Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
Hi Michal,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
Do you have some coreboot/FSP logging?
Best regards, Frans Hendriks Eltan B.V.
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot@coreboot.org Cc: Piotr Król piotr.krol@3mdeb.com Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
_______________________________________________ coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org
Frans Hendriks wrote:
Hi Michal,
Hi Frans,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
These are settings I use in devicetree.cb:
register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB register "PcdMrcInitMmioSize" = "0x0800" register "PcdMrcInitSpdAddr1" = "0xa0" register "PcdMrcInitSpdAddr2" = "0xa2" register "PcdIgdDvmt50PreAlloc" = "1" register "PcdApertureSize" = "2" register "PcdGttSize" = "1" register "PcdDvfsEnable" = "0" register "PcdCaMirrorEn" = "1"
Secondly, using common Intel SoC SMBus block implementation, I retrieve SPD from DIMM and pass it to PcdMemorySpdPtr. Then setting PcdMemChannel0Config to 1 (soldered down memory) and PcdMemChannel0Config to 2 (DIMM disabled, because only the first channel is populated). PcdMemoryTypeEnable is left the default to 0 (DDR3) which should be correct.
Do you have some coreboot/FSP logging?
Here are the logs from Celeron J3160 (I have applied few of Your patches locally, C_ENV_BOOTBLOCK and FSP MR2 support):
1. Using FSP MR2:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 4cc00 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: BSWSBFSP FSP Header Version: 2 FSP Revision: 1.1.4.1 FSP Entry Points: 0xfff20000: Image Base 0xfff6baa8: TempRamInit 0xfff6bc01: FspInit 0xfff6bc0f: MemoryInit 0xfff6bc16: TempRamExit 0xfff6bc1d: SiliconInit 0xfff6bc08: NotifyPhase 0xfff6cc00: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff6452c UPD Data: 0xfff63494 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6bc0f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
2. Using FSP MR1:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 48800 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: $BSWFSP$ FSP Header Version: 2 FSP Revision: 1.1.2.0 FSP Entry Points: 0xfff20000: Image Base 0xfff676a8: TempRamInit 0xfff67801: FspInit 0xfff6780f: MemoryInit 0xfff67816: TempRamExit 0xfff6781d: SiliconInit 0xfff67808: NotifyPhase 0xfff68800: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff4a39c UPD Data: 0xfff4a3b0 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6780f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
After the post code 0x92 platform seems to not going any further. The dump is from the serial port on SuperIO.
Best regards, Frans Hendriks Eltan B.V.
Thank You in advance.
Best regards, Michał
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot(a)coreboot.org Cc: Piotr Król <piotr.krol(a)3mdeb.com> Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
coreboot mailing list -- coreboot(a)coreboot.org To unsubscribe send an email to coreboot-leave(a)coreboot.org
Hi Frans,
These are settings I use in devicetree.cb:
register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB register "PcdMrcInitMmioSize" = "0x0800" register "PcdMrcInitSpdAddr1" = "0xa0" register "PcdMrcInitSpdAddr2" = "0xa2" register "PcdIgdDvmt50PreAlloc" = "1" register "PcdApertureSize" = "2" register "PcdGttSize" = "1" register "PcdDvfsEnable" = "0" register "PcdCaMirrorEn" = "1"
Secondly, using common Intel SoC SMBus block implementation, I retrieve SPD from DIMM and pass it to PcdMemorySpdPtr. Then setting PcdMemChannel0Config to 1 (soldered down memory) and PcdMemChannel0Config to 2 (DIMM disabled, because only first channel is populated). PcdMemoryTypeEnable is left default to 0 (DDR3) which should be correct.
Here are the logs from Celeron J3160 (I have applied few of Your patches locally, C_ENV_BOOTBLOCK and FSP MR2 support):
1. Using FSP MR2:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 4cc00 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: BSWSBFSP FSP Header Version: 2 FSP Revision: 1.1.4.1 FSP Entry Points: 0xfff20000: Image Base 0xfff6baa8: TempRamInit 0xfff6bc01: FspInit 0xfff6bc0f: MemoryInit 0xfff6bc16: TempRamExit 0xfff6bc1d: SiliconInit 0xfff6bc08: NotifyPhase 0xfff6cc00: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff6452c UPD Data: 0xfff63494 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6bc0f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
2. Using FSP MR1:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 48800 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: $BSWFSP$ FSP Header Version: 2 FSP Revision: 1.1.2.0 FSP Entry Points: 0xfff20000: Image Base 0xfff676a8: TempRamInit 0xfff67801: FspInit 0xfff6780f: MemoryInit 0xfff67816: TempRamExit 0xfff6781d: SiliconInit 0xfff67808: NotifyPhase 0xfff68800: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff4a39c UPD Data: 0xfff4a3b0 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6780f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
After the post code 0x92 platform seems to not going any further. The dump is from serial port on SuperIO.
