Hi there,
I've got a Tyan s2882 system with 2 single core CPUs, both AMD Opteron(tm) Processor 242. Under the proprietary BIOS, both CPUs show up in /proc/cpuinfo.
Under coreboot (latest revision, r3114), I only get 1 CPU. I've attached the output (debug_level=Spew) below. You'll see it finds both CPUs initially
... CPU: APIC: 00 enabled ... CPU: APIC: 01 enabled ...
but then fails to initialize CPU#1:
... CPU #0 Initialized CPU 0x01 would not start! CPU 0x01 did not initialize! All AP CPUs stopped ...
Any thoughts on what is wrong here, or what I can do to provide more debug information?
Thanks, Ward.
==========================================================================
INIT detected from ---- {APICID = 00 NODEID = 00 COREID = 00} ---
Issuing SOFT_RESET...
coreboot-2.0.0_s2882_Fallback Thu Feb 21 16:43:43 EST 2008 starting... (0,1) link=01 (1,0) link=01 02 nodes initialized. SBLink=00 NC node|link=00 Ram1.00 Ram1.01 Ram2.00 Ram2.01 Ram3 Initializing memory: done Initializing memory: done Ram4 v_esp=000cffc8 testx = 5a5a5a5a Copying data from cache to RAM -- switching to use RAM as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying coreboot to RAM. src=fffe0000 dst=00004000 linxbios_ram.nrv2b length = 0000d536 linxbios_ram.bin length = 0002726c Jumping to coreboot. coreboot-2.0.0_s2882_Fallback Thu Feb 21 16:43:43 EST 2008 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled PCI: 00:18.3 siblings=0 CPU: APIC: 00 enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled PCI: 00:19.3 siblings=0 CPU: APIC: 01 enabled PCI: pci_scan_bus for bus 00 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled PCI: 01:00.0 [1022/7450] enabled PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003 PCI: 01:00.0 [1022/7460] enabled PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007 PCI: pci_scan_bus for bus 01 PCI: 01:01.0 [1022/7450] enabled PCI: 01:01.1 [1022/7451] enabled PCI: 01:02.0 [1022/7450] enabled PCI: 01:02.1 [1022/7451] enabled PCI: 01:03.0 [1022/7460] enabled PCI: 01:04.0 [1022/7468] enabled PCI: 01:04.1 [1022/7469] enabled PCI: 01:04.2 [1022/746a] enabled PCI: 01:04.3 [1022/746b] enabled PCI: pci_scan_bus for bus 02 Disabling static device: PCI: 02:06.0 Disabling static device: PCI: 02:06.1 PCI: 02:09.0 [14e4/1648] enabled PCI: 02:09.1 [14e4/1648] enabled PCI: pci_scan_bus returning with max=002 PCI: 02: 100MHz PCI-X PCI: pci_scan_bus for bus 03 PCI: 03:03.0 [1095/3124] enabled PCI: pci_scan_bus returning with max=003 PCI: 03: Conventional PCI PCI: pci_scan_bus for bus 04 PCI: 04:00.0 [1022/7464] enabled PCI: 04:00.1 [1022/7464] enabled PCI: 04:05.0 [1095/3114] enabled PCI: 04:06.0 [1002/4752] enabled PCI: 04:08.0 [8086/1229] enabled PCI: pci_scan_bus returning with max=004 PNP: 002e.0 enabled PNP: 002e.1 disabled PNP: 002e.2 enabled PNP: 002e.3 disabled PNP: 002e.5 enabled PNP: 002e.6 disabled PNP: 002e.7 disabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled PNP: 002e.b enabled PCI: pci_scan_bus returning with max=004 PCI: pci_scan_bus returning with max=004 done Allocating resources... Reading resources... PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 02 io PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 02 prefmem PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 03 prefmem PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 04 prefmem Done reading resources. Allocating VGA resource PCI: 04:06.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 01:03.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Setting resources... VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device PCI: 00:18.0 1b8 <- [0x00fd400000 - 0x00fd3fffff] size 0x00000000 gran 0x14 prefmem <node 0 link 0> PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] size 0x00003000 gran 0x0c io <node 0 link 0> PCI: 00:18.0 1b0 <- [0x00fc000000 - 0x00fd3fffff] size 0x01400000 gran 0x14 mem <node 0 link 0> PCI: 01:01.0 20 <- [0x00fd100000 - 0x00fd1fffff] size 0x00100000 gran 0x14 bus 02 mem PCI: 02:09.0 10 <- [0x00fd100000 - 0x00fd10ffff] size 0x00010000 gran 0x10 mem64 PCI: 02:09.0 18 <- [0x00fd110000 - 0x00fd11ffff] size 0x00010000 gran 0x10 