Author: stepan Date: 2007-11-03 00:17:57 +0100 (Sat, 03 Nov 2007) New Revision: 2934
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Config.lb trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Options.lb trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/acpi_tables.c trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/chip.h trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cmos.layout trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/dsdt.asl trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/fadt.c trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mainboard.c trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mptable.c trunk/LinuxBIOSv2/targets/asus/a8v-e_se/ trunk/LinuxBIOSv2/targets/asus/a8v-e_se/Config.lb Log: Asus A8V-E-SE support from Rudolf Marek
Signed-off-by: Rudolf Marek r.marek@assembler.cz Acked-by: Stefan Reinauer stepan@coresystems.de
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Config.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Config.lb (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Config.lb 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,274 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2007 AMD +## Written by Yinghai Lu yinghailu@amd.com for AMD. +## +## Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus bootloader) will live in the boot rom chip. +## + if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) + else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 + end + +## +## Compute the start location and size size of +## The linuxBIOS bootloader. +## +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) +default CONFIG_ROM_PAYLOAD = 1 + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +if HAVE_ACPI_TABLES + object acpi_tables.o + object fadt.o + makerule dsdt.c + depends "$(MAINBOARD)/dsdt.asl" + action "iasl -tc $(MAINBOARD)/dsdt.asl" + action "mv dsdt.hex dsdt.c" + end + object ./dsdt.o +end + +if HAVE_MP_TABLE object mptable.o end +if HAVE_PIRQ_TABLE object irq_tables.o end +#object reset.o +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + makerule ./cache_as_ram_auto.o + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" + end + else + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end + end + +end + +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## + +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/entry16.inc + ldscript /cpu/x86/16bit/entry16.lds + mainboardinit southbridge/via/k8t890/romstrap.inc + ldscript /southbridge/via/k8t890/romstrap.lds + +end + +mainboardinit cpu/x86/32bit/entry32.inc + +if USE_DCACHE_RAM + if CONFIG_USE_INIT + ldscript /cpu/x86/32bit/entry32.lds + end + + if CONFIG_USE_INIT + ldscript /cpu/amd/car/cache_as_ram.lds + end +end + + +## +## Build our reset vector (This is where linuxBIOS is entered) +## + +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +if USE_DCACHE_RAM + ## + ## Setup Cache-As-Ram + ## + mainboardinit cpu/amd/car/cache_as_ram.inc +end + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### + +if USE_FALLBACK_IMAGE + if USE_DCACHE_RAM + ldscript /arch/i386/lib/failover.lds + end +end + + +## +## Setup RAM +## +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + initobject cache_as_ram_auto.o + else + mainboardinit ./cache_as_ram_auto.inc + end +end + +## +## Include the secondary Configuration files +## +if CONFIG_CHIP_NAME + config chip.h +end + +chip northbridge/amd/amdk8/root_complex + device apic_cluster 0 on + chip cpu/amd/socket_939 + device apic 0 on end + end + end + + device pci_domain 0 on + chip northbridge/amd/amdk8 #mc0 + device pci 18.0 on # northbridge + # devices on link 0, link 0 == LDT 0 + chip southbridge/via/vt8237r + #both IDE channels + register "ide0_enable" = "1" + register "ide1_enable" = "1" + #both cables are 80pin + register "ide0_80pin_cable" = "1" + register "ide1_80pin_cable" = "1" + #enables the functions of SB + register "fn_ctrl_lo" = "0" + register "fn_ctrl_hi" = "0xad" + + device pci 0.0 on end # HT + device pci f.1 on end # IDE + device pci 11.0 on # LPC + chip drivers/generic/generic #dimm 0-0-0 + device i2c 50 on end + end + chip drivers/generic/generic #dimm 0-0-1 + device i2c 51 on end + end + chip drivers/generic/generic #dimm 0-1-0 + device i2c 52 on end + end + chip drivers/generic/generic #dimm 0-1-1 + device i2c 53 on end + end + + chip superio/winbond/w83627ehg + device pnp 2e.0 on # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 on # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + drq 0x74 = 3 + end + device pnp 2e.2 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.3 off # Com2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.5 off #keyb OFF + end + device pnp 2e.6 off # SERIAL_FLASH + io 0x60 = 0x100 + end + device pnp 2e.7 off # GAME_MIDI_GIPO1 + # io 0x60 = 0x220 + # io 0x62 = 0x300 + # irq 0x70 = a + end + device pnp 2e.8 off end # WDTO_PLED + device pnp 2e.9 off end # GPIO2_GPIO3_GPIO4_GPIO5 0x30 0x9 + #GPIO 5 and 2 active + #0xe0 = de + #0xe1 = 01 + #0xe2 = 00 + #0xe3 = 03 + #0xe4 = a4 + #0xe5 = 00 + + device pnp 2e.a off end # ACPI + device pnp 2e.b on # HW Monitor + io 0x60 = 0x290 + irq 0x70 = 0 + end + end #end SIO + end #end 11 + + device pci 12.0 off end # VIA LAN is disabled, Asus used other chip + end + + chip southbridge/via/k8t890 + end + + end # device pci 18.0 + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end #mc0 + + end # pci_domain + +end # root_complex
