[commit] r5488 - in trunk/src: devices/oprom mainboard/artecgroup/dbe61/realmode northbridge/via/cn400 northbridge/via/cn700 northbridge/via/cx700 northbridge/via/vx800
Author: stepan Date: Sun Apr 25 01:15:23 2010 New Revision: 5488 URL: https://tracker.coreboot.org/trac/coreboot/changeset/5488
Log: drop all duplicate copies of vgabios.c in favor of devices/oprom/x86.c.
We have some tests on hardware. Moving RAMBASE to 1MB needs to wait a bit until C7 cache_as_ram.inc has been adapted to cache that area or things will become incredibly slow (1.5s boot time instead of 0.5)
Signed-off-by: Stefan Reinauer stepan@coresystems.de Acked-by: Stefan Reinauer stepan@coresystems.de
Deleted: trunk/src/mainboard/artecgroup/dbe61/realmode/ trunk/src/northbridge/via/cn400/vgabios.c trunk/src/northbridge/via/cn400/vgachip.h trunk/src/northbridge/via/cn700/vgabios.c trunk/src/northbridge/via/cn700/vgachip.h trunk/src/northbridge/via/cx700/vgabios.c trunk/src/northbridge/via/vx800/vgabios.c trunk/src/northbridge/via/vx800/vgachip.h Modified: trunk/src/devices/oprom/x86.c trunk/src/northbridge/via/cn400/Kconfig trunk/src/northbridge/via/cn400/Makefile.inc trunk/src/northbridge/via/cn400/vga.c trunk/src/northbridge/via/cn700/Kconfig trunk/src/northbridge/via/cn700/Makefile.inc trunk/src/northbridge/via/cn700/vga.c trunk/src/northbridge/via/cx700/Kconfig trunk/src/northbridge/via/cx700/Makefile.inc trunk/src/northbridge/via/cx700/cx700_vga.c trunk/src/northbridge/via/vx800/Kconfig trunk/src/northbridge/via/vx800/Makefile.inc trunk/src/northbridge/via/vx800/vga.c
Modified: trunk/src/devices/oprom/x86.c ============================================================================== --- trunk/src/devices/oprom/x86.c Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/devices/oprom/x86.c Sun Apr 25 01:15:23 2010 (r5488) @@ -134,11 +134,13 @@
/* Many option ROMs use the hard coded interrupt entry points in the * system bios. So install them at the known locations. - * Only need int10 so far. */ /* int42 is the relocated int10 */ - write_idt_stub((void *)0xff065, 0x42); + write_idt_stub((void *)0xff065, 0x42); + + /* VIA's VBIOS calls f000:f859 instead of int15 */ + write_idt_stub((void *)0xff859, 0x15); }
void run_bios(struct device *dev, unsigned long addr)
Modified: trunk/src/northbridge/via/cn400/Kconfig ============================================================================== --- trunk/src/northbridge/via/cn400/Kconfig Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn400/Kconfig Sun Apr 25 01:15:23 2010 (r5488) @@ -6,17 +6,6 @@ default 0 depends on NORTHBRIDGE_VIA_CN400
-# this is done by the northbridge's vgabios.c already -config VGA_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_CN400 - -config PCI_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_CN400 - # TODO: Values are from the CX700 datasheet, not sure if this matches CN400. # TODO: What should be the per-chipset default value here? choice
Modified: trunk/src/northbridge/via/cn400/Makefile.inc ============================================================================== --- trunk/src/northbridge/via/cn400/Makefile.inc Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn400/Makefile.inc Sun Apr 25 01:15:23 2010 (r5488) @@ -18,8 +18,6 @@ ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ##
