[LinuxBIOS] r520 - in LinuxBIOSv3: . mainboard/adl/msm800sev mainboard/amd/norwich mainboard/artecgroup/dbe61 mainboard/emulation/qemu-x86
Author: uwe Date: 2007-11-26 21:28:21 +0100 (Mon, 26 Nov 2007) New Revision: 520
Modified: LinuxBIOSv3/Kconfig LinuxBIOSv3/README LinuxBIOSv3/Rules.make LinuxBIOSv3/mainboard/adl/msm800sev/initram.c LinuxBIOSv3/mainboard/adl/msm800sev/stage1.c LinuxBIOSv3/mainboard/amd/norwich/initram.c LinuxBIOSv3/mainboard/amd/norwich/stage1.c LinuxBIOSv3/mainboard/artecgroup/dbe61/initram.c LinuxBIOSv3/mainboard/artecgroup/dbe61/stage1.c LinuxBIOSv3/mainboard/emulation/qemu-x86/initram.c LinuxBIOSv3/mainboard/emulation/qemu-x86/stage1.c LinuxBIOSv3/mainboard/emulation/qemu-x86/vga.c Log: Various cleanups and cosmetic fixes.
Signed-off-by: Uwe Hermann uwe@hermann-uwe.de Acked-by: Corey Osgood corey.osgood@gmail.com
Modified: LinuxBIOSv3/Kconfig =================================================================== --- LinuxBIOSv3/Kconfig 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/Kconfig 2007-11-26 20:28:21 UTC (rev 520) @@ -101,20 +101,24 @@ depends EXPERT default n help - Until now, LinuxBIOS has used elf for the payload. There are many problems - this, not least being the inefficiency -- the ELF has to be decompressed to - memory and then the segments have to be copied. Plus, lar can't see the segments - in the elf -- to see all segments, you have to extract the elf and run readelf on it. - There are problems with collisions of the decompressed ELF location in memory - and the segment locations in memory. - Finally, validation of the ELF is done at run time, once you have flashed the - FLASH and rebooted the machine. Boot time is really not the time you want to find - out your ELF payload is broken. - With this option, LinuxBIOS will direct lar to break each elf segment into a LAR - entry. ELF will not be used at all. Note that (for now) LinuxBIOS is backward - compatible -- if you put an ELF payload in, LinuxBIOS can still parse it. We hope - to remove ELF entirely in the future. + Until now, LinuxBIOS has used ELF for the payload. There are many + problems with this, not least being the inefficiency -- the ELF has + to be decompressed to memory and then the segments have to be + copied. Plus, lar can't see the segments in the ELF -- to see all + segments, you have to extract the ELF and run readelf on it.
+ There are problems with collisions of the decompressed ELF + location in memory and the segment locations in memory. + Finally, validation of the ELF is done at run time, once you have + flashed the FLASH and rebooted the machine. Boot time is really + not the time you want to find out your ELF payload is broken. + + With this option, LinuxBIOS will direct lar to break each ELF + segment into a LAR entry. ELF will not be used at all. Note that + (for now) LinuxBIOS is backward compatible -- if you put an ELF + payload in, LinuxBIOS can still parse it. We hope to remove ELF + entirely in the future. + config PAYLOAD_ELF bool "An ELF executable payload file" help
Modified: LinuxBIOSv3/README =================================================================== --- LinuxBIOSv3/README 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/README 2007-11-26 20:28:21 UTC (rev 520) @@ -102,7 +102,7 @@ The 'flashrom' tool is located in util/flashrom where you can build it from source code by typing 'make'. Alternatively, your favorite Linux distribution might ship a 'flashrom' package which provides the 'flashrom' - program in (e.g.) /usr/bin. On Debian GNU/Linux systems you can get + program in (e.g.) /usr/sbin. On Debian GNU/Linux systems you can get the flashrom package via 'apt-get install flashrom'.
