[LinuxBIOS] [PATCH] add support the IEI PCISA-LX

[Nikolay Petukhov]

This board (http://www.ieiworld.com/en/product_IPC.asp?model=PCISA-LX)
is based on amd-lx800/cs5536, so most of the on-board hardware is work
normally.

Signed-off-by: Nikolay Petukhov

[Uwe Hermann]

On Mon, Nov 26, 2007 at 12:25:45PM +0500, Nikolay Petukhov wrote:
> This board (http://www.ieiworld.com/en/product_IPC.asp?model=PCISA-LX)
> is based on amd-lx800/cs5536, so most of the on-board hardware is work
> normally.

Thanks a lot! Here's a quick review:

I think the full name for this specific board is "PCISA-LX-R11",
correct? If so, please use that everywhere (directory names, strings,
variable names, comments). "PCISA-LX" seems to be the general name for a
whole family of boards.

So the directory name should probably be 'pcisa-lx-r11'.
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c	2007-11-26 09:50:43.000000000 +0500
> @@ -0,0 +1,138 @@
> +/*
> This file is part of the LinuxBIOS project.
> Copyright (C) 2007 Nikolay Petukhov
> Borrowed from amd/db800.

Either the code you grabbed from the DB800 target is trivial (then drop
this line completely), or it is not (then retain the Copyright lines from
the respective DB800 file please).

In this case the file is a plain copy of the DB800 one, with small fixes
in the #defines at the beginning, so please keep the original
copyright/license header and drop the "Borrowed from amd/db800".
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> GNU General Public License for more details.
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> */
>
> +#define ASSEMBLY 1
>
> +#include <stdint.h>
> +#include <device/pci_def.h>
> +#include <arch/io.h>
> +#include <device/pnp_def.h>
> +#include <arch/hlt.h>
> +#include "pc80/serial.c"
> +#include "arch/i386/lib/console.c"
> +#include "ram/ramtest.c"
> +#include "cpu/x86/bist.h"
> +#include "cpu/x86/msr.h"
> +#include <cpu/amd/lxdef.h>
> +#include <cpu/amd/geode_post_code.h>
> +#include "southbridge/amd/cs5536/cs5536.h"
>
> +#define POST_CODE(x) outb(x, 0x80)
> +#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
>
> +#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
> +#include "southbridge/amd/cs5536/cs5536_early_setup.c"
> +#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
>
> +static inline int spd_read_byte(unsigned int device, unsigned int address)
> +{
> return smbus_read_byte(device, address);
>
> +}
>
> +#define ManualConf 1		/* Do automatic strapped PLL config */
> +#define PLLMSRhi 0x0000059C /* CPU and GLIU mult/div 500/400*/
> +#define PLLMSRhi 0x0000049C /* CPU and GLIU mult/div 500/333*/
> +#define PLLMSRhi 0x0000039C /* CPU and GLIU mult/div 500/266*/
> +//0x0000059C 0000 0000 0000 0000 0000 |0101 1|0|01 110|0
> +/* Hold Count - how long we will sit in reset */
> +#define PLLMSRlo 0x00DE6000
>
> +#define DIMM0 0xA0
> +#define DIMM1 0xA2
> +#include "northbridge/amd/lx/raminit.h"
> +#include "northbridge/amd/lx/pll_reset.c"
> +#include "northbridge/amd/lx/raminit.c"
> +#include "sdram/generic_sdram.c"
> +#include "cpu/amd/model_lx/cpureginit.c"
> +#include "cpu/amd/model_lx/syspreinit.c"
>
> +static void msr_init(void)
> +{
> msr_t msr;
> /* Setup access to the cache for under 1MB. */
> msr.hi = 0x24fffc02;
> msr.lo = 0x1000A000;	/* 0-A0000 write back */
> wrmsr(CPU_RCONF_DEFAULT, msr);
> msr.hi = 0x0;		/* Write back */
> msr.lo = 0x0;
> wrmsr(CPU_RCONF_A0_BF, msr);
> wrmsr(CPU_RCONF_C0_DF, msr);
> wrmsr(CPU_RCONF_E0_FF, msr);
> /* Setup access to the cache for under 640K. Note MC not setup yet. */
> msr.hi = 0x20000000;
> msr.lo = 0xfff80;
> wrmsr(MSR_GLIU0 + 0x20, msr);
> msr.hi = 0x20000000;
> msr.lo = 0x80fffe0;
> wrmsr(MSR_GLIU0 + 0x21, msr);
> msr.hi = 0x20000000;
> msr.lo = 0xfff80;
> wrmsr(MSR_GLIU1 + 0x20, msr);
> msr.hi = 0x20000000;
> msr.lo = 0x80fffe0;
> wrmsr(MSR_GLIU1 + 0x21, msr);
>
> +}

As this function is exactly the same for this board (and DB800), is it
possible that it's not really board-specific anyway? If so, it should
be moved to a global location in the chipset code.
> +static void mb_gpio_init(void)
> +{
> /* Early mainboard specific GPIO setup. */
>
> +}
>
> +void cache_as_ram_main(void)
> +{
> POST_CODE(0x01);
> static const struct mem_controller memctrl[] = {
> {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}}

I think you can/should just use DIMM0 / DIMM1 here.
> };
> SystemPreInit();
> msr_init();
> cs5536_early_setup();
> /* Note: must do this AFTER the early_setup! It is counting on some
> * early MSR setup for CS5536.
> */
> w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
> mb_gpio_init();
> uart_init();
> console_init();
> pll_reset(ManualConf);
> cpuRegInit();
> sdram_initialize(1, memctrl);
> /* Check memory. */
> /* ram_check(0x00000000, 640 * 1024); */
> /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
> return;
>
> +}
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/chip.h LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/chip.h
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/chip.h	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/chip.h	2007-11-26 09:50:43.000000000 +0500
> @@ -0,0 +1,25 @@
> +/*
> This file is part of the LinuxBIOS project.
> Copyright (C) 2007 Nikolay Petukhov
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> GNU General Public License for more details.
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> */
>
> +extern struct chip_operations mainboard_iei_pcisa_lx_ops;
>
> +struct mainboard_iei_pcisa_lx_config {
> int nothing;
>
> +};
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cmos.layout LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cmos.layout
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cmos.layout	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cmos.layout	2007-11-26 09:50:43.000000000 +0500

You have

default HAVE_OPTION_TABLE = 0
  default USE_OPTION_TABLE = 0

in Options.lb so this file is never used and we should drop it (or
enable it's usage, if it's tested and works).

Also, it should have a license header.
> @@ -0,0 +1,74 @@
> +entries
>
> +#start-bit length  config config-ID    name
> +#0            8       r       0        seconds
> +#8            8       r       0        alarm_seconds
> +#16           8       r       0        minutes
> +#24           8       r       0        alarm_minutes
> +#32           8       r       0        hours
> +#40           8       r       0        alarm_hours
> +#48           8       r       0        day_of_week
> +#56           8       r       0        day_of_month
> +#64           8       r       0        month
> +#72           8       r       0        year
> +#80           4       r       0        rate_select
> +#84           3       r       0        REF_Clock
> +#87           1       r       0        UIP
> +#88           1       r       0        auto_switch_DST
> +#89           1       r       0        24_hour_mode
> +#90           1       r       0        binary_values_enable
> +#91           1       r       0        square-wave_out_enable
> +#92           1       r       0        update_finished_enable
> +#93           1       r       0        alarm_interrupt_enable
> +#94           1       r       0        periodic_interrupt_enable
> +#95           1       r       0        disable_clock_updates
> +#96         288       r       0        temporary_filler
> +0          384       r       0        reserved_memory
> +384          1       e       4        boot_option
> +385          1       e       4        last_boot
> +386          1       e       1        ECC_memory
> +388          4       r       0        reboot_bits
> +392          3       e       5        baud_rate
> +400          1       e       1        power_on_after_fail
> +412          4       e       6        debug_level
> +416          4       e       7        boot_first
> +420          4       e       7        boot_second
> +424          4       e       7        boot_third
> +428          4       h       0        boot_index
> +432	     8       h       0        boot_countdown
> +1008         16      h       0        check_sum
>
> +enumerations
>
> +#ID value   text
> +1     0     Disable
> +1     1     Enable
> +2     0     Enable
> +2     1     Disable
> +4     0     Fallback
> +4     1     Normal
> +5     0     115200
> +5     1     57600
> +5     2     38400
> +5     3     19200
> +5     4     9600
> +5     5     4800
> +5     6     2400
> +5     7     1200
> +6     6     Notice
> +6     7     Info
> +6     8     Debug
> +6     9     Spew
> +7     0     Network
> +7     1     HDD
> +7     2     Floppy
> +7     8     Fallback_Network
> +7     9     Fallback_HDD
> +7     10    Fallback_Floppy
> +#7     3     ROM
>
> +checksums
>
> +checksum 392 1007 1008
>
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Config.lb LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Config.lb
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Config.lb	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Config.lb	2007-11-26 09:50:43.000000000 +0500