mem64 PCI: 02:09.1 10 <- [0x00fd120000 - 0x00fd12ffff] size 0x00010000 gran 0x10 mem64 PCI: 02:09.1 18 <- [0x00fd130000 - 0x00fd13ffff] size 0x00010000 gran 0x10 mem64 PCI: 01:01.1 10 <- [0x00fd300000 - 0x00fd300fff] size 0x00001000 gran 0x0c mem64 PCI: 01:02.0 1c <- [0x0000001000 - 0x0000001fff] size 0x00001000 gran 0x0c bus 03 io PCI: 01:02.0 20 <- [0x00fd200000 - 0x00fd2fffff] size 0x00100000 gran 0x14 bus 03 mem PCI: 03:03.0 10 <- [0x00fd288000 - 0x00fd28807f] size 0x00000080 gran 0x07 mem64 PCI: 03:03.0 18 <- [0x00fd280000 - 0x00fd287fff] size 0x00008000 gran 0x0f mem64 PCI: 03:03.0 20 <- [0x0000001000 - 0x000000100f] size 0x00000010 gran 0x04 io PCI: 03:03.0 30 <- [0x00fd200000 - 0x00fd27ffff] size 0x00080000 gran 0x13 romem PCI: 01:02.1 10 <- [0x00fd301000 - 0x00fd301fff] size 0x00001000 gran 0x0c mem64 PCI: 01:03.0 1c <- [0x0000002000 - 0x0000002fff] size 0x00001000 gran 0x0c bus 04 io PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] size 0x01100000 gran 0x14 bus 04 mem PCI: 04:00.0 10 <- [0x00fd020000 - 0x00fd020fff] size 0x00001000 gran 0x0c mem PCI: 04:00.1 10 <- [0x00fd021000 - 0x00fd021fff] size 0x00001000 gran 0x0c mem PCI: 04:05.0 10 <- [0x0000002450 - 0x0000002457] size 0x00000008 gran 0x03 io PCI: 04:05.0 14 <- [0x0000002470 - 0x0000002473] size 0x00000004 gran 0x02 io PCI: 04:05.0 18 <- [0x0000002460 - 0x0000002467] size 0x00000008 gran 0x03 io PCI: 04:05.0 1c <- [0x0000002480 - 0x0000002483] size 0x00000004 gran 0x02 io PCI: 04:05.0 20 <- [0x0000002440 - 0x000000244f] size 0x00000010 gran 0x04 io PCI: 04:05.0 24 <- [0x00fd024000 - 0x00fd0243ff] size 0x00000400 gran 0x0a mem PCI: 04:06.0 10 <- [0x00fc000000 - 0x00fcffffff] size 0x01000000 gran 0x18 mem PCI: 04:06.0 14 <- [0x0000002000 - 0x00000020ff] size 0x00000100 gran 0x08 io PCI: 04:06.0 18 <- [0x00fd022000 - 0x00fd022fff] size 0x00001000 gran 0x0c mem PCI: 04:06.0 30 <- [0x00fff00000 - 0x00fff1ffff] size 0x00020000 gran 0x11 romem PCI: 04:08.0 10 <- [0x00fd023000 - 0x00fd023fff] size 0x00001000 gran 0x0c mem PCI: 04:08.0 14 <- [0x0000002400 - 0x000000243f] size 0x00000040 gran 0x06 io PCI: 04:08.0 18 <- [0x00fd000000 - 0x00fd01ffff] size 0x00020000 gran 0x11 mem PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] size 0x00000008 gran 0x03 io PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] size 0x00000001 gran 0x00 irq PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] size 0x00000001 gran 0x00 drq PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] size 0x00000008 gran 0x03 io PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] size 0x00000001 gran 0x00 irq PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] size 0x00000001 gran 0x00 io PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] size 0x00000001 gran 0x00 io PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] size 0x00000001 gran 0x00 irq PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] size 0x00000001 gran 0x00 irq PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] size 0x00000008 gran 0x03 io PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] size 0x00000001 gran 0x00 irq PCI: 01:04.1 20 <- [0x0000003420 - 0x000000342f] size 0x00000010 gran 0x04 io PCI: 01:04.2 10 <- [0x0000003400 - 0x000000341f] size 0x00000020 gran 0x05 io PCI: 01:04.3 58 <- [0x0000003000 - 0x00000030ff] size 0x00000100 gran 0x08 io PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] size 0x04000000 gran 0x1a mem <gart> PCI: 00:19.3 94 <- [0x00f8000000 - 0x00fbffffff] size 0x04000000 gran 0x1a mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 00 PCI: 01:01.0 bridge ctrl <- 0003 PCI: 01:01.0 cmd <- 06 PCI: 02:09.0 subsystem <- 10f1/2882 PCI: 02:09.0 cmd <- 02 PCI: 02:09.1 subsystem <- 10f1/2882 PCI: 02:09.1 cmd <- 02 PCI: 01:01.1 subsystem <- 10f1/2882 PCI: 01:01.1 cmd <- 06 PCI: 01:02.0 bridge ctrl <- 0003 PCI: 01:02.0 cmd <- 07 PCI: 03:03.0 cmd <- 83 PCI: 01:02.1 subsystem <- 10f1/2882 PCI: 01:02.1 cmd <- 06 PCI: 01:03.0 bridge ctrl <- 000b PCI: 01:03.0 cmd <- 07 PCI: 04:00.0 subsystem <- 10f1/2882 PCI: 04:00.0 cmd <- 02 PCI: 04:00.1 subsystem <- 10f1/2882 PCI: 04:00.1 cmd <- 02 PCI: 04:05.0 subsystem <- 10f1/2882 PCI: 04:05.0 cmd <- 03 PCI: 04:06.0 subsystem <- 10f1/2882 PCI: 04:06.0 cmd <- 83 PCI: 04:08.0 subsystem <- 10f1/2882 PCI: 04:08.0 cmd <- 03 PCI: 01:04.0 subsystem <- 10f1/2882 PCI: 01:04.0 cmd <- 0f w83627hf hwm smbus enabled PCI: 01:04.1 subsystem <- 10f1/2882 PCI: 01:04.1 cmd <- 01 PCI: 01:04.2 subsystem <- 10f1/2882 PCI: 01:04.2 cmd <- 01 PCI: 01:04.3 subsystem <- 10f1/2882 PCI: 01:04.3 cmd <- 01 PCI: 00:18.1 subsystem <- 10f1/2882 PCI: 00:18.1 cmd <- 00 PCI: 00:18.2 subsystem <- 10f1/2882 PCI: 00:18.2 cmd <- 00 PCI: 00:18.3 cmd <- 00 PCI: 00:19.0 cmd <- 00 PCI: 00:19.1 cmd <- 00 PCI: 00:19.2 cmd <- 00 PCI: 00:19.3 cmd <- 00 done. Initializing devices... Root Device init APIC_CLUSTER: 0 init Initializing CPU #0 CPU: vendor AMD device f5a CPU: family 0f, model 05, stepping 0a Enabling cache
Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB DONE variable MTRRs Clear out the extra MTRR's
MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled
microcode: equivalent rev id = 0x004a, current patch id = 0x00000000 microcode: patch id to apply = 0x00000047 microcode: updated to patch id = 0x00000047 success
CPU model AMD Opteron(tm) Processor 242 Setting up local apic... apic_id: 0x00 done. Clearing memory 2048K - 1048576K: --------------- done CPU #0 Initialized CPU 0x01 would not start! CPU 0x01 did not initialize! All AP CPUs stopped PCI: 00:18.0 init PCI: 01:01.0 init PCI: 02:09.0 init PCI: 02:09.1 init PCI: 01:02.0 init PCI: 01:03.0 init PCI: 04:05.0 init PCI: 04:06.0 init rom address for PCI: 04:06.0 = fff00000 copying VGA ROM Image from 0xfff00000 to 0xc0000, 0x9000 bytes entering emulator halt_sys: file /home/ward/Desktop/buildrom3/buildrom-devel/work/coreboot/svn/src/devices/emulator/x86emu/ops.c, line 4387 PCI: 04:08.0 init PCI: 01:04.0 init amd8111: ioapic bsp_apicid = 00 RTC Init enabling HPET @0xfed00000 PNP: 002e.0 init PNP: 002e.2 init PNP: 002e.5 init Keyboard init... PNP: 002e.b init PCI: 01:04.1 init IDE1 IDE0 PCI: 01:04.3 init set power on after power fail PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. PCI: 00:19.0 init PCI: 00:19.1 init PCI: 00:19.2 init PCI: 00:19.3 init NB: Function 3 Misc Control.. done. PCI: 03:03.0 init rom address for PCI: 03:03.0 = fd200000 copying non-VGA ROM Image from 0xfd200000 to 0xd0000, 0xf000 bytes entering emulator halt_sys: file /home/ward/Desktop/buildrom3/buildrom-devel/work/coreboot/svn/src/devices/emulator/x86emu/ops.c, line 183 Devices initialized Writing IRQ routing tables to 0xf0000... setting Onboard AMD Southbridge Assigning IRQ 10 to 1:4.2 Readback = 10 setting Onboard AMD USB Assigning IRQ 10 to 4:0.0 Readback = 10 Assigning IRQ 10 to 4:0.1 Readback = 10 setting Onboard ATI Display Adapter Assigning IRQ 11 to 4:6.0 Readback = 11 setting Slot 1 Assigning IRQ 5 to 3:3.0 Readback = 5 setting Slot 2 setting Slot 3 setting Slot 4 setting Slot 5 setting Onboard SI Serial ATA Assigning IRQ 10 to 4:5.0 Readback = 10 setting Onboard Intel NIC Assigning IRQ 11 to 4:8.0 Readback = 11 setting Onboard Adaptec SCSI setting Onboard Broadcom NIC Assigning IRQ 5 to 2:9.0 Readback = 5 Assigning IRQ 9 to 2:9.1 Readback = 9 done. Wrote the mp table end at: 00000020 - 00000200 Moving GDT to 0x500...ok Adjust low_table_end from 0x00000530 to 0x00001000 Adjust rom_table_end from 0x000f0400 to 0x00100000 Wrote coreboot table at: 00000530 - 00000e70 checksum 590d
Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3
rom_stream: 0xfffc0000 - 0xfffdffff Found ELF candidate at offset 0 header_offset is 0 Try to load at offset 0x0 New segment addr 0x100000 size 0x3ad80 offset 0xc0 filesize 0x10dc8 (cleaned up) New segment addr 0x100000 size 0x3ad80 offset 0xc0 filesize 0x10dc8 New segment addr 0x13ad80 size 0x48 offset 0x10ea0 filesize 0x48 (cleaned up) New segment addr 0x13ad80 size 0x48 offset 0x10ea0 filesize 0x48 Dropping non PT_LOAD segment Dropping non PT_LOAD segment Loading Segment: addr: 0x0000000000100000 memsz: 0x000000000003ad80 filesz: 0x0000000000010dc8 Clearing Segment: addr: 0x0000000000110dc8 memsz: 0x0000000000029fb8 Loading Segment: addr: 0x000000000013ad80 memsz: 0x0000000000000048 filesz: 