Modified: LinuxBIOSv3/Rules.make =================================================================== --- LinuxBIOSv3/Rules.make 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/Rules.make 2007-11-26 20:28:21 UTC (rev 520) @@ -80,7 +80,7 @@
# # RAM initialization code can not be linked at a specific address, -# hence it has to be executed in place position independently. +# hence it has to be executed in place (XIP) position independently. #
$(obj)/%_xip.o: $(src)/%.c
Modified: LinuxBIOSv3/mainboard/adl/msm800sev/initram.c =================================================================== --- LinuxBIOSv3/mainboard/adl/msm800sev/initram.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/adl/msm800sev/initram.c 2007-11-26 20:28:21 UTC (rev 520) @@ -19,6 +19,7 @@ */
#define _MAINOBJECT + #include <types.h> #include <lib.h> #include <console.h> @@ -33,9 +34,11 @@ #include <southbridge/amd/cs5536/cs5536.h> #include <northbridge/amd/geodelx/raminit.h>
-#define MANUALCONF 0 /* Do automatic strapped PLL config */ -#define PLLMSRHI 0x00001490 /* manual settings for the PLL */ +#define MANUALCONF 0 /* Do automatic strapped PLL config. */ + +#define PLLMSRHI 0x00001490 /* Manual settings for the PLL */ #define PLLMSRLO 0x02000030 + #define DIMM0 ((u8) 0xA0) #define DIMM1 ((u8) 0xA2)
@@ -52,10 +55,10 @@ sdram_set_spd_registers(DIMM0, DIMM1); sdram_enable(DIMM0, DIMM1);
- /* Check low memory */ - //ram_check(0x00000000, 640*1024); + /* Check low memory. */ + /* ram_check(0, 640 * 1024); */
- /* Switch from Cache as RAM to real RAM */ + /* Switch from Cache as RAM to real RAM. */ printk(BIOS_SPEW, "Before wbinvd\n"); __asm__("wbinvd\n"); printk(BIOS_SPEW, "After wbinvd\n");
Modified: LinuxBIOSv3/mainboard/adl/msm800sev/stage1.c =================================================================== --- LinuxBIOSv3/mainboard/adl/msm800sev/stage1.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/adl/msm800sev/stage1.c 2007-11-26 20:28:21 UTC (rev 520) @@ -32,10 +32,10 @@ #include <southbridge/amd/cs5536/cs5536.h> #include <superio/winbond/w83627hf/w83627hf.h>
-#define SERIAL_DEV W83627HF_SP1 -#define SERIAL_IOBASE 0x3f8 +#define SERIAL_DEV W83627HF_SP1 +#define SERIAL_IOBASE 0x3f8
-/* printk will not yet output anything */ +/* printk() will not yet output anything. */
void hardware_stage1(void) { @@ -46,9 +46,9 @@
cs5536_stage1();
- /* NOTE: must do this AFTER the early_setup! - * it is counting on some early MSR setup - * for cs5536 + /* + * NOTE: Must do this AFTER the early_setup! It is counting on some + * early MSR setup for the CS5536. */ cs5536_disable_internal_uart(); w83627hf_enable_serial(0x2e, SERIAL_DEV, SERIAL_IOBASE);
Modified: LinuxBIOSv3/mainboard/amd/norwich/initram.c =================================================================== --- LinuxBIOSv3/mainboard/amd/norwich/initram.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/amd/norwich/initram.c 2007-11-26 20:28:21 UTC (rev 520) @@ -31,51 +31,46 @@ #include <amd_geodelx.h> #include <northbridge/amd/geodelx/raminit.h>
-#define MANUALCONF 0 /* Do automatic strapped PLL config */ -#define PLLMSRHI 0x00001490 /* manual settings for the PLL */ +#define MANUALCONF 0 /* Do automatic strapped PLL config. */ + +#define PLLMSRHI 0x00001490 /* Manual settings for the PLL */ #define PLLMSRLO 0x02000030 + #define DIMM0 ((u8) 0xA0) #define DIMM1 ((u8) 0xA2)
- /** - * Place holder in case we ever need it. Since this file is a - * template for other motherboards, we want this here and we want the - * call in the right place. - */ - + * Placeholder in case we ever need it. Since this file is a template for + * other boards, we want this here and we want the call in the right place. + */ static void mb_gpio_init(void) { /* Early mainboard specific GPIO setup */ }