Add a license header, please.
> @@ -0,0 +1,194 @@
> +##
> +## Compute the location and size of where this firmware image
> +## (linuxBIOS plus bootloader) will live in the boot rom chip.
> +##
> +if USE_FALLBACK_IMAGE
> default ROM_SECTION_SIZE   = FALLBACK_SIZE
> default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
>
> +else
> default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
> default ROM_SECTION_OFFSET = 0
>
> +end
>
> +##
> +## Compute the start location and size size of
> +## The linuxBIOS bootloader.
> +##
>
> +default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
> +default PAYLOAD_SIZE			= ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
>
> +##
> +## Compute where this copy of linuxBIOS will start in the boot rom
> +##
> +default _ROMBASE	  = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
>
> +##
> +## Compute a range of ROM that can cached to speed up linuxBIOS,
> +## execution speed.
> +##
> +## XIP_ROM_SIZE must be a power of 2.
> +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
> +##
> +default XIP_ROM_SIZE=65536
> +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
>
> +##
> +## Set all of the defaults for an x86 architecture
> +##
>
> +arch i386 end
>
> +##
> +## Build the objects we have code for in this directory.
> +##
>
> +driver mainboard.o
>
> +if HAVE_PIRQ_TABLE
> object irq_tables.o
>
> +end
>
> +if USE_DCACHE_RAM
> #compile cache_as_ram.c to auto.inc
> makerule ./cache_as_ram_auto.inc
> 	depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
> 	action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
> 	action "perl -e 's/.rodata/.rom.data/g' -pi $@"
> 	action "perl -e 's/.text/.section .rom.text/g' -pi $@"
> end
>
> +end
>
> +##
> +## Build our 16 bit and 32 bit linuxBIOS entry code
> +##
> +mainboardinit cpu/x86/16bit/entry16.inc
> +mainboardinit cpu/x86/32bit/entry32.inc
> +ldscript /cpu/x86/16bit/entry16.lds
> +ldscript /cpu/x86/32bit/entry32.lds
>
> +##
> +## Build our reset vector (This is where linuxBIOS is entered)
> +##
> +if USE_FALLBACK_IMAGE
> mainboardinit cpu/x86/16bit/reset16.inc
> ldscript /cpu/x86/16bit/reset16.lds
>
> +else
> mainboardinit cpu/x86/32bit/reset32.inc
> ldscript /cpu/x86/32bit/reset32.lds
>
> +end
>
> +### Should this be in the northbridge code?
> +#not in serengeti_cheetah mainboardinit arch/i386/lib/cpu_reset.inc
>
> +##
> +## Include an id string (For safe flashing)
> +##
> +mainboardinit arch/i386/lib/id.inc
> +ldscript /arch/i386/lib/id.lds
>
> +###
> +### This is the early phase of linuxBIOS startup
> +### Things are delicate and we test to see if we should
> +### failover to another image.
> +###
> +if USE_FALLBACK_IMAGE
> ldscript /arch/i386/lib/failover.lds
>
> +#	mainboardinit ./failover.inc
> +end
>
> +###
> +### O.k. We aren't just an intermediary anymore!
> +###
>
> +##
> +## Setup RAM
> +##
> +mainboardinit cpu/x86/fpu/enable_fpu.inc
>
> +if USE_DCACHE_RAM
> mainboardinit cpu/amd/model_lx/cache_as_ram.inc
> mainboardinit ./cache_as_ram_auto.inc
>
> +end
>
> +##
> +## Include the secondary Configuration files
> +##
> +dir /pc80
> +config chip.h
>
> +chip northbridge/amd/lx
> device pci_domain 0 on
> device pci 1.0 on end				# Northbridge
> device pci 1.1 on end				# Graphics
> chip southbridge/amd/cs5536
> 	# IRQ 12 and 1 unmasked,  Keyboard and Mouse IRQs. OK
> 	# SIRQ Mode = Active(Quiet) mode. Save power....
> 	# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse, UARTs, etc IRQs. OK
> 	register "lpc_serirq_enable" = "0x000010da"
> 	register "lpc_serirq_polarity" = "0x0000EF25"
> 	register "lpc_serirq_mode" = "1"
> 	register "enable_gpio_int_route" = "0x0D0C0700"
> 	register "enable_ide_nand_flash" = "0"	# 0:ide mode, 1:flash
> 	register "enable_USBP4_device" = "1"	# 0: host, 1:device
> 	register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
> 	register "com1_enable" = "0"
> 	register "com1_address" = "0x3F8"
> 	register "com1_irq" = "4"
> 	register "com2_enable" = "0"
> 	register "com2_address" = "0x2F8"
> 	register "com2_irq" = "3"
> 	register "unwanted_vpci[0]" = "0"	# End of list has a zero
> 	device pci 9.0 on end			# Slot1
> 	device pci a.0 on end			# Slot2
> 	device pci b.0 on end			# Slot3
> 	device pci c.0 on end			# Slot4
> 	device pci e.0 on end			# Ethernet 0
> 	device pci 10.0 on end			# Ethernet 1
> 	device pci 11.0 on end			# SATA
> 	device pci f.0 on			# ISA Bridge
> 		chip superio/winbond/w83627hf
> 			device pnp 2e.0 off	# Floppy
> 				io 0x60 = 0x3f0
> 				irq 0x70 = 6
> 				drq 0x74 = 2
> 			end
> 			device pnp 2e.1 off	# Parallel port
> 				io 0x60 = 0x378
> 				irq 0x70 = 7
> 			end
> 			device pnp 2e.2 on	# Com1
> 				io 0x60 = 0x3f8
> 				irq 0x70 = 4
> 			end
> 			device pnp 2e.3 off end	# Com2
> 			device pnp 2e.5 on	# Keyboard
> 				io 0x60 = 0x60
> 				io 0x62 = 0x64
> 				irq 0x70 = 1
> 				irq 0x72 = 12
> 			end
> 			device pnp 2e.6 off end	# CIR
> 			device pnp 2e.7 off end	# GAME_MIDI_GIPO1
> 			device pnp 2e.8 off end	# GPIO2
> 			device pnp 2e.9 off end	# GPIO3
> 			device pnp 2e.a off end	# ACPI
> 			device pnp 2e.b off end	# HW Monitor
> 		end
> 	end
> 	device pci f.2 on end			# IDE Controller
> 	device pci f.3 on end			# Audio
> 	device pci f.4 on end			# OHCI
> 	device pci f.5 on end			# EHCI
> end
> end
> # APIC cluster is late CPU init.
> device apic_cluster 0 on
> chip cpu/amd/model_lx
> 	device apic 0 on end
> end
> end
>
> +end
>
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/failover.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/failover.c
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/failover.c	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/failover.c	2007-11-26 09:50:43.000000000 +0500
> @@ -0,0 +1,32 @@
> +/*
> This file is part of the LinuxBIOS project.
> Copyright (C) 2007 Nikolay Petukhov
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> GNU General Public License for more details.
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> */
>
> +#define ASSEMBLY 1
>
> +#include <stdint.h>
> +#include <device/pci_def.h>
> +#include <device/pci_ids.h>
> +#include <arch/io.h>
> +#include "pc80/mc146818rtc_early.c"
>
> +static unsigned long main(unsigned long bist)
> +{
> return bist;
>
> +}

Hm, does this mean it's not used at all? If so, drop the file
completely. You'll have to fix up the Config.lb file a bit so
it still compiles if you do that (grep for "failover").
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/irq_tables.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/irq_tables.c
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/irq_tables.c	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/irq_tables.c	2007-11-26 10:02:48.000000000 +0500
> @@ -0,0 +1,298 @@
> +/*
> This file is part of the LinuxBIOS project.
> Copyright (C) 2007 Nikolay Petukhov
> Borrowed from amd/db800.

Nope, this one is actually quite different from the DB800 file and
produced by you manually, I assume? If so, drop the "Borrowed from
amd/db800".
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> GNU General Public License for more details.
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> */
>
> +#include <arch/pirq_routing.h>
> +#include <console/console.h>
> +#include <arch/io.h>
> +#include <arch/pirq_routing.h>

arch/pirq_routing.h is only needed once, I think.
> +/* Platform IRQs */
> +#define PIRQA 11
> +#define PIRQB 10
> +#define PIRQC 11
> +#define PIRQD 5
>
> +/* Link */
> +#define LINK_PIRQA 1
> +#define LINK_PIRQB 2
> +#define LINK_PIRQC 3
> +#define LINK_PIRQD 4
> +#define LINK_NONE 0
>
> +/* Map */
> +#define IRQ_BITMAP_LINKA (1 << PIRQA)
> +#define IRQ_BITMAP_LINKB (1 << PIRQB)
> +#define IRQ_BITMAP_LINKC (1 << PIRQC)
> +#define IRQ_BITMAP_LINKD (1 << PIRQD)
> +#define IRQ_BITMAP_NOLINK 0x0
>
> +#define EXCLUSIVE_PCI_IRQS (IRQ_BITMAP_LINKA | IRQ_BITMAP_LINKB | IRQ_BITMAP_LINKC | IRQ_BITMAP_LINKD)
>
> +const struct irq_routing_table intel_irq_routing_table = {
> PIRQ_SIGNATURE,		/* u32 signature */
> PIRQ_VERSION,		/* u16 version   */
> 32 + 16 * IRQ_SLOT_COUNT,	/* there can be total 6 devices on the bus */
> 0x00,			/* Where the interrupt router lies (bus) */
> (0x0F << 3) | 0x0,	/* Where the interrupt router lies (dev) */
> EXCLUSIVE_PCI_IRQS,			/* IRQs devoted exclusively to PCI usage */
> 0x1078,			/* Vendor */
> 0x0002,			/* Device */
> 0,			/* Crap (miniport) */
> {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},	/* u8 rfu[11] */
> 0x62,			/*      u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
> .slots = {
> [0] = {
> 	.slot = 0x0,	/* means also "on board" */
> 	.bus = 0x00,
> 	.devfn = (0x01<<3)|0x0,	/* 0x01 is CS5536 */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		}
> 	}
> },
> [1] = {
> 	.slot = 0x0,	/* means also "on board" */
> 	.bus = 0x00,
> 	.devfn = (0x0f<<3)|0x0,	/* 0x0f is CS5536 (USB, AUDIO) */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_PIRQB, /* Audio */
> 			.bitmap = IRQ_BITMAP_LINKB
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_PIRQD, /* USB */
> 			.bitmap = IRQ_BITMAP_LINKD
> 		}
> 	}
> },
> [2] = {
> 	.slot = 0x0,	/* means also "on board" */
> 	.bus = 0x00,
> 	.devfn = (0x0e<<3)|0x0,	/* 0x0e is eth0 */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQD,
> 			.bitmap = IRQ_BITMAP_LINKD
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		}
> 	}
> },
> [3] = {
> 	.slot = 0x0,	/* means also "on board" */
> 	.bus = 0x00,
> 	.devfn = (0x10<<3)|0x0,	/* 0x10 is eth1 */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQB,
> 			.bitmap = IRQ_BITMAP_LINKB
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		}
> 	}
> },
> [4] = {
> 	.slot = 0x0,	/* means also "on board" */
> 	.bus = 0x00,
> 	.devfn = (0x11<<3)|0x0,	/* 0x11 is SATA */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_NONE,
> 			.bitmap = IRQ_BITMAP_NOLINK
> 		}
> 	}
> },
>
> +/*
> ################### backplane ###################
> */
>
> +/*
> Not exist on IP-6S, but it PCI1 on IP-7S.
> */

?