0x0000000000000048 Jumping to boot code at 0x10c638 FILO version 0.5 (root@m57sli-soic) Thu Feb 21 16:43:15 EST 2008 menu: hda1:/boot/grub/menu.lst hda: LBA48 250GB: WDC WD2500SD-01KCB0 Mounted ext2fs Press any key to continue. Press any key to continue. Press any key to continue. Press any key to continue. Press any key to continue. Press `ESC' to enter the menu... 2 Press `ESC' to enter the menu... 1 Press `ESC' to enter the menu... 0 Booting 'hda1:/vmlinuz-2.6.22-14-generic root=/dev/md1 ro console=tty0 console= ttyS0,115200n8 initrd=/initrd.img-2.6.22-14-generic' Found Linux version 2.6.22-14-generic (buildd@crested) #1 SMP Sun Oct 14 21:45:15 GMT 2007 bzImage. Loading kernel... ok Loading initrd... ok Jumping to entry point... [ 0.000000] Linux version 2.6.22-14-generic (buildd@crested) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 21:45:15 GMT 2007 (Ubuntu 2.6.22-14.46-generic) [ 0.000000] Command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000001000 - 00000000000a0000 (usable) [ 0.000000] BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable) [ 0.000000] BIOS-e820: 0000000000100000 - 0000000080000000 (usable) [ 0.000000] end_pfn_map = 524288 [ 0.000000] DMI not present or invalid. [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] Number of nodes 2 [ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000040000000 [ 0.000000] Node 1 MemBase 0000000040000000 Limit 0000000080000000 [ 0.000000] Using node hash shift of 30 [ 0.000000] Bootmem setup node 0 0000000000000000-0000000040000000 [ 0.000000] Bootmem setup node 1 0000000040000000-0000000080000000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 1 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[4] active PFN ranges [ 0.000000] 0: 1 -> 160 [ 0.000000] 0: 192 -> 240 [ 0.000000] 0: 256 -> 262144 [ 0.000000] 1: 262144 -> 524288 [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: TYAN MPTABLE: Product ID: S2882 MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] I/O APIC #2 at 0xFEC00000. [ 0.000000] I/O APIC #3 at 0xFD300000. [ 0.000000] I/O APIC #4 at 0xFD301000. [ 0.000000] Setting APIC routing to flat [ 0.000000] Processors: 1 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000c0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:80000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 34696 bytes of per cpu data [ 0.000000] Built 2 zonelists. Total pages: 515949 [ 0.000000] Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 105.625839] time.c: Detected 1593.117 MHz processor. [ 105.631934] Console: colour VGA+ 80x25 [ 105.882827] Checking aperture... [ 105.886357] CPU 0: aperture @ f8000000 size 64 MB [ 105.891369] CPU 1: aperture @ f8000000 size 64 MB [ 105.932201] Memory: 2055820k/2097152k available (2274k kernel code, 41136k reserved, 1181k data, 296k init) [ 105.942366] SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=2 [ 106.027367] Calibrating delay using timer specific routine.. 3195.60 BogoMIPS (lpj=6391209) [ 106.036372] Security Framework v1.0.0 initialized [ 106.041381] SELinux: Disabled at boot. [ 106.045723] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 106.055229] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 106.063549] Mount-cache hash table entries: 256 [ 106.068563] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 106.076004] CPU: L2 Cache: 1024K (64 bytes/line) [ 106.080922] CPU 0/0 -> Node 0 [ 106.084209] SMP alternatives: switching to UP code [ 106.089468] Freeing SMP alternatives: 24k freed [ 106.095104] Early unpacking initramfs... done [ 106.481369] ACPI: Core revision 20070126 [ 106.485623] ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126] [ 106.496733] ACPI: Unable to load the System Description Tables [ 106.544180] Using local APIC timer interrupts. [ 106.611597] result 12446226 [ 106.614653] Detected 12.446 MHz APIC timer. [ 106.622728] Brought up 1 CPUs [ 106.626491] NET: Registered protocol family 16 [ 106.633045] PCI: Using configuration type 1 [ 106.637973] ACPI: Interpreter disabled. [ 106.642082] Linux Plug and Play Support v0.97 (c) Adam Belay [ 106.648028] pnp: PnP ACPI: disabled [ 106.651847] PCI: Probing PCI hardware [ 106.660061] PCI: Firmware left 0000:04:08.0 e100 interrupts enabled, disabling [ 106.668741] PCI: Discovered primary peer bus 01 [IRQ] [ 106.674096] PCI: Using IRQ router default [1022/746b] at 0000:01:04.3 [ 106.680856] PCI->APIC IRQ transform: 0000:01:04.2[D] -> IRQ 19 [ 106.686973] PCI->APIC IRQ transform: 0000:02:09.0[A] -> IRQ 24 [ 106.693090] PCI->APIC IRQ transform: 0000:02:09.1[B] -> IRQ 25 [ 106.699207] PCI->APIC IRQ transform: 0000:03:03.0[A] -> IRQ 28 [ 106.705328] PCI->APIC IRQ transform: 0000:04:00.0[D] -> IRQ 19 [ 106.711449] PCI->APIC IRQ transform: 0000:04:00.1[D] -> IRQ 19 [ 106.717575] PCI->APIC IRQ transform: 0000:04:05.0[A] -> IRQ 19 [ 106.723692] PCI->APIC IRQ transform: 0000:04:06.0[A] -> IRQ 18 [ 106.729814] PCI->APIC IRQ transform: 0000:04:08.0[A] -> IRQ 18 [ 106.736142] NET: Registered protocol family 8 [ 106.740785] NET: Registered protocol family 20 [ 106.745949] PCI: Bridge: 0000:01:01.0 [ 106.749894] Time: tsc clocksource has been installed. [ 106.755228] IO window: disabled. [ 106.758947] MEM window: fd100000-fd1fffff [ 106.763419] PREFETCH window: 88000000-880fffff [ 106.768321] PCI: Bridge: 0000:01:02.0 [ 106.772253] IO window: 1000-1fff [ 106.775942] MEM window: fd200000-fd2fffff [ 106.780409] PREFETCH window: disabled. [ 106.784618] PCI: Bridge: 0000:01:03.0 [ 106.788558] IO window: 2000-2fff [ 106.792251] MEM window: fc000000-fd0fffff [ 106.796726] PREFETCH window: 88100000-881fffff [ 106.801786] NET: Registered protocol family 2 [ 106.842508] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 106.850791] TCP established hash table entries: 262144 (order: 10, 6291456 bytes) [ 106.864689] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 106.872585] TCP: Hash tables configured (established 262144 bind 65536) [ 106.879482] TCP reno registered [ 106.894537] checking if image is initramfs... it is [ 107.641824] Freeing initrd memory: 7802k freed [ 107.656080] audit: initializing netlink socket (disabled) [ 107.661775] audit(1203630647.656:1): initialized [ 107.668983] VFS: Disk quotas dquot_6.5.1 [ 107.673242] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 107.680088] io scheduler noop registered [ 107.684315] io scheduler anticipatory registered [ 107.689220] io scheduler deadline registered [ 107.693899] io scheduler cfq registered (default) [ 107.698913] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:01:01.0 subordinate bus. [ 107.707986] PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for 0000:01:02.0 subordinate bus. [ 107.747960] Real Time Clock Driver v1.12ac [ 107.752445] Linux agpgart interface v0.102 (c) Dave Jones [ 107.758151] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ΓΏ[ 107.766550] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 107.773985] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 107.782161] input: Macintosh mouse button emulation as /class/input/input0 [ 107.789463] PNP: No PS/2 controller found. Probing ports directly. [ 107.798906] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 107.804159] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 107.809658] mice: PS/2 mouse device common for all mice [ 107.815291] TCP cubic registered [ 107.818884] NET: Registered protocol family 1 [ 107.823729] /build/buildd/linux-source-2.6.22-2.6.22/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 107.833924] Freeing unused kernel memory: 296k freed Loading, please wait... [ 107.885242] input: AT Translated Set 2 keyboard as /class/input/input1 Begin: Loading essential drivers... ... [ 107.921951] AppArmor: AppArmor initialized<5>audit(1203630647.920:2): type=1505 info="AppArmor initialized" pid=877 [ 107.939743] fuse init (API version 7.8) [ 107.948934] Failure registering capabilities with primary security module. [ 107.993501] thermal: Unknown symbol acpi_processor_set_thermal_limit [ 108.013449] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 108.037995] md: linear personality registered for level -1 [ 108.048532] md: multipath personality registered for level -4 [ 108.058987] md: raid0 personality registered for level 0 [ 108.069491] md: raid1 