Author: cozzie Date: 2008-10-14 20:26:09 +0200 (Tue, 14 Oct 2008) New Revision: 928
Added: coreboot-v3/southbridge/via/ coreboot-v3/southbridge/via/vt8237/ coreboot-v3/southbridge/via/vt8237/Makefile coreboot-v3/southbridge/via/vt8237/stage1.c coreboot-v3/southbridge/via/vt8237/vt8237.h Log: Add stage1 support for vt8237[RS] to v3.
Signed-off-by: Corey Osgood corey.osgood@gmail.com Acked-by: Carl-Daniel Hailfinger c-d.hailfinger.devel.2006@gmx.net
Added: coreboot-v3/southbridge/via/vt8237/Makefile =================================================================== --- coreboot-v3/southbridge/via/vt8237/Makefile (rev 0) +++ coreboot-v3/southbridge/via/vt8237/Makefile 2008-10-14 18:26:09 UTC (rev 928) @@ -0,0 +1,25 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 Corey Osgood corey.osgood@gmail.com +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +ifeq ($(CONFIG_SOUTHBRIDGE_VIA_VT8237),y) + +STAGE2_CHIPSET_SRC += + +endif
Added: coreboot-v3/southbridge/via/vt8237/stage1.c =================================================================== --- coreboot-v3/southbridge/via/vt8237/stage1.c (rev 0) +++ coreboot-v3/southbridge/via/vt8237/stage1.c 2008-10-14 18:26:09 UTC (rev 928) @@ -0,0 +1,318 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007-2008 Corey Osgood corey.osgood@gmail.com + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <types.h> +#include <lib.h> +#include <console.h> +#include <device/pci.h> +#include <io.h> +#include <device/pci_ids.h> +#include <spd.h> +#include "vt8237.h" + +/* TODO List: + * * Merge the rest of the functions from v2, except smbus_fixup which doesn't + * seem to be necessary any more (?) + * * Clean up vt8237_early_network_init. + * Comments in code indicate that it's broken? + * * Figure out if the smbus actually needs to be reset after every transaction. + */ + +/** + * Print an error, should it occur. If no error, just exit. + * + * @param host_status The data returned on the host status register after + * a transaction is processed. + * @param loops The number of times a transaction was attempted. + */ +static void smbus_print_error(u8 host_status, int loops) +{ + /* Check if there actually was an error. */ + if ((host_status == 0x00 || host_status == 0x40 || + host_status == 0x42) && (loops < SMBUS_TIMEOUT)) + { + printk(BIOS_SPEW, "SMBus Ready/Completed Successfully\n"); + return; + } + if (loops >= SMBUS_TIMEOUT) + printk(BIOS_ERR, "SMBus Timed out\n"); + if (host_status & (1 << 4)) + printk(BIOS_ERR, "Interrupt/SMI# was Failed Bus Transaction\n"); + if (host_status & (1 << 3)) + printk(BIOS_ERR, "Bus error\n"); + if (host_status & (1 << 2)) + printk(BIOS_ERR, "Device error\n"); + if (host_status & (1 << 1)) + printk(BIOS_SPEW, "Interrupt/SMI# completed successfully\n"); + if (host_status & (1 << 0)) + printk(BIOS_ERR, "Host busy\n"); +} + +/** + * Reset and take ownership of the SMBus. + */ +static void smbus_reset(u16 smbus_io_base) +{ + outb(HOST_RESET, smbus_io_base + SMBHSTSTAT); + + /* Datasheet says we have to read it to take ownership of SMBus. */ + smbus_print_error(inb(smbus_io_base + SMBHSTSTAT), 0); +} + +/** + * Wait for the SMBus to become ready to process the next transaction. + */ +static void smbus_wait_until_ready(u16 smbus_io_base) +{ + int loops; + + printk(BIOS_SPEW, "Waiting until SMBus ready\n"); + + loops = 0; + while ((inb(smbus_io_base + SMBHSTSTAT) & 1) == 1 && loops <= SMBUS_TIMEOUT) + ++loops; + + smbus_print_error(inb(smbus_io_base + SMBHSTSTAT), loops); +} + +/** + * Read a byte from the SMBus. + * + * @param dimm The address location of the DIMM on the SMBus. + * @param offset The offset the data is located at. + */ +u8 smbus_read_byte(u16 dimm, u8 offset, u16 smbus_io_base) +{ + u8 val; + + printk(BIOS_SPEW, "SMBus Read from DIMM %d at address 0x%x\n", + (int)dimm, offset); + + smbus_reset(smbus_io_base); + + /* Clear host data port. */ + outb(0x00, smbus_io_base + SMBHSTDAT0); + /* Doesn't seem to be necessary...