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Options.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Options.lb (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/Options.lb 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,313 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License v2 as published by +## the Free Software Foundation. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_PAYLOAD +uses CONFIG_ROM_PAYLOAD_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +##uses USE_OPTION_TABLE +##uses CONFIG_LB_MEM_TOPK + +uses HAVE_ACPI_TABLES + +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +#bx_b001- uses K8_HW_MEM_HOLE_SIZEK +uses K8_HT_FREQ_1G_SUPPORT + +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_USE_INIT + +uses ENABLE_APIC_EXT_ID +uses APIC_ID_OFFSET +uses LIFT_BSP_APIC_ID + +uses HT_CHAIN_UNITID_BASE +uses HT_CHAIN_END_UNITID_BASE +#bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0 +uses SB_HT_CHAIN_UNITID_OFFSET_ONLY +#bx_b005+ +uses SB_HT_CHAIN_ON_BUS0 + +## ROM_SIZE is the size of boot ROM that this board will use. +#512K bytes +default ROM_SIZE=512 * 1024 + +#1M bytes +#bx- default ROM_SIZE=1024 * 1024 + +## +## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use +## +#256K +default FALLBACK_SIZE=256 * 1024 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=0 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=0 +default IRQ_SLOT_COUNT=11 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=0 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 +default CONFIG_MAX_PHYSICAL_CPUS=1 +default CONFIG_LOGICAL_CPUS=1 + +#acpi +default HAVE_ACPI_TABLES=1 + +#CHIP_NAME ? +#default CONFIG_CHIP_NAME=1 + +#1G memory hole +#bx_b001- default K8_HW_MEM_HOLE_SIZEK=0x100000 + +#Opteron K8 1G HT Support +default K8_HT_FREQ_1G_SUPPORT=1 + +##HT Unit ID offset, default is 1, the typical one +default HT_CHAIN_UNITID_BASE=0x0 + +##real SB Unit ID, default is 0x20, mean dont touch it at last +#default HT_CHAIN_END_UNITID_BASE=0x0 + +#make the SB HT chain on bus 0, default is not (0) +#bx_b001- default K8_SB_HT_CHAIN_ON_BUS0=2 + +##bx_b005+ make the SB HT chain on bus 0 +default SB_HT_CHAIN_ON_BUS0=1 + +##only offset for SB chain?, default is yes(1) +default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 + +#VGA +default CONFIG_CONSOLE_VGA=1 +default CONFIG_PCI_ROM_RUN=1 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xcc000 +default DCACHE_RAM_SIZE=0x4000 +default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 +default CONFIG_USE_INIT=0 + +default ENABLE_APIC_EXT_ID=0 +default APIC_ID_OFFSET=0x10 +default LIFT_BSP_APIC_ID=0 + + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="A8V-E SE" +default MAINBOARD_VENDOR="ASUS" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1043 +#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1234 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 64 * 1024 + +## +## Use a small 8K stack +## +default STACK_SIZE= 8 * 1024 + +## +## Use a small 256K heap +## +default HEAP_SIZE=256 * 1024 + +#more 1M for pgtbl +##default CONFIG_LB_MEM_TOPK=2048 + +## +## Only use the option table in a normal image +## +##default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00004000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_PAYLOAD = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/acpi_tables.c =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/acpi_tables.c (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/acpi_tables.c 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,169 @@ +/* + * This file is part of the LinuxBIOS project. + * written by Stefan Reinauer stepan@openbios.org + * ACPI FADT, FACS, and DSDT table support added by + * + * Copyright (C) 2004 Stefan Reinauer stepan@openbios.org + * Copyright (C) 2005 Nick Barker nick.barker9@btinternet.com + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <string.h> +#include <arch/acpi.h> +#include <arch/smp/mpspec.h> +#include <device/device.h> +#include <device/pci_ids.h> + +#include <../../../southbridge/via/vt8237r/vt8237r.h> +#include <../../../southbridge/via/k8t890/k8t890.h> + +extern unsigned char AmlCode[]; + +unsigned long acpi_fill_mcfg(unsigned long current) +{ + device_t dev; + struct resource *res; + dev = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_K8T890CE_5, 0); + if (!dev) + return current; + + res = find_resource(dev, K8T890_MMCONFIG_MBAR); + if (res) { + current += acpi_create_mcfg_mmconfig((acpi_mcfg_mmconfig_t *) + current, res->base, 0x0, 0x0, 0xff); + } + return current; +} + +unsigned long acpi_fill_madt(unsigned long current) +{ + unsigned int gsi_base = 0x18; + + /* create all subtables for processors */ + current = acpi_create_madt_lapics(current); + + /* Write SB IOAPIC */ + current += + acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, VT8237R_APIC_ID, + VT8237R_APIC_BASE, 0); + + /* Write NB IOAPIC */ + current += + acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, K8T890_APIC_ID, + K8T890_APIC_BASE, gsi_base); + /* IRQ9 