personality registered for level 1 [ 108.079320] raid5: automatically using best checksumming function: generic_sse [ 108.104899] generic_sse: 5125.000 MB/sec [ 108.109827] raid5: using function: generic_sse (5125.000 MB/sec) [ 108.184826] raid6: int64x1 1313 MB/s [ 108.256723] raid6: int64x2 1971 MB/s [ 108.328643] raid6: int64x4 1977 MB/s [ 108.400583] raid6: int64x8 1327 MB/s [ 108.472495] raid6: sse2x1 1645 MB/s [ 108.544401] raid6: sse2x2 2625 MB/s [ 108.616313] raid6: sse2x4 2850 MB/s [ 108.620688] raid6: using algorithm sse2x4 (2850 MB/s) [ 108.626500] md: raid6 personality registered for level 6 [ 108.632578] md: raid5 personality registered for level 5 [ 108.638652] md: raid4 personality registered for level 4 [ 108.665458] md: raid10 personality registered for level 10 Done. Begin: Running /scripts/init-premount ... Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. Begin: Waiting for root file system... ... [ 109.316078] tg3.c:v3.77 (May 31, 2007) [ 109.347624] SCSI subsystem initialized [ 109.395759] eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:2b:66:8a [ 109.410295] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] [ 109.418826] eth0: dma_rwctrl[769f4000] dma_mask[64-bit] [ 109.454822] usbcore: registered new interface driver usbfs [ 109.462358] usbcore: registered new interface driver hub [ 109.468490] usbcore: registered new device driver usb [ 109.494641] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 109.501588] e100: Copyright(c) 1999-2006 Intel Corporation [ 109.528042] eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:2b:66:8b [ 109.542585] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] [ 109.551109] eth1: dma_rwctrl[769f4000] dma_mask[64-bit] [ 109.562547] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 109.569774] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 109.579975] AMD8111: IDE controller at PCI slot 0000:01:04.1 [ 109.586474] AMD8111: chipset revision 3 [ 109.590945] AMD8111: not 100% native mode: will probe irqs later [ 109.597830] AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller [ 109.604413] ide0: BM-DMA at 0x3420-0x3427, BIOS settings: hda:pio, hdb:pio [ 109.613143] ide1: BM-DMA at 0x3428-0x342f, BIOS settings: hdc:pio, hdd:pio [ 110.761866] ohci_hcd 0000:04:00.0: OHCI Host Controller [ 110.768235] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1 [ 110.776709] ohci_hcd 0000:04:00.0: irq 19, io mem 0xfd020000 [ 110.844081] usb usb1: configuration #1 chosen from 1 choice [ 110.850634] hub 1-0:1.0: USB hub found [ 110.855030] hub 1-0:1.0: 3 ports detected [ 110.965891] ohci_hcd 0000:04:00.1: OHCI Host Controller [ 110.972065] ohci_hcd 0000:04:00.1: new USB bus registered, assigned bus number 2 [ 110.980481] ohci_hcd 0000:04:00.1: irq 19, io mem 0xfd021000 [ 111.047787] usb usb2: configuration #1 chosen from 1 choice [ 111.054329] hub 2-0:1.0: USB hub found [ 111.058704] hub 2-0:1.0: 3 ports detected [ 111.293494] e100: eth2: e100_probe: addr 0xfd023000, irq 18, MAC addr 00:E0:81:2B:66:2C [ 111.305088] scsi0 : sata_sil24 [ 111.308950] scsi1 : sata_sil24 [ 111.312788] scsi2 : sata_sil24 [ 111.316580] scsi3 : sata_sil24 [ 111.320404] ata1: SATA max UDMA/100 cmd 0xffffc20000ae0000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 28 [ 111.332014] ata2: SATA max UDMA/100 cmd 0xffffc20000ae2000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 28 [ 111.343569] ata3: SATA max UDMA/100 cmd 0xffffc20000ae4000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 28 [ 111.355136] ata4: SATA max UDMA/100 cmd 0xffffc20000ae6000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 28 [ 111.680595] ata1: SATA link down (SStatus 0 SControl 300) [ 112.000207] ata2: SATA link down (SStatus 0 SControl 300) [ 112.423718] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 112.435106] ata3.00: ATA-6: WDC WD2500SD-01KCB0, 08.02D08, max UDMA/133 [ 112.442633] ata3.00: 488397168 sectors, multi 0: LBA48 [ 112.454285] ata3.00: configured for UDMA/100 [ 112.875172] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 112.886524] ata4.00: ATA-6: WDC WD2500SD-01KCB0, 08.02D08, max UDMA/133 [ 112.894058] ata4.00: 