLOW);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZLOW, msr.hi, msr.lo);
+	msr = rdmsr(MDD_IRQM_ZHIGH);
+	printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZHIGH, msr.hi, msr.lo);
+
+
+	printk_debug("---------- PCI ------------\n");
+
+	for(i = 0; pci_msr[i] != GL_END; i++) {
+		msr = rdmsr(pci_msr[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", pci_msr[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- LPC/UART DMA ------------\n");
+
+	for(i = 0; dma_msr[i] != GL_END; i++) {
+		msr = rdmsr(dma_msr[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", dma_msr[i], msr.hi, msr.lo);
+	}
+
+	printk_debug("---------- CS5536 ------------\n");
+
+	for(i = 0; cs5536_msr[i] != GL_END; i++) {
+		msr = rdmsr(cs5536_msr[i]);
+		printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cs5536_msr[i], msr.hi, msr.lo);
+	}
+	
+	iol = inl(GPIOL_INPUT_ENABLE);
+	printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_INPUT_ENABLE, iol);
+	iol = inl(GPIOL_EVENTS_ENABLE);
+	printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_EVENTS_ENABLE, iol);
+	iol = inl(GPIOL_INPUT_INVERT_ENABLE);
+	printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_INPUT_INVERT_ENABLE, iol);
+	iol = inl(GPIO_MAPPER_X);
+	printk_debug("IOR 0x%08X is now 0x%08X\n", GPIO_MAPPER_X, iol);
+	
 }

-
 static void enable_L2_cache(void) {
    msr_t msr;

@@ -306,19 +396,75 @@
    printk_debug("L2 cache enabled\n");
 }

-
 static void northbridge_init(device_t dev) 
 {
+	//msr_t msr;
    struct northbridge_amd_lx_config *nb = (struct northbridge_amd_lx_config *)dev->chip_info;
-	printk_debug("northbridge: %s()\n", __FUNCTION__);
+
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);
    
    enable_shadow(dev);
-	irq_init_steering(dev, nb->irqmap);
+	/*
+	 * Swiss cheese
+	 */
+	//msr = rdmsr(MSR_GLIU0_SHADOW);
+	
+	//msr.hi |= 0x3;
+	//msr.lo |= 0x30000;
+	
+// not needed (also irq steering is in legacy vsm so it wouldnt work either)
+//	irq_init_steering(dev, nb->irqmap);
+
+	//printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MSR_GLIU0_SHADOW, msr.hi, msr.lo);
+	//printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MSR_GLIU1_SHADOW, msr.hi, msr.lo);
 }

+void northbridge_set_resources(struct device *dev)
+{
+	struct resource *resource, *last;
+	unsigned link;
+	uint8_t line;
+
+	last = &dev->resource[dev->resources];
+
+	for(resource = &dev->resource[0]; resource < last; resource++)
+	{
+
+		// andrei: do not change the base address, it will make the VSA virtual registers unusable
+		//pci_set_resource(dev, resource);
+		// FIXME: static allocation may conflict with dynamic mappings!
+	}
+
+	for(link = 0; link < dev->links; link++) {
+		struct bus *bus;
+		bus = &dev->link[link];
+		if (bus->children) {
+			printk_debug("my_dev_set_resources: assign_resources %d\n", bus);
+			assign_resources(bus);
+		}
+	}
+
+	/* set a default latency timer */
+	pci_write_config8(dev, PCI_LATENCY_TIMER, 0x40);
+
+	/* set a default secondary latency timer */
+	if ((dev->hdr_type & 0x7f) == PCI_HEADER_TYPE_BRIDGE) {
+		pci_write_config8(dev, PCI_SEC_LATENCY_TIMER, 0x40);
+	}
+
+	/* zero the irq settings */
+	line = pci_read_config8(dev, PCI_INTERRUPT_PIN);
+	if (line) {
+		pci_write_config8(dev, PCI_INTERRUPT_LINE, 0);
+	}
+	
+	/* set the cache line size, so far 64 bytes is good for everyone */
+	pci_write_config8(dev, PCI_CACHE_LINE_SIZE, 64 >> 2);
+}
+
 static struct device_operations northbridge_operations = {
    .read_resources   = pci_dev_read_resources,
-	.set_resources    = pci_dev_set_resources,
+	.set_resources    = northbridge_set_resources,
    .enable_resources = pci_dev_enable_resources,
    .init             = northbridge_init,
    .enable           = 0,
@@ -328,17 +474,15 @@
 static struct pci_driver northbridge_driver __pci_driver = {
    .ops = &northbridge_operations,
    .vendor = PCI_VENDOR_ID_AMD,
-	.device = PCI_DEVICE_ID_AMD_LX,
+	.device = PCI_DEVICE_ID_AMD_LXBRIDGE,
 };

-#define BRIDGE_IO_MASK (IORESOURCE_IO | IORESOURCE_MEM)

static void pci_domain_read_resources(device_t dev)
 {
         struct resource *resource;
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);

-	printk_spew("%s:%s()\n", NORTHBRIDGE_FILE, __FUNCTION__);
-
         /* Initialize the system wide io space constraints */
         resource = new_resource(dev, IOINDEX_SUBTRACTIVE(0,0));
         resource->limit = 0xffffUL;
@@ -355,96 +499,64 @@
 {
         struct resource *resource;