-obj-y += vgabios.o - driver-y += northbridge.o driver-y += agp.o driver-y += vga.o
Modified: trunk/src/northbridge/via/cn400/vga.c ============================================================================== --- trunk/src/northbridge/via/cn400/vga.c Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn400/vga.c Sun Apr 25 01:15:23 2010 (r5488) @@ -33,24 +33,63 @@ #include <string.h> #include <bitops.h> #include <cpu/cpu.h> +#include <arch/interrupt.h> #include "chip.h" #include "northbridge.h" #include "cn400.h" -#include "vgachip.h"
-void write_protect_vgabios(void) +static int via_cn400_int15_handler(struct eregs *regs) { - /* Don't bother for now. */ + int res=-1; + printk(BIOS_DEBUG, "via_cn400_int15_handler\n"); + switch(regs->eax & 0xffff) { + case 0x5f19: + break; + case 0x5f18: + regs->eax=0x5f; + regs->ebx=0x545; // MCLK = 133, 32M frame buffer, 256 M main memory + regs->ecx=0x060; + res=0; + break; + case 0x5f00: + regs->eax = 0x8600; + break; + case 0x5f01: + regs->eax = 0x5f; + regs->ecx = (regs->ecx & 0xffffff00 ) | 2; // panel type = 2 = 1024 * 768 + res = 0; + break; + case 0x5f02: + regs->eax=0x5f; + regs->ebx= (regs->ebx & 0xffff0000) | 2; + regs->ecx= (regs->ecx & 0xffff0000) | 0x401; // PAL + crt only + regs->edx= (regs->edx & 0xffff0000) | 0; // TV Layout - default + res=0; + break; + case 0x5f0f: + regs->eax=0x860f; + break; + default: + printk(BIOS_DEBUG, "Unknown INT15 function %04x!\n", + regs->eax & 0xffff); + break; + } + return res; }
static void vga_init(device_t dev) { u8 reg8; u32 temp; -#ifdef DEBUG_CN400 - int i, j; -#endif
+ mainboard_interrupt_handlers(0x15, &via_cn400_int15_handler); + +#undef OLD_BOCHS_METHOD +#ifdef OLD_BOCHS_METHOD + // XXX We might need more bios hooks in the f segment, but + // this way of copying the BOCHS BIOS does not work anymore. + // As soon as someone verifies that CN400 can init VGA, the + // code should be removed. temp = (0xffffffff - CONFIG_FALLBACK_SIZE - 0xffff); printk(BIOS_DEBUG, "Copying BOCHS BIOS from 0x%08X to 0xf000\n", temp); /* @@ -59,7 +98,7 @@ */ //memcpy(0xf0000, (0xffffffff - CONFIG_ROM_SIZE - 0xffff), 0x10000); memcpy((void *)0xf0000, (void *)temp, 0x10000); - printk(BIOS_DEBUG, "Initializing VGA\n"); +#endif
/* Set memory rate to 200 MHz. */ outb(0x3d, CRTM_INDEX); @@ -79,16 +118,13 @@ pci_write_config32(dev, 0x10, 0xf0000008); pci_write_config32(dev, 0x14, 0xf4000000);
- printk(BIOS_DEBUG, "INSTALL REAL-MODE IDT\n"); - setup_realmode_idt(); - printk(BIOS_DEBUG, "DO THE VGA BIOS\n"); - do_vgabios(); - /* VGA seems to work without this, but crash & burn with it. */ - // printk(BIOS_DEBUG, "Enable VGA console\n"); - // vga_enable_console(); + printk(BIOS_DEBUG, "Initializing VGA...\n"); + + pci_dev_init(dev);
/* It's not clear if these need to be programmed before or after * the VGA BIOS runs. Try both, clean up later. */ + /* Set memory rate to 200 MHz (again). */ outb(0x3d, CRTM_INDEX); reg8 = inb(CRTM_DATA); @@ -102,10 +138,14 @@ outb(0x39, SR_INDEX); outb(reg8, SR_DATA);
+#ifdef OLD_BOCHS_METHOD /* Clear the BOCHS BIOS out of memory, so it doesn't confuse Linux. */ memset((void *)0xf0000, 0, 0x10000); +#endif
#ifdef DEBUG_CN400 + int i, j; + printk(BIOS_SPEW, "%s PCI Header Regs::\n", dev_path(dev));
for (i = 0 ; i < 16; i++)