*/ + /* udelay(1); */ + smbus_wait_until_ready(smbus_io_base); + + /* With this, addresses are 0x50, 0x51, etc. Without it, + * addresses would be 0xa1, 0xa3, etc */ + dimm = (dimm << 1) | 1; + + outb(dimm, smbus_io_base + SMBXMITADD); + outb(offset, smbus_io_base + SMBHSTCMD); + + /* Start transaction, byte data read. */ + outb(0x48, smbus_io_base + SMBHSTCTL); + /* udelay(1); */ + smbus_wait_until_ready(smbus_io_base); + + val = inb(smbus_io_base + SMBHSTDAT0); + printk(BIOS_SPEW, "Read: 0x%x\n", val); + + /* TODO: Is this necessary? */ + smbus_reset(smbus_io_base); + + return val; +} + +/** + * Enable the smbus on vt8237-based systems + * + * @param smbus_io_base: The SMBus I/O base, usually 0x400 + */ +void enable_smbus(u16 smbus_io_base) +{ + u32 dev; + + /* Power management controller */ + pci_conf1_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237R_LPC, + &dev); + + if (!dev) { + /* Power management controller */ + pci_conf1_find_device(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_VT8237S_LPC, &dev); + if (!dev) + { + printk(BIOS_ERR, "Power management controller not " + "found! Using hardcoded default.\n"); + dev = PCI_BDF(0, 17, 0); + } else { + printk(BIOS_DEBUG, "VT8237S Power management " + "controller found at 0x%x\n", dev); + } + } else { + printk(BIOS_DEBUG, "VT8237R Power management controller found " + "at 0x%x\n", dev); + } + + /* 7 = SMBus Clock from RTC 32.768KHz + * 5 = Internal PLL reset from susp + */ + pci_conf1_write_config8(dev, VT8237R_POWER_WELL, 0xa0); + + /* Enable SMBus. */ + pci_conf1_write_config16(dev, VT8237R_SMBUS_IO_BASE_REG, + smbus_io_base | 0x1); + + /* SMBus Host Configuration, enable. */ + pci_conf1_write_config8(dev, VT8237R_SMBUS_HOST_CONF, 0x01); + + /* Make it work for I/O. */ + pci_conf1_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO); + + /* reset smbus */ + smbus_reset(smbus_io_base); + + /* Reset the internal pointer. */ + inb(smbus_io_base + SMBHSTCTL); +} + +/* TODO: + * Magic numbers -> #defines + * fix? + * clean up + */ + +/* offset 0x58 + * 31:20 reserved + * 19:16 4 bit position in shadow EEPROM + * 15:0 data to write + * + * offset 0x5c + * 31:28 reserved + * 27 ERDBG - enable read from 0x5c + * 26 reserved + * 25 SEELD + * 24 SEEPR - write 1 when done updating, wait until SEELD is set to 1, sticky + * cleared by reset, if it is 1 writing is disabled + * 19:16 4 bit position in shadow EEPROM + * 15:0 data from shadow EEPROM + * + * after PCIRESET SEELD and SEEPR must be 1 and 1 +*/ + +/* 1 = needs PCI reset, 0 don't reset, network initialized */ + +/* fixme maybe close the debug register after use? */ + +#define LAN_TIMEOUT 0x7FFFFFFF + +int vt8237_early_network_init(struct vt8237_network_rom *rom) { + struct vt8237_network_rom n; + int loops = 0; + u32 dev; + u32 tmp; + u8 status; + u16 *rom_write; + unsigned int checksum; + int i; + + /* Network adapter */ + pci_conf1_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237_LAN, + &dev); + + if (!dev) { + printk(BIOS_ERR, "Network is disabled, please enable\n"); + return 0; + } + + tmp = pci_conf1_read_config32(dev, 0x5c); + /* enable ERDBG */ + tmp |= 0x08000000; + pci_conf1_write_config32(dev, 0x5c, tmp); + + status = ((pci_conf1_read_config32(dev, 0x5c) >> 24) & 0x3); + + if (status == 3) { + /* network controller OK, EEPROM loaded */ + return 0; + } + + if (rom == NULL) { + printk(BIOS_ERR, "No configuration data specified, using default MAC!