-        if (!sizek) {
-                return;
-        }
+	if (!sizek) return;
+	
         resource = new_resource(dev, index);
         resource->base  = ((resource_t)basek) << 10;
         resource->size  = ((resource_t)sizek) << 10;
-        resource->flags =  IORESOURCE_MEM | IORESOURCE_CACHEABLE | \
+	resource->flags =  IORESOURCE_MEM | IORESOURCE_CACHEABLE |
                 IORESOURCE_FIXED | IORESOURCE_STORED | IORESOURCE_ASSIGNED;
 }

-static void tolm_test(void *gp, struct device *dev, struct resource *new)
+static void pci_domain_set_resources(device_t dev)
 {
-	struct resource **best_p = gp;
-	struct resource *best;
-	best = *best_p;
-	if (!best || (best->base > new->base)) {
-		best = new;
+	int idx;
+	device_t mc_dev;
+
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);
+
+	mc_dev = dev->link[0].children;
+	if (mc_dev) 
+	{
+		/* Report the memory regions */
+		idx = 10;
+		ram_resource(dev, idx++, 0, 640);
+		ram_resource(dev, idx++, 1024, ((sizeram() - VIDEO_MB) * 1024) - SMM_SIZE - 1024);
    }
-	*best_p = best;
-}

-#if 0
-static uint32_t find_pci_tolm(struct bus *bus)
-{
-	struct resource *min;
-	uint32_t tolm;
-	min = 0;
-	search_bus_resources(bus, IORESOURCE_MEM, IORESOURCE_MEM, tolm_test, &min);
-	tolm = 0xffffffffUL;
-	if (min && tolm > min->base) {
-		tolm = min->base;
-	}
-	return tolm;
+	assign_resources(&dev->link[0]);
 }
-#endif
-#define FRAMEBUFFERK 4096

-static void pci_domain_set_resources(device_t dev)
+static void pci_domain_enable(device_t dev)
 {
-#if 0
-	device_t mc_dev;
-        uint32_t pci_tolm;
+	struct northbridge_amd_lx_config *nb = (struct northbridge_amd_lx_config *)dev->chip_info;

-        pci_tolm = find_pci_tolm(&dev->link[0]);
-	mc_dev = dev->link[0].children;
-	if (mc_dev) {
-		unsigned int tomk, tolmk;
-		unsigned int ramreg = 0;
-		int i, idx;
-		unsigned int *bcdramtop = (unsigned int *)(GX_BASE + BC_DRAM_TOP);
-		unsigned int *mcgbaseadd = (unsigned int *)(GX_BASE + MC_GBASE_ADD);
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);

-		for(i=0; i<0x20; i+= 0x10) {
-			unsigned int *mcreg = (unsigned int *)(GX_BASE + MC_BANK_CFG);
-			unsigned int mem_config = *mcreg;
+	// do this here for now -- this chip really breaks our device model
+	enable_L2_cache();
+	northbridge_init_early();
+	cpubug();
+	chipsetinit(nb);
+	setup_lx();
+	setup_realmode_idt();

-			if (((mem_config & (DIMM_PG_SZ << i)) >> (4 + i)) == 7)
-				continue;
-			ramreg += 1 << (((mem_config & (DIMM_SZ << i)) >> (i + 8)) + 2);
-		}
-			
-		tomk = ramreg << 10;
+	printk_debug("Before VSA:\n");
+	print_conf();

-		/* Sort out the framebuffer size */
-		tomk -= FRAMEBUFFERK;
-		*bcdramtop = ((tomk << 10) - 1);
-		*mcgbaseadd = (tomk >> 9);
+	do_vsmbios();	// do the magic stuff here, so prepare your tambourine ;)
+	
+	printk_debug("After VSA:\n");
+	print_conf();

-		printk_debug("BC_DRAM_TOP = 0x%08x\n", *bcdramtop);
-		printk_debug("MC_GBASE_ADD = 0x%08x\n", *mcgbaseadd);
-
-		printk_debug("I would set ram size to %d Mbytes\n", (tomk >> 10));
-
-		/* Compute the top of Low memory */
-		tolmk = pci_tolm >> 10;
-		if (tolmk >= tomk) {
-			/* The PCI hole does does not overlap the memory.
-			 */
-			tolmk = tomk;
-		}
-		/* Report the memory regions */
-		idx = 10;
-		ram_resource(dev, idx++, 0, tolmk);
-	}
-#endif
-	assign_resources(&dev->link[0]);
+	graphics_init();
+	pci_set_method(dev);
 }

static unsigned int pci_domain_scan_bus(device_t dev, unsigned int max)
 {
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);
+
         max = pci_scan_bus(&dev->link[0], PCI_DEVFN(0, 0), 0xff, max);
         return max;
 }
@@ -453,12 +565,14 @@
         .read_resources   = pci_domain_read_resources,
         .set_resources    = pci_domain_set_resources,
         .enable_resources = enable_childrens_resources,
-        .init             = 0,
         .scan_bus         = pci_domain_scan_bus,
+        .enable           = pci_domain_enable,
 };

static void cpu_bus_init(device_t dev)
 {
+	printk_spew(">> Entering northbridge.c: %s\n", __FUNCTION__);
+
         initialize_cpus(&dev->link[0]);
 }