Are you trying to make this table compatible with two different boards?
If yes, does the rest of the code work fine with both of them?
> [5] = {
> 	.slot = 0x1,	/* This is real PCI slot. */
> 	.bus = 0x00,
> 	.devfn = (0x09<<3)|0x0,	/* 0x09 is PCI1 */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_PIRQB,
> 			.bitmap = IRQ_BITMAP_LINKB
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_PIRQC,
> 			.bitmap = IRQ_BITMAP_LINKC
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_PIRQD,
> 			.bitmap = IRQ_BITMAP_LINKD
> 		}
> 	}
> },
>
> +/*
> PCI2 IP-6S
> */
> [6] = {
> 	.slot = 0x2,	/* This is real PCI slot. */
> 	.bus = 0x00,
> 	.devfn = (0x0a<<3)|0x0,	/* 0x0a is PCI2 on IP-6S */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQD,
> 			.bitmap = IRQ_BITMAP_LINKD
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_PIRQB,
> 			.bitmap = IRQ_BITMAP_LINKB
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_PIRQC,
> 			.bitmap = IRQ_BITMAP_LINKC
> 		}
> 	}
> },
>
> +/*
> PCI3 IP-6S
> */
> [7] = {
> 	.slot = 0x3,	/* This is real PCI slot. */
> 	.bus = 0x00,
> 	.devfn = (0x0b<<3)|0x0,	/* 0x0b is PCI3 on IP-6S */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQC,
> 			.bitmap = IRQ_BITMAP_LINKC
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_PIRQD,
> 			.bitmap = IRQ_BITMAP_LINKD
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_PIRQB,
> 			.bitmap = IRQ_BITMAP_LINKB
> 		}
> 	}
> },
>
> +/*
> PCI4 IP-6S
> */
> [8] = {
> 	.slot = 0x4,	/* This is real PCI slot. */
> 	.bus = 0x00,
> 	.devfn = (0x0c<<3)|0x0,	/* 0x0c is PCI4 on IP-6S */
> 	.irq = {
> 		[0] = {	/* <-- 0 means this is INTA# output from the device or slot */
> 			.link = LINK_PIRQB,
> 			.bitmap = IRQ_BITMAP_LINKB
> 		},
> 		[1] = {	/* <-- 1 means this is INTB# output from the device or slot */
> 			.link = LINK_PIRQC,
> 			.bitmap = IRQ_BITMAP_LINKC
> 		},
> 		[2] = {	/* <-- 2 means this is INTC# output from the device or slot */
> 			.link = LINK_PIRQD,
> 			.bitmap = IRQ_BITMAP_LINKD
> 		},
> 		[3] = {	/* <-- 3 means this is INTD# output from the device or slot */
> 			.link = LINK_PIRQA,
> 			.bitmap = IRQ_BITMAP_LINKA
> 		}
> 	}
> },
> }
>
> +};
>
> +unsigned long write_pirq_routing_table(unsigned long addr)
> +{
> /* Put the PIR table in memory and checksum. */
> return 	copy_pirq_routing_table(addr);
>
> +}
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/mainboard.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/mainboard.c
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/mainboard.c	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/mainboard.c	2007-11-26 09:50:43.000000000 +0500
> @@ -0,0 +1,195 @@
> +/*
> This file is part of the LinuxBIOS project.
> Copyright (C) 2007 Nikolay Petukhov
> Borrowed from amd/db800.

This file is a plain copy of the DB800 file (+/- variable renames), and
it's a non-trivial amount of code IMHO, so please keep the original
copyright/license header.
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> GNU General Public License for more details.
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> */
>
> +#include <console/console.h>
> +#include <device/device.h>
> +#include <arch/io.h>
> +#include <cpu/x86/msr.h>
> +#include <cpu/amd/lxdef.h>
> +#include <device/pci_def.h>
> +#include "../../../southbridge/amd/cs5536/cs5536.h"
> +#include "chip.h"
>
> +/* Print the platform configuration - do before PCI init or it will not
> work right.
> */
>
> +void print_conf(void)
> +{
> +#if DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
> int i;
> unsigned long iol;
> msr_t msr;
> int cpu_msr_defs[] = { CPU_BC_L2_CONF, CPU_IM_CONFIG, CPU_DM_CONFIG0,
> CPU_RCONF_DEFAULT, CPU_RCONF_BYPASS, CPU_RCONF_A0_BF,
> CPU_RCONF_C0_DF, CPU_RCONF_E0_FF, CPU_RCONF_SMM, CPU_RCONF_DMM,
> GLCP_DELAY_CONTROLS, GL_END
> };
> int gliu0_msr_defs[] = { MSR_GLIU0_BASE1, MSR_GLIU0_BASE2,
> MSR_GLIU0_BASE4, MSR_GLIU0_BASE5, MSR_GLIU0_BASE6,
> GLIU0_P2D_BMO_0, GLIU0_P2D_BMO_1, MSR_GLIU0_SYSMEM,
> GLIU0_P2D_RO_0, GLIU0_P2D_RO_1, GLIU0_P2D_RO_2,
> MSR_GLIU0_SHADOW, GLIU0_IOD_BM_0, GLIU0_IOD_BM_1,
> GLIU0_IOD_BM_2, GLIU0_IOD_SC_0, GLIU0_IOD_SC_1, GLIU0_IOD_SC_2,
> GLIU0_IOD_SC_3, GLIU0_IOD_SC_4, GLIU0_IOD_SC_5,
> GLIU0_GLD_MSR_COH, GL_END
> };
> int gliu1_msr_defs[] = { MSR_GLIU1_BASE1, MSR_GLIU1_BASE2,
> MSR_GLIU1_BASE3, MSR_GLIU1_BASE4, MSR_GLIU1_BASE5,
> MSR_GLIU1_BASE6, MSR_GLIU1_BASE7, MSR_GLIU1_BASE8,
> MSR_GLIU1_BASE9, MSR_GLIU1_BASE10, GLIU1_P2D_R_0,
> GLIU1_P2D_R_1, GLIU1_P2D_R_2, GLIU1_P2D_R_3, MSR_GLIU1_SHADOW,
> GLIU1_IOD_BM_0, GLIU1_IOD_BM_1, GLIU1_IOD_BM_2, GLIU1_IOD_SC_0,
> GLIU1_IOD_SC_1, GLIU1_IOD_SC_2, GLIU1_IOD_SC_3,
> GLIU1_GLD_MSR_COH, GL_END
> };
> int rconf_msr[] = { CPU_RCONF0, CPU_RCONF1, CPU_RCONF2, CPU_RCONF3,
> CPU_RCONF4, CPU_RCONF5, CPU_RCONF6, CPU_RCONF7, GL_END
> };
> int cs5536_msr[] = { MDD_LBAR_GPIO, MDD_LBAR_FLSH0, MDD_LBAR_FLSH1,
> MDD_LEG_IO, MDD_PIN_OPT, MDD_IRQM_ZLOW, MDD_IRQM_ZHIGH,
> MDD_IRQM_PRIM, GL_END
> };
> int pci_msr[] = { GLPCI_CTRL, GLPCI_ARB, GLPCI_REN, GLPCI_A0_BF,
> GLPCI_C0_DF, GLPCI_E0_FF, GLPCI_RC0, GLPCI_RC1, GLPCI_RC2,
> GLPCI_RC3, GLPCI_ExtMSR, GLPCI_SPARE, GL_END
> };
> int dma_msr[] = { MDD_DMA_MAP, MDD_DMA_SHAD1, MDD_DMA_SHAD2,
> MDD_DMA_SHAD3, MDD_DMA_SHAD4, MDD_DMA_SHAD5, MDD_DMA_SHAD6,
> MDD_DMA_SHAD7, MDD_DMA_SHAD8, MDD_DMA_SHAD9, GL_END
> };
> printk_debug("---------- CPU ------------\n");
> for (i = 0; cpu_msr_defs[i] != GL_END; i++) {
> msr = rdmsr(cpu_msr_defs[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> 	     cpu_msr_defs[i], msr.hi, msr.lo);
> }
> printk_debug("---------- GLIU 0 ------------\n");
> for (i = 0; gliu0_msr_defs[i] != GL_END; i++) {
> msr = rdmsr(gliu0_msr_defs[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> 	     gliu0_msr_defs[i], msr.hi, msr.lo);
> }
> printk_debug("---------- GLIU 1 ------------\n");
> for (i = 0; gliu1_msr_defs[i] != GL_END; i++) {
> msr = rdmsr(gliu1_msr_defs[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> 	     gliu1_msr_defs[i], msr.hi, msr.lo);
> }
> printk_debug("---------- RCONF ------------\n");
> for (i = 0; rconf_msr[i] != GL_END; i++) {
> msr = rdmsr(rconf_msr[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", rconf_msr[i],
> 	     msr.hi, msr.lo);
> }
> printk_debug("---------- VARIA ------------\n");
> msr = rdmsr(0x51300010);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51300010, msr.hi,
>      msr.lo);
> msr = rdmsr(0x51400015);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51400015, msr.hi,
>      msr.lo);
> printk_debug("---------- DIVIL IRQ ------------\n");
> msr = rdmsr(MDD_IRQM_YLOW);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YLOW, msr.hi,
>      msr.lo);
> msr = rdmsr(MDD_IRQM_YHIGH);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YHIGH,
>      msr.hi, msr.lo);
> msr = rdmsr(MDD_IRQM_ZLOW);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZLOW, msr.hi,
>      msr.lo);
> msr = rdmsr(MDD_IRQM_ZHIGH);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZHIGH,
>      msr.hi, msr.lo);
> printk_debug("---------- PCI ------------\n");
> for (i = 0; pci_msr[i] != GL_END; i++) {
> msr = rdmsr(pci_msr[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", pci_msr[i],
> 	     msr.hi, msr.lo);
> }
> printk_debug("---------- LPC/UART DMA ------------\n");
> for (i = 0; dma_msr[i] != GL_END; i++) {
> msr = rdmsr(dma_msr[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", dma_msr[i],
> 	     msr.hi, msr.lo);
> }
> printk_debug("---------- CS5536 ------------\n");
> for (i = 0; cs5536_msr[i] != GL_END; i++) {
> msr = rdmsr(cs5536_msr[i]);
> printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cs5536_msr[i],
> 	     msr.hi, msr.lo);
> }
> iol = inl(GPIO_IO_BASE + GPIOL_INPUT_ENABLE);
> printk_debug("IOR 0x%08X is now 0x%08X\n",
>      GPIO_IO_BASE + GPIOL_INPUT_ENABLE, iol);
> iol = inl(GPIOL_EVENTS_ENABLE);
> printk_debug("IOR 0x%08X is now 0x%08X\n",
>      GPIO_IO_BASE + GPIOL_EVENTS_ENABLE, iol);
> iol = inl(GPIOL_INPUT_INVERT_ENABLE);
> printk_debug("IOR 0x%08X is now 0x%08X\n",
>      GPIO_IO_BASE + GPIOL_INPUT_INVERT_ENABLE, iol);
> iol = inl(GPIO_MAPPER_X);
> printk_debug("IOR 0x%08X is now 0x%08X\n", GPIO_IO_BASE + GPIO_MAPPER_X,
>      iol);
>
> +#endif				//DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
> +}