Thank You in advance.
Best regards, Michał
On 29.01.2019 10:12, Frans Hendriks wrote:
Hi Michal,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
Do you have some coreboot/FSP logging?
Best regards, Frans Hendriks Eltan B.V.
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot@coreboot.org Cc: Piotr Król piotr.krol@3mdeb.com Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org _______________________________________________ coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org
Hi Michal,
Your logging seems to be correct. Any different behavior when specifying channel 0 as SPD and have FSP using DIMM spd data?
Another suggestion is using debug version of FSP.
Best regards, Frans
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: dinsdag 29 januari 2019 11:22 To: coreboot@coreboot.org Subject: [coreboot] Re: Braswell FPS memory init problems
Hi Frans,
These are settings I use in devicetree.cb:
register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB register "PcdMrcInitMmioSize" = "0x0800" register "PcdMrcInitSpdAddr1" = "0xa0" register "PcdMrcInitSpdAddr2" = "0xa2" register "PcdIgdDvmt50PreAlloc" = "1" register "PcdApertureSize" = "2" register "PcdGttSize" = "1" register "PcdDvfsEnable" = "0" register "PcdCaMirrorEn" = "1"
Secondly, using common Intel SoC SMBus block implementation, I retrieve SPD from DIMM and pass it to PcdMemorySpdPtr. Then setting PcdMemChannel0Config to 1 (soldered down memory) and PcdMemChannel0Config to 2 (DIMM disabled, because only first channel is populated). PcdMemoryTypeEnable is left default to 0 (DDR3) which should be correct.
Here are the logs from Celeron J3160 (I have applied few of Your patches locally, C_ENV_BOOTBLOCK and FSP MR2 support):
1. Using FSP MR2:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 4cc00 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: BSWSBFSP FSP Header Version: 2 FSP Revision: 1.1.4.1 FSP Entry Points: 0xfff20000: Image Base 0xfff6baa8: TempRamInit 0xfff6bc01: FspInit 0xfff6bc0f: MemoryInit 0xfff6bc16: TempRamExit 0xfff6bc1d: SiliconInit 0xfff6bc08: NotifyPhase 0xfff6cc00: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff6452c UPD Data: 0xfff63494 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6bc0f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
2. Using FSP MR1:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 48800 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: $BSWFSP$ FSP Header Version: 2 FSP Revision: 1.1.2.0 FSP Entry Points: 0xfff20000: Image Base 0xfff676a8: TempRamInit 0xfff67801: FspInit 0xfff6780f: MemoryInit 0xfff67816: TempRamExit 0xfff6781d: SiliconInit 0xfff67808: NotifyPhase 0xfff68800: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff4a39c UPD Data: 0xfff4a3b0 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6780f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
After the post code 0x92 platform seems to not going any further. The dump is from serial port on SuperIO.
Thank You in advance.
Best regards, Michał
On 29.01.2019 10:12, Frans Hendriks wrote:
Hi Michal,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
Do you have some coreboot/FSP logging?
Best regards, Frans Hendriks Eltan B.V.
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot@coreboot.org Cc: Piotr Król piotr.krol@3mdeb.com Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org _______________________________________________ coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org
Hi Frans,
Thank You for response.
Yes, I have also tried setting Channel Config to 0 (DIMM installed), but it does not work either. I have also been playing with CA mirroring and DVFS, but results are the same all the time.
Debug FSP? Is such binary available anywhere? Could You point me please where to get it?
Best regards, Michał
On 01.02.2019 11:38, Frans Hendriks wrote:
Hi Michal,
Your logging seems to be correct. Any different behavior when specifying channel 0 as SPD and have FSP using DIMM spd data?
Another suggestion is using debug version of FSP.
Best regards, Frans
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: dinsdag 29 januari 2019 11:22 To: coreboot@coreboot.org Subject: [coreboot] Re: Braswell FPS memory init problems
Hi Frans,
These are settings I use in devicetree.cb:
register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB register "PcdMrcInitMmioSize" = "0x0800" register "PcdMrcInitSpdAddr1" = "0xa0" register "PcdMrcInitSpdAddr2" = "0xa2" register "PcdIgdDvmt50PreAlloc" = "1" register "PcdApertureSize" = "2" register "PcdGttSize" = "1" register "PcdDvfsEnable" = "0" register "PcdCaMirrorEn" = "1"
Secondly, using common Intel SoC SMBus block implementation, I retrieve SPD from DIMM and pass it to PcdMemorySpdPtr. Then setting PcdMemChannel0Config to 1 (soldered down memory) and PcdMemChannel0Config to 2 (DIMM disabled, because only first channel is populated). PcdMemoryTypeEnable is left default to 0 (DDR3) which should be correct.