ACPI active low */ + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) + current, 0, 9, 9, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_LOW); + + /* IRQ0 -> APIC IRQ2 */ + current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) + current, 0, 0, 2, 0x0); + + /* create all subtables for processors */ + current = + acpi_create_madt_lapic_nmis(current, + MP_IRQ_TRIGGER_EDGE | + MP_IRQ_POLARITY_HIGH, 1); + + return current; +} + + +unsigned long write_acpi_tables(unsigned long start) +{ + unsigned long current; + acpi_rsdp_t *rsdp; + acpi_srat_t *srat; + acpi_rsdt_t *rsdt; + acpi_mcfg_t *mcfg; + acpi_hpet_t *hpet; + acpi_madt_t *madt; + acpi_fadt_t *fadt; + acpi_facs_t *facs; + acpi_header_t *dsdt; + + /* Align ACPI tables to 16byte */ + start = (start + 0x0f) & -0x10; + current = start; + + printk_info("ACPI: Writing ACPI tables at %lx...\n", start); + + /* We need at least an RSDP and an RSDT Table */ + rsdp = (acpi_rsdp_t *) current; + current += sizeof(acpi_rsdp_t); + rsdt = (acpi_rsdt_t *) current; + current += sizeof(acpi_rsdt_t); + + /* clear all table memory */ + memset((void *) start, 0, current - start); + + acpi_write_rsdp(rsdp, rsdt); + acpi_write_rsdt(rsdt); + + /* + * We explicitly add these tables later on: + */ + printk_debug("ACPI: * FACS\n"); + facs = (acpi_facs_t *) current; + current += sizeof(acpi_facs_t); + acpi_create_facs(facs); + + dsdt = (acpi_header_t *) current; + current += ((acpi_header_t *) AmlCode)->length; + memcpy((void *) dsdt, (void *) AmlCode, + ((acpi_header_t *) AmlCode)->length); + dsdt->checksum = 0; // don't trust intel iasl compiler to get this right + dsdt->checksum = acpi_checksum(dsdt, dsdt->length); + printk_debug("ACPI: * DSDT @ %08x Length %x\n", dsdt, + dsdt->length); + printk_debug("ACPI: * FADT\n"); + + fadt = (acpi_fadt_t *) current; + current += sizeof(acpi_fadt_t); + + acpi_create_fadt(fadt, facs, dsdt); + acpi_add_table(rsdt, fadt); + + printk_debug("ACPI: * HPET\n"); + hpet = (acpi_hpet_t *) current; + current += sizeof(acpi_hpet_t); + acpi_create_hpet(hpet); + acpi_add_table(rsdt, hpet); + + /* If we want to use HPET Timers Linux wants an MADT */ + printk_debug("ACPI: * MADT\n"); + madt = (acpi_madt_t *) current; + acpi_create_madt(madt); + current += madt->header.length; + acpi_add_table(rsdt, madt); + + printk_debug("ACPI: * MCFG\n"); + mcfg = (acpi_mcfg_t *) current; + acpi_create_mcfg(mcfg); + current += mcfg->header.length; + acpi_add_table(rsdt, mcfg); + + /* SRAT */ + printk_debug("ACPI: * SRAT\n"); + srat = (acpi_srat_t *) current; + acpi_create_srat(srat); + current += srat->header.length; + acpi_add_table(rsdt, srat); + + printk_info("ACPI: done.\n"); + return current; +}
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,331 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu yinghailu@amd.com for AMD. + * Copyright (C) 2006 MSI + * Written by Bingxun Shi bingxunshi@gmail.com for MSI. + * + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define ASSEMBLY 1 +#define __ROMCC__ + +#define RAMINIT_SYSINFO 1 + +#define CACHE_AS_RAM_ADDRESS_DEBUG 0 + +unsigned int get_sbdn(unsigned bus); + +//used by raminit +#define QRANK_DIMM_SUPPORT 1 + +//used by init_cpus and fidvid +#define K8_SET_FIDVID 1 +//if we want to wait for core1 done before DQS training, set it to 0 +#define K8_SET_FIDVID_CORE0_ONLY 1 + +//#define DEBUG_SMBUS 1 + +#include <stdint.h> +#include <device/pci_def.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <cpu/x86/lapic.h> +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" + +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" + +#include <cpu/amd/model_fxx_rev.h> +#include "northbridge/amd/amdk8/raminit.h" +#include "cpu/amd/model_fxx/apic_timer.c" +#include "lib/delay.c" + +#if CONFIG_USE_INIT == 0 +#include "lib/memcpy.c" +#endif + +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/amd/amdk8/reset_test.c" +#include "northbridge/amd/amdk8/debug.c" +#include "northbridge/amd/amdk8/early_ht.c" + + +#include "superio/winbond/w83627ehg/w83627ehg_early_serial.c" +#include "southbridge/via/vt8237r/vt8237r_early_smbus.c" + +#include "cpu/amd/mtrr/amd_earlymtrr.c" +#include "cpu/x86/bist.h" + +#include "northbridge/amd/amdk8/setup_resource_map.c" + +#define SERIAL_DEV PNP_DEV(0x2e, W83627EHG_SP1) +#define GPIO_DEV PNP_DEV(0x2e, W83627EHG_GPIO_SUSLED) +#define RTC_DEV PNP_DEV(0x2e, W83627EHG_RTC) + +static void memreset_setup(void) +{ +} + +static void memreset(int controllers, const struct mem_controller *ctrl) +{ +} + + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#define K8_4RANK_DIMM_SUPPORT 1 + +#include "northbridge/amd/amdk8/amdk8.h" +#include "northbridge/amd/amdk8/raminit.c" +#include "northbridge/amd/amdk8/coherent_ht.c" +#include "northbridge/amd/amdk8/incoherent_ht.c" +#include "sdram/generic_sdram.c" + +#include "cpu/amd/dualcore/dualcore.c" + +#include "southbridge/via/k8t890/k8t890_early_car.c" + +#include "cpu/amd/car/copy_and_run.c" + +#include "cpu/amd/car/post_cache_as_ram.c" + +#include "cpu/amd/model_fxx/init_cpus.c" +#include "cpu/amd/model_fxx/fidvid.c" + +#include "northbridge/amd/amdk8/resourcemap.c" + + +void activate_spd_rom(const struct mem_controller *ctrl) +{ + +} + +void hard_reset(void) +{ + print_info("NO HARD RESET FIX ME!