[v2] r4625 - trunk/coreboot-v2/src/southbridge/via/vt8237r

Author: ruik
Date: 2009-09-01 17:29:12 +0200 (Tue, 01 Sep 2009)
New Revision: 4625

Modified:
   trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237_ctrl.c
Log:
As more users of Asus M2V-MX SE emerged. Here is long pending patch I wanted to
write. It boots the SB/NB V-link performance to full duplex 533MB/s. (in fact x2
for FDX)

The default was 266MB/s but half duplex only. If you encourage any stability
issues we need to look into fine tuning the bus. The values are VIA recommended.

Signed-off-by: Rudolf Marek 
Acked-by: Stefan Reinauer

Modified: trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237_ctrl.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237_ctrl.c	2009-09-01 10:03:01 UTC (rev 4624)
+++ trunk/coreboot-v2/src/southbridge/via/vt8237r/vt8237_ctrl.c	2009-09-01 15:29:12 UTC (rev 4625)
@@ -94,6 +94,9 @@
  * V-Link CKG Control				 0xb0  0x05  0x05  0x06  0x03
  * V-Link CKG Control				 0xb1  0x05  0x05  0x01  0x03
  */
+
+/* we setup 533MB/s mode full duplex */
+
 static void vt8237s_vlink_init(struct device *dev)
 {
    u8 reg;
@@ -114,24 +117,47 @@
     * and VT8251) a different init code is required.
     */

+	/* disable auto disconnect */
+	reg = pci_read_config8(devfun7, 0x42);
+	reg &= ~0x4;
+	pci_write_config8(devfun7, 0x42, reg);
+
+	/* NB part setup */
    pci_write_config8(devfun7, 0xb5, 0x66);
    pci_write_config8(devfun7, 0xb6, 0x66);
-	pci_write_config8(devfun7, 0xb7, 0x65);
+	pci_write_config8(devfun7, 0xb7, 0x64);

reg = pci_read_config8(devfun7, 0xb4);
    reg |= 0x1;
+	reg &= ~0x10;
    pci_write_config8(devfun7, 0xb4, reg);

-	pci_write_config8(dev, 0xb9, 0x68);
+	pci_write_config8(devfun7, 0xb0, 0x6);
+	pci_write_config8(devfun7, 0xb1, 0x1);
+
+	/* SB part setup */
+	pci_write_config8(dev, 0xb7, 0x60);
+	pci_write_config8(dev, 0xb9, 0x88);
    pci_write_config8(dev, 0xba, 0x88);
    pci_write_config8(dev, 0xbb, 0x89);

reg = pci_read_config8(dev, 0xbd);
    reg |= 0x3;
+	reg &= ~0x4;
    pci_write_config8(dev, 0xbd, reg);

-	/* Program V-link 8X 8bit full duplex, parity disabled. FIXME. */
-	pci_write_config8(dev, 0x48, 0x13);
+	reg = pci_read_config8(dev, 0xbc);
+	reg &= ~0x7;
+	pci_write_config8(dev, 0xbc, reg);
+
+	/* Program V-link 8X 8bit full duplex, parity enabled.  */
+	pci_write_config8(dev, 0x48, 0x23 | 0x80);
+
+	/* enable auto disconnect, for STPGNT and HALT */
+	reg = pci_read_config8(devfun7, 0x42);
+	reg |= 0x7;
+	pci_write_config8(devfun7, 0x42, reg);
+
 }

static void ctrl_enable(struct device *dev)
@@ -158,8 +184,7 @@
    device_t devsb = dev_find_device(PCI_VENDOR_ID_VIA,
    				 PCI_DEVICE_ID_VIA_VT8237S_LPC, 0);
    if (devsb) {
-		/* FIXME: Skip v-link setup for now. */
-//              vt8237s_vlink_init(dev);
+		vt8237s_vlink_init(dev);
    }

/* Configure PCI1 and copy mirror registers from D0F3. */