@@ -474,38 +588,16 @@
         .scan_bus         = 0,
 };

-void chipsetInit (void);
-
 static void enable_dev(struct device *dev)
 {
-	printk_debug("lx north: enable_dev\n");
-	void northbridgeinit(void);
-	void chipsetinit(struct northbridge_amd_lx_config *nb);
-	void setup_realmode_idt(void);
-	void do_vsmbios(void);
+	printk_spew(">> Entering northbridge.c: %s with path %d\n", 
+		__FUNCTION__, dev->path.type);
+
         /* Set the operations if it is a special bus type */
-        if (dev->path.type == DEVICE_PATH_PCI_DOMAIN) {
-		struct northbridge_amd_lx_config *nb = (struct northbridge_amd_lx_config *)dev->chip_info;
-		extern void cpubug(void);
-		printk_debug("DEVICE_PATH_PCI_DOMAIN\n");
-		/* cpubug MUST be called before setup_lx(), so we force the issue here */
-			enable_L2_cache();
-		northbridgeinit();
-			/* cpubug();	GX3*/
-		chipsetinit(nb);
-		setup_lx();
-		/* do this here for now -- this chip really breaks our device model */
-		setup_realmode_idt();
-		do_vsmbios();
-		graphics_init();
+	if (dev->path.type == DEVICE_PATH_PCI_DOMAIN)
    	dev->ops = &pci_domain_ops;
-		pci_set_method(dev);
-		ram_resource(dev, 0, 0, ((sizeram() - VIDEO_MB) * 1024) - SMM_SIZE);
-        } else if (dev->path.type == DEVICE_PATH_APIC_CLUSTER) {
-		printk_debug("DEVICE_PATH_APIC_CLUSTER\n");
+	else if (dev->path.type == DEVICE_PATH_APIC_CLUSTER)
                 dev->ops = &cpu_bus_ops;
-        }
-	printk_debug("lx north: end enable_dev\n");
 }

struct chip_operations northbridge_amd_lx_ops = {

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.h
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.h	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.h	2006-09-13 21:59:09 UTC (rev 2412)
@@ -2,5 +2,6 @@
 #define NORTHBRIDGE_AMD_LX_H

extern unsigned int lx_scan_root_bus(device_t root, unsigned int max);
+int sizeram(void);

#endif /* NORTHBRIDGE_AMD_LX_H */

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridgeinit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridgeinit.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridgeinit.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -26,7 +26,6 @@
    {.desc_name=MSR_GLIU0_BASE2,  .desc_type= BM,.hi= MSR_MC + 0x0,.lo=(0x80 << 20) + 0x0FFFE0},		/*  80000-9ffff to Mc*/
    {.desc_name=MSR_GLIU0_SHADOW, .desc_type= SC_SHADOW,.hi=  MSR_MC + 0x0,.lo=  0x03},	/*  C0000-Fffff split to MC and PCI (sub decode) A0000-Bffff handled by SoftVideo*/
    {.desc_name=MSR_GLIU0_SYSMEM, .desc_type= R_SYSMEM,.hi=  MSR_MC,.lo=  0x0},		/*  Catch and fix dynamicly.*/
-	{.desc_name=MSR_GLIU0_DMM,    .desc_type= BMO_DMM,.hi=  MSR_MC,.lo=  0x0},		/*  Catch and fix dynamicly.*/
    {.desc_name=MSR_GLIU0_SMM,    .desc_type= BMO_SMM,.hi=  MSR_MC,.lo=  0x0},		/*  Catch and fix dynamicly.*/
    {.desc_name=GLIU0_GLD_MSR_COH,.desc_type= OTHER,.hi= 0x0,.lo= GL0_CPU},
    {.desc_name=GL_END,           .desc_type= GL_END,.hi= 0x0,.lo= 0x0},
@@ -38,10 +37,8 @@
    {.desc_name=MSR_GLIU1_BASE2,.desc_type=  BM,.hi=  MSR_GL0 + 0x0,.lo= (0x80 << 20) +0x0FFFE0},	/*  80000-9ffff to Mc*/
    {.desc_name=MSR_GLIU1_SHADOW,.desc_type=  SC_SHADOW,.hi=  MSR_GL0 + 0x0,.lo=  0x03}, /*  C0000-Fffff split to MC and PCI (sub decode)*/
    {.desc_name=MSR_GLIU1_SYSMEM,.desc_type=  R_SYSMEM,.hi=  MSR_GL0,.lo=  0x0},		/*  Cat0xc and fix dynamicly.*/
-	{.desc_name=MSR_GLIU1_DMM,.desc_type=  BM_DMM,.hi=  MSR_GL0,.lo=  0x0},			/*  Cat0xc and fix dynamicly.*/
    {.desc_name=MSR_GLIU1_SMM,.desc_type=  BM_SMM,.hi=  MSR_GL0,.lo=  0x0},			/*  Cat0xc and fix dynamicly.*/
    {.desc_name=GLIU1_GLD_MSR_COH,.desc_type= OTHER,.hi= 0x0,.lo= GL1_GLIU0},
-	{.desc_name=MSR_GLIU1_FPU_TRAP,.desc_type=  SCIO,.hi=  (GL1_GLCP << 29) + 0x0,.lo=  0x033000F0},	/*  FooGlue FPU 0xF0*/
    {.desc_name=GL_END,.desc_type= GL_END,.hi= 0x0,.lo= 0x0},
 };