488397168 sectors, multi 0: LBA48 [ 112.905733] ata4.00: configured for UDMA/100 [ 112.910800] scsi 2:0:0:0: Direct-Access ATA WDC WD2500SD-01K 08.0 PQ: 0 ANSI: 5 [ 112.920441] scsi 3:0:0:0: Direct-Access ATA WDC WD2500SD-01K 08.0 PQ: 0 ANSI: 5 [ 112.930235] sata_sil 0000:04:05.0: Applying R_ERR on DMA activate FIS errata fix [ 112.938763] scsi4 : sata_sil [ 112.942396] scsi5 : sata_sil [ 112.946005] scsi6 : sata_sil [ 112.949618] scsi7 : sata_sil [ 112.953224] ata5: SATA max UDMA/100 cmd 0xffffc20000a9e080 ctl 0xffffc20000a9e08a bmdma 0xffffc20000a9e000 irq 19 [ 112.964775] ata6: SATA max UDMA/100 cmd 0xffffc20000a9e0c0 ctl 0xffffc20000a9e0ca bmdma 0xffffc20000a9e008 irq 19 [ 112.976345] ata7: SATA max UDMA/100 cmd 0xffffc20000a9e280 ctl 0xffffc20000a9e28a bmdma 0xffffc20000a9e200 irq 19 [ 112.987916] ata8: SATA max UDMA/100 cmd 0xffffc20000a9e2c0 ctl 0xffffc20000a9e2ca bmdma 0xffffc20000a9e208 irq 19 [ 113.013368] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) [ 113.022028] sd 2:0:0:0: [sda] Write Protect is off [ 113.027540] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 113.037876] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) [ 113.045979] sd 2:0:0:0: [sda] Write Protect is off [ 113.051512] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 113.061767] sda: sda1 [ 113.082932] sd 2:0:0:0: [sda] Attached SCSI disk [ 113.088462] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB) [ 113.096594] sd 3:0:0:0: [sdb] Write Protect is off [ 113.102120] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 113.112388] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB) [ 113.121250] sd 3:0:0:0: [sdb] Write Protect is off [ 113.126803] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 113.137027] sdb: sdb1 [ 113.152335] sd 3:0:0:0: [sdb] Attached SCSI disk [ 113.163288] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 113.171836] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 113.279277] md: md0 stopped. [ 113.305761] md: md1 stopped. [ 113.323937] md: md2 stopped. [ 113.345966] md: md0 stopped. [ 113.352969] md: md1 stopped. [ 113.359446] md: md2 stopped. [ 113.522423] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 113.541202] ata5.00: Host Protected Area detected: [ 113.541204] current size: 488395055 sectors [ 113.541205] native size: 488397168 sectors [ 113.558743] ata5.00: native size increased to 488397168 sectors [ 113.565494] ata5.00: ATA-6: WDC WD2500SD-01KCB0, 08.02D08, max UDMA/133 [ 113.573033] ata5.00: 488397168 sectors, multi 0: LBA48 [ 113.601173] ata5.00: configured for UDMA/100 [ 114.073759] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 114.092577] ata6.00: ATA-6: WDC WD2500SD-01KCB0, 08.02D08, max UDMA/133 [ 114.100086] ata6.00: 488397168 sectors, multi 0: LBA48 [ 114.128504] ata6.00: configured for UDMA/100 [ 114.445263] ata7: SATA link down (SStatus 0 SControl 310) [ 114.764871] ata8: SATA link down (SStatus 0 SControl 310) [ 114.772632] scsi 4:0:0:0: Direct-Access ATA WDC WD2500SD-01K 08.0 PQ: 0 ANSI: 5 [ 114.782279] sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) [ 114.790898] sd 4:0:0:0: [sdc] Write Protect is off [ 114.796447] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.806737] sd 4:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) [ 114.814829] sd 4:0:0:0: [sdc] Write Protect is off [ 114.823652] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.833886] sdc: sdc1 sdc2 sdc3 sdc4 [ 114.855406] sd 4:0:0:0: [sdc] Attached SCSI disk [ 114.861082] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 114.867246] scsi 5:0:0:0: Direct-Access ATA WDC WD2500SD-01K 08.0 PQ: 0 ANSI: 5 [ 114.876811] sd 5:0:0:0: [sdd] 488397168 512-byte hardware sectors (250059 MB) [ 114.884921] sd 5:0:0:0: [sdd] Write Protect is off [ 114.890454] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.902331] sd 5:0:0:0: [sdd] 488397168 512-byte hardware sectors (250059 MB) [ 114.910471] sd 5:0:0:0: [sdd] Write Protect is off [ 114.916008] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.926273] sdd: sdd1 sdd2 sdd3 sdd4 [ 114.944510] sd 5:0:0:0: [sdd] Attached SCSI disk [ 114.950203] sd 5:0:0:0: Attached