Modified: trunk/src/northbridge/via/cn700/Kconfig ============================================================================== --- trunk/src/northbridge/via/cn700/Kconfig Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn700/Kconfig Sun Apr 25 01:15:23 2010 (r5488) @@ -7,17 +7,6 @@ default 0 depends on NORTHBRIDGE_VIA_CN700
-# this is done by the northbridge's vgabios.c already -config VGA_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_CN700 - -config PCI_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_CN700 - # TODO: Values are from the CX700 datasheet, not sure if this matches CN700. # TODO: What should be the per-chipset default value here? choice
Modified: trunk/src/northbridge/via/cn700/Makefile.inc ============================================================================== --- trunk/src/northbridge/via/cn700/Makefile.inc Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn700/Makefile.inc Sun Apr 25 01:15:23 2010 (r5488) @@ -18,8 +18,6 @@ ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ##
-obj-y += vgabios.o - driver-y += northbridge.o driver-y += agp.o driver-y += vga.o
Modified: trunk/src/northbridge/via/cn700/vga.c ============================================================================== --- trunk/src/northbridge/via/cn700/vga.c Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cn700/vga.c Sun Apr 25 01:15:23 2010 (r5488) @@ -33,28 +33,65 @@ #include <string.h> #include <bitops.h> #include <cpu/cpu.h> +#include <arch/interrupt.h> #include "chip.h" #include "northbridge.h" #include "cn700.h" -#include "vgachip.h"
-void write_protect_vgabios(void) +static int via_cn700_int15_handler(struct eregs *regs) { - /* Don't bother for now. */ + int res=-1; + printk(BIOS_DEBUG, "via_cn700_int15_handler\n"); + switch(regs->eax & 0xffff) { + case 0x5f19: + break; + case 0x5f18: + regs->eax=0x5f; + regs->ebx=0x545; // MCLK = 133, 32M frame buffer, 256 M main memory + regs->ecx=0x060; + res=0; + break; + case 0x5f00: + regs->eax = 0x8600; + break; + case 0x5f01: + regs->eax = 0x5f; + regs->ecx = (regs->ecx & 0xffffff00 ) | 2; // panel type = 2 = 1024 * 768 + res = 0; + break; + case 0x5f02: + regs->eax=0x5f; + regs->ebx= (regs->ebx & 0xffff0000) | 2; + regs->ecx= (regs->ecx & 0xffff0000) | 0x401; // PAL + crt only + regs->edx= (regs->edx & 0xffff0000) | 0; // TV Layout - default + res=0; + break; + case 0x5f0f: + regs->eax=0x860f; + break; + default: + printk(BIOS_DEBUG, "Unknown INT15 function %04x!\n", + regs->eax & 0xffff); + break; + } + return res; }
static void vga_init(device_t dev) { u8 reg8;
+ mainboard_interrupt_handlers(0x15, &via_cn700_int15_handler); + +#undef OLD_BOCHS_METHOD +#ifdef OLD_BOCHS_METHOD print_debug("Copying BOCHS BIOS to 0xf000\n"); /* * Copy BOCHS BIOS from 4G-CONFIG_ROM_SIZE-64k (in flash) to 0xf0000 (in RAM) * This is for compatibility with the VGA ROM's BIOS callbacks. */ memcpy((void *)0xf0000, (const void *)(0xffffffff - CONFIG_ROM_SIZE - 0xffff), 0x10000); - - printk(BIOS_DEBUG, "Initializing VGA\n"); +#endif
/* Set memory rate to 200 MHz. */ outb(0x3d, CRTM_INDEX); @@ -74,13 +111,9 @@ pci_write_config32(dev, 0x10, 0xf4000008); pci_write_config32(dev, 0x14, 0xfb000000);