@@ -102,9 +99,6 @@
    {0x0FFFFFFFF, 			{0x0FFFFFFFF, 0x0FFFFFFFF}},	/*  END*/
 };

-/* do we have dmi or not? assume NO per AMD */
-int havedmi = 0;
-
 static void
 writeglmsr(struct gliutable *gl){
    msr_t msr;
@@ -112,10 +106,10 @@
    msr.lo = gl->lo;
    msr.hi = gl->hi;
    wrmsr(gl->desc_name, msr);	// MSR - see table above
-	printk_debug("%s: write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo);
+	// printk_debug("%s: write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo); //GX3
    /* they do this, so we do this */
    msr = rdmsr(gl->desc_name);
-	printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo);
+	// printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo); // GX3
 }

static void
@@ -144,97 +138,43 @@

/* 
     * Figure out how much RAM is in the machine and alocate all to the 
-	 * system. We will adjust for SMM and DMM now and Frame Buffer later.
+	 * system. We will adjust for SMM now and Frame Buffer later.
     */
    sizembytes = sizeram();
    printk_debug("%s: enable for %dm bytes\n", __FUNCTION__, sizembytes);
    sizebytes = sizembytes << 20;

-	sizebytes -= SMM_SIZE*1024 +1;
+	sizebytes -= ((SMM_SIZE)<<10);
+	printk_debug("usable RAM: %d bytes\n", sizebytes);

-	if (havedmi)
-		sizebytes -= DMM_SIZE * 1024 + 1;
-
-	sizebytes -= 1;
    msr.hi = (gl->hi & 0xFFFFFF00) | (sizebytes >> 24);
    /* set up sizebytes to fit into msr.lo */
    sizebytes <<= 8; /* what? well, we want bits 23:12 in bits 31:20. */
    sizebytes &= 0xfff00000;
    sizebytes |= 0x100;
    msr.lo = sizebytes;
+
    wrmsr(gl->desc_name, msr);	// MSR - see table above
    msr = rdmsr(gl->desc_name);
-	printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, 
-				gl->desc_name, msr.hi, msr.lo);
-	
+	/* printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, 
+				gl->desc_name, msr.hi, msr.lo); */ // GX3	
 }
-static void
-DMMGL0Init(struct gliutable *gl) {
-	msr_t msr;
-	int sizebytes = sizeram()<<20;
-	long offset;

-	if (! havedmi)
-		return;
-
-	printk_debug("%s: %d bytes\n", __FUNCTION__, sizebytes);
-
-	sizebytes -= DMM_SIZE*1024;
-	offset = sizebytes - DMM_OFFSET;
-	printk_debug("%s: offset is 0x%08x\n", __FUNCTION__, offset);
-	offset >>= 12;
-	msr.hi = (gl->hi) | (offset << 8);
-	/* I don't think this is needed */
-	msr.hi &= 0xffffff00;
-	msr.hi |= (DMM_OFFSET >> 24);
-	msr.lo = DMM_OFFSET << 8;
-	msr.lo |= ((~(DMM_SIZE*1024)+1)>>12)&0xfffff;
-	
-	wrmsr(gl->desc_name, msr);	// MSR - See table above
-	msr = rdmsr(gl->desc_name);
-	printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo);
-	
-}
 static void
-DMMGL1Init(struct gliutable *gl) {
-	msr_t msr;
-
-	if (! havedmi)
-		return;
-
-	printk_debug("%s:\n", __FUNCTION__ );
-
-	msr.hi = gl->hi;
-	/* I don't think this is needed */
-	msr.hi &= 0xffffff00;
-	msr.hi |= (DMM_OFFSET >> 24);
-	msr.lo = DMM_OFFSET << 8;
-	/* hmm. AMD source has SMM here ... SMM, not DMM? We think DMM */
-	printk_err("%s: warning, using DMM_SIZE even though AMD used SMM_SIZE\n", __FUNCTION__);
-	msr.lo |= ((~(DMM_SIZE*1024)+1)>>12)&0xfffff;
-	
-	wrmsr(gl->desc_name, msr);	// MSR - See table above
-	msr = rdmsr(gl->desc_name);
-	printk_debug("%s: AFTER write msr 0x%08x, val 0x%08x:0x%08x\n", __FUNCTION__, gl->desc_name, msr.hi, msr.lo);
-}
-static void
 SMMGL0Init(struct gliutable *gl) {
    msr_t msr;
    int sizebytes = sizeram()<<20;
    long offset;

-	sizebytes -= SMM_SIZE*1024;
+	sizebytes -= ((SMM_SIZE)<<10);