Yuck. Again a huge pile of code which can't be _that_ board-specific if
it works for at least two boards (this one and DB800). Should be moved elsewhere
IMO (but that's probably for an extra patch).
> +static void init(struct device *dev)
> +{
> printk_debug("IEI PCISA-LX ENTER %s\n", __FUNCTION__);
> printk_debug("IEI PCISA-LX EXIT %s\n", __FUNCTION__);
>
> +}
>
> +static void enable_dev(struct device *dev)
> +{
> dev->ops->init = init;
>
> +}
>
> +struct chip_operations mainboard_iei_pcisa_lx_ops = {
> CHIP_NAME("IEI PCISA-LX Mainboard")
> .enable_dev = enable_dev,
>
> +};
> diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Options.lb LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Options.lb
> --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Options.lb	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Options.lb	2007-11-26 09:50:43.000000000 +0500
> @@ -0,0 +1,180 @@
> +uses HAVE_MP_TABLE
> +uses HAVE_PIRQ_TABLE
> +uses USE_FALLBACK_IMAGE
> +uses HAVE_FALLBACK_BOOT
> +uses HAVE_HARD_RESET
> +uses HAVE_OPTION_TABLE
> +uses USE_OPTION_TABLE
> +uses CONFIG_ROM_PAYLOAD
> +uses IRQ_SLOT_COUNT
> +uses MAINBOARD
> +uses MAINBOARD_VENDOR
> +uses MAINBOARD_PART_NUMBER
> +uses LINUXBIOS_EXTRA_VERSION
> +uses ARCH
> +uses FALLBACK_SIZE
> +uses STACK_SIZE
> +uses HEAP_SIZE
> +uses ROM_SIZE
> +uses ROM_SECTION_SIZE
> +uses ROM_IMAGE_SIZE
> +uses ROM_SECTION_SIZE
> +uses ROM_SECTION_OFFSET
> +uses CONFIG_ROM_PAYLOAD_START
> +uses CONFIG_COMPRESS
> +uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
> +uses CONFIG_COMPRESSED_PAYLOAD_LZMA
> +uses CONFIG_PRECOMPRESSED_PAYLOAD
> +uses PAYLOAD_SIZE
> +uses _ROMBASE
> +uses _RAMBASE
> +uses XIP_ROM_SIZE
> +uses XIP_ROM_BASE
> +uses HAVE_MP_TABLE
> +uses CROSS_COMPILE
> +uses CC
> +uses HOSTCC
> +uses OBJCOPY
> +uses DEFAULT_CONSOLE_LOGLEVEL
> +uses MAXIMUM_CONSOLE_LOGLEVEL
> +uses CONFIG_CONSOLE_SERIAL8250
> +uses TTYS0_BAUD
> +uses TTYS0_BASE
> +uses TTYS0_LCS
> +uses CONFIG_UDELAY_IO
> +uses CONFIG_CONSOLE_VGA
> +uses CONFIG_PCI_ROM_RUN
> +uses CONFIG_VIDEO_MB
> +uses USE_DCACHE_RAM
> +uses DCACHE_RAM_BASE
> +uses DCACHE_RAM_SIZE
> +uses PIRQ_ROUTE
>
> +## ROM_SIZE is the size of boot ROM that this board will use.
> +default ROM_SIZE  = 256*1024
>
> +###
> +### Build options
> +###
> +default CONFIG_CONSOLE_VGA=0
> +default CONFIG_VIDEO_MB=8
> +default CONFIG_PCI_ROM_RUN=0
>
> +##
> +## Build code for the fallback boot
> +##
> +default HAVE_FALLBACK_BOOT=1
>
> +##
> +## no MP table
> +##
> +default HAVE_MP_TABLE=0
>
> +##
> +## Build code to reset the motherboard from linuxBIOS
> +##
> +default HAVE_HARD_RESET=0
>
> +## Delay timer options
> +##
> +default CONFIG_UDELAY_IO=1

This is a change from the DB800 target:

-default CONFIG_UDELAY_TSC=1
 -default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
 +default CONFIG_UDELAY_IO=1

No TSC or TIMER2 on Geode boards?
> +##
> +## Build code to export a programmable irq routing table
> +##
> +default HAVE_PIRQ_TABLE=1
> +default IRQ_SLOT_COUNT=9
> +default PIRQ_ROUTE=1
> +#object irq_tables.o
>
> +##
> +## Build code to export a CMOS option table
> +##
> +default HAVE_OPTION_TABLE=0
>
> +###
> +### LinuxBIOS layout values
> +###
>
> +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
> +default ROM_IMAGE_SIZE = 65536
> +default FALLBACK_SIZE = 131072
>
> +##
> +## enable CACHE_AS_RAM specifics
> +##
> +default USE_DCACHE_RAM=1
> +default DCACHE_RAM_BASE=0xc8000
> +default DCACHE_RAM_SIZE=0x08000
>
> +##
> +## Use a small 8K stack
> +##
> +default STACK_SIZE=0x2000
>
> +##
> +## Use a small 16K heap
> +##
> +default HEAP_SIZE=0x4000
>
> +##
> +## Only use the option table in a normal image
> +##
> +#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
> +default USE_OPTION_TABLE = 0
>
> +default _RAMBASE = 0x00004000
>
> +default CONFIG_ROM_PAYLOAD = 1
>
> +##
> +## The default compiler
> +##
> +default CROSS_COMPILE=""
> +default CC="$(CROSS_COMPILE)gcc -m32"
> +default HOSTCC="gcc"
>
> +##
> +## The Serial Console
> +##
>
> +# To Enable the Serial Console
> +default CONFIG_CONSOLE_SERIAL8250=1
>
> +## Select the serial console baud rate
> +default TTYS0_BAUD=115200
> +#default TTYS0_BAUD=57600
> +#default TTYS0_BAUD=38400
> +#default TTYS0_BAUD=19200
> +#default TTYS0_BAUD=9600
> +#default TTYS0_BAUD=4800
> +#default TTYS0_BAUD=2400
> +#default TTYS0_BAUD=1200
>
> +# Select the serial console base port
> +default TTYS0_BASE=0x3f8
>
> +# Select the serial protocol
> +# This defaults to 8 data bits, 1 stop bit, and no parity
> +default TTYS0_LCS=0x3
>
> +##
> +### Select the linuxBIOS loglevel
> +##
> +## EMERG      1   system is unusable
> +## ALERT      2   action must be taken immediately
> +## CRIT       3   critical conditions
> +## ERR        4   error conditions
> +## WARNING    5   warning conditions
> +## NOTICE     6   normal but significant condition
> +## INFO       7   informational
> +## DEBUG      8   debug-level messages
> +## SPEW       9   Way too many details
>
> +## Request this level of debugging output
> +default  DEFAULT_CONSOLE_LOGLEVEL=8
> +## At a maximum only compile in this level of debugging
> +default  MAXIMUM_CONSOLE_LOGLEVEL=8
>
> +end
>
> diff -Nru LinuxBIOSv2-2986/targets/iei/pcisa-lx/Config.lb LinuxBIOSv2-2986-lx/targets/iei/pcisa-lx/Config.lb
> --- LinuxBIOSv2-2986/targets/iei/pcisa-lx/Config.lb	1970-01-01 05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2986-lx/targets/iei/pcisa-lx/Config.lb	2007-11-26 10:13:13.000000000 +0500
> @@ -0,0 +1,43 @@
> +##
> +## This file is part of the LinuxBIOS project.
> +##
> +## Copyright (C) 2007 Nikolay Petukhov 
> +##
> +## This program is free software; you can redistribute it and/or modify
> +## it under the terms of the GNU General Public License as published by
> +## the Free Software Foundation; either version 2 of the License, or
> +## (at your option) any later version.
> +##
> +## This program is distributed in the hope that it will be useful,
> +## but WITHOUT ANY WARRANTY; without even the implied warranty of
> +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +## GNU General Public License for more details.
> +##
> +## You should have received a copy of the GNU General Public License
> +## along with this program; if not, write to the Free Software
> +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> +##
>
> +target pcisa-lx
> +mainboard iei/pcisa-lx
>
> +option CONFIG_COMPRESS=0
> +option CONFIG_PRECOMPRESSED_PAYLOAD=0
> +option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
> +option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
>
> +# Leave 36k for VSA.
> +option ROM_SIZE=512*1024-36*1024
> +option FALLBACK_SIZE=ROM_SIZE
>
> +option DEFAULT_CONSOLE_LOGLEVEL = 0
> +option MAXIMUM_CONSOLE_LOGLEVEL = 0
>
> +romimage "fallback"
> option USE_FALLBACK_IMAGE=1
> option ROM_IMAGE_SIZE=96*1024
> option LINUXBIOS_EXTRA_VERSION=".0Fallback"
> payload ../../payload.elf
>
> +end
>
> +buildrom ./pcisa-lx.rom ROM_SIZE "fallback"

Keep this "./linuxbios.rom" please, we do that will almost all boards
and it's a good thing IMO.

HTH, Uwe.

[Nikolay Petukhov]

Here is second edition of patch.
But it required pirq.patch from
http://www.linuxbios.org/pipermail/linuxbios/2007-November/027358.html
to support IRQ routing.

2007/11/27, Uwe Hermann :
> On Mon, Nov 26, 2007 at 12:25:45PM +0500, Nikolay Petukhov wrote:
> > This board (http://www.ieiworld.com/en/product_IPC.asp?model=PCISA-LX)
> > is based on amd-lx800/cs5536, so most of the on-board hardware is work
> > normally.
>
> Thanks a lot! Here's a quick review:
>
> I think the full name for this specific board is "PCISA-LX-R11",
> correct? If so, please use that everywhere (directory names, strings,
> variable names, comments). "PCISA-LX" seems to be the general name for a
> whole family of boards.
>
> So the directory name should probably be 'pcisa-lx-r11'.

On page http://www.ieiworld.com/en/product_IPC.asp?model=PCISA-LX ,
this board has Part No. PCISA-LX-800-R10.
So directory name should be pcisa-lx-800-r10.
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c   1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cache_as_ram_auto.c        2007-11-26 09:50:43.000000000 +0500
> > @@ -0,0 +1,138 @@
> > +/*
> > This file is part of the LinuxBIOS project.
> > Copyright (C) 2007 Nikolay Petukhov
> > Borrowed from amd/db800.
>
> Either the code you grabbed from the DB800 target is trivial (then drop
> this line completely), or it is not (then retain the Copyright lines from
> the respective DB800 file please).
>
> In this case the file is a plain copy of the DB800 one, with small fixes
> in the #defines at the beginning, so please keep the original
> copyright/license header and drop the "Borrowed from amd/db800".

