Re: [LinuxBIOS] DK8-HTX FILO IDE timeout

[Lu, Yinghai]

Please decrease that LOG level to 8.

And you should got
PCI:00:07.1 init
IDE1
IDE0

in your log output.

If it still doesn't work, hardcode amd8111_ide.c to enable ide device
directly.

YH

-----Original Message-----
From: Chris Stillo [mailto:[e-mail]] 
Sent: Thursday, September 21, 2006 3:57 PM
To: Lu, Yinghai
Cc: [e-mail]; Stefan Reinauer
Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout

I added these lines and recompiled, but it still does not work. Maybe 
there is still something else missing? I will re-check PCI configuration

in MB's Config.lb, must still be an error in there...
> Check serengeti_leopard or tyan/s2881 etc  MB Config.lb to add two

lines
> to enable your IDE devices.
>
> YH
>
> -----Original Message-----
> From: Chris Stillo [mailto:[e-mail]] 
> Sent: Thursday, September 21, 2006 3:24 PM
> To: Lu, Yinghai
> Cc: [e-mail]; Stefan Reinauer
> Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
>
> No, those lines are not there in MB Config... I serach for 'ide0' and 
> find nothing... where exactly do they go in the file?
> > Please check if you have register "ide0_enable"="1"  in MB Config.lb
> >             chip southbridge/amd/amd8111
> >                 # this "device pci 0.0" is the parent the next

one
> >                 # PCI bridge
> >                 device pci 0.0 on
> >                     device pci 0.0 on end
> >                     device pci 0.1 on end
> >                     device pci 0.2 on end
> >                     device pci 1.0 off end
> >                 end
> >
> > .....
> >    		register "ide0_enable"="1" 
> >    		register "ide1_enable"="1"
> >
> > ....
> >
> > YH
> >
> > -----Original Message-----
> > From: Chris Stillo [mailto:[e-mail]] 
> > Sent: Thursday, September 21, 2006 3:13 PM
> > To: Lu, Yinghai
> > Cc: [e-mail]; Stefan Reinauer
> > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >
> > Hi YH,
> >
> > I checked  MB Config.lb as you suggested. From lspci I know my IDE 
> > controller is here:
> >
> > 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev
> > 03)
> >
> > Yet I do not see 00:07.1 mentioned in the MB Config.lb in the 
> > southbridge section. Maybe this is the issue... , maybe IDE is not 
> > configured since SATA would be mostly used? (My SATA drive is 
> > recognized, but has XP on it :| -- it is presenlty disconnected).
> >
> > I also included AMD 3111 chip.h below, which looks ok. I have not 
> > modified either file at all.
> > If you see an error please let me know...
> >
> > Thanks,
> > Chris
> > > Check your MB Config.lb to see if amd8111 is under correct 0.18.0
> >
> > link.
> > >
> >
> > # config for Iwill/DK8HTX
> > chip northbridge/amd/amdk8/root_complex
> >     device pci_domain 0 on
> >         chip northbridge/amd/amdk8
> >             device pci 18.0 on # LDT 0
> >                 chip southbridge/amd/amd8131
> >                     device pci 0.0 on end
> >                     device pci 0.1 on end
> >                     device pci 1.0 on end
> >                     device pci 1.1 on end
> >                 end
> >                 chip southbridge/amd/amd8111
> >                     # this "device pci 0.0" is the parent the next

one
> >                 # PCI bridge
> >                 device pci 0.0 on
> >                     device pci 0.0 on end
> >                     device pci 0.1 on end
> >                     device pci 0.2 on end
> >                     device pci 1.0 off end
> >                 end

------------------------------------------------------------------------
> > /LinuxBIOSv2/src/southbridge/amd/amd8111
> > bash-3.1$ more chip.h
> >
> > #ifndef AMD8111_CHIP_H
> > #define AMD8111_CHIP_H
> >
> > struct southbridge_amd_amd8111_config
> > {
> >         unsigned int ide0_enable : 1;
> >         unsigned int ide1_enable : 1;
> >         unsigned int phy_lowreset : 1;
> > };
> >
> > struct chip_operations;
> > extern struct chip_operations southbridge_amd_amd8111_ops;
> >
> > #endif /* AMD8111_CHIP_H */
> > > YH

[LinuxBIOS] DK8-HTX FILO IDE timeout

[Chris Stillo]

YH,

Thanks for the suggestion. I decreased LOG level to 8, and did not see 
"IDE1 IDE0 PCI: 00:07.1 init" in the LOG. Then I hacked amd8111_ide.c 
now I see "IDE1 IDE0 PCI: *01:04.3* init" in the log. And still the IDE 
timeout happens in FILO... but this is not suprising since it looks like 
the wrong PCI address is assigned to IDE(?) If so, do you know how to 
correct this?

