On Mon, 23 Jan 2017 15:51:16 +0200 Kyösti Mälkki kyosti.malkki@gmail.com wrote:
On Mon, Jan 23, 2017 at 2:41 PM, Maxim Gusev via coreboot < coreboot@coreboot.org> wrote:
Hi Daniel,
Now I have compiled coreboot 4.5 with the SeaBIOS 1.9.3 as a payload and the VGAbios: I am using the Asus EN8600GT as a videocard (PCIe) and I took out the binary here: https://www.techpowerup.com/vgabios/?architecture=& manufacturer=Asus&model=8600+GT&interface=PCI-E&memType=& memSize=256&since=
To my understanding, when using an external graphics card you don't need to extract or put any VGA blobs in. But you need to initialize the PCIe video. Can you provide us with the full config you are using, please? Or did you try my config which I linked in my initial answer? (There, it should be already enabled as far as I remember)
Also I have turned on in console settings "Show POST codes...", but there is nothing works:(
You probably also need POST_DEVICE_PCI_PCIE set in your .config. In menuconfig: "Device to send POST codes to" -> "PCI/PCIe".
As for the serial port: I think this mainboard is not a retail version, but came from ASUS Essentio Desktop PC CM1745. http://www.ascendtech.us/asus-f2a85-m-cm1745-dp-motherboard_i_mb90mibiw5g0xb...
Looks like RS232 level translator ICs are also missing and some other differences on BOM too.
Indeed, there seem to be different versions of the board then. I have the retail version, and mine has the connectors soldered. Can someone update the wiki, please?
Cheers, Daniel
I tried different ways to initialize the VGA card - does not work. I also tried with your config file - did not work (as I remember, it was further suggested in the manual mode to complete the configuration). Here is my config file: http://pastebin.com/RVLcGku8 I have a feeling that coreboot is programmed or read (from the spi flash) to the wrong address, although it is unlikely because it is, as I understand it, is written in the mainboard sources, and I never touched them.
-------- Original Message -------- Subject: Re: [coreboot] Coreboot binary for ASUS F2A85-M Local Time: 23 Января 2017 г. 10:01 вечера UTC Time: 23 Января 2017 г. 19:01 From: daniel.ina1@googlemail.com To: Maxim Gusev mail@maximgusev.com Kyösti Mälkki kyosti.malkki@gmail.com, coreboot@coreboot.org coreboot@coreboot.org
On Mon, 23 Jan 2017 15:51:16 +0200 Kyösti Mälkki kyosti.malkki@gmail.com wrote:
On Mon, Jan 23, 2017 at 2:41 PM, Maxim Gusev via coreboot < coreboot@coreboot.org> wrote:
Hi Daniel,
Now I have compiled coreboot 4.5 with the SeaBIOS 1.9.3 as a payload and the VGAbios: I am using the Asus EN8600GT as a videocard (PCIe) and I took out the binary here: https://www.techpowerup.com/vgabios/?architecture=& manufacturer=Asus&model=8600+GT&interface=PCI-E&memType=& memSize=256&since=
To my understanding, when using an external graphics card you don't need to extract or put any VGA blobs in. But you need to initialize the PCIe video. Can you provide us with the full config you are using, please? Or did you try my config which I linked in my initial answer? (There, it should be already enabled as far as I remember)
Also I have turned on in console settings "Show POST codes...", but there is nothing works:(
You probably also need POST_DEVICE_PCI_PCIE set in your .config. In menuconfig: "Device to send POST codes to" -> "PCI/PCIe".
As for the serial port: I think this mainboard is not a retail version, but came from ASUS Essentio Desktop PC CM1745. http://www.ascendtech.us/asus-f2a85-m-cm1745-dp-motherboard_i_mb90mibiw5g0xb...
Looks like RS232 level translator ICs are also missing and some other differences on BOM too.
Indeed, there seem to be different versions of the board then. I have the retail version, and mine has the connectors soldered. Can someone update the wiki, please?
Cheers, Daniel
-
Daniel Kulesz -
Maxim Gusev