Copyright retained from amd/db800.
> > This program is free software; you can redistribute it and/or modify
> > it under the terms of the GNU General Public License as published by
> > the Free Software Foundation; either version 2 of the License, or
> > (at your option) any later version.
> > This program is distributed in the hope that it will be useful,
> > but WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > GNU General Public License for more details.
> > You should have received a copy of the GNU General Public License
> > along with this program; if not, write to the Free Software
> > Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > */
> >
> > +#define ASSEMBLY 1
> >
> > +#include <stdint.h>
> > +#include <device/pci_def.h>
> > +#include <arch/io.h>
> > +#include <device/pnp_def.h>
> > +#include <arch/hlt.h>
> > +#include "pc80/serial.c"
> > +#include "arch/i386/lib/console.c"
> > +#include "ram/ramtest.c"
> > +#include "cpu/x86/bist.h"
> > +#include "cpu/x86/msr.h"
> > +#include <cpu/amd/lxdef.h>
> > +#include <cpu/amd/geode_post_code.h>
> > +#include "southbridge/amd/cs5536/cs5536.h"
> >
> > +#define POST_CODE(x) outb(x, 0x80)
> > +#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
> >
> > +#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
> > +#include "southbridge/amd/cs5536/cs5536_early_setup.c"
> > +#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
> >
> > +static inline int spd_read_byte(unsigned int device, unsigned int address)
> > +{
> > return smbus_read_byte(device, address);
> >
> > +}
> >
> > +#define ManualConf 1         /* Do automatic strapped PLL config */
> > +#define PLLMSRhi 0x0000059C /* CPU and GLIU mult/div 500/400*/
> > +#define PLLMSRhi 0x0000049C /* CPU and GLIU mult/div 500/333*/
> > +#define PLLMSRhi 0x0000039C /* CPU and GLIU mult/div 500/266*/
> > +//0x0000059C 0000 0000 0000 0000 0000 |0101 1|0|01 110|0
> > +/* Hold Count - how long we will sit in reset */
> > +#define PLLMSRlo 0x00DE6000
> >
> > +#define DIMM0 0xA0
> > +#define DIMM1 0xA2
> > +#include "northbridge/amd/lx/raminit.h"
> > +#include "northbridge/amd/lx/pll_reset.c"
> > +#include "northbridge/amd/lx/raminit.c"
> > +#include "sdram/generic_sdram.c"
> > +#include "cpu/amd/model_lx/cpureginit.c"
> > +#include "cpu/amd/model_lx/syspreinit.c"
> >
> > +static void msr_init(void)
> > +{
> > msr_t msr;
> > /* Setup access to the cache for under 1MB. */
> > msr.hi = 0x24fffc02;
> > msr.lo = 0x1000A000;    /* 0-A0000 write back */
> > wrmsr(CPU_RCONF_DEFAULT, msr);
> > msr.hi = 0x0;           /* Write back */
> > msr.lo = 0x0;
> > wrmsr(CPU_RCONF_A0_BF, msr);
> > wrmsr(CPU_RCONF_C0_DF, msr);
> > wrmsr(CPU_RCONF_E0_FF, msr);
> > /* Setup access to the cache for under 640K. Note MC not setup yet. */
> > msr.hi = 0x20000000;
> > msr.lo = 0xfff80;
> > wrmsr(MSR_GLIU0 + 0x20, msr);
> > msr.hi = 0x20000000;
> > msr.lo = 0x80fffe0;
> > wrmsr(MSR_GLIU0 + 0x21, msr);
> > msr.hi = 0x20000000;
> > msr.lo = 0xfff80;
> > wrmsr(MSR_GLIU1 + 0x20, msr);
> > msr.hi = 0x20000000;
> > msr.lo = 0x80fffe0;
> > wrmsr(MSR_GLIU1 + 0x21, msr);
> >
> > +}
>
> As this function is exactly the same for this board (and DB800), is it
> possible that it's not really board-specific anyway? If so, it should
> be moved to a global location in the chipset code.
> > +static void mb_gpio_init(void)
> > +{
> > /* Early mainboard specific GPIO setup. */
> >
> > +}
> >
> > +void cache_as_ram_main(void)
> > +{
> > POST_CODE(0x01);
> > static const struct mem_controller memctrl[] = {
> >         {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}}
>
> I think you can/should just use DIMM0 / DIMM1 here.

I am not sure.
> > };
> > SystemPreInit();
> > msr_init();
> > cs5536_early_setup();
> > /* Note: must do this AFTER the early_setup! It is counting on some
> >  * early MSR setup for CS5536.
> >  */
> > w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
> > mb_gpio_init();
> > uart_init();
> > console_init();
> > pll_reset(ManualConf);
> > cpuRegInit();
> > sdram_initialize(1, memctrl);
> > /* Check memory. */
> > /* ram_check(0x00000000, 640 * 1024); */
> > /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */
> > return;
> >
> > +}
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/chip.h LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/chip.h
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/chip.h        1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/chip.h     2007-11-26 09:50:43.000000000 +0500
> > @@ -0,0 +1,25 @@
> > +/*
> > This file is part of the LinuxBIOS project.
> > Copyright (C) 2007 Nikolay Petukhov
> > This program is free software; you can redistribute it and/or modify
> > it under the terms of the GNU General Public License as published by
> > the Free Software Foundation; either version 2 of the License, or
> > (at your option) any later version.
> > This program is distributed in the hope that it will be useful,
> > but WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > GNU General Public License for more details.
> > You should have received a copy of the GNU General Public License
> > along with this program; if not, write to the Free Software
> > Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > */
> >
> > +extern struct chip_operations mainboard_iei_pcisa_lx_ops;
> >
> > +struct mainboard_iei_pcisa_lx_config {
> > int nothing;
> >
> > +};
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cmos.layout LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cmos.layout
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/cmos.layout   1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/cmos.layout        2007-11-26 09:50:43.000000000 +0500
>
> You have
>
> default HAVE_OPTION_TABLE = 0
>   default USE_OPTION_TABLE = 0
>
> in Options.lb so this file is never used and we should drop it (or
> enable it's usage, if it's tested and works).
>
> Also, it should have a license header.