Thanks,
Chris
> Please decrease that LOG level to 8.
>
> And you should got
> PCI:00:07.1 init
> IDE1
> IDE0
>
> in your log output.
>
> If it still doesn't work, hardcode amd8111_ide.c to enable ide device
> directly.
>
> YH
>
> -----Original Message-----
> From: Chris Stillo [mailto:[e-mail]] 
> Sent: Thursday, September 21, 2006 3:57 PM
> To: Lu, Yinghai
> Cc: [e-mail]; Stefan Reinauer
> Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
>
> I added these lines and recompiled, but it still does not work. Maybe 
> there is still something else missing? I will re-check PCI configuration
>
> in MB's Config.lb, must still be an error in there...
> > Check serengeti_leopard or tyan/s2881 etc  MB Config.lb to add two
>
> lines
> > to enable your IDE devices.
> >
> > YH
> >
> > -----Original Message-----
> > From: Chris Stillo [mailto:[e-mail]] 
> > Sent: Thursday, September 21, 2006 3:24 PM
> > To: Lu, Yinghai
> > Cc: [e-mail]; Stefan Reinauer
> > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >
> > No, those lines are not there in MB Config... I serach for 'ide0' and 
> > find nothing... where exactly do they go in the file?
> > > Please check if you have register "ide0_enable"="1"  in MB Config.lb
> > >             chip southbridge/amd/amd8111
> > >                 # this "device pci 0.0" is the parent the next
>
> one
> > >                 # PCI bridge
> > >                 device pci 0.0 on
> > >                     device pci 0.0 on end
> > >                     device pci 0.1 on end
> > >                     device pci 0.2 on end
> > >                     device pci 1.0 off end
> > >                 end
> > >
> > > .....
> > >    		register "ide0_enable"="1" 
> > >    		register "ide1_enable"="1"
> > >
> > > ....
> > >
> > > YH
> > >
> > > -----Original Message-----
> > > From: Chris Stillo [mailto:[e-mail]] 
> > > Sent: Thursday, September 21, 2006 3:13 PM
> > > To: Lu, Yinghai
> > > Cc: [e-mail]; Stefan Reinauer
> > > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> > >
> > > Hi YH,
> > >
> > > I checked  MB Config.lb as you suggested. From lspci I know my IDE 
> > > controller is here:
> > >
> > > 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev
> > > 03)
> > >
> > > Yet I do not see 00:07.1 mentioned in the MB Config.lb in the 
> > > southbridge section. Maybe this is the issue... , maybe IDE is not 
> > > configured since SATA would be mostly used? (My SATA drive is 
> > > recognized, but has XP on it :| -- it is presenlty disconnected).
> > >
> > > I also included AMD 3111 chip.h below, which looks ok. I have not 
> > > modified either file at all.
> > > If you see an error please let me know...
> > >
> > > Thanks,
> > > Chris
> > > > Check your MB Config.lb to see if amd8111 is under correct 0.18.0
> > >
> > > link.
> > > >
> > >
> > > # config for Iwill/DK8HTX
> > > chip northbridge/amd/amdk8/root_complex
> > >     device pci_domain 0 on
> > >         chip northbridge/amd/amdk8
> > >             device pci 18.0 on # LDT 0
> > >                 chip southbridge/amd/amd8131
> > >                     device pci 0.0 on end
> > >                     device pci 0.1 on end
> > >                     device pci 1.0 on end
> > >                     device pci 1.1 on end
> > >                 end
> > >                 chip southbridge/amd/amd8111
> > >                     # this "device pci 0.0" is the parent the next
>
> one
> > >                 # PCI bridge
> > >                 device pci 0.0 on
> > >                     device pci 0.0 on end
> > >                     device pci 0.1 on end
> > >                     device pci 0.2 on end
> > >                     device pci 1.0 off end
> > >                 end
> > > /LinuxBIOSv2/src/southbridge/amd/amd8111
> > > bash-3.1$ more chip.h
> > >
> > > #ifndef AMD8111_CHIP_H
> > > #define AMD8111_CHIP_H
> > >
> > > struct southbridge_amd_amd8111_config
> > > {
> > >         unsigned int ide0_enable : 1;
> > >         unsigned int ide1_enable : 1;
> > >         unsigned int phy_lowreset : 1;
> > > };
> > >
> > > struct chip_operations;
> > > extern struct chip_operations southbridge_amd_amd8111_ops;
> > >
> > > #endif /* AMD8111_CHIP_H */
> > > > YH

[LinuxBIOS] DK8-HTX FILO IDE timeout

[yhlu]

let me build one image tomorrow.