-	if (havedmi)
-		sizebytes -= DMM_SIZE * 1024;
-
    printk_debug("%s: %d bytes\n", __FUNCTION__, sizebytes);

offset = sizebytes - SMM_OFFSET;
+	offset = (offset >> 12) & 0x000fffff;
    printk_debug("%s: offset is 0x%08x\n", __FUNCTION__, offset);
-	offset >>= 12;

-	msr.hi = offset << 8;
+	msr.hi = offset << 8 | MSR_MC;
    msr.hi |= SMM_OFFSET>>24;

msr.lo = SMM_OFFSET << 8;
@@ -277,14 +217,6 @@
    		SysmemInit(gl);
    		break;
    
-		case BMO_DMM: /*  check for a DMM entry*/
-			DMMGL0Init(gl);
-			break;
-	
-		case BM_DMM	: /*  check for a DMM entry*/
-			DMMGL1Init(gl);
-			break;
-	
    	case BMO_SMM	: /*  check for a SMM entry*/
    		SMMGL0Init(gl);
    		break;
@@ -317,7 +249,8 @@
    struct gliutable *gl = 0;
    int i;
    msr_t msr;
-	int msrnum;
+	int msrnum, enable_preempt, enable_cpu_override;
+	int nic_grants_control, enable_bus_parking;

/* */
    /*  R0 - GLPCI settings for Conventional Memory space.*/
@@ -415,13 +348,21 @@
    /* */
    /* 5535 NB Init*/
    /* */	
+
+	/* Arbiter setup */
+
+	enable_preempt = GLPCI_ARB_LOWER_PRE0_SET | GLPCI_ARB_LOWER_PRE1_SET | GLPCI_ARB_LOWER_PRE2_SET | GLPCI_ARB_LOWER_CPRE_SET; 
+	enable_cpu_override = GLPCI_ARB_LOWER_COV_SET;
+	enable_bus_parking = GLPCI_ARB_LOWER_PARK_SET;
+	nic_grants_control = (0x4 << GLPCI_ARB_UPPER_R2_SHIFT) | (0x3 << GLPCI_ARB_UPPER_H2_SHIFT );
+
    msrnum = GLPCI_ARB;
    msr = rdmsr(msrnum);
-	msr.hi |=  GLPCI_ARB_UPPER_PRE0_SET | GLPCI_ARB_UPPER_PRE1_SET;
-	msr.lo |=  GLPCI_ARB_LOWER_IIE_SET;
+
+	msr.hi |=  nic_grants_control;
+	msr.lo |=  enable_cpu_override  | enable_preempt | enable_bus_parking;
    wrmsr(msrnum, msr);

-
    msrnum = GLPCI_CTRL;
    msr = rdmsr(msrnum);

@@ -507,11 +448,11 @@

for(i = 0; gating->msrnum != 0xffffffff; i++) {
    	msr = rdmsr(gating->msrnum);
-		printk_debug("%s: MSR 0x%08x is 0x%08x:0x%08x\n", __FUNCTION__, gating->msrnum, msr.hi, msr.lo);
+		//printk_debug("%s: MSR 0x%08x is 0x%08x:0x%08x\n", __FUNCTION__, gating->msrnum, msr.hi, msr.lo); //GX3 
    	msr.hi |= gating->msr.hi;
    	msr.lo |= gating->msr.lo;
-		printk_debug("%s: MSR 0x%08x will be set to  0x%08x:0x%08x\n", __FUNCTION__, 
-			gating->msrnum, msr.hi, msr.lo);
+		/* printk_debug("%s: MSR 0x%08x will be set to  0x%08x:0x%08x\n", __FUNCTION__, 
+			gating->msrnum, msr.hi, msr.lo); */ // GX3
    	wrmsr(gating->msrnum, msr);	// MSR - See the table above
    	gating +=1;
    }
@@ -526,12 +467,12 @@

for(i = 0; prio->msrnum != 0xffffffff; i++) {
    	msr = rdmsr(prio->msrnum);
-		printk_debug("%s: MSR 0x%08x is 0x%08x:0x%08x\n", __FUNCTION__, prio->msrnum, msr.hi, msr.lo);
+		// printk_debug("%s: MSR 0x%08x is 0x%08x:0x%08x\n", __FUNCTION__, prio->msrnum, msr.hi, msr.lo); // GX3
    	msr.hi |= prio->msr.hi;
    	msr.lo &= ~0xfff;
    	msr.lo |= prio->msr.lo;
-		printk_debug("%s: MSR 0x%08x will be set to 0x%08x:0x%08x\n", __FUNCTION__, 
-			prio->msrnum, msr.hi, msr.lo);
+		/* printk_debug("%s: MSR 0x%08x will be set to 0x%08x:0x%08x\n", __FUNCTION__, 
+			prio->msrnum, msr.hi, msr.lo);  */ // GX3
    	wrmsr(prio->msrnum, msr);	// MSR - See the table above
    	prio +=1;
    }
@@ -563,7 +504,7 @@
    // ok this is whacky bit translation time.
    int bit;
    uint8_t shadowByte;
-	msr_t msr;
+	msr_t msr = {0, 0};
    shadowByte = (uint8_t) (shadowLo >> 16);