scsi generic sg3 type 0 [ 115.098650] md: md0 stopped. [ 115.152778] md: bind<sdd1> [ 115.156094] md: md1 stopped. [ 115.204148] md: bind<sdd2> [ 115.207432] md: md2 stopped. [ 115.218368] md: bind<sdd3> [ 115.221810] md: bind<sdc3> [ 115.232689] raid1: raid set md2 active with 2 out of 2 mirrors [ 115.312156] md: md0 stopped. [ 115.316371] md: unbind<sdd1> [ 115.319787] md: export_rdev(sdd1) [ 115.331137] md: bind<sdd1> [ 115.334570] md: bind<sdc1> [ 115.345405] raid1: raid set md0 active with 2 out of 2 mirrors [ 115.352603] md: md1 stopped. [ 115.356030] md: unbind<sdd2> [ 115.359449] md: export_rdev(sdd2) [ 115.413337] md: bind<sdd2> [ 115.416820] md: bind<sdc2> [ 115.427627] raid1: raid set md1 active with 2 out of 2 mirrors Done. Begin: Running /scripts/local-premount ... kinit: name_to_d[ 115.521397] Attempting manual resume ev_t(/dev/disk/by-uuid/d92cf937-a976-4e29-b445-3e26ecd99a0b) = md2(9,2) kinit: trying to resume from /dev/disk/by-uuid/d92cf937-a976-4e29-b445-3e26ecd99a0b kinit: No resume image, doing normal boot... Done. [ 115.560473] kjournald starting. Commit interval 5 seconds [ 115.566761] EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. * Reading files needed to boot... [ OK ] * Preparing restricted drivers... [ OK ] * Setting the system clock * Starting basic networking... [ OK ] * Starting kernel event manager... [ OK ] * Loading hardware drivers... [ 120.031129] NET: Registered protocol family 10 [ 120.036350] lo: Disabled Privacy Extensions [ 120.041356] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 120.234849] md: bind<sdb1> [ 120.238202] md: bind<sda1> [ 120.302917] raid1: raid set md5 active with 2 out of 2 mirrors [ 121.391558] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 121.409864] shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0 [ 121.417402] shpchp: shpc_init: cannot reserve MMIO region [ 121.423630] shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0 [ 121.431148] shpchp: shpc_init: cannot reserve MMIO region [ 121.437346] shpchp: HPC vendor_id 1022 device_id 7460 ss_vid 0 ss_did 0 [ 121.444884] shpchp: shpc_init: cannot reserve MMIO region [ 121.451092] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 121.498772] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 121.505130] tg3: eth0: Flow control is on for TX and on for RX. [ 121.514078] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 122.056952] AMD768 RNG detected [ 123.436275] input: ImExPS/2 Generic Explorer Mouse as /class/input/input2 [ OK ] * Setting the system clock * Loading kernel modules... * Loading manual drivers... [ 124.511953] lp: driver loaded but no devices found [ OK ] * Activating swap... [ OK ] * Checking root file system... fsck 1.40.2 (12-Jul-2007) /dev/md1: clean, 166379/1221600 files, 762323/2441856 blocks [ OK ] * Checking file systems... fsck 1.40.2 (12-Jul-2007) /dev/md0: clean, 55/124928 files, 106459/497856 blocks [ OK ] * Mounting local filesystems... [ OK ] * Activating swapfile swap... [ OK ] $Mounting securityfs on /sys/kernel/security: done. Loading AppArmor profiles : done. * Checking minimum space in /tmp... [ OK ] * Configuring network interfaces... [ OK ] * Setting console screen modes and fonts * Starting system log daemon... [ OK ] * Starting kernel log daemon... [ OK ] * Starting OpenBSD Secure Shell server sshd [ OK ] * Starting MTA [ OK ] FATAL: Error inserting battery (/lib/modules/2.6.22-14-generic/kernel/drivers/acpi/battery.ko): No such device * Starting powernowd... /etc/rc2.d/S20powernowd: 156: cannot create /sys/devices/system/cpu/cpu0//cpufreq/scaling_governor: Directory nonexistent * CPU frequency scaling not supported [ OK ] * sadc not enabled in /etc/default/sysstat, not starting. * Starting MD monitoring service mdadm --monitor [ OK ] grep: /proc/xen/capabilities: No such file or directory * Starting anac(h)ronistic cron anacron [ OK ] * Starting deferred execution scheduler atd [ OK ] * Starting periodic command scheduler crond [ OK ] * Enabling additional executable binary formats binfmt-support [ OK ] * Enabling laptop mode... [ OK ] * Running local boot scripts (/etc/rc.local) [ OK ]