Here are the logs from Celeron J3160 (I have applied few of Your patches locally, C_ENV_BOOTBLOCK and FSP MR2 support):
- Using FSP MR2:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 4cc00 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: BSWSBFSP FSP Header Version: 2 FSP Revision: 1.1.4.1 FSP Entry Points: 0xfff20000: Image Base 0xfff6baa8: TempRamInit 0xfff6bc01: FspInit 0xfff6bc0f: MemoryInit 0xfff6bc16: TempRamExit 0xfff6bc1d: SiliconInit 0xfff6bc08: NotifyPhase 0xfff6cc00: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff6452c UPD Data: 0xfff63494 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6bc0f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
- Using FSP MR1:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 48800 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: $BSWFSP$ FSP Header Version: 2 FSP Revision: 1.1.2.0 FSP Entry Points: 0xfff20000: Image Base 0xfff676a8: TempRamInit 0xfff67801: FspInit 0xfff6780f: MemoryInit 0xfff67816: TempRamExit 0xfff6781d: SiliconInit 0xfff67808: NotifyPhase 0xfff68800: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff4a39c UPD Data: 0xfff4a3b0 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6780f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
After the post code 0x92 platform seems to not going any further. The dump is from serial port on SuperIO.
Thank You in advance.
Best regards, Michał
On 29.01.2019 10:12, Frans Hendriks wrote:
Hi Michal,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
Do you have some coreboot/FSP logging?
Best regards, Frans Hendriks Eltan B.V.
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot@coreboot.org Cc: Piotr Król piotr.krol@3mdeb.com Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org _______________________________________________ coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org
Hi Michal,
In coreboot 3rdparty package release version is available only.
The FSP debug is not available in public.
I can't help you with FSP debug in this public community, due too (Intel) license restrictions. If interested in assistance, you can contact us for engineering services.
Best regards, Frans
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: vrijdag 1 februari 2019 11:47 To: coreboot@coreboot.org Cc: Frans Hendriks fhendriks@eltan.com Subject: Re: [coreboot] Re: Braswell FPS memory init problems
Hi Frans,
Thank You for response.
Yes, I have also tried setting Channel Config to 0 (DIMM installed), but it does not work either. I have also been playing with CA mirroring and DVFS, but results are the same all the time.
Debug FSP? Is such binary available anywhere? Could You point me please where to get it?
Best regards, Michał
On 01.02.2019 11:38, Frans Hendriks wrote:
Hi Michal,
Your logging seems to be correct. Any different behavior when specifying channel 0 as SPD and have FSP using DIMM spd data?
Another suggestion is using debug version of FSP.
Best regards, Frans
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: dinsdag 29 januari 2019 11:22 To: coreboot@coreboot.org Subject: [coreboot] Re: Braswell FPS memory init problems
Hi Frans,
These are settings I use in devicetree.cb:
register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB register "PcdMrcInitMmioSize" = "0x0800" register "PcdMrcInitSpdAddr1" = "0xa0" register "PcdMrcInitSpdAddr2" = "0xa2" register "PcdIgdDvmt50PreAlloc" = "1" register "PcdApertureSize" = "2" register "PcdGttSize" = "1" register "PcdDvfsEnable" = "0" register "PcdCaMirrorEn" = "1"
Secondly, using common Intel SoC SMBus block implementation, I retrieve SPD from DIMM and pass it to PcdMemorySpdPtr. Then setting PcdMemChannel0Config to 1 (soldered down memory) and PcdMemChannel0Config to 2 (DIMM disabled, because only first channel is populated). PcdMemoryTypeEnable is left default to 0 (DDR3) which should be correct.