\n"); + n.mac_address[0] = 0x0; + n.mac_address[1] = 0x0; + n.mac_address[2] = 0xde; + n.mac_address[3] = 0xad; + n.mac_address[4] = 0xbe; + n.mac_address[5] = 0xef; + n.phy_addr = 0x1; + n.res1 = 0x0; + n.sub_sid = 0x102; + n.sub_vid = 0x1106; + n.pid = 0x3065; + n.vid = 0x1106; + n.pmcc = 0x1f; + n.data_sel = 0x10; + n.pmu_data_reg = 0x0; + n.aux_curr = 0x0; + n.reserved = 0x0; + n.min_gnt = 0x3; + n.max_lat = 0x8; + n.bcr0 = 0x9; + n.bcr1 = 0xe; + n.cfg_a = 0x3; + n.cfg_b = 0x0; + n.cfg_c = 0x40; + n.cfg_d = 0x82; + n.checksum = 0x0; + rom = &n; + } + + rom_write = (u16 *) rom; + checksum = 0; + /* write all data except checksum and second to last byte */ + tmp &= 0xff000000; /* leave reserved bits in */ + for (i = 0; i < 15; i++) { + pci_conf1_write_config32(dev, 0x58, tmp | (i << 16) | rom_write[i]); + /* lame code fixme */ + checksum += rom_write[i] & 0xff; + //checksum %= 256; + checksum += (rom_write[i] >> 8) & 0xff; + //checksum %= 256; + } + + checksum += (rom_write[15] & 0xff); + checksum = ~(checksum & 0xff); + tmp |= (((checksum & 0xff) << 8) | rom_write[15]); + + /* write last byte and checksum */ + pci_conf1_write_config32(dev, 0x58, (15 << 16) | tmp); + + tmp = pci_conf1_read_config32(dev, 0x5c); + pci_conf1_write_config32(dev, 0x5c, tmp | 0x01000000); /* toggle SEEPR */ + + /* Yes, this is a mess, but it's the easiest way to do it. */ + while ( (((pci_conf1_read_config32(dev, 0x5c) >> 25) & 1) == 0) + && (loops < LAN_TIMEOUT)) + ++loops; + + if (loops >= LAN_TIMEOUT) { + printk(BIOS_ERR, "Timout - LAN controller did not accept configuration\n"); + return 0; + } + + /* we are done, config will be used after PCIRST# */ + return 1; +}
Added: coreboot-v3/southbridge/via/vt8237/vt8237.h =================================================================== --- coreboot-v3/southbridge/via/vt8237/vt8237.h (rev 0) +++ coreboot-v3/southbridge/via/vt8237/vt8237.h 2008-10-14 18:26:09 UTC (rev 928) @@ -0,0 +1,90 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef SOUTHBRIDGE_VIA_VT8237_VT8237_H +#define SOUTHBRIDGE_VIA_VT8237_VT8237_H + +#include <types.h> + +/* Static resources for the VT8237R southbridge */ + +#define VT8237R_APIC_ID 0x2 +#define VT8237R_ACPI_IO_BASE 0x500 +/* 0x0 disabled, 0x2 reserved, 0xf = IRQ15 */ +#define VT8237R_ACPI_IRQ 0x9 +#define VT8237S_SPI_MEM_BASE 0xfed02000ULL +#define VT8237R_HPET_ADDR 0xfed00000ULL +#define VT8237R_APIC_BASE 0xfec00000ULL + +/* IDE */ +#define IDE_CS 0x40 +#define IDE_CONF_I 0x41 +#define IDE_CONF_II 0x42 +#define IDE_CONF_FIFO 0x43 +#define IDE_MISC_I 0x44 +#define IDE_MISC_II 0x45 +#define IDE_UDMA 0x50 + +/* SMBus */ +#define VT8237R_POWER_WELL 0x94 +#define VT8237R_SMBUS_IO_BASE_REG 0xd0 +#define VT8237R_SMBUS_HOST_CONF 0xd2 + +#define SMBHSTSTAT 0x0 +#define SMBSLVSTAT 0x1 +#define SMBHSTCTL 0x2 +#define SMBHSTCMD 0x3 +#define SMBXMITADD 0x4 +#define SMBHSTDAT0 0x5 + +#define HOST_RESET 0xff +/* 1 in the 0 bit of SMBHSTADD states to READ. */ +#define READ_CMD 0x01 +#define SMBUS_TIMEOUT (100 * 1000 * 10) +#define I2C_TRANS_CMD 0x40 +#define CLOCK_SLAVE_ADDRESS 0x69 + +struct vt8237_network_rom { + u8 mac_address[6]; + u8 phy_addr; + u8 res1; + u16 sub_sid; + u16 sub_vid; + u16 pid; + u16 vid; + u8 pmcc; + u8 data_sel; + u8 pmu_data_reg; + u8 aux_curr; + u16 reserved; + u8 min_gnt; + u8 max_lat; + u8 bcr0; + u8 bcr1; + u8 cfg_a; + u8 cfg_b; + u8 cfg_c; + u8 cfg_d; + u8 checksum; +} __attribute__ ((packed)); + +void enable_smbus(u16); +u8 smbus_read_byte(u16, u8, u16); + +#endif