\n"); +} + +void soft_reset(void) +{ + uint8_t tmp; + set_bios_reset(); + print_debug("soft reset \r\n"); + + /* PCI reset */ + tmp = pci_read_config8(PCI_DEV(0, 0x11, 0), 0x4f); + tmp |= 0x01; + pci_write_config8(PCI_DEV(0, 0x11, 0), 0x4f, tmp); + + while (1) { + /* daisy daisy ... */ + hlt(); + } +} + +unsigned int get_sbdn(unsigned bus) +{ + device_t dev; + + dev = pci_locate_device_on_bus(PCI_ID(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_VT8237R_LPC), bus); + return (dev >> 15) & 0x1f; +} + +#if USE_FALLBACK_IMAGE == 1 + +void failover_process(unsigned long bist, unsigned long cpu_init_detectedx) +{ +// unsigned last_boot_normal_x = last_boot_normal(); +//FIXME + unsigned last_boot_normal_x = 1; + u8 reg; + + pnp_enter_ext_func_mode(SERIAL_DEV); + reg = pnp_read_config(SERIAL_DEV, 0x24); + pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); /* we have 24MHz input */ + + reg = pnp_read_config(SERIAL_DEV, 0x2A); + pnp_write_config(SERIAL_DEV, 0x2A, (reg | 1)); /* we have GPIO for KB/MS PIN */ + + reg = pnp_read_config(SERIAL_DEV, 0x2C); + pnp_write_config(SERIAL_DEV, 0x2C, (reg | 0xf0)); /* we have all RESTOUT and even some reserved bits too */ + + pnp_exit_ext_func_mode(SERIAL_DEV); + + pnp_enter_ext_func_mode(GPIO_DEV); + pnp_set_logical_device(GPIO_DEV); + pnp_write_config(GPIO_DEV, 0xe0, 0xde); // 1101110 0=output 1=input + pnp_write_config(GPIO_DEV, 0xe1, 0x1); //set output val + pnp_write_config(GPIO_DEV, 0xe2, 0x0); //no inversion + pnp_write_config(GPIO_DEV, 0xe3, 0x3); //0000 0011 0=output 1=input + pnp_write_config(GPIO_DEV, 0xe4, 0xa4); //set output val + pnp_write_config(GPIO_DEV, 0xe5, 0x0); //no inversion + pnp_write_config(GPIO_DEV, 0x30, 0x9); //Enable GPIO 2 & GPIO 5 + pnp_exit_ext_func_mode(GPIO_DEV); + + + w83627ehg_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + + print_info("now booting... fallback\r\n"); + + /* Is this a cpu only reset? or Is this a secondary cpu? */ + if ((cpu_init_detectedx) || (!boot_cpu())) { + if (last_boot_normal_x) { + goto normal_image; + } else { + goto fallback_image; + } + } + + /* Nothing special needs to be done to find bus 0 */ + /* Allow the HT devices to be found */ + + enumerate_ht_chain(); + + /* Is this a deliberate reset by the bios */ + if (bios_reset_detected() && last_boot_normal_x) { + goto normal_image; + } + /* This is the primary cpu how should I boot? */ + else if (do_normal_boot()) { + goto normal_image; + } else { + goto fallback_image; + } + normal_image: + //print_info("JMP normal image\r\n"); + + __asm__ volatile ("jmp __normal_image": /* outputs */ + :"a" (bist), "b"(cpu_init_detectedx) /* inputs */ + ); + + fallback_image: + ; +} +#endif + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx); + +void cache_as_ram_main(unsigned long bist, + unsigned long cpu_init_detectedx) +{ + +#if USE_FALLBACK_IMAGE == 1 + failover_process(bist, cpu_init_detectedx); +#endif + real_main(bist, cpu_init_detectedx); + +} + + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + static const uint16_t spd_addr[] = { + (0xa << 3) | 0, (0xa << 3) | 2, 0, 0, + (0xa << 3) | 1, (0xa << 3) | 3, 0, 0, +#if CONFIG_MAX_PHYSICAL_CPUS > 1 + (0xa << 3) | 4, (0xa << 3) | 6, 0, 0, + (0xa << 3) | 5, (0xa << 3) | 7, 0, 0, +#endif + }; + unsigned bsp_apicid = 0; + int needs_reset = 0; + struct sys_info *sysinfo = + (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - + DCACHE_RAM_GLOBAL_VAR_SIZE); + char *p; + u8 reg; + + pnp_enter_ext_func_mode(SERIAL_DEV); + reg = pnp_read_config(SERIAL_DEV, 0x24); + pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); /* we have 24MHz input */ + + reg = pnp_read_config(SERIAL_DEV, 0x2A); + pnp_write_config(SERIAL_DEV, 0x2A, (reg | 1)); /* we have GPIO for KB/MS PIN */ + + reg = pnp_read_config(SERIAL_DEV, 0x2C); + pnp_write_config(SERIAL_DEV, 0x2C, (reg | 0xf0)); /* we have all RESTOUT and even some reserved bits too */ + + pnp_exit_ext_func_mode(SERIAL_DEV); + + pnp_enter_ext_func_mode(GPIO_DEV); + pnp_set_logical_device(GPIO_DEV); + pnp_write_config(GPIO_DEV, 0xe0, 0xde); // 1101110 0=output 1=input + pnp_write_config(GPIO_DEV, 0xe1, 0x1); //set output val + pnp_write_config(GPIO_DEV, 0xe2, 0x0); //no inversion + pnp_write_config(GPIO_DEV, 0xe3, 0x3); //0000 0011 0=output 1=input + pnp_write_config(GPIO_DEV, 0xe4, 0xa4); //set output val + //0x10 seems to control something with SGD VIA + + pnp_write_config(GPIO_DEV, 0xe5, 0x0); //no inversion + pnp_write_config(GPIO_DEV, 0x30, 0x9); //Enable GPIO 2 & GPIO 5 + pnp_exit_ext_func_mode(GPIO_DEV); + + + w83627ehg_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + + print_info("now booting... real_main\r\n"); + + if (bist == 0) { + bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); + } + /* Halt if there was a built in self test failure */ + report_bist_failure(bist); + setup_default_resource_map(); + setup_coherent_ht_domain(); + wait_all_core0_started(); + print_info("now booting... Core0 started\r\n"); + +#if CONFIG_LOGICAL_CPUS==1 + // It is said that we should start core1 after all core0 launched + start_other_cores(); + wait_all_other_cores_started(bsp_apicid); +#endif + init_timer(); + ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); + + /* Fixme it assumes that 1000MHz LDT is selected. */ + needs_reset |= k8t890_early_setup_car(16, 0x6); + + if (needs_reset) { + print_debug("ht reset -\r\n"); + soft_reset(); + } + /* stop the APs so we can start them later in init */ + allow_all_aps_stop(bsp_apicid); + /* It's the time to set ctrl now; */ + fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); + enable_smbus(); + memreset_setup(); + sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); + post_cache_as_ram(); +} +