Here are the logs from Celeron J3160 (I have applied few of Your patches locally, C_ENV_BOOTBLOCK and FSP MR2 support):
- Using FSP MR2:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 4cc00 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: BSWSBFSP FSP Header Version: 2 FSP Revision: 1.1.4.1 FSP Entry Points: 0xfff20000: Image Base 0xfff6baa8: TempRamInit 0xfff6bc01: FspInit 0xfff6bc0f: MemoryInit 0xfff6bc16: TempRamExit 0xfff6bc1d: SiliconInit 0xfff6bc08: NotifyPhase 0xfff6cc00: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff6452c UPD Data: 0xfff63494 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6bc0f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
- Using FSP MR1:
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 bootblock starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fallback/romstage' CBFS: Found @ offset 80 size 9564
coreboot-4.9-312-gc316fc82b8 Sat Jan 26 19:00:59 UTC 2019 romstage starting... CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'fsp.bin' CBFS: Found @ offset 3fffc0 size 48800 POST: 0x30 CBFS @ 320000 size 4e0000 CBFS: 'Master Header Locator' located CBFS at [320000:800000) CBFS: Locating 'cpu_microcode_blob.bin' CBFS: Found @ offset 482780 size 44800 microcode: sig=0x406c4 pf=0x1 revision=0x410 CONFIG_MMCONF_BASE_ADDRESS: 0xe0000000 Using FSP 1.1 FSP_INFO_HEADER: fff20094 FSP Signature: $BSWFSP$ FSP Header Version: 2 FSP Revision: 1.1.2.0 FSP Entry Points: 0xfff20000: Image Base 0xfff676a8: TempRamInit 0xfff67801: FspInit 0xfff6780f: MemoryInit 0xfff67816: TempRamExit 0xfff6781d: SiliconInit 0xfff67808: NotifyPhase 0xfff68800: Image End pm1_sts: 0100 pm1_en: 0000 pm1_cnt: 00000000 gpe0_sts: 00000000 gpe0_en: 00000000 tco_sts: 00000000 prsts: 00040910 gen_pmcon1: 00245208 gen_pmcon2: 00000000 prev_sleep_state 5 SPD @ 0x50 SPD: module type is DDR3 SPD: module part is M471B5273DH0-YK0 SPD: banks 8, ranks 2, rows 15, columns 10, density 2048 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 4096 MB (per channel) POST: 0x32 POST: 0x33 FMAP: Found "FLASH" version 1.1 at 300000. FMAP: base = ff800000 size = 800000 #areas = 4 FMAP: area RW_MRC_CACHE found @ 310000 (65536 bytes) MRC: no data in 'RW_MRC_CACHE' No MRC cache found. POST: 0x34 VPD Data: 0xfff4a39c UPD Data: 0xfff4a3b0 Updating UPD values for MemoryInit POST: 0x36 UPD values for MemoryInit: 0x0004 --> 0x0008: PcdMrcInitTsegSize 0x0800: PcdMrcInitMmioSize 0xa0: PcdMrcInitSpdAddr1 0xa2: PcdMrcInitSpdAddr2 0x00 --> 0x01: PcdMemChannel0Config 0x00 --> 0x02: PcdMemChannel1Config 0x00000000 --> 0xfef02ea0: PcdMemorySpdPtr 0x01: PcdIgdDvmt50PreAlloc 0x02: PcdApertureSize 0x01: PcdGttSize 0x00: PcdLegacySegDecode 0x01 --> 0x00: PcdDvfsEnable Calling FspMemoryInit: 0xfff6780f 0x00000000: NvsBufferPtr 0xfef01de4: RtBufferPtr 0xfef01d8c: HobListPtr POST: 0x92
After the post code 0x92 platform seems to not going any further. The dump is from serial port on SuperIO.
Thank You in advance.
Best regards, Michał
On 29.01.2019 10:12, Frans Hendriks wrote:
Hi Michal,
We have implemented coreboot on Braswell SoC (Pentium N3170) using SPD.
Did you verify the UDP fields: PcdMemoryTypeEnable, PcdMemorySpdPtr PcdMemChannel0Config and PcdMemChannel1Config?
Do you have some coreboot/FSP logging?
Best regards, Frans Hendriks Eltan B.V.
-----Original Message----- From: Michal Zygowski [mailto:michal.zygowski@3mdeb.com] Sent: maandag 28 januari 2019 15:48 To: coreboot@coreboot.org Cc: Piotr Król piotr.krol@3mdeb.com Subject: [coreboot] Braswell FPS memory init problems
Dear coreboot community,
I am experiencing problems with FSP Memory Init on Braswell SoCs. FSP Memory Init is not returning. I have following processors that fail: Celeron J3060 and Celeron J3160; both have the same issue.
The platform has 1 SODIMM module on channel 0. I am feeding the UPD header with correct SPD, but still no luck. I have also tried FSP MR1 and MR2, but nothing works.
Is anyone here more experienced with Braswell platforms? Could You give me some advices?
Best regards,
-- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org _______________________________________________ coreboot mailing list -- coreboot@coreboot.org To unsubscribe send an email to coreboot-leave@coreboot.org
-- -- Michał Żygowski Embedded Systems Engineer http://3mdeb.com | @3mdeb_com
-
Frans Hendriks -
Michal Zygowski -
michal.zygowski＠3mdeb.com