YH

On 9/21/06, Chris Stillo  wrote:
> YH,
>
> Thanks for the suggestion. I decreased LOG level to 8, and did not see
> "IDE1 IDE0 PCI: 00:07.1 init" in the LOG. Then I hacked amd8111_ide.c
> now I see "IDE1 IDE0 PCI: *01:04.3* init" in the log. And still the IDE
> timeout happens in FILO... but this is not suprising since it looks like
> the wrong PCI address is assigned to IDE(?) If so, do you know how to
> correct this?
>
> Thanks,
> Chris
> > Please decrease that LOG level to 8.
> >
> > And you should got
> > PCI:00:07.1 init
> > IDE1
> > IDE0
> >
> > in your log output.
> >
> > If it still doesn't work, hardcode amd8111_ide.c to enable ide device
> > directly.
> >
> > YH
> >
> > -----Original Message-----
> > From: Chris Stillo [mailto:[e-mail]]
> > Sent: Thursday, September 21, 2006 3:57 PM
> > To: Lu, Yinghai
> > Cc: [e-mail]; Stefan Reinauer
> > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> >
> > I added these lines and recompiled, but it still does not work. Maybe
> > there is still something else missing? I will re-check PCI configuration
> >
> > in MB's Config.lb, must still be an error in there...
> > > Check serengeti_leopard or tyan/s2881 etc  MB Config.lb to add two
> >
> > lines
> > > to enable your IDE devices.
> > >
> > > YH
> > >
> > > -----Original Message-----
> > > From: Chris Stillo [mailto:[e-mail]]
> > > Sent: Thursday, September 21, 2006 3:24 PM
> > > To: Lu, Yinghai
> > > Cc: [e-mail]; Stefan Reinauer
> > > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> > >
> > > No, those lines are not there in MB Config... I serach for 'ide0' and
> > > find nothing... where exactly do they go in the file?
> > > > Please check if you have register "ide0_enable"="1"  in MB Config.lb
> > > >             chip southbridge/amd/amd8111
> > > >                 # this "device pci 0.0" is the parent the next
> >
> > one
> > > >                 # PCI bridge
> > > >                 device pci 0.0 on
> > > >                     device pci 0.0 on end
> > > >                     device pci 0.1 on end
> > > >                     device pci 0.2 on end
> > > >                     device pci 1.0 off end
> > > >                 end
> > > >
> > > > .....
> > > >                     register "ide0_enable"="1"
> > > >                     register "ide1_enable"="1"
> > > >
> > > > ....
> > > >
> > > > YH
> > > >
> > > > -----Original Message-----
> > > > From: Chris Stillo [mailto:[e-mail]]
> > > > Sent: Thursday, September 21, 2006 3:13 PM
> > > > To: Lu, Yinghai
> > > > Cc: [e-mail]; Stefan Reinauer
> > > > Subject: Re: [LinuxBIOS] DK8-HTX FILO IDE timeout
> > > >
> > > > Hi YH,
> > > >
> > > > I checked  MB Config.lb as you suggested. From lspci I know my IDE
> > > > controller is here:
> > > >
> > > > 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev
> > > > 03)
> > > >
> > > > Yet I do not see 00:07.1 mentioned in the MB Config.lb in the
> > > > southbridge section. Maybe this is the issue... , maybe IDE is not
> > > > configured since SATA would be mostly used? (My SATA drive is
> > > > recognized, but has XP on it :| -- it is presenlty disconnected).
> > > >
> > > > I also included AMD 3111 chip.h below, which looks ok. I have not
> > > > modified either file at all.
> > > > If you see an error please let me know...
> > > >
> > > > Thanks,
> > > > Chris
> > > > > Check your MB Config.lb to see if amd8111 is under correct 0.18.0
> > > >
> > > > link.
> > > > >
> > > >
> > > > # config for Iwill/DK8HTX
> > > > chip northbridge/amd/amdk8/root_complex
> > > >     device pci_domain 0 on
> > > >         chip northbridge/amd/amdk8
> > > >             device pci 18.0 on # LDT 0
> > > >                 chip southbridge/amd/amd8131
> > > >                     device pci 0.0 on end
> > > >                     device pci 0.1 on end
> > > >                     device pci 1.0 on end
> > > >                     device pci 1.1 on end
> > > >                 end
> > > >                 chip southbridge/amd/amd8111
> > > >                     # this "device pci 0.0" is the parent the next
> >
> > one
> > > >                 # PCI bridge
> > > >                 device pci 0.0 on
> > > >                     device pci 0.0 on end
> > > >                     device pci 0.1 on end
> > > >                     device pci 0.2 on end
> > > >                     device pci 1.0 off end
> > > >                 end
> > > > /LinuxBIOSv2/src/southbridge/amd/amd8111
> > > > bash-3.1$ more chip.h
> > > >
> > > > #ifndef AMD8111_CHIP_H
> > > > #define AMD8111_CHIP_H
> > > >
> > > > struct southbridge_amd_amd8111_config
> > > > {
> > > >         unsigned int ide0_enable : 1;
> > > >         unsigned int ide1_enable : 1;
> > > >         unsigned int phy_lowreset : 1;
> > > > };
> > > >
> > > > struct chip_operations;
> > > > extern struct chip_operations southbridge_amd_amd8111_ops;
> > > >
> > > > #endif /* AMD8111_CHIP_H */
> > > > > YH