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/chip.h =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/chip.h (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/chip.h 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,24 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +extern struct chip_operations mainboard_asus_a8v_e_se_ops; + +struct mainboard_asus_a8v_e_se_config { + +};
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cmos.layout =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cmos.layout (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/cmos.layout 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,98 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +395 1 e 1 hw_scrubber +396 1 e 1 interleave_chip_selects +397 2 e 8 max_mem_clock +399 1 e 2 dual_core +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +440 4 e 9 slow_cpu +444 1 e 1 nmi +445 1 e 1 iommu +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 reserved_memory + + + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM +8 0 DDR400 +8 1 DDR333 +8 2 DDR266 +8 3 DDR200 +9 0 off +9 1 87.5% +9 2 75.0% +9 3 62.5% +9 4 50.0% +9 5 37.5% +9 6 25.0% +9 7 12.5% + +checksums + +checksum 392 983 984 + +
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/dsdt.asl =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/dsdt.asl (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/dsdt.asl 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,245 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Minimalist ACPI DSDT table for EPIA-M / MII + * (C) Copyright 2004 Nick Barker Nick.Barker9@btinternet.com + * + * (C) Copyright 2007 Rudolf Marek r.marek@assembler.cz + * + * ISA portions taken from QEMU acpi-dsdt.dsl + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + + +DefinitionBlock ("DSDT.aml", "DSDT", 1, "LXBIOS", "LXB-DSDT", 1) +{ + + + + + /* + * Define the main processor + */ + Scope (_PR) + { + Processor (_PR.CPU0, 0x00, 0x000000, 0x00) {} + Processor (_PR.CPU1, 0x01, 0x000000, 0x00) {} + } + + /* For now only define 2 power states: + * - S0 which is fully on + * - S5 which is soft off + * any others would involve declaring the wake up methods + */ + Name (_S0, Package () {0x00, 0x00, 0x00, 0x00 }) + Name (_S5, Package () {0x02, 0x02, 0x00, 0x00 }) + + /* Root of the bus hierarchy */ + Scope (_SB) + { + /* top PCI device */ + Device (PCI0) + { + Name (_HID, EisaId ("PNP0A03")) + Name (_ADR, 0x00) + Name (_UID, 0x00) + Name (_BBN, 0x00) + + /* PCI Routing Table */ + //aaa + Name (_PRT, Package () { + Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, //slot 0xB + Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 }, + Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 }, + Package (0x04) { 0x000BFFFF, 0x03, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x00, 0x00, 0x11 }, //Slot 0xC + Package (0x04) { 0x000CFFFF, 0x01, 0x00, 0x12 }, + Package (0x04) { 0x000CFFFF, 0x02, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x03, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x00, 0x00, 0x12 }, //Slot 0xD + Package (0x04) { 0x000DFFFF, 0x01, 0x00, 0x13 }, + Package (0x04) { 0x000DFFFF, 0x02, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x03, 0x00, 0x11 }, + Package (0x04) { 0x000F0000, 0x01, 0x00, 0x14 }, //0xf SATA IRQ 20 + Package (0x04) { 0x000F0001, 0x00, 0x00, 0x14 }, //0xf NAtive IDE IRQ 20 + Package (0x04) { 0x0010FFFF, 0x00, 0x00, 0x15 }, //USB routing + Package (0x04) { 0x0010FFFF, 0x01, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x02, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x03, 0x00, 0x15 }, + Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 }, //AC97 MC97 + Package (0x04) { 0x0002FFFF, 0x00, 0x00, 0x1B }, //PCIE16 bridge IRQ27 + Package (0x04) { 0x0002FFFF, 0x01, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x02, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x03, 0x00, 0x1B }, + Package (0x04) { 0x0003FFFF, 0x00, 0x00, 0x1F }, //PCIE bridge IRQ31 + Package (0x04) { 0x0003FFFF, 0x01, 0x00, 0x23 }, //IRQ36 + Package (0x04) { 0x0003FFFF, 0x02, 0x00, 0x27 }, //IRQ39 + Package (0x04) { 0x0003FFFF, 0x03, 0x00, 0x2B } //IRQ43 + }) + + + Device (PEGG) + { + Name (_ADR, 0x00020000) + Name (_UID, 0x00) + Name (_BBN, 0x02) + + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x18 }, //PCIE IRQ24-IRQ27 + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x19 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1B }, + }) + } //end of PCIEG + + Device (PEX0) + { + Name (_ADR, 0x00030000) + Name (_UID, 0x00) + Name (_BBN, 0x03) + + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x1C }, //PCIE