-/** - * main for initram for the amd norwich. It might seem that you - * could somehow do these functions in, e.g., the cpu code, but the - * order of operations and what those operations are is VERY strongly - * mainboard dependent. It's best to leave it in the mainboard code. - */ +/** + * Main for initram for the AMD Norwich. It might seem that you could somehow + * do these functions in, e.g., the CPU code, but the order of operations and + * what those operations are is VERY strongly mainboard dependent. It's best to + * leave it in the mainboard code. + */ int main(void) { - u8 smb_devices[] = { - DIMM0, DIMM1 - }; + u8 smb_devices[] = { DIMM0, DIMM1 };
post_code(POST_START_OF_MAIN);
system_preinit(); - mb_gpio_init(); - pll_reset(MANUALCONF, PLLMSRHI, PLLMSRLO); - cpu_reg_init(0, DIMM0, DIMM1);
sdram_set_registers(); sdram_set_spd_registers(DIMM0, DIMM1); sdram_enable(DIMM0, DIMM1); - /* Check low memory */ - /*ram_check(0x00000000, 640*1024); */
+ /* Check low memory. */ + /* ram_check(0, 640 * 1024); */ + return 0; }
Modified: LinuxBIOSv3/mainboard/amd/norwich/stage1.c =================================================================== --- LinuxBIOSv3/mainboard/amd/norwich/stage1.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/amd/norwich/stage1.c 2007-11-26 20:28:21 UTC (rev 520) @@ -32,16 +32,17 @@ void hardware_stage1(void) { post_code(POST_START_OF_MAIN); + geodelx_msr_init();
cs5536_stage1();
- /* NOTE: must do this AFTER the early_setup! - * it is counting on some early MSR setup - * for cs5536. + /* + * NOTE: Must do this AFTER the early_setup! It is counting on some + * early MSR setup for the CS5536. We do this early for debug. + * Real setup should be done in chipset init via Config.lb. + * + * TODO: Drop Config.lb reference, update comment. */ - /* We do this early for debug. - * real setup should done in chipset init via config.lb - */ cs5536_setup_onchipuart(); }
Modified: LinuxBIOSv3/mainboard/artecgroup/dbe61/initram.c =================================================================== --- LinuxBIOSv3/mainboard/artecgroup/dbe61/initram.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/artecgroup/dbe61/initram.c 2007-11-26 20:28:21 UTC (rev 520) @@ -19,6 +19,7 @@ */
#define _MAINOBJECT + #include <types.h> #include <lib.h> #include <console.h> @@ -31,19 +32,19 @@ #include <southbridge/amd/cs5536/cs5536.h> #include <northbridge/amd/geodelx/raminit.h>
-#define MANUALCONF 0 /* Do automatic strapped PLL config */ -#define PLLMSRHI 0x00001490 /* manual settings for the PLL */ +#define MANUALCONF 0 /* Do automatic strapped PLL config. */ + +#define PLLMSRHI 0x00001490 /* Manual settings for the PLL */ #define PLLMSRLO 0x02000030 + #define DIVIL_LBAR_GPIO 0x5140000c + #define DIMM0 ((u8) 0xA0) #define DIMM1 ((u8) 0xA2)
-/* this is an incredibly mainboard-specific number that has no appropriate place - * outside this file. - */ -#define GPIO_BASE 0x6100 +#define GPIO_BASE 0x6100 /* Mainboard-specific */
-/* empty function to always fail smbus reads */ +/** Empty function to always fail SMBus reads. */ int smbus_read_byte(unsigned device, unsigned address) { return -1; @@ -52,14 +53,17 @@ static void init_gpio(void) { struct msr msr; + printk(BIOS_DEBUG, "Initializing GPIO module...\n");
- // initialize the GPIO LBAR + /* Initialize the GPIO LBAR. */ msr.lo = GPIO_BASE; msr.hi = 0x0000f001; wrmsr(DIVIL_LBAR_GPIO, msr); msr = rdmsr(DIVIL_LBAR_GPIO); - printk(BIOS_DEBUG, "DIVIL_LBAR_GPIO set to 0x%08x 0x%08x\n", msr.hi, msr.lo); + + printk(BIOS_DEBUG, "DIVIL_LBAR_GPIO set to 0x%08x 0x%08x\n", + msr.hi, msr.lo); }
static void sdram_hardwire(void) @@ -67,16 +71,17 @@ /* Total size of DIMM = 2^row address (byte 3) * 2^col address (byte 4) * * component Banks (byte 17) * module banks, side (byte 5) * * width in bits (byte 6,7) - * = Density per side (byte 31) * number of sides (byte 5) */ - /* 1. Initialize GLMC registers base on SPD values, do one DIMM for now */ - struct msr msr; + * = Density per side (byte 31) * number of sides (byte 5) + */
