Re: Etherboot boot problem after jumping to boot code it restarts

Hi,

Thanks for the suggestion.
I just tried the suggestion as well with the poll-ide patch.
Did not work with that well, there is something
else which is missing.
The etherboot payload code is not executed at all it seems..
Any idea why. Please let me know.

Here is the extract of the log I tried , the address have
changed a bit..

****

   203:init_bytes() - zkernel_start:0xfffc0000  zkernel_mask:0x0000007f
Searching for 16 byte tags
    64:rom_read_bytes() - overflowed source buffer. max_block = 3
init_bytes found 0 tags
Initialized controller...
Read completed...
scanning elf header...
Found ELF candiate at offset 0
scan complete...
header_offset is 0
calling elf load...
New segment addr 0x400000 size 0xc240 offset 0x60 filesize 0x7669
(cleaned up) New segment addr 0x400000 size 0xc240 offset 0x60 filesize 0x7669
Loading Segment: addr: 0x0000000000400000 memsz: 0x000000000000c240 filesz: 0x00
00000000007669
Clearing Segment: addr: 0x0000000000407669 memsz: 0x0000000000004bd7
Jumping to boot code at 0x400000


LinuxBIOS-1.0.0 Thu May 1 10:17:27 IST 2003 starting...
Ram1
Ram2
Ram3
Ram Enable 1
*********

Regards
Deepak




[e-mail] wrote
etherboot-5.0.9 is NOT supposed to work. you want etherboot-5.0.6
probably and the patch against it at http://www.missl.cs.umd.edu/~agnew/