- printk(BIOS_DEBUG, "INSTALL REAL-MODE IDT\n"); - setup_realmode_idt(); - printk(BIOS_DEBUG, "DO THE VGA BIOS\n"); - do_vgabios(); - /* VGA seems to work without this, but crash & burn with it. */ - // printk(BIOS_DEBUG, "Enable VGA console\n"); - // vga_enable_console(); + printk(BIOS_DEBUG, "Initializing VGA...\n"); + + pci_dev_init(dev);
/* It's not clear if these need to be programmed before or after * the VGA BIOS runs. Try both, clean up later. */ @@ -97,8 +130,10 @@ outb(0x39, SR_INDEX); outb(reg8, SR_DATA);
+#ifdef OLD_BOCHS_METHOD /* Clear the BOCHS BIOS out of memory, so it doesn't confuse Linux. */ memset((void *)0xf0000, 0, 0x10000); +#endif }
static const struct device_operations vga_operations = {
Modified: trunk/src/northbridge/via/cx700/Kconfig ============================================================================== --- trunk/src/northbridge/via/cx700/Kconfig Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cx700/Kconfig Sun Apr 25 01:15:23 2010 (r5488) @@ -5,14 +5,35 @@ select IOAPIC select SMP
-# this is done by the northbridge's vgabios.c already -config VGA_ROM_RUN - bool - default n +# TODO: What should be the per-chipset default value here? +choice + prompt "Onboard graphics" + default CX700_VIDEO_MB_32MB depends on NORTHBRIDGE_VIA_CX700
-config PCI_ROM_RUN - bool - default n +# TODO: Setting the amount of gfx memory is not yet supported in the source code. +config CX700_VIDEO_MB_OFF + bool "Disabled, 0KB" +config CX700_VIDEO_MB_8MB + bool "Enabled, 8MB" +config CX700_VIDEO_MB_16MB + bool "Enabled, 16MB" +config CX700_VIDEO_MB_32MB + bool "Enabled, 32MB" +config CX700_VIDEO_MB_64MB + bool "Enabled, 64MB" +config CX700_VIDEO_MB_128MB + bool "Enabled, 128MB" + +endchoice + +config VIDEO_MB + int + default 0 if CX700_VIDEO_MB_OFF + default 8 if CX700_VIDEO_MB_8MB + default 16 if CX700_VIDEO_MB_16MB + default 32 if CX700_VIDEO_MB_32MB + default 64 if CX700_VIDEO_MB_64MB + default 128 if CX700_VIDEO_MB_128MB depends on NORTHBRIDGE_VIA_CX700
Modified: trunk/src/northbridge/via/cx700/Makefile.inc ============================================================================== --- trunk/src/northbridge/via/cx700/Makefile.inc Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cx700/Makefile.inc Sun Apr 25 01:15:23 2010 (r5488) @@ -19,7 +19,6 @@
obj-y += cx700_reset.o obj-y += northbridge.o -obj-y += vgabios.o
driver-y += cx700_agp.o driver-y += cx700_lpc.o
Modified: trunk/src/northbridge/via/cx700/cx700_vga.c ============================================================================== --- trunk/src/northbridge/via/cx700/cx700_vga.c Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/cx700/cx700_vga.c Sun Apr 25 01:15:23 2010 (r5488) @@ -29,6 +29,7 @@ #include <cpu/cpu.h> #include <cpu/x86/mtrr.h> #include <cpu/x86/msr.h> +#include <arch/interrupt.h> #include "chip.h" #include "northbridge.h"
@@ -41,9 +42,44 @@ #define CRTC_INDEX 0x3d4 #define CRTC_DATA 0x3d5
-void setup_realmode_idt(void); -void do_vgabios(void); -void vga_enable_console(void); +static int via_cx700_int15_handler(struct eregs *regs) +{ + int res=-1; + printk(BIOS_DEBUG, "via_cx700_int15_handler\n"); + switch(regs->eax & 0xffff) { + case 0x5f19: + break; + case 0x5f18: + regs->eax=0x5f; + regs->ebx=0x545; // MCLK = 133, 32M frame buffer, 256 M main memory + regs->ecx=0x060; + res=0; + break; + case 0x5f00: + regs->eax = 0x8600; + break; + case 0x5f01: + regs->eax = 0x5f; + regs->ecx = (regs->ecx & 0xffffff00 ) | 2; // panel type = 2 = 1024 * 768 + res = 0; + break; + case 0x5f02: + regs->eax=0x5f; + regs->ebx= (regs->ebx & 0xffff0000) | 2; + regs->ecx= (regs->ecx & 0xffff0000) | 0x401; // PAL + crt only + regs->edx= (regs->edx & 0xffff0000) | 0; // TV Layout - default + res=0; + break; + case 0x5f0f: + regs->eax=0x860f; + break; + default: + printk(BIOS_DEBUG, "Unknown INT15 function %04x!\n", + regs->eax & 0xffff); + break; + } + return res; +}