// load up D000 settings in edx.
@@ -674,6 +615,7 @@
    uint64_t shadowSettings = getShadow();
    shadowSettings &= (uint64_t) 0xFFFF00000000FFFFULL;	// Disable read & writes
    shadowSettings |= (uint64_t) 0x00000000F0000000ULL;	// Enable reads for F0000-FFFFF
+	shadowSettings |= (uint64_t) 0x0000FFFFFFFF0000ULL;	// Enable rw for C0000-CFFFF
    setShadow(shadowSettings);
 }

@@ -704,7 +646,7 @@
    int i;
    msr_t msr;
    uint8_t SysMemCacheProp;
-	uint8_t RegionProp;
+	//uint8_t RegionProp;

/* Locate SYSMEM entry in GLIU0table */
    for(i = 0; gliu0table[i].desc_name != GL_END; i++) {
@@ -722,6 +664,8 @@
    /* found the descriptor... get its contents */
    msr = rdmsr(gl->desc_name);

+	printk_debug("SYSDESC: 0x%08X:0x%08X\n",msr.hi,msr.lo);
+
    /* 20 bit address -  The bottom 12 bits go into bits 20-31 in eax, the 
     * top 8 bits go into 0-7 of edx. 
     */
@@ -729,6 +673,8 @@
    msr.lo = ((msr.lo << 12) | (msr.lo >> 20)) & 0x000FFFFF;
    msr.lo <<= RCONF_DEFAULT_LOWER_SYSTOP_SHIFT;	// 8
    
+	printk_debug("RCONF LO: 0x%08X\n",msr.lo);
+	
    // Set Default SYSMEM region properties
    msr.lo &= ~SYSMEM_RCONF_WRITETHROUGH;	// 8 (or ~8)

@@ -752,13 +698,14 @@
    msr = rdmsr(CPU_RCONF_BYPASS);
    msr.lo = (msr.lo & 0xFFFF0000) | (SysMemCacheProp << 8) | SysMemCacheProp;
    wrmsr(CPU_RCONF_BYPASS, msr);
+	
+	printk_debug("CPU_RCONF_SMM (180E)  0x%08x : 0x%08x\n", msr.hi, msr.lo);
 }

-/* ***************************************************************************/
+/****************************************************************************/
+/* *	northbridge_init_early */
 /* **/
-/* *	northBridgeInit*/
-/* **/
 /* *	Core Logic initialization:  Host bridge*/
 /* **/
 /* *	Entry:*/
@@ -767,8 +714,7 @@
 /* **/
 /* ***************************************************************************/

-void
-northbridgeinit(void)
+void northbridge_init_early(void)
 {
    msr_t msr;
    int i;
@@ -791,6 +737,8 @@
    // makes sure all INVD instructions are treated as WBINVD.  We do this
    // because we've found some programs which require this behavior.
    // That subset of cacheInit() is implemented here:
+	
+	/* GX3 OK */
    msr = rdmsr(CPU_DM_CONFIG0);
    msr.lo |= DM_CONFIG0_LOWER_WBINVD_SET;
    wrmsr(CPU_DM_CONFIG0, msr);

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/pll_reset.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/pll_reset.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/pll_reset.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -6,7 +6,7 @@

msrGlcpSysRstpll = rdmsr(GLCP_SYS_RSTPLL);
    
-        print_debug("MSR GLCP_SYS_RSTPLL (");
+	print_debug("_MSR GLCP_SYS_RSTPLL (");
    	print_debug_hex32(GLCP_SYS_RSTPLL);
    	print_debug(") value is: ");
    	print_debug_hex32(msrGlcpSysRstpll.hi);
@@ -19,60 +19,18 @@
    // If the "we've already been here" flag is set, don't reconfigure the pll
         if ( !(msrGlcpSysRstpll.lo) )
    { // we haven't configured the PLL; do it now
+	    print_debug("CONFIGURING PLL");
+	
                 POST_CODE(0x77);
    
-               /*
-                *    64 - 32 	    |  31-0 
-                * 
-                *      (03FB)
-                * 0000 0011 1111 1011 | 1000 0000 1101 1110 0000 0000 1000 0001
-                * 
-                *      (039C)
-                * 0000 0011 1001 1100 | 1000 0000 1101 1110 0000 0000 1000 0001
-                * 
-                *       (029C)
-                * 0000 0010 1001 1100 | 1000 0000 1101 1110 0000 0000 1000 0001
-                * 
-                *       (02CB)
-                * 0000 0010 1100 1011 | 1000 0000 1101 1110 0000 0000 1000 0001
-                * 
-                * 00101		1			00101 		1 		| 100000	0		0		11011110 	0000 0000 1000 0001
-                * GLIUMULT	GLIUDIV		COREMULT	COREDIV	| SWFLAGS	(RO)	(RO)	HOLD_COUNT	
-                */
+		// HARDCODED VALUES MOVED BACK TO auto.c AS THEY HAVE TO BE BOARD-SPECIFIC
+		// (this file is included from there)