I corrected it.
> > @@ -0,0 +1,74 @@
> > +entries
> >
> > +#start-bit length  config config-ID    name
> > +#0            8       r       0        seconds
> > +#8            8       r       0        alarm_seconds
> > +#16           8       r       0        minutes
> > +#24           8       r       0        alarm_minutes
> > +#32           8       r       0        hours
> > +#40           8       r       0        alarm_hours
> > +#48           8       r       0        day_of_week
> > +#56           8       r       0        day_of_month
> > +#64           8       r       0        month
> > +#72           8       r       0        year
> > +#80           4       r       0        rate_select
> > +#84           3       r       0        REF_Clock
> > +#87           1       r       0        UIP
> > +#88           1       r       0        auto_switch_DST
> > +#89           1       r       0        24_hour_mode
> > +#90           1       r       0        binary_values_enable
> > +#91           1       r       0        square-wave_out_enable
> > +#92           1       r       0        update_finished_enable
> > +#93           1       r       0        alarm_interrupt_enable
> > +#94           1       r       0        periodic_interrupt_enable
> > +#95           1       r       0        disable_clock_updates
> > +#96         288       r       0        temporary_filler
> > +0          384       r       0        reserved_memory
> > +384          1       e       4        boot_option
> > +385          1       e       4        last_boot
> > +386          1       e       1        ECC_memory
> > +388          4       r       0        reboot_bits
> > +392          3       e       5        baud_rate
> > +400          1       e       1        power_on_after_fail
> > +412          4       e       6        debug_level
> > +416          4       e       7        boot_first
> > +420          4       e       7        boot_second
> > +424          4       e       7        boot_third
> > +428          4       h       0        boot_index
> > +432       8       h       0        boot_countdown
> > +1008         16      h       0        check_sum
> >
> > +enumerations
> >
> > +#ID value   text
> > +1     0     Disable
> > +1     1     Enable
> > +2     0     Enable
> > +2     1     Disable
> > +4     0     Fallback
> > +4     1     Normal
> > +5     0     115200
> > +5     1     57600
> > +5     2     38400
> > +5     3     19200
> > +5     4     9600
> > +5     5     4800
> > +5     6     2400
> > +5     7     1200
> > +6     6     Notice
> > +6     7     Info
> > +6     8     Debug
> > +6     9     Spew
> > +7     0     Network
> > +7     1     HDD
> > +7     2     Floppy
> > +7     8     Fallback_Network
> > +7     9     Fallback_HDD
> > +7     10    Fallback_Floppy
> > +#7     3     ROM
> >
> > +checksums
> >
> > +checksum 392 1007 1008
> >
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Config.lb LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Config.lb
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Config.lb     1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Config.lb  2007-11-26 09:50:43.000000000 +0500
>
> Add a license header, please.
> > @@ -0,0 +1,194 @@
> > +##
> > +## Compute the location and size of where this firmware image
> > +## (linuxBIOS plus bootloader) will live in the boot rom chip.
> > +##
> > +if USE_FALLBACK_IMAGE
> > default ROM_SECTION_SIZE   = FALLBACK_SIZE
> > default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
> >
> > +else
> > default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
> > default ROM_SECTION_OFFSET = 0
> >
> > +end
> >
> > +##
> > +## Compute the start location and size size of
> > +## The linuxBIOS bootloader.
> > +##
> >
> > +default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
> > +default PAYLOAD_SIZE                 = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
> >
> > +##
> > +## Compute where this copy of linuxBIOS will start in the boot rom
> > +##
> > +default _ROMBASE       = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
> >
> > +##
> > +## Compute a range of ROM that can cached to speed up linuxBIOS,
> > +## execution speed.
> > +##
> > +## XIP_ROM_SIZE must be a power of 2.
> > +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
> > +##
> > +default XIP_ROM_SIZE=65536
> > +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
> >
> > +##
> > +## Set all of the defaults for an x86 architecture
> > +##
> >
> > +arch i386 end
> >
> > +##
> > +## Build the objects we have code for in this directory.
> > +##
> >
> > +driver mainboard.o
> >
> > +if HAVE_PIRQ_TABLE
> > object irq_tables.o
> >
> > +end
> >
> > +if USE_DCACHE_RAM
> > #compile cache_as_ram.c to auto.inc
> > makerule ./cache_as_ram_auto.inc
> >                 depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
> >                 action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
> >                 action "perl -e 's/.rodata/.rom.data/g' -pi $@"
> >                 action "perl -e 's/.text/.section .rom.text/g' -pi $@"
> > end
> >
> > +end
> >
> > +##
> > +## Build our 16 bit and 32 bit linuxBIOS entry code
> > +##
> > +mainboardinit cpu/x86/16bit/entry16.inc
> > +mainboardinit cpu/x86/32bit/entry32.inc
> > +ldscript /cpu/x86/16bit/entry16.lds
> > +ldscript /cpu/x86/32bit/entry32.lds
> >
> > +##
> > +## Build our reset vector (This is where linuxBIOS is entered)
> > +##
> > +if USE_FALLBACK_IMAGE
> > mainboardinit cpu/x86/16bit/reset16.inc
> > ldscript /cpu/x86/16bit/reset16.lds
> >
> > +else
> > mainboardinit cpu/x86/32bit/reset32.inc
> > ldscript /cpu/x86/32bit/reset32.lds
> >
> > +end
> >
> > +### Should this be in the northbridge code?
> > +#not in serengeti_cheetah mainboardinit arch/i386/lib/cpu_reset.inc
> >
> > +##
> > +## Include an id string (For safe flashing)
> > +##
> > +mainboardinit arch/i386/lib/id.inc
> > +ldscript /arch/i386/lib/id.lds
> >
> > +###
> > +### This is the early phase of linuxBIOS startup
> > +### Things are delicate and we test to see if we should
> > +### failover to another image.
> > +###
> > +if USE_FALLBACK_IMAGE
> > ldscript /arch/i386/lib/failover.lds
> >
> > +#    mainboardinit ./failover.inc
> > +end
> >
> > +###
> > +### O.k. We aren't just an intermediary anymore!
> > +###
> >
> > +##
> > +## Setup RAM
> > +##
> > +mainboardinit cpu/x86/fpu/enable_fpu.inc
> >
> > +if USE_DCACHE_RAM
> > mainboardinit cpu/amd/model_lx/cache_as_ram.inc
> > mainboardinit ./cache_as_ram_auto.inc
> >
> > +end
> >
> > +##
> > +## Include the secondary Configuration files
> > +##
> > +dir /pc80
> > +config chip.h
> >
> > +chip northbridge/amd/lx
> > device pci_domain 0 on
> >         device pci 1.0 on end                           # Northbridge
> >         device pci 1.1 on end                           # Graphics
> >         chip southbridge/amd/cs5536
> >                 # IRQ 12 and 1 unmasked,  Keyboard and Mouse IRQs. OK
> >                 # SIRQ Mode = Active(Quiet) mode. Save power....
> >                 # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse, UARTs, etc IRQs. OK
> >                 register "lpc_serirq_enable" = "0x000010da"
> >                 register "lpc_serirq_polarity" = "0x0000EF25"
> >                 register "lpc_serirq_mode" = "1"
> >                 register "enable_gpio_int_route" = "0x0D0C0700"
> >                 register "enable_ide_nand_flash" = "0"  # 0:ide mode, 1:flash
> >                 register "enable_USBP4_device" = "1"    # 0: host, 1:device
> >                 register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
> >                 register "com1_enable" = "0"
> >                 register "com1_address" = "0x3F8"
> >                 register "com1_irq" = "4"
> >                 register "com2_enable" = "0"
> >                 register "com2_address" = "0x2F8"
> >                 register "com2_irq" = "3"
> >                 register "unwanted_vpci[0]" = "0"       # End of list has a zero
> >                 device pci 9.0 on end                   # Slot1
> >                 device pci a.0 on end                   # Slot2
> >                 device pci b.0 on end                   # Slot3
> >                 device pci c.0 on end                   # Slot4
> >                 device pci e.0 on end                   # Ethernet 0
> >                 device pci 10.0 on end                  # Ethernet 1
> >                 device pci 11.0 on end                  # SATA
> >                 device pci f.0 on                       # ISA Bridge
> >                         chip superio/winbond/w83627hf
> >                                 device pnp 2e.0 off     # Floppy
> >                                         io 0x60 = 0x3f0
> >                                         irq 0x70 = 6
> >                                         drq 0x74 = 2
> >                                 end
> >                                 device pnp 2e.1 off     # Parallel port
> >                                         io 0x60 = 0x378
> >                                         irq 0x70 = 7
> >                                 end
> >                                 device pnp 2e.2 on      # Com1
> >                                         io 0x60 = 0x3f8
> >                                         irq 0x70 = 4
> >                                 end
> >                                 device pnp 2e.3 off end # Com2
> >                                 device pnp 2e.5 on      # Keyboard
> >                                         io 0x60 = 0x60
> >                                         io 0x62 = 0x64
> >                                         irq 0x70 = 1
> >                                         irq 0x72 = 12
> >                                 end
> >                                 device pnp 2e.6 off end # CIR
> >                                 device pnp 2e.7 off end # GAME_MIDI_GIPO1
> >                                 device pnp 2e.8 off end # GPIO2
> >                                 device pnp 2e.9 off end # GPIO3
> >                                 device pnp 2e.a off end # ACPI
> >                                 device pnp 2e.b off end # HW Monitor
> >                         end
> >                 end
> >                 device pci f.2 on end                   # IDE Controller
> >                 device pci f.3 on end                   # Audio
> >                 device pci f.4 on end                   # OHCI
> >                 device pci f.5 on end                   # EHCI
> >         end
> > end
> > # APIC cluster is late CPU init.
> > device apic_cluster 0 on
> >         chip cpu/amd/model_lx
> >                 device apic 0 on end
> >         end
> > end
> >
> > +end
> >
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/failover.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/failover.c
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/failover.c    1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/failover.c 2007-11-26 09:50:43.000000000 +0500
> > @@ -0,0 +1,32 @@
> > +/*
> > This file is part of the LinuxBIOS project.
> > Copyright (C) 2007 Nikolay Petukhov
> > This program is free software; you can redistribute it and/or modify
> > it under the terms of the GNU General Public License as published by
> > the Free Software Foundation; either version 2 of the License, or
> > (at your option) any later version.
> > This program is distributed in the hope that it will be useful,
> > but WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > GNU General Public License for more details.
> > You should have received a copy of the GNU General Public License
> > along with this program; if not, write to the Free Software
> > Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > */
> >
> > +#define ASSEMBLY 1
> >
> > +#include <stdint.h>
> > +#include <device/pci_def.h>
> > +#include <device/pci_ids.h>
> > +#include <arch/io.h>
> > +#include "pc80/mc146818rtc_early.c"
> >
> > +static unsigned long main(unsigned long bist)
> > +{
> > return bist;
> >
> > +}
>
> Hm, does this mean it's not used at all? If so, drop the file
> completely. You'll have to fix up the Config.lb file a bit so
> it still compiles if you do that (grep for "failover").

I corrected it.
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/irq_tables.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/irq_tables.c
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/irq_tables.c  1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/irq_tables.c       2007-11-26 10:02:48.000000000 +0500
> > @@ -0,0 +1,298 @@
> > +/*
> > This file is part of the LinuxBIOS project.
> > Copyright (C) 2007 Nikolay Petukhov
> > Borrowed from amd/db800.
>
> Nope, this one is actually quite different from the DB800 file and
> produced by you manually, I assume? If so, drop the "Borrowed from
> amd/db800".
> > This program is free software; you can redistribute it and/or modify
> > it under the terms of the GNU General Public License as published by
> > the Free Software Foundation; either version 2 of the License, or
> > (at your option) any later version.
> > This program is distributed in the hope that it will be useful,
> > but WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > GNU General Public License for more details.
> > You should have received a copy of the GNU General Public License
> > along with this program; if not, write to the Free Software
> > Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > */
> >
> > +#include <arch/pirq_routing.h>
> > +#include <console/console.h>
> > +#include <arch/io.h>
> > +#include <arch/pirq_routing.h>
>
> arch/pirq_routing.h is only needed once, I think.

I drop it.
> > +/* Platform IRQs */
> > +#define PIRQA 11
> > +#define PIRQB 10
> > +#define PIRQC 11
> > +#define PIRQD 5
> >
> > +/* Link */
> > +#define LINK_PIRQA 1
> > +#define LINK_PIRQB 2
> > +#define LINK_PIRQC 3
> > +#define LINK_PIRQD 4
> > +#define LINK_NONE 0
> >
> > +/* Map */
> > +#define IRQ_BITMAP_LINKA (1 << PIRQA)
> > +#define IRQ_BITMAP_LINKB (1 << PIRQB)
> > +#define IRQ_BITMAP_LINKC (1 << PIRQC)
> > +#define IRQ_BITMAP_LINKD (1 << PIRQD)
> > +#define IRQ_BITMAP_NOLINK 0x0
> >
> > +#define EXCLUSIVE_PCI_IRQS (IRQ_BITMAP_LINKA | IRQ_BITMAP_LINKB | IRQ_BITMAP_LINKC | IRQ_BITMAP_LINKD)
> >
> > +const struct irq_routing_table intel_irq_routing_table = {
> > PIRQ_SIGNATURE,         /* u32 signature */
> > PIRQ_VERSION,           /* u16 version   */
> > 32 + 16 * IRQ_SLOT_COUNT,       /* there can be total 6 devices on the bus */
> > 0x00,                   /* Where the interrupt router lies (bus) */
> > (0x0F << 3) | 0x0,      /* Where the interrupt router lies (dev) */
> > EXCLUSIVE_PCI_IRQS,                     /* IRQs devoted exclusively to PCI usage */
> > 0x1078,                 /* Vendor */
> > 0x0002,                 /* Device */
> > 0,                      /* Crap (miniport) */
> > {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},      /* u8 rfu[11] */
> > 0x62,                   /*      u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
> > .slots = {
> >         [0] = {
> >                 .slot = 0x0,    /* means also "on board" */
> >                 .bus = 0x00,
> >                 .devfn = (0x01<<3)|0x0, /* 0x01 is CS5536 */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         }
> >                 }
> >         },
> >         [1] = {
> >                 .slot = 0x0,    /* means also "on board" */
> >                 .bus = 0x00,
> >                 .devfn = (0x0f<<3)|0x0, /* 0x0f is CS5536 (USB, AUDIO) */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_PIRQB, /* Audio */
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_PIRQD, /* USB */
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         }
> >                 }
> >         },
> >         [2] = {
> >                 .slot = 0x0,    /* means also "on board" */
> >                 .bus = 0x00,
> >                 .devfn = (0x0e<<3)|0x0, /* 0x0e is eth0 */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQD,
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         }
> >                 }
> >         },
> >         [3] = {
> >                 .slot = 0x0,    /* means also "on board" */
> >                 .bus = 0x00,
> >                 .devfn = (0x10<<3)|0x0, /* 0x10 is eth1 */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQB,
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         }
> >                 }
> >         },
> >         [4] = {
> >                 .slot = 0x0,    /* means also "on board" */
> >                 .bus = 0x00,
> >                 .devfn = (0x11<<3)|0x0, /* 0x11 is SATA */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_NONE,
> >                                 .bitmap = IRQ_BITMAP_NOLINK
> >                         }
> >                 }
> >         },
> >
> > +/*
> > ################### backplane ###################
> > */
> >
> > +/*
> > Not exist on IP-6S, but it PCI1 on IP-7S.
> > */
>
> ?
>
> Are you trying to make this table compatible with two different boards?
> If yes, does the rest of the code work fine with both of them?