void write_protect_vgabios(void) { @@ -64,7 +100,7 @@ { u8 reg8;
- printk(BIOS_DEBUG, "Initializing VGA...\n"); + mainboard_interrupt_handlers(0x15, &via_cx700_int15_handler);
//* pci_write_config8(dev, 0x04, 0x07); @@ -75,12 +111,16 @@ pci_write_config8(dev, 0x3c, 0x0b); //*/
- printk(BIOS_DEBUG, "Executing VGA option rom in real mode\n"); - setup_realmode_idt(); - do_vgabios(); + printk(BIOS_DEBUG, "Initializing VGA...\n"); + + pci_dev_init(dev); + printk(BIOS_DEBUG, "Enable VGA console\n"); + // this is how it should look: + // call_bios_interrupt(0x10,0x4f1f,0x8003,1,0); + // this is how it looks: vga_enable_console(); - + /* It's not clear if these need to be programmed before or after * the VGA bios runs. Try both, clean up later */ /* Set memory rate to 200MHz */
Modified: trunk/src/northbridge/via/vx800/Kconfig ============================================================================== --- trunk/src/northbridge/via/vx800/Kconfig Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/vx800/Kconfig Sun Apr 25 01:15:23 2010 (r5488) @@ -6,14 +6,3 @@ default 0 depends on NORTHBRIDGE_VIA_VX800
-# this is done by the northbridge's vgabios.c already -config VGA_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_VX800 - -config PCI_ROM_RUN - bool - default n - depends on NORTHBRIDGE_VIA_VX800 -
Modified: trunk/src/northbridge/via/vx800/Makefile.inc ============================================================================== --- trunk/src/northbridge/via/vx800/Makefile.inc Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/vx800/Makefile.inc Sun Apr 25 01:15:23 2010 (r5488) @@ -18,8 +18,6 @@ ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ##
-obj-y += vgabios.o - driver-y += northbridge.o driver-y += vga.o driver-y += vx800_lpc.o
Modified: trunk/src/northbridge/via/vx800/vga.c ============================================================================== --- trunk/src/northbridge/via/vx800/vga.c Sat Apr 24 23:24:06 2010 (r5487) +++ trunk/src/northbridge/via/vx800/vga.c Sun Apr 25 01:15:23 2010 (r5488) @@ -32,9 +32,9 @@ #include <cpu/cpu.h> #include <cpu/x86/mtrr.h> #include <cpu/x86/msr.h> +#include <arch/interrupt.h> #include "chip.h" #include "northbridge.h" -#include "vgachip.h"
/* PCI Domain 1 Device 0 Function 0 */
@@ -49,6 +49,83 @@ #define VIACONFIG_VGA_PCI_10 0xf8000008 #define VIACONFIG_VGA_PCI_14 0xfc000000
+static int via_vx800_int15_handler(struct eregs *regs) +{ + int res=-1; + printk(BIOS_DEBUG, "via_vx800_int15_handler\n"); + switch(regs->eax & 0xffff) { + case 0x5f19: + regs->eax=0x5f; + regs->ecx=0x03; + res=0; + break; + case 0x5f18: + { + /* + * BL Bit[7:4] + * Memory Data Rate + * 0000: 66MHz + * 0001: 100MHz + * 0010: 133MHz + * 0011: 200MHz ( DDR200 ) + * 0100: 266MHz ( DDR266 ) + * 0101: 333MHz ( DDR333 ) + * 0110: 400MHz ( DDR400 ) + * 0111: 533MHz ( DDR I/II 533 + * 1000: 667MHz ( DDR I/II 667) + * Bit[3:0] + * N: Frame Buffer Size 2^N MB + */ + u8 i; + device_t dev; + dev = dev_find_slot(0, PCI_DEVFN(0, 3)); + i = pci_read_config8(dev, 0xa1); + i = (i & 0x70); + i = i >> 4; + if (i == 0) { + regs->eax = 0x00; //not support 5f18 + break; + } + i = i + 2; + regs->ebx = (u32) i; + i = pci_read_config8(dev, 0x90); + i = (i & 0x07); + i = i + 3; + i = i << 4; + regs->ebx = regs->ebx + ((u32) i); + regs->eax = 0x5f; + res = 0; + break; + } + case 0x5f00: + regs->eax = 0x005f; + res = 0; + break; + case 0x5f01: + regs->eax = 0x5f; + regs->ecx = (regs->ecx & 0xffffff00 ) | 2; // panel type = 2 = 1024 * 768 + res = 0; + break; + case 0x5f02: + regs->eax=0x5f; + regs->ebx= (regs->ebx & 0xffff0000) | 2; + regs->ecx= (regs->ecx & 0xffff0000) | 0x401; // PAL + crt only + regs->edx= (regs->edx & 0xffff0000) | 0; // TV Layout - default + res=0; + break; + case 0x5f0f: + regs->eax = 0x005f; + res = 0; + break; + default: + printk(BIOS_DEBUG, "Unknown INT15 function %04x!\n", + regs->eax & 0xffff); + regs->eax = 0; + break; + } + return res; +} + void write_protect_vgabios(void) { device_t dev; @@ -70,12 +147,12 @@ { uint8_t reg8;
- print_debug("Initiailizing VGA...\n"); - u8 tmp8; -//A20 OPEN - tmp8 = inb(0x92); - tmp8 = tmp8 | 2; - outb(tmp8, 0x92); + mainboard_interrupt_handlers(0x15, &via_vx800_int15_handler); + + //A20 OPEN + reg8 = inb(0x92); + reg8 = reg8 | 2; + outb(reg8, 0x92);
//* //pci_write_config8(dev, 0x04, 0x07); @@ -85,27 +162,17 @@ pci_write_config32(dev, 0x14, VIACONFIG_VGA_PCI_14); pci_write_config8(dev, 0x3c, 0x0a); //same with vx855_lpc.c //*/ - printk(BIOS_EMERG, "file '%s', line %d\n\n", __FILE__, __LINE__);
-#if 1 - printk(BIOS_DEBUG, "INSTALL REAL-MODE IDT\n"); - setup_realmode_idt(); - printk(BIOS_DEBUG, "DO THE VGA BIOS\n"); + printk(BIOS_DEBUG, "Initializing VGA...\n"); + + pci_dev_init(dev); + + printk(BIOS_DEBUG, "Enable VGA console\n"); + // this is how it should look: + // call_bios_interrupt(0x10,0x4f1f,0x8003,1,0); + // this is how it looks: + vga_enable_console();
- do_vgabios(); - if ((acpi_sleep_type == 3)/* || (PAYLOAD_IS_SEABIOS == 0)*/) { - printk(BIOS_DEBUG, "Enable VGA console\n"); - // remove this function since in cn700 it is said "VGA seems to work without this, but crash & burn with it" - //but the existense of vga_enable_console() seems do not hurt my coreboot. XP+ubuntu s3 can resume with and without this function. - //and remove it also do not help my s3 problem: desktop screen have some thin black line, after resuming back to win. - vga_enable_console(); - } -#else -/* Attempt to manually force the rom to load */ - printk(BIOS_DEBUG, "Forcing rom load\n"); - pci_rom_load(dev, 0xfff80000); - run_bios(dev, 0xc0000); -#endif if ((acpi_sleep_type == 3)/* || (PAYLOAD_IS_SEABIOS == 0)*/) { /* It's not clear if these need to be programmed before or after * the VGA bios runs. Try both, clean up later */ @@ -117,13 +184,13 @@ outb(0x3d, CRTM_INDEX); outb(reg8, CRTM_DATA);
+#if 0 /* Set framebuffer size to CONFIG_VIDEO_MB mb */ - /*reg8 = (CONFIG_VIDEO_MB/4); - outb(0x39, SR_INDEX); - outb(reg8, SR_DATA); */ + reg8 = (CONFIG_VIDEO_MB/4); + outb(0x39, SR_INDEX); + outb(reg8, SR_DATA); +#endif } - printk(BIOS_EMERG, "file '%s', line %d\n\n", __FILE__, __LINE__); - }
static struct device_operations vga_operations = {
-
repository service