-                /* ### 02CB  ###
-                 * GLIUMULT = 6
-                 * GLIUDIV = 2
-                 * COREMULT = 6
-                 * COREDIV = 2
-                 * 
-                 * ### 03FB  ###
-                 * GLIUMULT = 8
-                 * GLIUDIV = 2
-                 * COREMULT = 30
-                 * COREDIV = 2
-                 * 
-                 * ### 039C  ###  bad... why?
-                 * GLIUMULT = 8
-                 * GLIUDIV = 0
-                 * COREMULT = 15
-                 * COREDIV = 0
-                 * 
-                 * ### 029C  ###  good...
-                 * GLIUMULT = 6
-                 * GLIUDIV = 0
-                 * COREMULT = 15
-                 * COREDIV = 0
-                 * 
-                 *  CLOCK = 33 MHz
-                 *
-                 */
-
    		/* CPU and GLIU mult/div (GLMC_CLK = GLIU_CLK / 2)  */
-			msrGlcpSysRstpll.hi = 0x0000029C;
+		msrGlcpSysRstpll.hi = PLLMSRhi;

/* Hold Count - how long we will sit in reset */
-			msrGlcpSysRstpll.lo = 0x00DE0000;
+		msrGlcpSysRstpll.lo = PLLMSRlo;

/* Use SWFLAGS to remember: "we've already been here"  */
    		msrGlcpSysRstpll.lo |= 0x80000000;

Modified: trunk/LinuxBIOSv2/src/northbridge/amd/lx/raminit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/lx/raminit.c	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/lx/raminit.c	2006-09-13 21:59:09 UTC (rev 2412)
@@ -18,28 +18,10 @@
    	 *   — MSR 20000019h
    	 */
    	
-   		// This is done by sdram_set_spd_registers()
-		/*WR_MSR   MC_CF07_DATA,   DIMMCONFIG, 0x05000040
+   	// This is done by sdram_set_spd_registers() that is called by sdram/generic_sdram.c just before this
+   	// sdram_set_spd_registers is responsible for reading ram settings from spd rom and configuring sdram conrtoller
+   	// Here follows generic sdram initialization procedure.

-		;WR_MSR	MC_CF07_DATA,   DIMMCONFIG, 0x00000040		; MSR 20000018h except REF_INT bits [23:8]. REF_STAG value from DOCS*/
-		
-	/*
-	 * 0x18000100 : 0x696332A3
-	 * 
-	 * 		63 - 32 | 31                  15                0
-	 * xxxxxxx		| 0110 1001 0110 0011 0011 0010 1010 0011
-	 * 
-	 *  30:28 CAS latency
-	 * 
-	 * 010 - 2.0
-	 * 110 - 2.5
-	 *
-	 */
-
-	msr.hi = 0x18000100;
-	msr.lo = 0x696332A3;
-	wrmsr(MC_CF8F_DATA, msr);
-
    /* 2)  Initialize the following GLMC registers:
     *	— MSR 2000001Ah[15:8] = C8h
     *	— MSR 20002004h[2] = 0, [0] = 1
@@ -48,6 +30,7 @@
    msr.lo = 0x130AD101;
    wrmsr(MC_CF1017_DATA, msr);

+	//ok
    msr.hi = 0x00000000;
    msr.lo = 0x00000001;
    wrmsr(MC_GLD_MSR_PM, msr);
@@ -55,41 +38,37 @@
    /* 3) Release MASK_CKE[1:0] (MSR 2000001Dh[9:8] = 11) */

msr.hi = 0x00000000;
-	msr.lo = 0x00001000;
+	msr.lo = 0x00000000;
    wrmsr(MC_CFCLK_DBUG, msr);
    
-	//print_debug("sdram_enable step 3\r\n");
+	// reset memory controller
+	msr = rdmsr(MC_CF07_DATA);
+	msr.lo |=  0x00000002;
+	wrmsr(MC_CF07_DATA, msr);
+	msr.lo &= 0xFFFFFFFD;
+	wrmsr(MC_CF07_DATA, msr);

/* 4. set and clear REF_TST 16 times, more shouldn't hurt
     * why this is before EMRS and MRS ? */
     
    for (i = 0; i < 19; i++) {
    	msr = rdmsr(MC_CF07_DATA);
-		msr.lo |=  (0x01 << 3);
+		msr.lo |=  0x00000008;
    	wrmsr(MC_CF07_DATA, msr);
-		msr.lo &= ~(0x01 << 3);
+		msr.lo &= 0xFFFFFFF7;
    	wrmsr(MC_CF07_DATA, msr);
    }

/* 5) Initialize REF_INT (MSR 20000018h[23:8]) to set refresh interval.	*/
-	msr.lo |= 0x2B00;
+	msr.lo |= 0x3A00;
    wrmsr(MC_CF07_DATA, msr);

-
-
-	/* set refresh staggering to 4 SDRAM clocks */
-	msr = rdmsr(0x20000018);
-	msr.lo &= ~(0x03 << 6);
-	msr.lo |=  (0x00 << 6);
-	wrmsr(0x20000018, msr);
-	//print_debug("sdram_enable step 5\r\n");
-
-
    /* 6) Perform load-mode with MSR_BA = 01 (MSR 200000018h[29:28] = 01) 
     * to initialize DIMM Extended Mode register. 
     * Load-mode is performed by setting/clearing PROG_DRAM (MSR 200000018h[0]).
     */
+// eeldus et bit29 = 0, mida ta praegu ka on
    msr.lo |=  ((0x01 << 28) | 0x01);
    wrmsr(MC_CF07_DATA, msr);