Yes, RIR table formed to correct work the PCISA-LX with various backplanes.
> >         [5] = {
> >                 .slot = 0x1,    /* This is real PCI slot. */
> >                 .bus = 0x00,
> >                 .devfn = (0x09<<3)|0x0, /* 0x09 is PCI1 */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_PIRQB,
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_PIRQC,
> >                                 .bitmap = IRQ_BITMAP_LINKC
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_PIRQD,
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         }
> >                 }
> >         },
> >
> > +/*
> > PCI2 IP-6S
> > */
> >         [6] = {
> >                 .slot = 0x2,    /* This is real PCI slot. */
> >                 .bus = 0x00,
> >                 .devfn = (0x0a<<3)|0x0, /* 0x0a is PCI2 on IP-6S */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQD,
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_PIRQB,
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_PIRQC,
> >                                 .bitmap = IRQ_BITMAP_LINKC
> >                         }
> >                 }
> >         },
> >
> > +/*
> > PCI3 IP-6S
> > */
> >         [7] = {
> >                 .slot = 0x3,    /* This is real PCI slot. */
> >                 .bus = 0x00,
> >                 .devfn = (0x0b<<3)|0x0, /* 0x0b is PCI3 on IP-6S */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQC,
> >                                 .bitmap = IRQ_BITMAP_LINKC
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_PIRQD,
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_PIRQB,
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         }
> >                 }
> >         },
> >
> > +/*
> > PCI4 IP-6S
> > */
> >         [8] = {
> >                 .slot = 0x4,    /* This is real PCI slot. */
> >                 .bus = 0x00,
> >                 .devfn = (0x0c<<3)|0x0, /* 0x0c is PCI4 on IP-6S */
> >                 .irq = {
> >                         [0] = { /* <-- 0 means this is INTA# output from the device or slot */
> >                                 .link = LINK_PIRQB,
> >                                 .bitmap = IRQ_BITMAP_LINKB
> >                         },
> >                         [1] = { /* <-- 1 means this is INTB# output from the device or slot */
> >                                 .link = LINK_PIRQC,
> >                                 .bitmap = IRQ_BITMAP_LINKC
> >                         },
> >                         [2] = { /* <-- 2 means this is INTC# output from the device or slot */
> >                                 .link = LINK_PIRQD,
> >                                 .bitmap = IRQ_BITMAP_LINKD
> >                         },
> >                         [3] = { /* <-- 3 means this is INTD# output from the device or slot */
> >                                 .link = LINK_PIRQA,
> >                                 .bitmap = IRQ_BITMAP_LINKA
> >                         }
> >                 }
> >         },
> > }
> >
> > +};
> >
> > +unsigned long write_pirq_routing_table(unsigned long addr)
> > +{
> > /* Put the PIR table in memory and checksum. */
> > return  copy_pirq_routing_table(addr);
> >
> > +}
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/mainboard.c LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/mainboard.c
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/mainboard.c   1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/mainboard.c        2007-11-26 09:50:43.000000000 +0500
> > @@ -0,0 +1,195 @@
> > +/*
> > This file is part of the LinuxBIOS project.
> > Copyright (C) 2007 Nikolay Petukhov
> > Borrowed from amd/db800.
>
> This file is a plain copy of the DB800 file (+/- variable renames), and
> it's a non-trivial amount of code IMHO, so please keep the original
> copyright/license header.

Copyright retained from amd/db800.
> > This program is free software; you can redistribute it and/or modify
> > it under the terms of the GNU General Public License as published by
> > the Free Software Foundation; either version 2 of the License, or
> > (at your option) any later version.
> > This program is distributed in the hope that it will be useful,
> > but WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > GNU General Public License for more details.
> > You should have received a copy of the GNU General Public License
> > along with this program; if not, write to the Free Software
> > Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > */
> >
> > +#include <console/console.h>
> > +#include <device/device.h>
> > +#include <arch/io.h>
> > +#include <cpu/x86/msr.h>
> > +#include <cpu/amd/lxdef.h>
> > +#include <device/pci_def.h>
> > +#include "../../../southbridge/amd/cs5536/cs5536.h"
> > +#include "chip.h"
> >
> > +/* Print the platform configuration - do before PCI init or it will not
> > work right.
> > */
> >
> > +void print_conf(void)
> > +{
> > +#if DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
> > int i;
> > unsigned long iol;
> > msr_t msr;
> > int cpu_msr_defs[] = { CPU_BC_L2_CONF, CPU_IM_CONFIG, CPU_DM_CONFIG0,
> >         CPU_RCONF_DEFAULT, CPU_RCONF_BYPASS, CPU_RCONF_A0_BF,
> >         CPU_RCONF_C0_DF, CPU_RCONF_E0_FF, CPU_RCONF_SMM, CPU_RCONF_DMM,
> >         GLCP_DELAY_CONTROLS, GL_END
> > };
> > int gliu0_msr_defs[] = { MSR_GLIU0_BASE1, MSR_GLIU0_BASE2,
> >         MSR_GLIU0_BASE4, MSR_GLIU0_BASE5, MSR_GLIU0_BASE6,
> >         GLIU0_P2D_BMO_0, GLIU0_P2D_BMO_1, MSR_GLIU0_SYSMEM,
> >         GLIU0_P2D_RO_0, GLIU0_P2D_RO_1, GLIU0_P2D_RO_2,
> >         MSR_GLIU0_SHADOW, GLIU0_IOD_BM_0, GLIU0_IOD_BM_1,
> >         GLIU0_IOD_BM_2, GLIU0_IOD_SC_0, GLIU0_IOD_SC_1, GLIU0_IOD_SC_2,
> >         GLIU0_IOD_SC_3, GLIU0_IOD_SC_4, GLIU0_IOD_SC_5,
> >         GLIU0_GLD_MSR_COH, GL_END
> > };
> > int gliu1_msr_defs[] = { MSR_GLIU1_BASE1, MSR_GLIU1_BASE2,
> >         MSR_GLIU1_BASE3, MSR_GLIU1_BASE4, MSR_GLIU1_BASE5,
> >         MSR_GLIU1_BASE6, MSR_GLIU1_BASE7, MSR_GLIU1_BASE8,
> >         MSR_GLIU1_BASE9, MSR_GLIU1_BASE10, GLIU1_P2D_R_0,
> >         GLIU1_P2D_R_1, GLIU1_P2D_R_2, GLIU1_P2D_R_3, MSR_GLIU1_SHADOW,
> >         GLIU1_IOD_BM_0, GLIU1_IOD_BM_1, GLIU1_IOD_BM_2, GLIU1_IOD_SC_0,
> >         GLIU1_IOD_SC_1, GLIU1_IOD_SC_2, GLIU1_IOD_SC_3,
> >         GLIU1_GLD_MSR_COH, GL_END
> > };
> > int rconf_msr[] = { CPU_RCONF0, CPU_RCONF1, CPU_RCONF2, CPU_RCONF3,
> >         CPU_RCONF4, CPU_RCONF5, CPU_RCONF6, CPU_RCONF7, GL_END
> > };
> > int cs5536_msr[] = { MDD_LBAR_GPIO, MDD_LBAR_FLSH0, MDD_LBAR_FLSH1,
> >         MDD_LEG_IO, MDD_PIN_OPT, MDD_IRQM_ZLOW, MDD_IRQM_ZHIGH,
> >         MDD_IRQM_PRIM, GL_END
> > };
> > int pci_msr[] = { GLPCI_CTRL, GLPCI_ARB, GLPCI_REN, GLPCI_A0_BF,
> >         GLPCI_C0_DF, GLPCI_E0_FF, GLPCI_RC0, GLPCI_RC1, GLPCI_RC2,
> >         GLPCI_RC3, GLPCI_ExtMSR, GLPCI_SPARE, GL_END
> > };
> > int dma_msr[] = { MDD_DMA_MAP, MDD_DMA_SHAD1, MDD_DMA_SHAD2,
> >         MDD_DMA_SHAD3, MDD_DMA_SHAD4, MDD_DMA_SHAD5, MDD_DMA_SHAD6,
> >         MDD_DMA_SHAD7, MDD_DMA_SHAD8, MDD_DMA_SHAD9, GL_END
> > };
> > printk_debug("---------- CPU ------------\n");
> > for (i = 0; cpu_msr_defs[i] != GL_END; i++) {
> >         msr = rdmsr(cpu_msr_defs[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> >                      cpu_msr_defs[i], msr.hi, msr.lo);
> > }
> > printk_debug("---------- GLIU 0 ------------\n");
> > for (i = 0; gliu0_msr_defs[i] != GL_END; i++) {
> >         msr = rdmsr(gliu0_msr_defs[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> >                      gliu0_msr_defs[i], msr.hi, msr.lo);
> > }
> > printk_debug("---------- GLIU 1 ------------\n");
> > for (i = 0; gliu1_msr_defs[i] != GL_END; i++) {
> >         msr = rdmsr(gliu1_msr_defs[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n",
> >                      gliu1_msr_defs[i], msr.hi, msr.lo);
> > }
> > printk_debug("---------- RCONF ------------\n");
> > for (i = 0; rconf_msr[i] != GL_END; i++) {
> >         msr = rdmsr(rconf_msr[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", rconf_msr[i],
> >                      msr.hi, msr.lo);
> > }
> > printk_debug("---------- VARIA ------------\n");
> > msr = rdmsr(0x51300010);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51300010, msr.hi,
> >              msr.lo);
> > msr = rdmsr(0x51400015);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51400015, msr.hi,
> >              msr.lo);
> > printk_debug("---------- DIVIL IRQ ------------\n");
> > msr = rdmsr(MDD_IRQM_YLOW);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YLOW, msr.hi,
> >              msr.lo);
> > msr = rdmsr(MDD_IRQM_YHIGH);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YHIGH,
> >              msr.hi, msr.lo);
> > msr = rdmsr(MDD_IRQM_ZLOW);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZLOW, msr.hi,
> >              msr.lo);
> > msr = rdmsr(MDD_IRQM_ZHIGH);
> > printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZHIGH,
> >              msr.hi, msr.lo);
> > printk_debug("---------- PCI ------------\n");
> > for (i = 0; pci_msr[i] != GL_END; i++) {
> >         msr = rdmsr(pci_msr[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", pci_msr[i],
> >                      msr.hi, msr.lo);
> > }
> > printk_debug("---------- LPC/UART DMA ------------\n");
> > for (i = 0; dma_msr[i] != GL_END; i++) {
> >         msr = rdmsr(dma_msr[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", dma_msr[i],
> >                      msr.hi, msr.lo);
> > }
> > printk_debug("---------- CS5536 ------------\n");
> > for (i = 0; cs5536_msr[i] != GL_END; i++) {
> >         msr = rdmsr(cs5536_msr[i]);
> >         printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cs5536_msr[i],
> >                      msr.hi, msr.lo);
> > }
> > iol = inl(GPIO_IO_BASE + GPIOL_INPUT_ENABLE);
> > printk_debug("IOR 0x%08X is now 0x%08X\n",
> >              GPIO_IO_BASE + GPIOL_INPUT_ENABLE, iol);
> > iol = inl(GPIOL_EVENTS_ENABLE);
> > printk_debug("IOR 0x%08X is now 0x%08X\n",
> >              GPIO_IO_BASE + GPIOL_EVENTS_ENABLE, iol);
> > iol = inl(GPIOL_INPUT_INVERT_ENABLE);
> > printk_debug("IOR 0x%08X is now 0x%08X\n",
> >              GPIO_IO_BASE + GPIOL_INPUT_INVERT_ENABLE, iol);
> > iol = inl(GPIO_MAPPER_X);
> > printk_debug("IOR 0x%08X is now 0x%08X\n", GPIO_IO_BASE + GPIO_MAPPER_X,
> >              iol);
> >
> > +#endif                               //DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
> > +}
>
> Yuck. Again a huge pile of code which can't be _that_ board-specific if
> it works for at least two boards (this one and DB800). Should be moved elsewhere
> IMO (but that's probably for an extra patch).
> > +static void init(struct device *dev)
> > +{
> > printk_debug("IEI PCISA-LX ENTER %s\n", __FUNCTION__);
> > printk_debug("IEI PCISA-LX EXIT %s\n", __FUNCTION__);
> >
> > +}
> >
> > +static void enable_dev(struct device *dev)
> > +{
> > dev->ops->init = init;
> >
> > +}
> >
> > +struct chip_operations mainboard_iei_pcisa_lx_ops = {
> > CHIP_NAME("IEI PCISA-LX Mainboard")
> > .enable_dev = enable_dev,
> >
> > +};
> > diff -Nru LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Options.lb LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Options.lb
> > --- LinuxBIOSv2-2986/src/mainboard/iei/pcisa-lx/Options.lb    1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/src/mainboard/iei/pcisa-lx/Options.lb 2007-11-26 09:50:43.000000000 +0500
> > @@ -0,0 +1,180 @@
> > +uses HAVE_MP_TABLE
> > +uses HAVE_PIRQ_TABLE
> > +uses USE_FALLBACK_IMAGE
> > +uses HAVE_FALLBACK_BOOT
> > +uses HAVE_HARD_RESET
> > +uses HAVE_OPTION_TABLE
> > +uses USE_OPTION_TABLE
> > +uses CONFIG_ROM_PAYLOAD
> > +uses IRQ_SLOT_COUNT
> > +uses MAINBOARD
> > +uses MAINBOARD_VENDOR
> > +uses MAINBOARD_PART_NUMBER
> > +uses LINUXBIOS_EXTRA_VERSION
> > +uses ARCH
> > +uses FALLBACK_SIZE
> > +uses STACK_SIZE
> > +uses HEAP_SIZE
> > +uses ROM_SIZE
> > +uses ROM_SECTION_SIZE
> > +uses ROM_IMAGE_SIZE
> > +uses ROM_SECTION_SIZE
> > +uses ROM_SECTION_OFFSET
> > +uses CONFIG_ROM_PAYLOAD_START
> > +uses CONFIG_COMPRESS
> > +uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
> > +uses CONFIG_COMPRESSED_PAYLOAD_LZMA
> > +uses CONFIG_PRECOMPRESSED_PAYLOAD
> > +uses PAYLOAD_SIZE
> > +uses _ROMBASE
> > +uses _RAMBASE
> > +uses XIP_ROM_SIZE
> > +uses XIP_ROM_BASE
> > +uses HAVE_MP_TABLE
> > +uses CROSS_COMPILE
> > +uses CC
> > +uses HOSTCC
> > +uses OBJCOPY
> > +uses DEFAULT_CONSOLE_LOGLEVEL
> > +uses MAXIMUM_CONSOLE_LOGLEVEL
> > +uses CONFIG_CONSOLE_SERIAL8250
> > +uses TTYS0_BAUD
> > +uses TTYS0_BASE
> > +uses TTYS0_LCS
> > +uses CONFIG_UDELAY_IO
> > +uses CONFIG_CONSOLE_VGA
> > +uses CONFIG_PCI_ROM_RUN
> > +uses CONFIG_VIDEO_MB
> > +uses USE_DCACHE_RAM
> > +uses DCACHE_RAM_BASE
> > +uses DCACHE_RAM_SIZE
> > +uses PIRQ_ROUTE
> >
> > +## ROM_SIZE is the size of boot ROM that this board will use.
> > +default ROM_SIZE  = 256*1024
> >
> > +###
> > +### Build options
> > +###
> > +default CONFIG_CONSOLE_VGA=0
> > +default CONFIG_VIDEO_MB=8
> > +default CONFIG_PCI_ROM_RUN=0
> >
> > +##
> > +## Build code for the fallback boot
> > +##
> > +default HAVE_FALLBACK_BOOT=1
> >
> > +##
> > +## no MP table
> > +##
> > +default HAVE_MP_TABLE=0
> >
> > +##
> > +## Build code to reset the motherboard from linuxBIOS
> > +##
> > +default HAVE_HARD_RESET=0
> >
> > +## Delay timer options
> > +##
> > +default CONFIG_UDELAY_IO=1
>
> This is a change from the DB800 target:
>
> -default CONFIG_UDELAY_TSC=1
>  -default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
>  +default CONFIG_UDELAY_IO=1
>
> No TSC or TIMER2 on Geode boards?