+ /* Initialize GLMC registers based on SPD values, do one DIMM for now. */ + struct msr msr; + msr.hi = 0x10075012; msr.lo = 0x00000040; - - wrmsr(MC_CF07_DATA, msr); //GX3 + wrmsr(MC_CF07_DATA, msr); /* GX3 */
- /* timing and mode ... */ + /* Timing and mode... */
//msr = rdmsr(0x20000019); @@ -109,11 +114,11 @@
static const struct wmsr { u32 reg; - struct msr msr; + struct msr msr; } dbe61_msr[] = { - {.reg = 0x10000020, {.lo = 0xfff80, .hi = 0x20000000}}, + {.reg = 0x10000020, {.lo = 0x00fff80, .hi = 0x20000000}}, {.reg = 0x10000021, {.lo = 0x80fffe0, .hi = 0x20000000}}, - {.reg = 0x40000020, {.lo = 0xfff80, .hi = 0x20000000}}, + {.reg = 0x40000020, {.lo = 0x00fff80, .hi = 0x20000000}}, {.reg = 0x40000021, {.lo = 0x80fffe0, .hi = 0x20000000}}, };
@@ -129,14 +134,15 @@ post_code(POST_START_OF_MAIN);
system_preinit(); - pll_reset(MANUALCONF, PLLMSRHI, PLLMSRLO); - cpu_reg_init(0, DIMM0, DIMM1);
sdram_hardwire(); + /* Check low memory */ - /*ram_check(0x00000000, 640*1024); */ + /* ram_check(0, 640 * 1024); */ + init_gpio(); + return 0; }
Modified: LinuxBIOSv3/mainboard/artecgroup/dbe61/stage1.c =================================================================== --- LinuxBIOSv3/mainboard/artecgroup/dbe61/stage1.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/artecgroup/dbe61/stage1.c 2007-11-26 20:28:21 UTC (rev 520) @@ -34,9 +34,9 @@ u32 reg; struct msr msr; } dbe61_msr[] = { - {.reg = 0x10000020, {.lo = 0xfff80, .hi = 0x20000000}}, + {.reg = 0x10000020, {.lo = 0x00fff80, .hi = 0x20000000}}, {.reg = 0x10000021, {.lo = 0x80fffe0, .hi = 0x20000000}}, - {.reg = 0x40000020, {.lo = 0xfff80, .hi = 0x20000000}}, + {.reg = 0x40000020, {.lo = 0x00fff80, .hi = 0x20000000}}, {.reg = 0x40000021, {.lo = 0x80fffe0, .hi = 0x20000000}}, };
@@ -55,9 +55,9 @@
cs5536_stage1();
- /* NOTE: must do this AFTER the early_setup! - * it is counting on some early MSR setup - * for cs5536. + /* + * NOTE: Must do this AFTER the early_setup! It is counting on some + * early MSR setup for the CS5536. */ cs5536_setup_onchipuart(); }
Modified: LinuxBIOSv3/mainboard/emulation/qemu-x86/initram.c =================================================================== --- LinuxBIOSv3/mainboard/emulation/qemu-x86/initram.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/emulation/qemu-x86/initram.c 2007-11-26 20:28:21 UTC (rev 520) @@ -18,6 +18,7 @@ */
#define _MAINOBJECT + #include <console.h>
int main(void)
Modified: LinuxBIOSv3/mainboard/emulation/qemu-x86/stage1.c =================================================================== --- LinuxBIOSv3/mainboard/emulation/qemu-x86/stage1.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/emulation/qemu-x86/stage1.c 2007-11-26 20:28:21 UTC (rev 520) @@ -17,15 +17,16 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */
-/* printk will not yet output anything */ +/* printk() will not yet output anything. */
/** - * start up hardware needed for stage1 + * Start up hardware needed for stage1. */ void hardware_stage1(void) { - /* Nothing to do for Qemu */ + /* Nothing to do for QEMU. */ } + void disable_car(void) { }
Modified: LinuxBIOSv3/mainboard/emulation/qemu-x86/vga.c =================================================================== --- LinuxBIOSv3/mainboard/emulation/qemu-x86/vga.c 2007-11-26 13:28:52 UTC (rev 519) +++ LinuxBIOSv3/mainboard/emulation/qemu-x86/vga.c 2007-11-26 20:28:21 UTC (rev 520) @@ -32,11 +32,14 @@ struct pc_keyboard conf;
printk(BIOS_INFO, "Init VGA device\n"); + dev->on_mainboard = 1; dev->rom_address = 0xc0000;
- // FIXME - this should be in superio some day - // but since qemu has no superio. + /* + * FIXME: This should be in the Super I/O code some day, + * but since QEMU has no Super I/O... + */ init_pc_keyboard(0x60, 0x64, &conf); }
-
svn＠openbios.org