@@ -100,13 +79,20 @@
    /* 7. Reset DLL, Bit 27 is undocumented in GX datasheet,
     * it is documented in LX datasheet  */	
    /* load Mode Register by set and clear PROG_DRAM */
+// eeldus et bit27:28=00, mida nad ka on
    msr = rdmsr(MC_CF07_DATA);
    msr.lo |=  ((0x01 << 27) | 0x01);
    wrmsr(MC_CF07_DATA, msr);
    msr.lo &= ~((0x01 << 27) | 0x01);
    wrmsr(MC_CF07_DATA, msr);
-	//print_debug("sdram_enable step 7\r\n");

+	//Delay
+	i=inb(0x61);
+	while (i==inb(0x61));
+	i=inb(0x61);
+	while (i==inb(0x61));
+	i=inb(0x61);
+	while (i==inb(0x61));

/* 8. load Mode Register by set and clear PROG_DRAM */
    msr = rdmsr(MC_CF07_DATA);
@@ -114,25 +100,11 @@
    wrmsr(MC_CF07_DATA, msr);
    msr.lo &= ~0x01;
    wrmsr(MC_CF07_DATA, msr);
-	//print_debug("sdram_enable step 8\r\n");

/* wait 200 SDCLKs */
    for (i = 0; i < 200; i++)
    	outb(0xaa, 0x80);

-	/* load RDSYNC */
-	/*msr = rdmsr(0x2000001f);
-	msr.hi = 0x000ff310;
-	msr.lo = 0x00000000;
-	wrmsr(0x2000001f, msr);*/
-
-	/* set delay control */
-	msr = rdmsr(0x4c00000f);
-	msr.hi = 0x830d415a;
-	msr.lo = 0x8ea0ad6a;
-	wrmsr(0x4c00000f, msr);
-
-
    print_debug("DRAM controller init done.\r\n");

/* Fixes from Jordan Crouse of AMD. */

Modified: trunk/LinuxBIOSv2/targets/artecgroup/dbe61/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/targets/artecgroup/dbe61/Config.lb	2006-09-13 21:25:20 UTC (rev 2411)
+++ trunk/LinuxBIOSv2/targets/artecgroup/dbe61/Config.lb	2006-09-13 21:59:09 UTC (rev 2412)
@@ -3,18 +3,25 @@
 target dbe61
 mainboard artecgroup/dbe61

-# leave 64k for vsa
 option CONFIG_COMPRESSED_ROM_STREAM=0
-option ROM_SIZE=1024*256-64*1024
-option FALLBACK_SIZE=ROM_SIZE

+## ROM_SIZE is the total number of bytes allocated for LinuxBIOS use
+## (normal AND fallback images and payloads).
+## leave 64k for vsa and 32K for video ROM
+option ROM_SIZE = 1024*256 - 64*1024 - 32 * 1024
+
+## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a LinuxBIOS image,
+## not including any payload.
+option ROM_IMAGE_SIZE=64*1024
+
+option FALLBACK_SIZE = ROM_SIZE
+
 option DEFAULT_CONSOLE_LOGLEVEL = 11
 option MAXIMUM_CONSOLE_LOGLEVEL = 11
 romimage "fallback" 
    option USE_FALLBACK_IMAGE=1
-	option ROM_IMAGE_SIZE=32*1024
    option LINUXBIOS_EXTRA_VERSION=".0Fallback"
-	payload /tmp/rtl8139--filo.zelf
+	payload /tmp/filo.elf
 end

buildrom ./linuxbios.rom ROM_SIZE  "fallback"

[LinuxBIOS] r2412 - in trunk/LinuxBIOSv2: src/cpu/amd/model_lx src/include/cpu/amd src/northbridge/amd/lx targets/artecgroup/dbe61

[Indrek Kruusa]

[e-mail] wrote:
> Author: rminnich
> Date: 2006-09-13 23:59:09 +0200 (Wed, 13 Sep 2006)
> New Revision: 2412
>
> Modified:
>    trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cpubug.c
>    trunk/LinuxBIOSv2/src/cpu/amd/model_lx/model_lx_init.c
>    trunk/LinuxBIOSv2/src/cpu/amd/model_lx/vsmsetup.c
>    trunk/LinuxBIOSv2/src/include/cpu/amd/lxdef.h
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/chipsetinit.c
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/grphinit.c
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.c
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridge.h
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/northbridgeinit.c
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/pll_reset.c
>    trunk/LinuxBIOSv2/src/northbridge/amd/lx/raminit.c
>    trunk/LinuxBIOSv2/targets/artecgroup/dbe61/Config.lb
> Log:
> changes for the lx and artecgroup mobo
> Signed-off-by: Indrek Kruusa
> Approved-by: Ronald G. Minnich

Signed-off-by: Andrei Birjukov 
Signed-off-by: Anti Sullin

thanks,
Indrek