On Thu, 1 May 2003 [e-mail] wrote:
> Hi,
>
> I have tried etherboot on my machine which has
> Compact Flash IDE and FLASHROMS(256K/512K). Not
> successful..
> The payload I got was from etherboot-5.0.9, which is
> rtl8139.ebi which is my ethernet chip.
>
> Did an Compact flash..
> fdisk /dev/hdc, created 2 partions hdc1 and hdc2, both
> of ext3 type.
> Then dd if=elfImage_of_kernel of=/dev/hdc bs=4096 skip=1
>
> Set these parameters in my config file.
> option RAMTEST=1
> option USE_GENERIC_ROM=1
> option USE_ELF_BOOT=1
> option ROM_SIZE=524288
> option STD_FLASH=1
>
> #payload ../elfImage.9load
> payload ../rtl8139.ebi
> option PAYLOAD_SIZE=196608
>
> burned the romimage using the uniflash tool.
>
> It seems to have found the elfimage, but just restarts all over
> again, could someone please spot what could be
> the problem and the solution to it.
> Any help on this would really nice. Please find the log
> below.
>
> **********Error Log start****
> LinuxBIOS-1.0.0 Thu May 1 04:29:36 IST 2003 starting...
> Ram1
> Ram2
> Ram3
> Ram Enable 1
> Ram Enable 2
> Ram Enable 3
> Ram Enable 4
> Ram Enable 5
> Ram4
> Ram5
> Ram6
> Copying LinuxBIOS to ram.
> Jumping to LinuxBIOS.
> LinuxBIOS-1.0.0 Thu May 1 04:29:36 IST 2003 booting...
> Finding PCI configuration type.
> PCI: Using configuration type 1
> handle_superio start, nsuperio 1
> handle_superio Pass 0, check #0, s 00009680 s->super 0000a97c
> handle_superio: Pass 0, Superio w83627hf
> handle_superio  port 0x0, defaultport 0x2e
> handle_superio  Using port 0x2e
> handle_superio Pass 0, done #0
> handle_superio done
> Scanning PCI bus...PCI: pci_scan_bus for bus 0
> PCI: 00:00.0 [8086/7124]
> PCI: 00:1e.0 [8086/2418]
> PCI: 00:1f.0 [8086/2410]
> PCI: 00:1f.1 [8086/2411]
> PCI: 00:1f.2 [8086/2412]
> PCI: 00:1f.3 [8086/2413]
> PCI: 00:1f.5 [8086/2415]
> PCI: 00:1f.6 [8086/2416]
> PCI: pci_scan_bus for bus 1
> PCI: 01:04.0 [10ec/8139]
> PCI: 01:05.0 [10ec/8139]
> PCI: pci_scan_bus returning with max=01
> PCI: pci_scan_bus returning with max=01
> done
> Allocating PCI resources...
> ASSIGN RESOURCES, bus 0
> PCI: 00:1e.0 1c <- [0x00001000 - 0x00001fff] bus 1 io
> PCI: 00:1e.0 24 <- [0xfec00000 - 0xfebfffff] bus 1 prefmem
> PCI: 00:1e.0 20 <- [0xfeb00000 - 0xfebfffff] bus 1 mem
> ASSIGN RESOURCES, bus 1
> PCI: 01:04.0 10 <- [0x00001000 - 0x000010ff] io
> PCI: 01:04.0 14 <- [0xfeb00000 - 0xfeb000ff] mem
> PCI: 01:05.0 10 <- [0x00001400 - 0x000014ff] io
> PCI: 01:05.0 14 <- [0xfeb01000 - 0xfeb010ff] mem
> ASSIGNED RESOURCES, bus 1
> PCI: 00:1f.1 20 <- [0x000028e0 - 0x000028ef] io
> PCI: 00:1f.2 20 <- [0x000028c0 - 0x000028df] io
> PCI: 00:1f.3 20 <- [0x000028f0 - 0x000028ff] io
> PCI: 00:1f.5 10 <- [0x00002000 - 0x000020ff] io
> PCI: 00:1f.5 14 <- [0x00002880 - 0x000028bf] io
> PCI: 00:1f.6 10 <- [0x00002400 - 0x000024ff] io
> PCI: 00:1f.6 14 <- [0x00002800 - 0x0000287f] io
> ASSIGNED RESOURCES, bus 0
> done.
> Enabling PCI resourcess...PCI: 00:00.0 cmd <- 06
> PCI: 00:1e.0 cmd <- 07
> PCI: 00:1f.0 cmd <- 0f
> PCI: 00:1f.1 cmd <- 01
> PCI: 00:1f.2 cmd <- 01
> PCI: 00:1f.3 cmd <- 01
> PCI: 00:1f.5 cmd <- 01
> PCI: 00:1f.6 cmd <- 01
> PCI: 01:04.0 cmd <- 03
> PCI: 01:05.0 cmd <- 03
> done.
> Initializing PCI devices...
> PCI devices initialized
> DRP0 = 0x9
> DIMM0 - size = 64M
> DIMM1 - size = 0M
> DRP1 = 0x0
> DIMM2 - size = 0M
> totalram: 64M
> Initializing CPU #0
> Updating microcode
> microcode_info: sig = 0x00000678 pf=0x00000001 rev = 0x00000000
> Enabling cache...
> Setting fixed MTRRs(0-88) type: UC
> Setting fixed MTRRs(0-16) type: WB
> DONE fixed MTRRs
> Setting variable MTRR 0, base:    0MB, range:   64MB, type WB
> DONE variable MTRRs
> Clear out the extra MTRR's
> call intel_enable_fixed_mtrr()
> call intel_enable_var_mtrr()
> Leave setup_mtrrs
> done.
>
> Max cpuid index    : 1
> Vendor ID          : CentaurHauls
> Processor Type     : 0x00
> Processor Family   : 0x06
> Processor Model    : 0x07
> Processor Mask     : 0x00
> Processor Stepping : 0x08
> Feature flags      : 0x00803035
>
> MTRR check
> Fixed MTRRs   : Enabled
> Variable MTRRs: Enabled
>
> Configuring L2 cache...Not 'GenuineIntel' Processor
> Enable Cache
> done.
> Disabling local apic...done.
> CPU #0 Initialized
> ioapic southbridge enabled 180
> RTC Init
> Invalid CMOS LB checksum
> set power on after power fail
> Please turn on nvram
> handle_superio start, nsuperio 1
> handle_superio Pass 1, check #0, s 00009680 s->super 0000a97c
> handle_superio: Pass 1, Superio w83627hf
> handle_superio  port 0x2e, defaultport 0x2e
> handle_superio  Using port 0x2e
>   Call init
> Enabling com device: 03
>   iobase = 0x02f8  irq=3
> handle_superio Pass 1, done #0
> handle_superio done
> handle_superio start, nsuperio 1
> handle_superio Pass 2, check #0, s 00009680 s->super 0000a97c
> handle_superio: Pass 2, Superio w83627hf
> handle_superio  port 0x2e, defaultport 0x2e
> handle_superio  Using port 0x2e
> handle_superio Pass 2, done #0
> handle_superio done
> Wrote linuxbios table at: 00000500 - 00000648  checksum 268b
>
> Welcome to elfboot, the open sourced starter.
> January 2002, Eric Biederman.
> Version 1.2
>
> 203:init_bytes() - zkernel_start:0xfffc0000  zkernel_mask:0x0000007f
> Searching for 16 byte tags
>     64:rom_read_bytes() - overflowed source buffer. max_block = 3
> init_bytes found 0 tags
> Initialized controller...
> Read completed...
> scanning elf header...
> Found ELF candiate at offset 0
> scan complete...
> header_offset is 0
> calling elf load...
> New segment addr 0x94000 size 0x8128 offset 0x60 filesize 0x38d4
> (cleaned up) New segment addr 0x94000 size 0x8128 offset 0x60 filesize 0x38d4
> Loading Segment: addr: 0x0000000000094000 memsz: 0x0000000000008128 filesz: 0x00
> 000000000038d4
> Clearing Segment: addr: 0x00000000000978d4 memsz: 0x0000000000004854
> Jumping to boot code at 0x94000
>
> LinuxBIOS-1.0.0 Thu May 1 04:29:36 IST 2003 starting...
> Ram1
> Ram2
> ....
> **********Error Log end****
>
> Thanks and Regards
>
> _______________________________________________
> Linuxbios mailing list
> [e-mail]
> http://www.clustermatic.org/mailman/listinfo/linuxbios