IRQ28-IRQ31 + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x1D }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1E }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1F }, + }) + } //end of PEX0 + + Device (PEX1) + { + Name (_ADR, 0x00030001) + Name (_UID, 0x00) + Name (_BBN, 0x04) + + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x20 }, //PCIE IRQ32-IRQ35 + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x21 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x22 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x23 }, + }) + } //end f PEX1 + + Device (PEX2) + { + Name (_ADR, 0x00030002) + Name (_UID, 0x00) + Name (_BBN, 0x05) + + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x24 }, //PCIE IRQ36-IRQ39 + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x25 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x26 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x27 }, + }) + } //end f PEX2 + + Device (PEX3) + { + Name (_ADR, 0x00030003) + Name (_UID, 0x00) + Name (_BBN, 0x06) + + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x28 }, //PCIE IRQ40-IRQ43 + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x29 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x2A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x2B }, + }) + } //end f PEX3 + + Device (ISA) { + Name (_ADR, 0x00110000) + + /* Keyboard seems to be important for WinXP install */ + Device (KBD) + { + Name (_HID, EisaId ("PNP0303")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () + { + IO (Decode16, + 0x0060, // Address Range Minimum + 0x0060, // Address Range Maximum + 0x01, // Address Alignment + 0x01, // Address Length + ) + IO (Decode16, + 0x0064, // Address Range Minimum + 0x0064, // Address Range Maximum + 0x01, // Address Alignment + 0x01, // Address Length + ) + IRQNoFlags () + {1} + }) + Return (TMP) + } + } + + /* PS/2 mouse */ + Device (MOU) + { + Name (_HID, EisaId ("PNP0F13")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () + { + IRQNoFlags () {12} + }) + Return (TMP) + } + } + + /* PS/2 floppy controller */ + Device (FDC0) + { + Name (_HID, EisaId ("PNP0700")) + Method (_STA, 0, NotSerialized) + { + Return (0x0F) + } + Method (_CRS, 0, NotSerialized) + { + Name (BUF0, ResourceTemplate () + { + IO (Decode16, 0x03F2, 0x03F2, 0x00, 0x04) + IO (Decode16, 0x03F7, 0x03F7, 0x00, 0x01) + IRQNoFlags () {6} + DMA (Compatibility, NotBusMaster, Transfer8) {2} + }) + Return (BUF0) + } + } //FD END + + } //ISA END + + } // End of PCI0 + + + } // End of _SB + +} // End of Definition Block +
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/fadt.c =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/fadt.c (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/fadt.c 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,151 @@ +/* + * ACPI - create the Fixed ACPI Description Tables (FADT) + * (C) Copyright 2004 Nick Barker nick.barker9@btinternet.com + * (C) Copyright 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <string.h> +#include <arch/acpi.h> +#include <../../../southbridge/via/vt8237r/vt8237r.h> + +void acpi_create_fadt(acpi_fadt_t * fadt, acpi_facs_t * facs, void *dsdt) +{ + acpi_header_t *header = &(fadt->header); + + memset((void *) fadt, 0, sizeof(acpi_fadt_t)); + memcpy(header->signature, "FACP", 4); + header->length = 244; + header->revision = 1; + memcpy(header->oem_id, "LXBIOS", 6); + memcpy(header->oem_table_id, "LXBACPI ", 8); + memcpy(header->asl_compiler_id, "IASL", 4); + header->asl_compiler_revision = 0; + + fadt->firmware_ctrl = facs; + fadt->dsdt = dsdt; + fadt->preferred_pm_profile = 0; + fadt->sci_int = 9; + fadt->smi_cmd = 0; + fadt->acpi_enable = 0; + fadt->acpi_disable = 0; + fadt->s4bios_req = 0x0; + fadt->pstate_cnt = 0x0; + + fadt->pm1a_evt_blk = VT8237R_ACPI_IO_BASE; + fadt->pm1b_evt_blk = 0x0; + fadt->pm1a_cnt_blk = VT8237R_ACPI_IO_BASE + 0x4; + fadt->pm1b_cnt_blk = 0x0; + fadt->pm2_cnt_blk = 0x0; + fadt->pm_tmr_blk = VT8237R_ACPI_IO_BASE + 0x8; + fadt->gpe0_blk = VT8237R_ACPI_IO_BASE + 0x20; + fadt->gpe1_blk = 0x0; + + fadt->pm1_evt_len = 4; + fadt->pm1_cnt_len = 2; + fadt->pm2_cnt_len = 0; + fadt->pm_tmr_len = 4; + fadt->gpe0_blk_len = 4; + fadt->gpe1_blk_len = 0; + fadt->gpe1_base = 0; + fadt->cst_cnt = 0; + fadt->p_lvl2_lat = 90; + fadt->p_lvl3_lat = 900; + fadt->flush_size = 0; + fadt->flush_stride = 0; + fadt->duty_offset = 0; + fadt->duty_width = 1; //?? + fadt->day_alrm = 0x7d; + fadt->mon_alrm = 0x7e; + fadt->century = 0x32; + /* fixme 5 - 10 */ + fadt->iapc_boot_arch = 0x1; + /* fixme */ + fadt->flags = 0x4a5; + + fadt->reset_reg.space_id = 0; + fadt->reset_reg.bit_width = 0; + fadt->reset_reg.bit_offset = 0; + fadt->reset_reg.resv = 0; + fadt->reset_reg.addrl = 0x0; + fadt->reset_reg.addrh = 0x0; + + fadt->reset_value = 0; + fadt->x_firmware_ctl_l = facs; + fadt->x_firmware_ctl_h = 0; + fadt->x_dsdt_l = dsdt; + fadt->x_dsdt_h = 0; + + fadt->x_pm1a_evt_blk.space_id = 1; + fadt->x_pm1a_evt_blk.bit_width = 4; + fadt->x_pm1a_evt_blk.bit_offset = 0; + fadt->x_pm1a_evt_blk.resv = 0; + fadt->x_pm1a_evt_blk.addrl = VT8237R_ACPI_IO_BASE; + fadt->x_pm1a_evt_blk.addrh = 0x0; + + fadt->x_pm1b_evt_blk.space_id = 1; + fadt->x_pm1b_evt_blk.bit_width = 4; + fadt->x_pm1b_evt_blk.bit_offset = 0; + fadt->x_pm1b_evt_blk.resv = 0; + fadt->x_pm1b_evt_blk.addrl = 0x0; + fadt->x_pm1b_evt_blk.addrh = 0x0; + + fadt->x_pm1a_cnt_blk.space_id = 1; + fadt->x_pm1a_cnt_blk.bit_width = 2; + fadt->x_pm1a_cnt_blk.bit_offset = 0; + fadt->x_pm1a_cnt_blk.resv = 0; + fadt->x_pm1a_cnt_blk.addrl = VT8237R_ACPI_IO_BASE + 0x4; + fadt->x_pm1a_cnt_blk.addrh = 0x0; + + fadt->x_pm1b_cnt_blk.space_id = 1; + fadt->x_pm1b_cnt_blk.bit_width = 2; + fadt->x_pm1b_cnt_blk.bit_offset = 0; + fadt->x_pm1b_cnt_blk.resv = 0; + fadt->x_pm1b_cnt_blk.addrl = 0x0; + fadt->x_pm1b_cnt_blk.addrh = 0x0; + + fadt->x_pm2_cnt_blk.space_id = 1; + fadt->x_pm2_cnt_blk.bit_width = 0; + fadt->x_pm2_cnt_blk.bit_offset = 0; + fadt->x_pm2_cnt_blk.resv = 0; + fadt->x_pm2_cnt_blk.addrl = 0x0; + fadt->x_pm2_cnt_blk.addrh = 0x0; + + fadt->x_pm_tmr_blk.space_id = 1; + fadt->x_pm_tmr_blk.bit_width = 4; + fadt->x_pm_tmr_blk.bit_offset = 0; + fadt->x_pm_tmr_blk.resv = 0; + fadt->x_pm_tmr_blk.addrl = VT8237R_ACPI_IO_BASE + 0x8; + fadt->x_pm_tmr_blk.addrh = 0x0; + + fadt->x_gpe0_blk.space_id = 1; + fadt->x_gpe0_blk.bit_width = 0; + fadt->x_gpe0_blk.bit_offset = 0; + fadt->x_gpe0_blk.resv = 0; + fadt->x_gpe0_blk.addrl = VT8237R_ACPI_IO_BASE + 0x20; + fadt->x_gpe0_blk.addrh = 0x0; + + fadt->x_gpe1_blk.space_id = 1; + fadt->x_gpe1_blk.bit_width = 0; + fadt->x_gpe1_blk.bit_offset = 0; + fadt->x_gpe1_blk.resv = 0; + fadt->x_gpe1_blk.addrl = 0x0; + fadt->x_gpe1_blk.addrh = 0x0; + + header->checksum = + acpi_checksum((void *) fadt, sizeof(acpi_fadt_t)); +}
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mainboard.c =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mainboard.c (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mainboard.c 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,31 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <device/pci_ops.h> +#include "chip.h" + +#if CONFIG_CHIP_NAME == 1 +struct chip_operations mainboard_asus_a8v_e_se_ops = { + CHIP_NAME("ASUS A8V-E SE Mainboard") +}; +#endif
Added: trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mptable.c =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mptable.c (rev 0) +++ trunk/LinuxBIOSv2/src/mainboard/asus/a8v-e_se/mptable.c 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,161 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License v2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <arch/smp/mpspec.h> +#include <string.h> +#include <stdint.h> + +#include <../../../southbridge/via/vt8237r/vt8237r.h> +#include <../../../southbridge/via/k8t890/k8t890.h> + +void *smp_write_config_table(void *v) +{ + static const char sig[4] = "PCMP"; + static const char oem[8] = "LNXB "; + static const char productid[12] = "A8V-E SE "; + struct mp_config_table *mc; + unsigned int conforms = 0; + int bus_isa = 42; + + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); + + memcpy(mc->mpc_signature, sig, sizeof(sig)); + mc->mpc_length = sizeof(*mc); /* initially just the header */ + mc->mpc_spec = 0x04; + mc->mpc_checksum = 0; /* not yet computed */ + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + mc->mpc_oemptr = 0; + mc->mpc_oemsize = 0; + mc->mpc_entry_count = 0; /* No entries yet... */ + mc->mpc_lapic = LAPIC_ADDR; + mc->mpe_length = 0; + mc->mpe_checksum = 0; + mc->reserved = 0; + + smp_write_processors(mc); + + +/*Bus: Bus ID Type*/ + smp_write_bus(mc, 0, "PCI "); + smp_write_bus(mc, 1, "PCI "); + smp_write_bus(mc, 2, "PCI "); + smp_write_bus(mc, 3, "PCI "); + smp_write_bus(mc, 4, "PCI "); + smp_write_bus(mc, 5, "PCI "); + smp_write_bus(mc, 6, "PCI "); + smp_write_bus(mc, bus_isa, "ISA "); +/*I/O APICs: APIC ID Version State Address*/ + + smp_write_ioapic(mc, VT8237R_APIC_ID, 0x20, VT8237R_APIC_BASE); + smp_write_ioapic(mc, K8T890_APIC_ID, 0x20, K8T890_APIC_BASE); + + + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, VT8237R_APIC_ID, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, VT8237R_APIC_ID, 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, VT8237R_APIC_ID, 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, VT8237R_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, VT8237R_APIC_ID, 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x5, VT8237R_APIC_ID, 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, VT8237R_APIC_ID, 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, VT8237R_APIC_ID, 0x7); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, VT8237R_APIC_ID, 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x9, VT8237R_APIC_ID, 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xa, VT8237R_APIC_ID, 0xa); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xb, VT8237R_APIC_ID, 0xb); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, VT8237R_APIC_ID, 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, VT8237R_APIC_ID, 0xd); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, VT8237R_APIC_ID, 0xe); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, VT8237R_APIC_ID, 0xf); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 0, VT8237R_APIC_ID, 0x10); //IRQ16 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 1, VT8237R_APIC_ID, 0x11); //IRQ17 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 2, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xb << 2) | 3, VT8237R_APIC_ID, 0x13); //IRQ19 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 0, VT8237R_APIC_ID, 0x11); //IRQ17 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 1, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 2, VT8237R_APIC_ID, 0x13); //IRQ19 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xc << 2) | 3, VT8237R_APIC_ID, 0x10); //IRQ16 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 0, VT8237R_APIC_ID, 0x12); //IRQ18 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 1, VT8237R_APIC_ID, 0x13); //IRQ19 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 2, VT8237R_APIC_ID, 0x10); //IRQ16 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xd << 2) | 3, VT8237R_APIC_ID, 0x11); //IRQ17 + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xf << 2) | 0, VT8237R_APIC_ID, 0x14); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0xf << 2) | 1, VT8237R_APIC_ID, 0x14); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 0, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 1, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x10 << 2) | 2, VT8237R_APIC_ID, 0x15); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x11 << 2) | 2, VT8237R_APIC_ID, 0x16); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 0, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 1, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 2, K8T890_APIC_ID, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x2 << 2) | 3, K8T890_APIC_ID, 0x3); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 0, K8T890_APIC_ID, 0x7); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 1, K8T890_APIC_ID, 0xb); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 2, K8T890_APIC_ID, 0xf); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, (0x3 << 2) | 3, K8T890_APIC_ID, 0x13); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 0, K8T890_APIC_ID, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 1, K8T890_APIC_ID, 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 2, K8T890_APIC_ID, 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, (0x00 << 2) | 3, K8T890_APIC_ID, 0x3); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 0, K8T890_APIC_ID, 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 1, K8T890_APIC_ID, 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 2, K8T890_APIC_ID, 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x00 << 2) | 3, K8T890_APIC_ID, 0x7); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 0, K8T890_APIC_ID, 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 1, K8T890_APIC_ID, 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 2, K8T890_APIC_ID, 0xa); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x00 << 2) | 3, K8T890_APIC_ID, 0xb); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 0, K8T890_APIC_ID, 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 1, K8T890_APIC_ID, 0xd); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 2, K8T890_APIC_ID, 0xe); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x5, (0x00 << 2) | 3, K8T890_APIC_ID, 0xf); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 0, K8T890_APIC_ID, 0x10); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 1, K8T890_APIC_ID, 0x11); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 2, K8T890_APIC_ID, 0x12); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 3, K8T890_APIC_ID, 0x13); + +/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1); + /* There is no extension information... */ + + /* Compute the checksums */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + return smp_next_mpe_entry(mc); +} + +unsigned long write_smp_table(unsigned long addr) +{ + void *v; + v = smp_write_floating_table(addr); + return (unsigned long)smp_write_config_table(v); +}
Added: trunk/LinuxBIOSv2/targets/asus/a8v-e_se/Config.lb =================================================================== --- trunk/LinuxBIOSv2/targets/asus/a8v-e_se/Config.lb (rev 0) +++ trunk/LinuxBIOSv2/targets/asus/a8v-e_se/Config.lb 2007-11-02 23:17:57 UTC (rev 2934) @@ -0,0 +1,62 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2007 Rudolf Marek r.marek@assembler.cz +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License v2 as published by +## the Free Software Foundation. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +target a8v-e_se +mainboard asus/a8v-e_se + +romimage "normal" +# 48K for SCSI FW +# option ROM_SIZE = 475136 +# option ROM_SIZE = 512*1024-36*1024 + option ROM_SIZE = 512*1024 +# 48K for SCSI FW and 48K for ATI ROM +# option ROM_SIZE = 425984 +# 64K for Etherboot +# option ROM_SIZE = 458752 +# option USE_FAILOVER_IMAGE=0 + option USE_FALLBACK_IMAGE=0 + +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x18800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" + +# give path to filo.elf if needed + payload filo.elf +end + +romimage "fallback" + option USE_FALLBACK_IMAGE=1 +# option USE_FAILOVER_IMAGE=0 + +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x19800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" + +# give path to filo.elf if needed + + payload filo.elf +end + +buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"