With CONFIG_UDELAY_TSC and CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
options boot-up occurs at 2 seconds longer.
> > +##
> > +## Build code to export a programmable irq routing table
> > +##
> > +default HAVE_PIRQ_TABLE=1
> > +default IRQ_SLOT_COUNT=9
> > +default PIRQ_ROUTE=1
> > +#object irq_tables.o
> >
> > +##
> > +## Build code to export a CMOS option table
> > +##
> > +default HAVE_OPTION_TABLE=0
> >
> > +###
> > +### LinuxBIOS layout values
> > +###
> >
> > +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
> > +default ROM_IMAGE_SIZE = 65536
> > +default FALLBACK_SIZE = 131072
> >
> > +##
> > +## enable CACHE_AS_RAM specifics
> > +##
> > +default USE_DCACHE_RAM=1
> > +default DCACHE_RAM_BASE=0xc8000
> > +default DCACHE_RAM_SIZE=0x08000
> >
> > +##
> > +## Use a small 8K stack
> > +##
> > +default STACK_SIZE=0x2000
> >
> > +##
> > +## Use a small 16K heap
> > +##
> > +default HEAP_SIZE=0x4000
> >
> > +##
> > +## Only use the option table in a normal image
> > +##
> > +#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
> > +default USE_OPTION_TABLE = 0
> >
> > +default _RAMBASE = 0x00004000
> >
> > +default CONFIG_ROM_PAYLOAD = 1
> >
> > +##
> > +## The default compiler
> > +##
> > +default CROSS_COMPILE=""
> > +default CC="$(CROSS_COMPILE)gcc -m32"
> > +default HOSTCC="gcc"
> >
> > +##
> > +## The Serial Console
> > +##
> >
> > +# To Enable the Serial Console
> > +default CONFIG_CONSOLE_SERIAL8250=1
> >
> > +## Select the serial console baud rate
> > +default TTYS0_BAUD=115200
> > +#default TTYS0_BAUD=57600
> > +#default TTYS0_BAUD=38400
> > +#default TTYS0_BAUD=19200
> > +#default TTYS0_BAUD=9600
> > +#default TTYS0_BAUD=4800
> > +#default TTYS0_BAUD=2400
> > +#default TTYS0_BAUD=1200
> >
> > +# Select the serial console base port
> > +default TTYS0_BASE=0x3f8
> >
> > +# Select the serial protocol
> > +# This defaults to 8 data bits, 1 stop bit, and no parity
> > +default TTYS0_LCS=0x3
> >
> > +##
> > +### Select the linuxBIOS loglevel
> > +##
> > +## EMERG      1   system is unusable
> > +## ALERT      2   action must be taken immediately
> > +## CRIT       3   critical conditions
> > +## ERR        4   error conditions
> > +## WARNING    5   warning conditions
> > +## NOTICE     6   normal but significant condition
> > +## INFO       7   informational
> > +## DEBUG      8   debug-level messages
> > +## SPEW       9   Way too many details
> >
> > +## Request this level of debugging output
> > +default  DEFAULT_CONSOLE_LOGLEVEL=8
> > +## At a maximum only compile in this level of debugging
> > +default  MAXIMUM_CONSOLE_LOGLEVEL=8
> >
> > +end
> >
> > diff -Nru LinuxBIOSv2-2986/targets/iei/pcisa-lx/Config.lb LinuxBIOSv2-2986-lx/targets/iei/pcisa-lx/Config.lb
> > --- LinuxBIOSv2-2986/targets/iei/pcisa-lx/Config.lb   1970-01-01 05:00:00.000000000 +0500
> > +++ LinuxBIOSv2-2986-lx/targets/iei/pcisa-lx/Config.lb        2007-11-26 10:13:13.000000000 +0500
> > @@ -0,0 +1,43 @@
> > +##
> > +## This file is part of the LinuxBIOS project.
> > +##
> > +## Copyright (C) 2007 Nikolay Petukhov 
> > +##
> > +## This program is free software; you can redistribute it and/or modify
> > +## it under the terms of the GNU General Public License as published by
> > +## the Free Software Foundation; either version 2 of the License, or
> > +## (at your option) any later version.
> > +##
> > +## This program is distributed in the hope that it will be useful,
> > +## but WITHOUT ANY WARRANTY; without even the implied warranty of
> > +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > +## GNU General Public License for more details.
> > +##
> > +## You should have received a copy of the GNU General Public License
> > +## along with this program; if not, write to the Free Software
> > +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
> > +##
> >
> > +target pcisa-lx
> > +mainboard iei/pcisa-lx
> >
> > +option CONFIG_COMPRESS=0
> > +option CONFIG_PRECOMPRESSED_PAYLOAD=0
> > +option CONFIG_COMPRESSED_PAYLOAD_NRV2B=0
> > +option CONFIG_COMPRESSED_PAYLOAD_LZMA=0
> >
> > +# Leave 36k for VSA.
> > +option ROM_SIZE=512*1024-36*1024
> > +option FALLBACK_SIZE=ROM_SIZE
> >
> > +option DEFAULT_CONSOLE_LOGLEVEL = 0
> > +option MAXIMUM_CONSOLE_LOGLEVEL = 0
> >
> > +romimage "fallback"
> > option USE_FALLBACK_IMAGE=1
> > option ROM_IMAGE_SIZE=96*1024
> > option LINUXBIOS_EXTRA_VERSION=".0Fallback"
> > payload ../../payload.elf
> >
> > +end
> >
> > +buildrom ./pcisa-lx.rom ROM_SIZE "fallback"
>
> Keep this "./linuxbios.rom" please, we do that will almost all boards
> and it's a good thing IMO.

OK.
> HTH, Uwe.
>
> http://www.hermann-uwe.de  | http://www.holsham-traders.de
> http://www.crazy-hacks.org | http://www.unmaintained-free-software.org